LiNi_(0.5)Mn_(0.5)O_2制备及表征

采用共沉淀法制备了LiNi0.5Mn0.5O2.XRD,Raman测试都表明材料是六方结构.XPS检测得出镍主要以正二价存在,锰元素主要以正四价存在.合成的LiNi0.5Mn0.5O2得到了50次的循环,但比容量较低.充放电循环性能比较研究表明,经过40次循环后,0.3,0.6,1.5 C的放电比容量分别是65.88,61.56,52.23 mA.h.g-1.     

溶胶-凝胶法制备Bi0.5Na0.5TiO3陶瓷及其电学特性

用溶胶-凝胶工艺成功制备出Bi05Na05TiO3纳米微粉，并利用此微粉烧结出高致密度的Bi05Na05TiO3陶瓷.这种新工艺制备的Bi05Na05TiO3陶瓷，其压电性能远远高于普通方法制备的陶瓷，其中压电常数d33和机电耦合系数kt分别高达102×10-12C/N和58%.同时发现，对于这种Bi05Na05TiO3陶瓷，室温时只需施加100kV/cm左右的交变电场，就可得到矩形度极好的饱和回线，得到的剩余极化Pr和矫顽场Ec分别为32μC/cm2和61kV/cm.而在100℃以上只需施加35kV/cm的极化电场就可使样品充分极化.     

Effect of the aluminium doping on the microstructure and morphology of LiNi0.5Co0.5O2 oxides

LiCo_1−xNi_xO₂ materials having the layeredα-NaFeO₂-type structure are promising positive electrodes for advanced lithium-ion batteries. Their electrochemical performance is very much conditioned by the integrity of the lamellar structure that needs to be stable enough to stand many charge/discharge cycles. LiNi_0.5−xAl_xCo_0.5O₂ (0≤x≤0.3) samples have been prepared by a low-temperature route, the sol-gel method assisted by succinic acid as chelating agent. We study in detail their crystallographic structure by XRD, their chemical composition by ICP and their morphology by SEM. Their local cationic environment is also carried out by means of FTIR spectroscopy. Paper presented at the 8th EuroConference on Ionics, Carvoeiro, Algarve, Portugal, Sept. 16 – 22, 2001.     

Enhanced electrochemical performances of LiNi0.5Co0.2Mn0.3O2 cathode material co-coated by graphene/TiO2

The electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523) layered cathode material, such as poor rate capacity and cycling stability caused by undesirable intrinsic conductivity and low rate of lithium ion transportation, are not fairly good especially at elevated rate and cut-off voltage. To improve these properties, in this study, the co-coating layer of graphene and TiO₂ was constructed on NCM523 surface. The graphene/TiO₂ coating layer could effectively prevent hydrofluoric acid (HF) attacks, suppress the side reaction, accelerate the lithium ion diffusion and facilitate the electron migration. The enhancement of cycle performance and rate capacity was contributed to the uniform co-modified surface, interacting each other and thus exhibiting synergistic effects.     

Structure and magnetic properties of Ni0.5Zn0.5Mn0.5-xMoxFe1.5O4 ferrites prepared by sol-gel auto-combustion method

A series of Mo doped Ni-Mn-Zn ferrites compounds with the formula Ni_0.5Zn_0.5Mn_0.5-xMo_xFe_1.5O₄ (x = 0, 0.025, 0.05, 0.075 and 0.1) were first synthesized by sol-gel auto-combustion method. The X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), and vibrating sample magnetometer (VSM) analysis were carried out to characterize the microstructural and magnetic properties of ferrites. Rietveld refinement of X-ray diffraction data confirmed the formation of cubic spinel structure and the emergence of FeMoO₄ phase with the substitution of Mo⁶⁺ contents. The grain size increased remarkably due to the formation of the liquid phase. The saturation magnetization (M_s) increased while the coercivity (H_c) decreased from 67.3 to 12.1 Oe due to the decrease of magneto-crystalline anisotropy constant. The initial permeability (μ_i) increased significantly from 34 (x = 0) to 114 (x = 0.075) and later decreased for x = 0.1. In our experiment, Ni_0.5Zn_0.5Mn_0.425Mo_0.075Fe_1.5O₄ ferrite presented the best microstructure and soft magnetic properties.     

