The laser pulse from a rf waveguide CO2 laser

The behaviour of a rf-excited waveguide CO₂ laser in the pulse regime is studied experimentally. The specific time sections of the pulse have been defined and described in detail. The output pulse evolution versus input power, pressure of the laser mixture, output coupling, repetition frequency and pulse width has been investigated. The spectral content of the pulse has been analysed. A model explaining the effect of laser tuning during the pulse duration is given. The ultrahigh pulse (UHP), defined as the pulse for which the bulge effect occurs, is predicted. Received: 22 October 2002 / Revised version: 13 January 2003 / Published online: 26 March 2003 RID="*" ID="*"Corresponding author. Fax: +48-71/3203-189, E-mail: eda@zr.ita.pwr.wroc.pl     

Self-adaptive Nd:YLF holographic laser with selectable wavelength operation

We demonstrate, for the first time to our knowledge, operation of a self-adaptive holographic laser with wavelength selection, which uses Nd:YLF as the gain medium. The holographic laser was self-starting and, by virtue of the temporal dynamics in writing the gain grating, passively Q-switched the cavity to produce pulses with 20–50 ns duration. A pulse energy of 184 mJ was obtained from the system with beams having a TEM₀₀ spatial profile. Single-longitudinal-mode operation was observed with near-transform-limited bandwidth. Received: 30 July 2002 / Revised version: 1 October 2002 / Published online: 26 February 2003 RID="*" ID="*"Corresponding author. Fax: +44-20/7594-7744, E-mail: s.y.lam@ic.ac.uk     

Sub-nanosecond microchip laser with intracavity Raman conversion

Efficient sub-nanosecond pulse operation of microchip lasers with intracavity Raman conversion and pulse compression is presented for the first time. The microchip lasers were composed of Nd:LSB or Nd:YAG laser crystals, Cr⁴⁺:YAG saturable absorber, and Ba(NO₃)₂ Raman medium. The pulse duration obtained at the Stokes wavelength (1196 nm) was as short as 118 ps. Optical conversion efficiency of laser-diode pump power to the Stokes power of 8% was reached. Pulse energy and peak power of Stokes emission were 1.2 μJ and 5.4 kW, correspondingly. Numerical calculations are in good agreement with obtained experimental results. Received: 20 December 2002 / Revised version: 6 March 2003 / Published online: 5 May 2003 RID="*" ID="*"Corresponding author. Fax: +1-716/645-6945, E-mail: ankuzmin@acsu.buffalo.edu RID="**" ID="**"Present address: University at Buffalo, SUNY, The Institute for Lasers, Photonics, and Biophotonics, 458 NSC, Buffalo, NY 14 260-3000, USA     

A UV–Visible–NIR fluorescence lifetime imaging microscope for laser-based biological sensing with picosecond resolution

This article describes the design and characterization of a wide-field, time-domain fluorescence lifetime imaging microscopy (FLIM) system developed for picosecond time-resolved biological imaging. The system consists of a nitrogen-pumped dye laser for UV–visible–NIR excitation (337.1–960 nm), an epi-illuminated microscope with UV compatible optics, and a time-gated intensified CCD camera with an adjustable gate width (200 ps-10^-3 s) for temporally resolved, single-photon detection of fluorescence decays with 9.6-bit intensity resolution and 1.4-μm spatial resolution. Intensity measurements used for fluorescence decay calculations are reproducible to within 2%, achieved by synchronizing the ICCD gate delay to the excitation laser pulse via a constant fraction optical discriminator and picosecond delay card. A self-consistent FLIM system response model is presented, allowing for fluorescence lifetimes (0.6 ns) significantly smaller than the FLIM system response (1.14 ns) to be determined to 3% of independently determined values. The FLIM system was able to discriminate fluorescence lifetime differences of at least 50 ps. The spectral tunability and large temporal dynamic range of the system are demonstrated by imaging in living human cells: UV-excited endogenous fluorescence from metabolic cofactors (lifetime ∼1.4 ns); and 460-nm excited fluorescence from an exogenous oxygen-quenched ruthenium dye (lifetime ∼400 ns). Received: 23 February 2003 / Published online: 22 May 2003 RID="*" ID="*"Corresponding author. Fax: +1-734/9361-905, E-mail: mycek@umich.edu     

Concatenation of plasma filaments created in air by femtosecond infrared laser pulses

We report the first observation of the attachment of two single plasma filaments created collinearly in the atmosphere by IR femtosecond laser pulses. The linked filamentary structure is electrically conductive and emits sub-THz radiation over its entire length. Concatenation is achieved only for a specific time ordering between the two initial laser pulses. The pulse producing the filament closer to the laser source must be retarded with respect to the other pulse. This special time ordering is attributed to the acceleration of light in a self-guided pulse. Received: 4 March 2003 / Published online: 14 May 2003 RID="*" ID="*"Corresponding author. Fax: +33-1/6931-9996, E-mail: stzortz@ensta.fr     

