含氧化镧的甲烷氧化偶联催化剂的一些特性

利用ＤＴＡ、ＴＰＤ－ＭＳ、ＸＲＤ、ＴＰＲ及ＴＰＳＲ－ＭＳ等手段对Ｌａ＿２Ｏ＿３和含Ｌａ＿２Ｏ＿３的甲烷氧化偶联催化剂进行了研究。实验发现含Ｌａ＿２Ｏ＿３的催化剂的一个特点是其容易吸水，此时，催化剂中除含Ｌａ＿２Ｏ＿３外，还有Ｌａ（ＯＨ）＿３及Ｌａ＿２Ｏ＿３ＣＯ＿２存在。ＴＰＲ及ＴＰＳＲ结果表明了催化剂的起始氢气还原温度与纯甲烷的程序升温反应开始温度的一致性，这说明催化剂的晶格氧参与了甲烷的活化过程。不同的氧化物由于其晶格氧的活性不同，因而其活化甲烷的温度不同。Ｌａ＿２Ｏ＿３中的晶格氧非常活泼，它在７３０℃时即可以与甲烷或与Ｈ＿２反应而本身被还原。甲烷和氧气共进料时的程序升温反应（ＴＰＳＲ－ＭＳ）表明甲烷氧化偶联反应中Ｃ＿２烃的选择性有一最佳温度范围。     

两相体系中钌膦配合物催化4—苯基—3—丁烯—2—酮加氢反应的研究

研究了水和有机物组成的两相催化体系中,由ＲｕＣｌ３－ＴＰＰＴＳ（ＴＰＰＴＳ：Ｐ（ｍ－Ｃ６Ｈ４ＳＯ３Ｎａ）３）原位反应生成的催化活性物种对４－苯基－３－丁烯－２－酮（又名苄叉丙酮）的催化加氢反应．考察了钌浓度（１．０×１０－３～６．０×１０－３ｍｏｌ／Ｌ）、氢压（１．０～６．０ＭＰａ）、反应温度（３０～７０℃）、配体浓度（１．２～７．２×１０－２ｍｏｌ／Ｌ）、阳离子表面活性剂（ＣＴＡＢ：十六烷基三甲基溴化铵）及反应时间等对加氢反应活性和选择性的影响,并与以配合物ＲｕＣｌ２（ＴＰＰＴＳ）３为催化剂前体生成的催化活性物种对加氢反应的活性及选择性进行了比较．结果表明,分别由配合物ＲｕＣｌ２（ＴＰＰＴＳ）３及ＲｕＣｌ３－ＴＰＰＴＳ原位反应生成的催化活性物种,都只催化４－苯基－３－丁烯－２－酮的Ｃ＝Ｃ键选择加氢．由配合物ＲｕＣｌ２（ＴＰＰＴＳ）３形成的催化体系的加氢活性及选择性均优于ＲｕＣｌ３－ＴＰＰＴＳ原位反应生成的催化活性物种．阳离子表面活性剂的加入,使加氢反应活性下降,选择性略有提高     

胺固化端环氧基二硅氧烷动力学及性能研究

合成了１，３－二甲基－１，３－二乙基－１，３－双［３－（２，３－环氧丙氧基）丙基］二硅氧烷（ＴＥＤＳ）．对其与二正丁胺的模型反应、与ＤＤＭ（４，４’－二氨基二苯基甲烷）的固化反应劝力学研究表明，反应对ＴＥＤＳ为一级反应．ＴＥＤＳ改性环氧Ｅ—５１体系的动态力学性能、冲击性能和形态结构的研究表明，随改性体系中ＴＥＤＳ含量的增加，体系的玻璃化温度是线性下降、冲击强度增大、冲击试样的断裂面渐渐显现出韧性断裂的特征．     

两相催化体系中α，β－不饱和醛的选择性加氢反应研究Ⅰ．水溶性钌－膦配合物催化肉桂醛的加氢性能

本文研究了两种水溶性钌－膦配合物ＲｕＣｌ_２（ＴＰＰＴＳ）_３和Ｒｕｃｌ_２（ＣＯ）_２（ＴＰＰＴＳ）_２［ＴＰＰＴＳ为：Ｐ（ｍ－Ｃ_６Ｈ_４ＳＯ_３Ｎａ）_３］的合成，在水相和有机相组成的两相催化体系中，考察了它们衍生出的活性物种和以ＲｕＣｌ３－ＴＰＰＴＳ原位合成的活性物种对肉桂醛的选择加氢性能，并对反应温度（２０—８０℃），氢压（２—６ＭＰａ），催化剂浓度（１．１２×１０~（－３）～４．５０×１０~（－３）ｍｏｌ／Ｌ），配体ＴＰＰＴＳ浓度（９．０×１０~（－３）～５．４×１０~（－２）ｍｏｌ／Ｌ），表面活性剂浓度和反应时间的变化对选择加氢反应的影响进行了详细研究。实验结果表明，ＲｕＣｌ_３－ＴＰＰＴＳ原位合成配合物的催化加氢活性最高，而在金属Ｒｕ上羰基的配位将使加氢活性降低，表面活性剂ＣＴＡＢ是有效的促进剂，它的加入可大大提高加氢活性，选择适当的ＣＴＡＢ浓度，在反应结束后水相与有机相分层迅速，有利于Ｒｕ催化剂的分离，在所考察的反应条件下，肉桂醛选择加氢生成肉桂醇的转化率大于８０％，选择性达９６％以上。     