溶胶-凝胶法制备的GeO2-SiO2凝胶玻璃的红光发射

以3三氯锗丙酸和正硅酸乙酯为原料采用溶胶凝胶法制备了GeO2SiO2凝胶玻璃.室温下以532nm激光(Nd:YAG)激发GeO2SiO2凝胶玻璃有一强的发光峰,这种发光有两个发光带,其峰位分别在575nm和624nm.该发光现象是由镶嵌在GeO2SiO2凝胶玻璃中GeO2纳米颗粒产生的.利用吸收光谱和TEM对GeO2SiO2凝胶玻璃进行了表征,结果发现随着Ge含量的增加凝胶玻璃中GeO2纳米颗粒的尺寸越来越大,吸收边向低能边移动.X射线衍射和电子衍射确定GeO2SiO2凝胶玻璃中GeO2颗粒的结构为非晶结 关键词： GeO2-SiO2凝胶玻璃 溶胶-凝胶法 红光发射     

Ferroelectricity and ferromagnetism in fine-grained multiferroic BaTiO3/(Ni0.5Zn0.5)Fe2O4 composites prepared by a novel hybrid process

Dense, homogeneous, and fine-grained multiferroic BaTiO₃/(Ni_0.5Zn_0.5)Fe₂O₄ composite ceramics are synthesized by a novel powder-in-sol precursor hybrid processing route. This route includes the dispersion of nanosized BaTiO₃ ferroelectric powders prepared via conventional sold-state ceramic process into (Ni_0.5Zn_0.5)Fe₂O₄ ferromagnetic sol-gel precursor prepared via a sol-gel wet chemistry process. The composite ceramics show coexistence of obvious ferroelectric and ferromagnetic hysteresis loops at room temperature. Very low dielectric loss of about 0.02–0.0067 in the range of 10 kHz–10 MHz can be achieved, which is about an order of magnitude lower than the results of many reports using conventional processes at room temperature. The combination of high permeability and permittivity with low losses in the ceramics enables significant miniaturization of electronic devices based on the ceramics.     

Synthesis of LiNi0.6Co0.2Mn0.2O2 cathode material by a carbonate co-precipitation method and its electrochemical characterization

Using Na₂CO₃ and Me(NO₃)₂ (Me = Ni, Co and Mn) as starting materials, the precursor of LiNi_0.6Co_0.2Mn_0.2O₂ cathode material for lithium rechargeable batteries has been synthesized by carbonate co-precipitation. The precursor was mixed with Li₂CO₃ and heated in air. Thermogravimetric analysis (TG–DTA), laser particle size analysis, X-ray diffraction (XRD) and electron scanning microscopy (SEM) were employed to study the reaction process and the structures of the powders. The D₅₀ of precursor was 2.509 μm and the distribution was relatively narrow. The optimum calcination temperature was 850–900 °C. Galvanostatic cell cycling and cyclic voltammetry were also used to evaluate the electrochemical properties. The initial discharge capacity for the powders calcined at 900 °C was about 180 mA h/g at room temperature when cycled between 2.8 and 4.3 V at 0.2 C rate.     

Structure and insertion properties of disordered and ordered LiNi0.5Mn1.5O4 spinels prepared by wet chemistry

We present the synthesis, characterization, and electrode behavior of LiNi_0.5Mn_1.5O₄ spinels prepared by the wet-chemical method via citrate precursors. The phase evolution was studied as a function of nickel substitution and upon intercalation and deintercalation of Li ions. Characterization methods include X-ray diffraction, SEM, Raman, Fourier transform infrared, superconducting quantum interference device, and electron spin resonance. The crystal chemistry of LiNi_0.5Mn_1.5O₄ appears to be strongly dependent on the growth conditions. Both normal-like cubic spinel [Fd3m space group (SG)] and ordered spinel (P4 ₁ 32 SG) structures have been formed using different synthesis routes. Raman scattering and infrared features indicate that the vibrational mode frequencies and relative intensities of the bands are sensitive to the covalency of the (Ni, Mn)-O bonds. Scanning electron microscopy (SEM) micrographs show that the particle size of the LiNi_0.5Mn_1.5O₄ powders ranges in the submicronic domain with a narrow grain-size distribution. The substitution of the 3d⁸ metal for Mn in LiNi_0.5Mn_1.5O₄ oxides is beneficial for its charge–discharge cycling performance. For a cut-off voltage of 3.5–4.9 V, the electrochemical capacity of the Li//LiNi_0.5Mn_1.5O₄ cell is ca. 133 mAh/g during the first discharge. Differences and similarities between LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ oxides are discussed.     

Characterization of ZnO and Zn0.95Co0.05O prepared by sol-gel method using PAC spectroscopy

We report on the first NMR study of ⁷³Ge nuclear spin decoherence in germanium single crystals with different abundance of the ⁷³Ge isotope. Hahn echo decays are well fit by a superposition of two exponentials. The deviation from the single exponential is more pronounced in the more spin-diluted sample, causing long-lived echoes. We show that the decay of these echoes becomes slower with the reduction of ⁷³Ge abundance and is therefore caused by dipole–dipole interaction, reflecting the fundamental decoherence process in the spin system. The fast decay at the beginning of the relaxation process is shown to be mainly caused by the quadrupole interaction. Our experimental findings are supported by the calculations of Hahn echo decays in the germanium crystals under study. Quite good agreement between the theory and experiment is demonstrated.     