A LIDAR technique to measure the filament length generated by a high-peak power femtosecond laser pulse in air

We demonstrate a new method for measuring the length of a femtosecond laser pulse induced filament in air using a LIDAR (LIght Detection And Ranging) technique. The LIDAR involves a detector with a fast response time. The back-scattered multiphoton induced fluorescence from nitrogen molecules excited inside the filament is measured, from which the length of the filament can be determined. We find good agreement between the measured filament length and the length estimated from burn patterns on paper. In addition, good qualitative agreement between the experimental measurement and numerical simulations is obtained for the signal features of the filament. We propose that this new method can be used to quantitatively determine filamentation at longer distances. Received: 11 June 2002 / Revised version: 21 October 2002 / Published online: 5 February 2003 RID="*" ID="*"Corresponding author. Fax: +1-418/656-2623, E-mail: aiwasaki@phy.ulaval.ca     

Seven-terawatt Ti:sapphire laser system operating at 50 Hz with high beam quality for laser Compton femtosecond X-ray generation

We present a 7-TW Ti:sapphire laser system operating at 50 Hz for laser Compton femtosecond X-ray generation. This laser system delivers 8.4 W of average output power at a repetition rate of 50 Hz with a pulse width of 24 fs. It demonstrates successful management using a dynamically stable resonator in the regenerative amplifier and compensation for thermal lensing by a convex mirror in a ring-type four-pass power amplifier. We also present the results of closed-loop corrections for distorted wavefronts of amplified and compressed laser pulses, using an adaptive optical system consisting of a Shack–Hartmann-type wavefront sensor and a deformable mirror. This closed-loop correction results in dramatic improvements, reducing wavefront distortions below 0.05 λ rms. Received: 31 October 2002 / Revised version: 3 March 2003 / Published online: 5 May 2003 RID="*" ID="*"Corresponding author. Fax: +81-298/61-3349, E-mail: ito@festa.or.jp     

High-repetition-rate eye-safe optical parametric oscillator intracavity pumped by a diode-pumped Q-switched Nd:YVO<Subscript>4</Subscript> laser

A high-repetition-rate eye-safe optical parametric oscillator (OPO), using a non-critically phase-matched KTP crystal intracavity pumped by an acousto-optically (AO) Q-switchedNd:YVO₄ laser, is experimentally demonstrated. It is found that the average OPO signal power at 1573 nm can be efficiently increased by increasing the pulse repetition rate. Moreover, the intracavity OPO process effectively shortens the pulse width so that it is in the range 5∼8 ns for pulse repetition rates of 10 to 80 kHz. As a result of the relatively short pulse, the peak power at 1573 nm is higher than 2 kW at a pulse repetition rate of 80 kHz. Received: 10 July 2002 / Published online: 26 February 2003 RID="*" ID="*"Corresponding author. Fax: +886-35/729-134, E-mail: yfchen@cc.nctu.edu.tw     

Self-starting five optical cycle pulse generation in Cr<Superscript>4+</Superscript>:YAG laser

We report stable self-starting near-transform-limited 26-fs pulses at 250-mW output power from a Kerr-lens mode-locked (KLM) Cr⁴⁺:YAG laser using chirped mirrors in combination with prisms. The highest output power achieved in KLM regime was 600 mW at 55-fs pulse duration. The experimental results agree well with the results of theoretical analysis with respect to KLM self-starting ability and stability against continuous-wave and multi-pulse operation. Parameter ranges for stable transform-limited KLM pulses as well as the shortest achievable pulse durations are established. Using an InGaAs-InP semiconductor saturable absorber mirror we could obtain self-starting 57-fs pulses at the average output power of 200 mW. Two-photon absorption was found to be the main mechanism favoring the multiple-pulse operation. Received: 2 May 2002 / Revised version: 16 July 2002 / Published online: 8 January 2003 RID="*" ID="*"Corresponding author. Fax: +43-1/58801-38799, E-mail: sorokina@tuwien.ac.at     

High-power intracavity frequency doubling of a Ti:sapphire femtosecond oscillator

