Size-based analysis of incinerator fly ash using gravitational SPLITT fractionation, sedimentation field-flow fractionation, and inductively coupled plasma-atomic emission spectroscopy

Fly ash has been regarded as hazardous because of its high adsorption of toxic organic and/or inorganic pollutants. Fly ash is also known to have broad distributions of different chemical and physical properties, such as size and density. In this study, fly ash emitted from a solid waste incinerator was pre-fractionated into six sub-populations by use of gravitational SPLITT fractionation (GSF). The GSF fractions were then analyzed by sedimentation field-flow fractionation (SdFFF) and ICP–AES. SdFFF analysis showed the fly ash has a broad size distribution ranging from a few nanometers up to about 50 µm. SdFFF results were confirmed by electron microscopy. Inductively coupled plasma–atomic emission spectroscopy (ICP–AES) analysis of the GSF fractions showed the fly-ash particles contain a variety of inorganic elements including Ca, Si, Mg, Fe, and Pb. The most abundant in fly ash was Ca, followed by Si then Mg. No correlations were found between trace element concentration and particle size.     

Hollow-fiber flow/hyperlayer field-flow fractionation for the size characterization of airborne particle fractions obtained by SPLITT fractionation

Hollow-fiber flow field-flow fractionation (HF FlFFF) was applied for the separation and size characterization of airborne particles which were collected in a municipal area and prefractionated into four different-diameter intervals >5.0, 2.5-5.0, 1.5-2.5, <1.5 microm) by continuous split-flow thin (SPLIIT) fractionation. Experiments demonstrated the possibility of utilizing a hollow-fiber module for the high-performance separation of supramicron-sized airborne particles at steric/hyperlayer operating mode of HF FlFFF. Eluting particles during HF FlFFF separation were collected at short time intervals (approximately 10 s) for the microscopic examination. It showed that particle size and size distributions of all SPLITT fractions of airborne particles can be readily obtained using a calibration and that HF FlFFF can be utilized for the size confirmation of the sorted particle fraction during SPLITT fractionation.     

Pinched inlet gravitational split-flow thin fractionation of airborne particles and analysis of size dependent level of PCDD/Fs

Fine particles in air have a direct influence on human health because they carry toxic chemicals that can be deposited in the human lung when inhaled. Thus, particle size distribution and size dependent level of contamination of the airborne particles are important parameters for the study and assessment of environmental pollution. In this study, gravitational split-flow thin (SPLITT) fractionation (or GSF), a semi-preparative scale separation technique for particles, was applied for the continuous size sorting of airborne particles collected in urban area. About 2.0 g of airborne particles was fractionated into four different size intervals (<1.5, 1.5-2.5, 2.5-5.0, and >5.0 microm), and the collected fractions were examined by electron microscopy for particle size distribution and analyzed for the size dependent levels of polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs). It was found that more than 60% of particles including dissolved matters in weight were smaller than 5.0 microm and they contained more than 86% of the total PCDD/Fs amount in airborne particles.     

Size fractionation of marine sediments by pinched inlet gravitational split-flow thin fractionation and the study of size dependent PCDD/Fs concentrations from different bay areas

Pinched inlet gravitational split-flow thin fractionation (PI-GSF) has been applied to the continuous size fractionation of marine sediments in order to study the difference in sediment size distribution and the concentration of PCDD/Fs contained in different particle sizes. A PI-GSF channel, known to improve the separation efficiency by reducing the sample inlet thickness, was utilized to fractionate sediments collected from three different bay areas (Geoje, Ulsan, and Pohang) in Korea into 5 different sub-populations (<2.0, 2.0-5.0, 5.0-10, 10-20, 20-63 microm in diameter). The sorted sediment fractions from PI-GSF were examined using electron microscopy to obtain size distribution and the results showed a variation in particle size distribution between bay areas. When the collected particle fractions were examined for size dependent levels of PCDD/Fs, the concentrations of total PCDD/Fs were shown to be much greater for samples collected close to heavy industry complexes than sediments from bay areas without major industry.     

