Co掺杂(ZnO)12团簇的结构和磁性质

采用第一性原理密度泛函理论系统地研究Co原子单掺杂和双掺杂(ZnO)₁₂团簇的结构和磁性质.考虑三种掺杂方式:替代掺杂,外掺杂和内掺杂.首先比较各种掺杂团簇的稳定性.结果表明,不管是单掺杂还是双掺杂,外掺杂团簇都是最稳定结构.在结构优化的基础上,对掺杂的(ZnO)₁₂团簇进行磁性计算.发现团簇磁矩主要来自Co-3d态的贡献,4s和4p态也贡献了一小部分磁矩.由于轨道杂化,相邻的Zn和O原子也产生少量自旋.Co原子之间的磁性耦合由直接的Co-Co反铁磁耦合和Co和O原子之间通过p-d杂化产生的铁磁耦合这两种相互作用的竞争决定.研究发现外双掺杂团簇存在铁磁耦合,在纳米量子器件有潜在的应用价值.     

水热法制备Co掺杂ZnO纳米棒及其光学性能

采用水热法在石英衬底上以Zn(CH3COO)2.2H2O和Co(NO3)2.6H2O水溶液为源溶液,以C6H12N4(HMT)溶液作为催化剂,在较低温度下制备了Co掺杂的ZnO纳米棒。采用X射线衍射(XRD)和扫描电子显微镜(SEM)对所生长ZnO纳米棒的晶体结构和表面形貌进行了表征,考察了Co掺杂对ZnO纳米棒微观结构和对发光性能影响的机制。结果表明:Co掺杂的ZnO纳米棒呈六方纤锌矿结构,具有沿(002)面择优生长特性,Co掺杂使ZnO纳米棒的直径变细;同时室温光致发光(PL)谱检测显示Co掺杂ZnO纳米棒具有很强的近带边紫外发光峰,而与深能级相关的缺陷发光峰则很弱。本研究采用水热法在石英衬底上于较低温度下生长出了具有较高光学质量的Co掺杂ZnO纳米棒。     

H掺杂对ZnCoO稀磁半导体薄膜结构及磁性能的影响

利用磁控溅射法,采用亚分子分层掺杂技术交替溅射Co靶和ZnO靶,在Si衬底上制备了不同氢氩流量比的H:ZCO薄膜样品,研究了氢氩流量比对薄膜结构特性和磁学性能的影响。所制备的薄膜样品具有c轴择优取向。由于H对表面和界面处悬挂键的钝化作用,随H₂流量比的增加,薄膜的择优取向变差。磁性测量结果显示,薄膜样品的铁磁性随着氢氩流量比的增大而增强。XPS结果表明,随着H含量的增大,金属态Co团簇的相对含量逐渐增加,而氧化态Co离子的相对含量逐渐减小。H:ZCO样品中的铁磁性可能来源于Co金属团簇,H的掺入促使ZnO中的Co离子还原成Co金属团簇,从而增强了薄膜样品的室温铁磁性。     

Co掺杂ZnTe团簇结构和磁性质

本文采用第一性原理密度泛函理论系统的研究了Co原子单掺杂和双掺杂(ZnTe)_(12)团簇的结构和磁性质.考虑了两种掺杂方式:替代掺杂和间隙掺杂.不管是单掺杂还是双掺杂,间隙掺杂团簇都是最稳定结构.Co掺杂团簇的磁性依赖于Co原子周围环境.最重要的是,我们指出替代双掺杂团簇是铁磁耦合,在纳米量子器件领域有潜在的应用价值.     

Al和Sb共掺对ZnO有序阵列薄膜的结构和光学性能的影响

采用水热合成法在预先生长的ZnO种子层的玻璃衬底上制备出Al和Sb共掺ZnO纳米棒有序阵列薄膜. 通过X射线衍射、扫描电镜、透射电镜和选区电子衍射分析表明:所制备的薄膜由垂直于ZnO种子层的纳米棒组成, 呈单晶六角纤锌矿ZnO结构, 且沿[001]方向择优生长, 纳米棒的平均直径和长度分别为27.8 nm和1.02 μm. Al和Sb共掺ZnO纳米棒有序阵列薄膜的拉曼散射分析表明:相对于未掺杂ZnO薄膜的拉曼振动峰(580 cm^-1), Al和Sb共掺ZnO阵列薄膜的E₁(LO)振动模式存在拉曼位移. 当Al和Sb的掺杂量为3.0at%,4.0at%,5.0at%,6.0at%时, Al和Sb共掺ZnO阵列薄膜的拉曼振动峰的位移量分别为3,10,14,12 cm^-1. E₁ (LO) 振动模式位移是由Al和Sb掺杂ZnO产生的缺陷引起的. 室温光致发光结果表明:掺杂Al和Sb后, ZnO薄膜在545 nm处的发光强度减小,在414 nm处的发光强度增加. 这是由于掺杂Al和Sb后, ZnO薄膜中Zn_i缺陷增加, O_i缺陷减少引起的. 关键词： Al和Sb共掺ZnO薄膜 纳米棒有序阵列 结构表征 拉曼散射     

离子注入Zn的Si(001)基片热氧化制备纳米ZnO团簇及其生长行为研究

采用离子注入技术将Zn离子注入Si（001）基片,并在大气环境下加热氧化制备了ZnO纳米团簇.利用电子探针、薄膜X射线衍射仪、原子力显微镜和透射电子显微镜,对注入和热氧化后的薄膜成分、表面形貌和微观结构进行表征,探讨了热氧化温度以及注入剂量对纳米ZnO团簇的成核过程及生长行为的影响.结果表明,Zn离子注入到Si基片表面后形成了Zn纳米团簇,热氧化过程中Zn离子向表面扩散,在表面SiO₂非晶层和Si基片多晶区的界面处形成纳米团簇.热氧化温度是影响ZnO纳米团簇结晶质量的一个重要参数.随着热氧化温度的升高,金属Zn的衍射峰强度逐渐变弱并消失,而ZnO的（101）衍射峰强度逐渐增强.当热氧化温度高于800 ℃以后,ZnO与SiO₂之间开始发生化学反应形成Zn₂SiO₄. 关键词： ZnO纳米团簇 离子注入 微观结构 形貌分析     