Improved electrochemical properties of Sr2+-doped LiNi0.8Co0.2O2 synthesized via a sol-gel route using tartaric acid as a chelating agent

Single-phase undoped LiNi_0.8Co_0.2O₂ and Sr²⁺-doped LiNi_0.8Co_0.2O₂ were synthesized by a low temperature tartaric acid assisted sol-gel method. Small quantities of Sr²⁺ were used as dopants in order to improve the electrochemical characteristics, especially the capacity and cycling performance of LiNi_0.8Co_0.2O₂. The electrochemical performance of the undoped material was promising with a first discharge capacity of 174 mAh/g and 165 mAh/g after 10 cycles with a 100% cycling efficiency in the tenth cycle. Addition of Sr²⁺ for Li in minimum quantities with the Sr²⁺/Li⁺ dopant mole ratio ranging from 10⁻⁴ to 10⁻⁸ resulted in improved electrochemical properties for dopant mole ratio of 10⁻⁶. The first discharge capacity was 182 mAh/g and the tenth was 174 mAh/g at the 10th discharge. The synthesis of Sr²⁺-doped LiNi_0.8Co_0.2O₂ and its improved electrochemical properties have been discussed for the first time. The improved electrochemical properties of Sr²⁺-doped LiNi_0.8Co_0.2O₂ system are explained based on defect models.     

Fatigue-free Pb(Zr0.52Ti0.48)O3 thin films on indium tin oxide coated substrates by a sol-gel process

Fatigue-free Pb(Zr_0.52Ti_0.48)O₃ (PZT) ferroelectric thin films were successfully prepared on indium tin oxide (ITO) coated glass substrates using the sol-gel method combined with a rapid thermal annealing process (RTA). The films post-annealed at a temperature of 700 °C for 2 min by RTA process formed (110)-oriented Pb(Zr_0.52Ti_0.48)O₃ thin films with pure perovskite structure, and had a good morphology as well. The good ferroelectricity of the prepared PZT films was confirmed by P–E hysteresis loop measurements. Fatigue characteristics showed stable behavior. Degradation in polarization was not found while the repeating cycles were up to 10¹¹, and a low leakage current density of 10⁻⁸ A/cm² was also obtained from the highly fatigue-resisted PZT thin films on ITO/glass substrates. Received: 19 October 1998 / Accepted: 29 March 1999 / Published online: 26 May 1999     

Photoluminescent properties of boehmite whisker prepared by sol-gel process

A boehmite whisker powder with the aspect ratio and mean diameter of 10-40 and 2-6 nm was prepared by the sol-gel process using aluminum alkoxide as precursor. The main absorption bands located at 234 (5.31 eV), and 254.5 (4.88 eV) nm are presented in the excitation spectrum of sample. It is observed that all the spectra show two main broad bands emission whose maximum shows a large shift, which depends on the excitation wavelength. It is suggested that the ultraviolet photoluminescence emission in boehmite whisker prepared by the sol-gel process may be associated with anionic vacancies (F and F⁺ centers, or grouping of these two types of defects), and the non-bridging oxygen hole center (NBOHC)=Al-O.     

Enhanced electrochemical performances of layered LiNi0.5Mn0.5O2 as cathode materials by Ru doping for lithium-ion batteries

Ionics - The pristine and Ru-doped LiNi0.5Mn0.5O2 cathode materials are synthesized by a wet chemical method, followed by a high-temperature calcination process. The influence of Ru substitution on...     

Crystal structure and spin state of Fe0.5Co0.5(NCS)2(bpa)2

Fe(NCS)₂(bpa)₂, Co(NCS)₂(bpa)₂, and Fe_0.5Co_0.5(NCS)₂(bpa)₂ were synthesized. X-ray structural analysis revealed that the structure was the same among the three complexes. Although the metal-ligand distance in the mixed crystals was shorter than the distance in Fe(NCS)₂(bpa)₂ and was similar to that in Co(NCS)₂(bpa)₂, the spin state remained temperature-independent Fe^II high-spin state in ⁵⁷Fe M?ssbauer spectra.     