Assessment of the distribution of pesticides on soil particle fractions in simulated irrigation run-off using centrifugal SPLITT fractionation and ELISA

This study was designed to measure the distribution of pesticides within the mobile phase of simulated irrigation run-off water, using centrifugal split-flow thin-channel (SPLITT) fractionation, a novel technique providing a gentle separation of natural sediment and suspended particles. Particular attention is paid to the extraction of pesticide residues for enzyme-linked immunosorbent assay (ELISA) analysis; ELISA was used because of the limited sample size.Centrifugal SPLITT fractionation combined laminar flow hydrodynamics and centrifugal sedimentation to obtain a continuous binary separation of suspended particles. The non-destructive technique allowed an accurate separation of particles into fractions with divisions at 0.5, 2 and 10 μm, with those above 25 μm being performed by wet sieving. ELISA was used to analyse the concentration of endosulfan and diuron for each fraction generated by the SPLITT technique.This data can be used to determine the role that particulate fines and colloidal fractions play in the transport of bound organic pollutants within the environment and to examine prospects for remediation on farms.     

Coupling gravitational and flow field-flow fractionation, and size-distribution analysis of whole yeast cells

This work continues the project on field-flow fractionation characterisation of whole wine-making yeast cells reported in previous papers. When yeast cells are fractionated by gravitational field-flow fractionation and cell sizing of the collected fractions is achieved by the electrosensing zone technique (Coulter counter), it is shown that yeast cell retention depends on differences between physical indexes of yeast cells other than size. Scanning electron microscopy on collected fractions actually shows co-elution of yeast cells of different size and shape. Otherwise, the observed agreement between the particle size distribution analysis obtained by means of the Coulter counter and by flow field-flow fractionation, which employs a second mobile phase flow as applied field instead of Earths gravity, indicates that yeast cell density can play a major role in the gravitational field-flow fractionation retention mechanism of yeast cells, in which flow field-flow fractionation retention is independent of particle density. Flow field-flow fractionation is then coupled off-line to gravitational field-flow fractionation for more accurate characterisation of the doubly-fractionated cells. Coupling gravitational and flow field-flow fractionation eventually furnishes more information on the multipolydispersity indexes of yeast cells, in particular on their shape and density polydispersity.     

SPLITT Cell Analytical Separation of Silica Particles. Non-Specific Crossover Effects: Does the Shear-Induced Diffusion Play a Role?

The gravitational split-flow lateral transport thin fractionation is known to be a fast, simple, theoretically tractable and tunable tool for the binary separation of molecular or particulate samples into different dimensional fractions. This fractionation is performed in a so-called SPLITT cell and is due to the combined effect of the gravitational force field and the flow rates inside the separation channel. It is known that separation performance is strongly dependent on the flow rate conditions and feed flow concentration, however, to date, few studies have been conducted to investigate the effect non-specific crossover has on separation. The aim of this work is to establish whether diffusive processes stemming from hydrodynamic effects contribute in any way to the quality of separation. A silica sample of known granule size distribution was chosen for this study which has environmental applications.     

Analytical SPLITT cell fractionation: Linearity and resolution study

In this paper the analytical SPLITT (split flow thin cell) procedure is used to characterize the percentage composition of micronic polydisperse particulate samples at a given cut‐off size. The linearity and resolution of the separation method have been tested using specifically prepared starch samples, in order to compare the analytical process with two continuous (preparative) SPLITT procedures. Linearity has been checked by injecting a series of suspensions (at different concentrations) under five different flow rate conditions. Retrieval factors F were evaluated to verify the relative amount of sample exiting the cell outlets. The effective resolution has been assessed by inspecting the SPLITT fractions with an optical microscope, counting the granules, and evaluating the percentage of granules of expected size. It has been found that the resolution is very good (around 90%) and independent of sample distribution. It is seen from the comparison that in the analytical SPLITT mode sample resolution is usually around 85–90% and it is significantly better than that of the continuous SPLITT modes, thus making the analytical mode valuable in characterizing polydisperse samples. The method was tested for the characterization of a commercial starch sample.     