We demonstrate intracavity frequency doubling of a standard femtosecond Ti:sapphire oscillator. The cavity is extended with a pair of focusing mirrors and a 0.5-mm-thick BBO crystal. We achieve a repetition rate of 50 MHz and simultaneously generate 22 mW of 55-fs pulses at 810 nm and 200 mW of 73-fs pulses at 405 nm, which corresponds to 4 nJ per pulse. We create a total of 330-mW, 405-nm light when pumping the Ti:sapphire crystal with 5.7 W from an Ar-ion laser, corresponding to a conversion efficiency of 5.7%. No saturation is found, which implies that higher outputs can be achieved with higher pump rates. Preliminary results from the use of blue pulses as pump in an optical parametric amplifier seeded by pulses from a photonic crystal fiber are presented. Received: 27 January 2003 / Revised version: 27 March 2003 / Published online: 12 May 2003 RID="*" ID="*"Corresponding author. Fax: +45-861/96199, E-mail: tva@chem.au.dk     

Lasing action in air induced by ultra-fast laser filamentation

The backscattered fluorescence of nitrogen from filaments generated by intense ultra-fast Ti:sapphire laser pulses propagating in air is studied. The backscattered fluorescence from N₂ molecules and ions show an exponential increase with increasing filament length, indicating amplified spontaneous emission. Received: 11 October 2002 / Revised version: 3 December 2002 / Published online: 26 February 2003 RID="*" ID="*"Corresponding author. Fax: +1-418/6562-623, E-mail: qluo@phy.ulaval.ca     

Femtosecond laser pulse filamentation versus optical breakdown in H<Subscript>2</Subscript>O

The competition between femtosecond laser pulse induced optical breakdown and femtosecond laser pulse filamentation in condensed matter is studied both experimentally and numerically using water as an example. The coexistence of filamentation and breakdown is observed under tight focusing conditions. The development of the filamentation process from the creation of a single filament to the formation of many filaments at higher pulse energy is characterized systematically. In addition, strong deflection and modulation of the supercontinuum is observed. They manifest themselves at the beginning of the filamentation process, near the highly disordered plasma created by optical breakdown at the geometrical focus. Received: 9 July 2002 / Revised version: 15 November 2002 / Published online: 19 March 2003 RID="*" ID="*"Corresponding author. Fax: +1-418/6562-623, E-mail: wliu@phy.ulaval.ca     

Effects of a prepulse on laser-induced EUV radiation conversion efficiency

The influence of prepulses on the conversion efficiency (CE) of laser radiation into 13 nm extreme ultraviolet (EUV) radiation, resulting from lithium-like oxygen ions from O20 μm water droplets, was investigated. The laser pulse durations in the experiment ranged from 200 fs to 120 ps. Applying prepulses preceding the main pulse at various delays of up to 11 ns, it was shown that the CE increases differently for each measured pulse duration. The strongest dependence on the introduction of a prepulse was observed for 2 ps laser pulses with a 20 mJ laser pulse energy. The EUV CE was improved by a factor of 15 by the introduction of a prepulse. Calculations on the atomic physics of oxygen ions and simulations of the laser–plasma interaction revealed the influence of the prepulse on the EUV yield. Received: 25 October 2002 / Published online: 22 January 2003 RID="*" ID="*"Corresponding author. Fax: +49-3641/947-202, E-mail: duesterer@ioq.uni-jena.de     

Poincaré representation of polarization-shaped femtosecond laser pulses

The usage of Poincaré phase space for the representation of polarization-shaped femtosecond laser pulses is discussed. In these types of light fields the polarization state (i.e. ellipticity and orientation) changes as a function of time within a single laser pulse. Such deliberate variation can be achieved by frequency-domain femtosecond pulse shaping in which two polarization components are manipulated individually. Here it is shown how these light pulses can be represented as temporal trajectories through the ellipticity-orientation (Poincaré) phase space, whereas conventional light (either continuous-wave or pulsed) is determined by only one specific Poincaré location. General properties of parametric Poincaré trajectories are discussed, and their relation to experimentally accessible pulse-manipulation parameters (i.e. amplitudes and phases) determined. Specifically, it is shown how the maximum rate by which a given polarization state can be turned into a different one (at significant intensity levels) is limited by the spectral laser bandwidth. Apart from their direct usage in polarization-shaped pulse representation, Poincaré trajectories also form the basis for intuitive quasi-three-dimensional renderings of the electric field profile. There, the temporal evolution of polarization, intensity, and chirp is directly apparent in a single illustration. Received: 10 December 2002 / Published online: 24 April 2003 RID="*" ID="*"Corresponding author. Fax: +49-931/888-4906, E-mail: brixner@physik.uni-wuerzburg.de     