稠杂环化合物的研究（XV）：6—取代—3—（1H—苯并三唑—1—亚甲基）…

研究了３－（１Ｈ－苯并三唑－１－亚甲基）－４－氨基－５－巯基－１，２，４－三唑与取代苯甲酸在三氯氧磷催化下的反应，制得１０种新的３－（１Ｈ－苯并三唑－１－亚甲基）－１，２，４－三唑并［３，４－ｂ］－１，３，４噻二唑，通过元素分析，ＩＲ、＾１ＨＮＭＲ和ＭＳ确证了它们的结构并讨论了其波谱性质。     

稠杂环化合物的研究（XV）──6－取代－3－（1H－苯并三唑－1－亚甲基）－1，2，4－三唑并［3，4－b］－1，3，4－噻二唑的合成

研究了３－（１Ｈ－苯并三唑－１－亚甲基）－４－氨基－５－巯基－１，２，４－三唑与取代苯甲酸在三氯氧磷催化下的反应，制得１０种新的３－（１Ｈ－苯并三唑－１－亚甲基）－１，２，４．三唑并［３，４－ｂ］－１，３，４－噻二唑，通过元素分析、ＩＲ、￣１ＮＭＲ和ＭＳ确证了它们的结构并讨论了其波谱性质。     

甲烷氧化偶联催化反应的特征

应用程序升温反应（ＴＰＲ）及质谱分析表征了ＣａＯ，Ｓｍ２Ｏ３，０．５－１０％Ｓｍ／ＣａＯ催化剂上的甲烷氧化偶联反应特性。谱图分析表明，在４００－１０００℃范围内，甲烷氧化偶联反应产物的变化呈现三个反应温度区域：（１）完全氧化区，反应主要为ＣＨ３·在催化剂表面完全氧化形成ＣＯｘ和Ｈ２：（２）偶联区，主要为ＣＨ３·的氧化和偶联竞争反应，Ｈ２谱线出现明显的低温峰；（３）氧耗尽区，反应为高温气相反应，产物     

2,3—二甲基吡嗪合成工艺的改进

报道了以丁二酮和乙二胺为原料，对液相合成２，３－二甲基吡嗪的方法进行了改进，考察了反应温度，溶剂用量和脱氢剂等对反应影响，确定了合成２，３－二甲基吡嗪的优化条件为，丁二酮：乙二胺（摩尔比）＝１：１．０５；丁二酮：溶剂无水乙醇（体积比）＝１：１０，缩合反应温度：－５℃，时间：１ｈ，脱氢剂：ＤＨＫＭ－１２，脱氢温度：８０～８５℃，时间：１ｈ２，３－二甲基吡嗪的产率按投料丁二酮设计达６５％。     

含固氮酶钼微环境结构单元O_3MoS_3的Mo－S，Mo－Fe－S化合物的研究

研究了含固氮酶钼微环境Ｏ_３ＭｏＳ_３结构单元四个系列化合物［Ｍｏ（Ｓ，Ｏ－Ｃ_６Ｈ_４－１，２］~－（Ｍ）［Ｍｏ_２（ＣＯ）_３（Ｓ，Ｏ－Ｃ_６Ｈ_４－１，２）_３］~（２－）（Ｄ），［Ｍｏ_３（ＣＯ）_７（Ｓ，Ｏ－Ｃ_６Ｈ_４－１，２）_３］~（２－）（Ｔ），和［Ｍｏ_２Ｆｅ（ＣＯ）_４（Ｓ，Ｏ－Ｃ_６Ｈ_４－１，２）_３Ｃｌ_２］~（２－）（Ｔ_ｆ）的合成化学与结构化学，并通过Ｘ－射线光电子能谱，红外光谱和电化学环伏安研究，深入探讨了它们的混合价，电子迁移和电化学行为，也讨论了有趣的Ｏ_３ＭｏＳ_３结构单元。     

水溶性铑—膦配合物催化长链烯烃氢甲酰化反应研究—反应条件的影响

本文研究了两相催化体系中，在ＣＴＡＢ（Ｃ１６Ｈ３３ＮＭｅ３Ｂｒ）存在下，水溶性铑－膦配合物ＲｈＣｌ（ＣＯ）（ＴＰＰＴＳ）２对１－己烯氢甲酰化反应的催化性能，详细考察了反应温度、压力、膦／铑比等对催化活性的影响。结果表明，在１．０ＭＰａ恒压下，反应温度１００℃，膦／铑摩尔比为１６，Ｈ２：ＣＯ＝１：１的条件下，１－己烯氢甲酰化的转化频率（ＴＯＦ）可达到３９．８ｍｉｎ＾－１。在此反应条件下，有机相和水相     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。