Continuous split-flow thin cell and gravitational field-flow fractionation of wheat starch particles

The combined employment of the SPLITT (split-flow thin) cell--a relatively new system for fast, continuous binary separation--and of gravitational field-flow fractionation (GrFFF)--a fractionation technique suitable for micron particle size distribution determination--was investigated for starch separation and characterization. Emphasis is placed on the main advantages of both techniques: operating under gentle earth gravity field, low cost and ease of maintenance. The reproducibility of GrFFF is demonstrated. Both the SPLITT separation and GrFFF fractionation results were checked by optical microscopy. Application examples of typical starch fractionation experiments are reported and discussed.     

Dimensional and elemental characterization of suspended particulate matter in natural waters: quantitative aspects in the integrated ultrafiltration, splitt-flow thin cell and inductively coupled plasma–atomic emission spectrometry approach

The present study investigates the quantitative aspects of an analytical procedure for the trace element characterization of suspended particulate matter (SPM) in natural waters. The procedure consists of the following steps: (1) ultrafiltration (UF) concentration; (2) splitt-flow thin (SPLITT) cell fractionation (SF) into different micronic–submicronic dimensional ranges; and (3) inductively coupled plasma–atomic emission spectrometry (ICP–AES) elemental determination on both the separated fractions and the bulk phase. One specific feature of the UF/SF steps is that they are gentle and thus preserve the complexity of the colloidal features of SPM samples as far as possible. The investigation was performed on a real SPM sample (Po River, Italy). Two SF modes were considered: the so called conventional SPLITT fractionation (CSF) mode and the full feed depletion SPLITT fractionation (FFDSF) mode. These differ in terms of resolution, time (both better in CSF as compared to FFDSF) and operating mode (FFDSF does not require a diluting carrier). Quantitative aspects of the UF step recovery and of the CSF and FFDSF modes were investigated in terms of total mass balance proving that only the FFDSF mode is currently satisfactory for quantitative purposes. Mass balance versus the following elements: Cd, Cr, Cu, Mn, Ni and Pb, was performed using ICP–AES over the 0.2–1.5 and 1.5–20 μm FFDSF SPM fractions, proving that the analytical procedure based on UF/FFDSF/ICP–AES is consistent and useful in the investigation of trace element distribution in different SPM dimensional ranges versus that of the bulk phase. The relevance of aggregation–solubility equilibria concerning colloids of SPM phase is emphasized and further improvement of the procedure is discussed.     

Increased size‐sorting performance in gravitational SPLITT by using a pinched sample inlet design

Split‐flow thin fractionation is a continuous, flow‐assisted separation technique for sorting macromolecules and particulate matter on a preparative scale. On reducing the thickness of the sample inlet conduit of a gravitational split‐flow thin fractionation channel, size‐sorting performance is found to increase since particles that are continuously fed into the channel can be more rapidly compressed toward the upper wall of the channel. Experiments are carried out by measuring the number percentage of particles eluted at each outlet as a function of different thickness values of the sample inlet conduit. The effects that the total thickness of the gravitational split‐flow thin fractionation channel and the sample feed concentration have on the size‐fractionation performance are examined with the goal of determining the best pinched sample inlet, gravitational split‐flow thin fractionation channel design.     

Tandem hollow-fiber flow field-flow fractionation

Reinjection of one ore more collected fractions of eluted samples is recognized as a useful procedure in analytical separation techniques, among which field-flow fractionation (FFF), to improve the actual separation of complex samples. Hollow-fiber flow FFF (HF5) is a micro-channel subset of flow FFF (F4), which has recently reached a performance comparable to that of standard, flat-channel F4. To further improve HF5 of complex protein samples, we present a new device and method for in-line, reinjection HF5 that we call tandem HF5 (HF5/HF5). HF5 is ideally suited for tandem operation because (1) small channel volume and low operation flow rates allow reducing dilution and volume of the collected fractions, and (2) the relaxation/focusing step that takes place between the 1st and 2nd run (refocusing) allows reestablishing the volume and concentration of the sample plug before the 2nd elution. HF5/HF5 proves particularly effective in the case of oligomeric proteins since it allows collecting and reinjecting the bands that correspond to each separated oligomeric form. This provides information on the dynamic equilibria between the different oligomers. For HF5/HF5 operations, a modified, prototype HF5 instrumentation is presented which includes a "trap" constituted of a four-port, two-way valve positioned downstream the UV detector and a collection loop. The effect of refocusing conditions on HF5/HF5 performance is investigated by varying refocusing time. With a complex protein samples such as blood serum, HF5/HF5 can improve detectability of the low abundance components since overloading effects due to high-abundance components are reduced. This is shown for serum lipoproteins: while after the 1st run high density lipoproteins (HDLs) are not separated from high-abundance serum proteins, after the 2nd run it is shown possible to separate the HDL subclasses.     