Structural and electrical properties of polycrystalline PbZr0.5Ti0.5O3 films deposited on La0.5Sr0.5CoO3 coated silicon by sol-gel process

La_0.5Sr_0.5CoO₃ (LSCO) films have been grown on Si (100) by a metalorganic chemical liquid deposition (MOCLD) technique using lanthanum acetate, strontium acetate and cobalt acetate as the starting materials. Subsequent PbZr_0.5Ti_0.5O₃ (PZT) films were deposited onto LSCO films by a modified sol-gel method. Field-emission scanning electron microscopy and X-ray diffraction analysis show that PZT and LSCO films are polycrystalline and entirely perovskite phase. At an applied electric field of 250 kV/cm, the Pt/PZT/LSCO capacitor shows no polarization fatigue after 3×10⁹ switching cycles and an internal electric field; the remnant polarization P_r and the coercive field E_c are about 22 μC/cm² and 73 kV/cm, respectively. The dielectric constant of PZT films is 650 at a frequency of 1 kHz. Received: 20 February 2001 / Accepted: 6 June 2001 / Published online: 30 August 2001     

Physical characterization and vibrational spectroscopy of Bi(Pb) cuprate 2212 ceramics prepared by sol-gel

Samples of bismuth cuprate with and without lead substitution were prepared by the sol-gel method. The general formula was Bi_2−xPb_xSr₂CaCu₂O_8+δ, where 0≤x≤0.6. The samples were characterized by X-ray diffraction (XRD), electron probe microanalysis (EPMA), magnetic susceptibility, Raman spectroscopy and IR reflectance. Regarding homogeneity, density, purity and superconductivity, optimal behavior was found x = 0.2-0.4. An increase of hole concentration in the CuO₂-planes with Pb²⁺/Bi³⁺ ratio was observed from the optical data. The Raman spectra modifications with lead substitution are discussed. Evidence of the interaction between CuO₂-plane hole continuum and 150 cm⁻¹ IR active modes was found.     

Structural,magnetic and dielectric properties of (Li1+, Al3+) co-doped Ni0.5Zn0.5Fe2O4 ferrite ceramics prepared by the sol-gel auto-combustion method

(Li¹⁺, Al³⁺) co-doped Ni_0.5Zn_0.5Fe₂O₄ ferrites, Ni_0.5-xZn_0.5-xLi_xAl_xFe₂O₄ (x = 0.000, 0.025, 0.050 and 0.100), were synthesized by the sol-gel auto-combustion method. X-ray diffraction (XRD), field emission scanning electronic microscope (FESEM), vibrating sample magnetometer (VSM) and LCR meter were used to investigate the structural, magnetic and dielectric properties. Results of XRD and SEM indicate that both doping amount and calcination temperature play significant roles in crystal structure and grain growth. Also, it can be observed that the saturation magnetization and the coercivity change in a noticeable manner. The Ni_0.475Zn_0.475Li_0.025Al_0.025Fe₂O₄ ferrite sintered at 1200 °C has a relatively low coercivity value (62.93 Oe) and the largest saturation magnetization (110.95 emu/g). Besides, dielectric behavior is also improved by Li¹⁺ and Al³⁺ co-doping.     

Multi-faceted highly crystalline LiMn2O4 and LiNi0.5Mn1.5O4 cathodes synthesized by a novel carbon exo-templating method

LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ powders have been synthesized by a novel cost-effective carbon exo-templating process. It has been observed that controlled nucleation in the pores of highly surface active carbon produces a distinct effect on the powder morphology and crystallinity. Quantitative X-ray phase analyses show single phase spinel structure having Fd3m symmetry for both samples. Field emission electron microscopy reveals particles of size 0.5–1.0 µm with well defined multi-faceted crystals. Cyclic voltammetry results show well separated distinct redox peaks at 4.05/3.92 and 4.17/4.08 V for LiMn₂O₄/Li and 4.91/4.61 V for LiNi_0.5Mn_1.5O₄/Li coin cells indicating good crystallinity and reversibility of the cathodes compared to that of pristine LiMn₂O₄ synthesized by conventional combustion process. The LiMn₂O₄/Li and LiNi_0.5Mn_1.5O₄/Li cells deliver an initial discharge capacity of 110 mA h/g and 122 mA h/g respectively at a current density of 0.05 mA/cm² and when cycled at 0.2 mA/cm², the cells maintain 81% and 96% of their initial discharge capacity respectively even after 20 cycles. On the other hand, at the same current density, LiMn₂O₄ synthesized by conventional combustion process suffers from severe capacity fading (only 37.5% capacity retention after the 25th cycle). The capacity fading rate is found to be very less even at further higher current densities (0.4–0.8 mA/cm²) for both LiMn₂O₄/Li and LiNi_0.5Mn_1.5O₄/Li cells synthesized by the templating process. The present study reveals that high crystallinity along with multi-faceted morphology shows a remarkable enhancement in capacity as well as rate performance of pristine LiMn₂O₄ and its Ni derivative.