Fluorescence lidar imaging of the cathedral and baptistery of Parma

Extensive fluorescence multispectral imaging of the cathedral and baptistery of Parma, Italy, is reported and discussed. In particular, the first fluorescence imaging data from protection-treated stony materials were recorded. Fluorescence spectra were taken with a mobile lidar system scanning the monument surfaces with a frequency-tripled Nd:YAG laser beam from a distance of about 80 m. For each pixel of the area investigated, a high-spectral-resolution spectrum in the full visible range was acquired. The principal-component analysis technique was used to obtain thematic maps that outlined areas subject to protective treatment and biological growth, and other features, such as different types of stones and decoration pigments. Received: 24 July 2002 / Revised version: 16 January 2003 / Published online: 3 April 2003 RID="*" ID="*"Corresponding author. Fax: +39-055/410-893, E-mail: g.cecchi@ifac.cnr.it     

Measurement of filament length generated by an intense femtosecond laser pulse using electromagnetic radiation detection

We present a new method to measure the length of a filament induced by the propagation of intense femtosecond laser pulses in air. We used an antenna to detect electromagnetic pulses radiated from multipole moments inside the filament oscillating at the plasma frequency. The results are compared with the values detected from the backscattered fluorescence induced by multiphoton ionization of nitrogen molecules excited inside the filament. The values are found to be in good agreement. Received: 6 November 2002 / Revised version: 27 January 2003 / Published online: 24 April 2003 RID="*" ID="*"Corresponding author. Fax: +1-418/656-2623, E-mail: shosseini@phy.ulaval.ca     

Emission of laser pulses due to transitions from metastable to metastable levels in strontium vapor

Multi-line laser transitions from one metastable triplet state to another at wavelengths of 2.92, 3.01, 2.69 and 2.60 μm have been obtained through high pulse repetition frequency longitudinal discharge in a mixed gas of strontium vapor and helium buffer gas. The intensity ratio of these laser lines was 5:4:4:1. As far as we know, these laser lines have never been reported except for 3.01 μm. Some mechanisms for forming a population inversion are initially discussed on the basis of analyzing features of corresponding energy-level structure and experimental phenomena. It is reasonable to name this kind of laser as an M–M transition laser according to the feature of the lasing process. Received: 15 October 2002 / Published online: 9 April 2003 RID="*" ID="*"Corresponding author. Fax: +86-0571/8795-1328, E-mail: pbl66@zju.edu.cn     

Three-dimensional reversible laser micromachining with subnanojoule femtosecond pulses based on two-photon photochromism

Three-dimensional reversible laser micromachining of polymer materials based on two-photon photochromism is demonstrated. Unamplified 60-fs, 0.5-nJ pulses of 790-nm Ti:sapphire laser radiation are used to induce a refractive-index change in a polymethyl methacrylate (PMMA) sample doped with spiropyran molecules through a two-photon absorption process. Waveguides are written in the bulk of spiropyran-doped PMMA samples by scanning these samples with respect to a tightly focused Ti:sapphire laser beam. Laser-induced fluorescence is used for on-line monitoring of the laser-micromachining process. The structures written in photochromic samples can be erased and reconfigured due to the reversibility of the photochromic effect. Received: 23 April 2003 / Published online: 6 June 2003 RID="*" ID="*"Corresponding author. Fax: +7-095/939-51-74, E-mail: zheltikov@top.phys.msu.su     

Intracavity optical parametric oscillator at 1572-nm wavelength pumped by passively Q-switched diode-pumped Nd:YAG laser

An intracavity optical parametric oscillator (IOPO) based on bulk KTP crystal was constructed with a Nd:YAG slab as an active medium pumped by a 300-W diode array and Cr:YAG as a passive Q-switch. A signal pulse of 1.9-mJ energy at 1572-nm wavelength was demonstrated. In the cavity, optimized with respect to single-pulse energy, a five-fold shortening of signal-pulse duration with respect to 1064-nm pump radiation was observed. A twice as large level of signal peak power of 650 kW, compared to the pump laser in the same cavity without the IOPO, was achieved. A conversion efficiency of 44% with respect to the 1064-nm pump beam and 3.8% with respect to diode pump energy was demonstrated. Received: 15 October 2002 / Revised version: 19 February 2003 / Published online: 16 April 2003 RID="*" ID="*"Corresponding author. Fax: +48-22/666-8950, E-mail: wzendzian@wat.edu.pl     

Femtosecond pulse shaping in the mid infrared by difference-frequency mixing

The generation of programmable complex femtosecond pulses in the mid infrared (3–10 μm) with high precision is reported. Designed pulse shapes in the near infrared (1–1.6 μm) are transferred to the mid infrared via difference-frequency mixing with a second infrared pulse spectrally narrowed in a zero-dispersion compressor. In particular, pulse sequences with variable relative phases have been obtained. The control of the pulse properties is achieved purely electronically, allowing for implementation into a feedback loop. Received: 12 December 2003 / Published online: 3 April 2003 RID="*" ID="*"Corresponding author. Fax: +49-89/32905-200, E-mail: mcm@mpq.mpg.de