Dielectrophoretic field‐flow fractionation of electroporated cells

We describe the development and testing of a setup that allows for DEP field‐flow fractionation (DEP‐FFF) of irreversibly electroporated, reversibly electroporated, and nonelectroporated cells based on their different polarizabilities. We first optimized the channel and electrode dimensions, flow rate, and electric field parameters for efficient DEP‐FFF separation of moderately heat‐treated CHO cells (50°C for 15 min) from untreated ones, with the former used as a uniform and stable model of electroporated cells. We then used CHO cells exposed to electric field pulses with amplitudes from 1200 to 2800 V/cm, yielding six groups containing various fractions of nonporated, reversibly porated, and irreversibly porated cells, testing their fractionation in the chamber. DEP‐FFF at 65 kHz resulted in distinctive flow rates for nonporated and each of the porated cell groups. At lower frequencies, the efficiency of fractionation deteriorated, while at higher frequencies the separation of individual elution profiles was further improved, but at the cost of cell flow rate slowdown in all the cell groups, implying undesired transition from negative into positive DEP, where the cells are pulled toward the electrodes. Our results demonstrate that fractionation of irreversibly electroporated, reversibly electroporated, and nonelectroporated cells is feasible at a properly selected frequency.     

Separation of carbon nanotubes by frit inlet asymmetrical flow field-flow fractionation

Flow field-flow fractionation (flow FFF), a separation technique for particles and macromolecules, has been used to separate carbon nanotubes (CNT). The carbon nanotube ropes that were purified from a raw carbon nanotube mixture by acidic reflux followed by cross-flow filtration using a hollow fiber module were cut into shorter lengths by sonication under a concentrated acid mixture. The cut carbon nanotubes were separated by using a modified flow FFF channel system, frit inlet asymmetrical flow FFF (FI AFIFFF) channel, which was useful in the continuous flow operation during injection and separation. Carbon nanotubes, before and after the cutting process, were clearly distinguished by their retention profiles. The narrow volume fractions of CNT collected during flow FFF runs were confirmed by field emission scanning electron microscopy and Raman spectroscopy. Experimentally, it was found that retention of carbon nanotubes in flow FFF was dependent on the use of surfactant for CNT dispersion and for the carrier solution in flow FFF. In this work, the use of flow FFF for the size differentiation of carbon nanotubes in the process of preparation or purification was demonstrated.     

Methods for continuous flow fractionation of microparticles: Outlooks and fields of application

The development of new methods for fractionating particles of a different nature is becoming more important in solving some scientific and technological problems. This paper presents a brief review in the theory and practice of the most common techniques for microparticle fractionation (0.1–100 μm). These are dry and wet sieving, elutriation, sequential filtration, split-flow thin fractionation (SPLITT system), field-flow fractionation (FFF), membrane filtration, and capillary electrophoresis. Special attention is paid to the FFF technique, which offers a unique potential for the separation of different materials, from biopolymers and microorganisms to colloidal and solid particles, and the estimation of their physical properties. An alternative version of sedimentation FFF is described, namely, the fractionation of microparticles in rotating coiled columns. The main advantages and limitations of the methods are revealed and their outlooks and fields of applications are envisaged.     

Quantitative SPLITT fractionation of lagoon sediments

In this work, SPLITT Fractionation (split flow thin cell) is used to sort hydrodynamically sedimented particles coming from the Sacca di Goro, a lagoon-like system close to the Po River delta (Italy). First the possibility of performing quantitative mass separations with a SPLITT cell apparatus was checked on a standard silica sample of known particle size distribution (PSD). Environmental sediment samples and relative SPLITT sub-fractions were subject to Inductive Coupled Plasma--Atomic Emission Spectroscopy (ICP-AES) characterization for the following elements: Al, Fe, Cd, Cr, Cu, Ni, Mn, Pb and Zn. The distribution of these metals by particle size fractions has been investigated. The accuracy of the entire separation procedure has been also evaluated.     

Analysis of complex polymers by multidetector field-flow fractionation

Field-flow fractionation (FFF) is a powerful alternative to column-based polymer fractionation methods such as size-exclusion chromatography (SEC) or interaction chromatography (IC). The most common polymer fractionation method, SEC, has its limitations when polymers with very high molar masses or complex structures must be analysed. Another limitation of all column-based methods is that the samples must be filtered before analysis and shear degradation of large macromolecules may be caused by the stationary phase and/or the column frits. Finally, the separation of very polar polymers may be a challenge because such polymers interact very strongly with the stationary phase, causing irreversible adsorption or other negative effects. This article reviews the latest developments in field-flow fractionation of complex polymers. It is demonstrated that some of the limitations of column-based chromatography can be overcome by FFF. When appropriate, results from column-based fractionations are compared with those from FFF fractionations to highlight the specific merits and challenges of each method. In addition to the fractionations themselves, various detector setups are discussed to show that different polymer distributions require different experimental procedures. Examples are given of the analysis of molar mass distribution, chemical composition, and microstructure. Advanced detector combinations are discussed, most prominently the very recently developed coupling to ¹H NMR. Finally, analysis of polymer nanocomposites by asymmetric flow field-flow fractionation (AF4)–FTIR is presented.

General theory for flow optimisation of split-flow thin fractionation

Recently, magnetic split-flow thin (SPLITT) fractionation has been developed to separate macromolecules, colloids, cells and particles. However, the previous theory, developed for an infinitely long channel, needs to be improved to consider the flow transit regimes at both inlet and outlet. In this paper, we describe a new approach to optimising flow-rates for particle separation which considers the effect of flow transit region. Surprisingly, the critical particle migration velocities derived by the present theory are identical to the previous simplified theory. Therefore, the previous simplified theory may have wider application than might have been expected. As a test of our theory, a numerical simulation based on solving Navier-Stokes equations has also been carried out for a magnetic SPLITT device. The trajectory of a particle with the critical migration velocity is exactly as expected by our theory. Following experimental validation, this work will facilitate the design of new SPLITT fractionation systems with smaller aspect ratio.     

Experimental study on the retention of silica particles in gravitational field-flow fractionation effects of the mobile phase composition

Effects of mobile phase composition can play an effective role in modulating the retention of particles in gravitational field-flow fractionation (GFFF), the simplest and cheapest among field-flow fractionation (FFF) techniques. In the framework of an optimized procedure for the GFFF characterization of particulate systems, an experimental approach to the effects of the mobile phase composition on the retention of silica particles retention is presented. The role of the ionic strength and the presence of surfactant are emphasized, with special regards to the shape of the particles. Moreover, the first experimental evidence of potential-barrier GFFF is reported.     

Size-based speciation of iron in clay mineral particles by gravitational field-flow fractionation with electrothermal atomic absorption spectrometry

Gravitational field-flow fractionation (FFF) coupled to UV and ETAAS detectors has been tested for micron-size particles in the range of 5–20 μm using three Fe-rich clay samples. The iron content estimated after aqua regia extraction was about 20–40 mg kg⁻¹. The ETAAS analysis was performed both off-line from collected fractions and in an online continuous sampling mode using a specially designed flow through vial placed in the autosampler of the ETAAS. Comparison of the direct injection method with total analysis after aqua regia digestion shows that slurry injection of the dilute samples in the gravitational field-flow fractionation (GrFFF) effluent is quite efficient in these samples. In the majority of cases, more than 90% recovery was obtained for the slurry injection method. Fe mass-based particle size distributions and Fe concentration versus particle diameter plots can be generated using certain assumptions. This provides detailed information on size-based speciation of particulate samples. Generally, the Fe concentrations in the particles decreased slightly with an increase in particle size as is often found for soil and sediment samples.