Fe,Co共掺杂ZnO薄膜结构及发光特性研究

采用溶胶凝胶法在玻璃衬底上制备了Fe,Co共掺Zn0.9FexCo0.1-xO(x=0,0.03,0.05,0.07)系列薄膜.通过扫描电镜(SEM)、X射线衍射(XRD)、X射线光电子谱(XPS)和光致发光(PL)谱对薄膜样品的表面形貌、晶体结构、成分和光学性能进行了研究.XRD结果表明所有ZnO薄膜样品都呈六方纤锌矿结构,在样品中没有观察到与Fe和Co相关的团簇,氧化物及其他杂相的衍射峰,表明共掺杂改善了Fe或Co在ZnO的分散性.XPS测试结果揭示样品中Co离子的价态为+2价;Fe离子的价态为+2价和+3价共存,但Fe相对浓度的增大导致Fe3+含量增加.所有样品的室温光致发光谱(PL)均观察到紫外发光峰和蓝光双峰,其中Fe,Co共掺ZnO薄膜的紫外发光峰较本征ZnO出现蓝移,蓝光双峰峰位没有变化,但发光强度有所减弱;而掺杂ZnO薄膜的绿光发光峰几乎消失.最后,结合微结构和成分分析对薄膜样品的发光机理进行了讨论.     

Co掺杂碲化锌团簇结构和磁性质

本文采用第一性原理密度泛函理论系统的研究了Co原子单掺杂和双掺杂(ZnTe)12团簇的结构和磁性质。考虑了两种掺杂方式：替代掺杂和间隙掺杂。不管是单掺杂还是双掺杂,间隙掺杂团簇都是最稳定结构。Co掺杂团簇的磁性依赖于Co原子周围环境。最重要的是,我们指出替代双掺杂团簇是铁磁耦合,在纳米量子器件领域有潜在的应用价值。     

Co掺杂碲化锌团簇结构和磁性质

本文采用第一性原理密度泛函理论系统的研究了Co原子单掺杂和双掺杂(ZnTe)12团簇的结构和磁性质。考虑了两种掺杂方式：替代掺杂和间隙掺杂。不管是单掺杂还是双掺杂,间隙掺杂团簇都是最稳定结构。Co掺杂团簇的磁性依赖于Co原子周围环境。最重要的是,我们指出替代双掺杂团簇是铁磁耦合,在纳米量子器件领域有潜在的应用价值。     

退火氛围对掺杂ZnO薄膜磁性的影响

采用直流磁控反应共溅法制备了非磁性元素Al和磁性元素Co掺杂的ZnO薄膜, 样品原位真空退火后再空气退火处理. 利用X射线衍射仪(XRD) 和物理性能测量仪(PPMS) 对薄膜的结构和磁性进行了表征. XRD和PPMS结果表明, 不同的退火氛围对掺杂薄膜的结构和磁性有着很大的影响. 真空退火的Al掺杂ZnO薄膜没有观察到铁磁性, 而空气退火的样品却显示出明显的室温铁磁性, 铁磁性的来源与空气退火后导致Al和ZnO基体间电荷转移增强有关. 而对于Co掺杂ZnO薄膜, 真空退火后再空气退火, 室温铁磁性明显减弱. 其磁性变化与Co离子和ZnO基体间电荷转移导致磁性增强和间隙Co原子被氧化导致磁性减弱有关.     

Co掺杂ZnO纳米棒的共振拉曼光谱和发光特性

采用X射线衍射(XRD)和透射电子显微镜(TEM)手段对微乳液法合成的Zn0.9Co0.1O纳米棒进行了表征.通过室温下的共振拉曼光谱和光致发光光谱手段,研究了所合成纳米材料的共振拉曼光谱和发光特性,并与体相ZnO的研究结果对比,发现合成的材料具有四阶声子紫外共振拉曼散射,而体相材料只有两阶,并观察到在紫外和可见区域所...     

Observation of quantum confinement in ZnO nanorods fabricated using a two-temperature growth method

We observed a quantum confinement effect in vertically well-aligned ultrafine ZnO nanorods using polarized excitation photoluminescence measurements. Room-temperature and low-temperature photoluminescence spectra revealed that free excitons were confined in the nanorods. The magnitude of the energy shift due to the quantum confinement in the ultrafine ZnO nanorods was 6 meV at room temperature, which corresponded to the luminescence from ZnO nanorods 12.8 nm in diameter. The diameter estimated from the spectra was comparable to the value measured from SEM images.     

CdS quantum dot-sensitized ZnO nanorod-based photoelectrochemical solar cells

ZnO nanorods have been grown using ZnO seed layer onto ITO-coated glass substrates. CdS quantum dots have been deposited onto ZnO nanorods using simple precursors by chemical method and the assembly of CdS quantum dots with ZnO nanorod has been used as photo-electrode in quantum dot-sensitized solar cells. X-ray diffraction results show that ZnO seed layer, ZnO nanorods, and CdS quantum dot-sensitized ZnO nanorods exhibit hexagonal structure. The particle size of CdS nanoparticle is 5 nm. The surface morphology studied using scanning electron microscope shows that the top surface of the vertically aligned ZnO nanorods is fully covered by CdS quantum dots. The ZnO nanorods have diameter ranging from 100 to 200 nm. The absorption spectra reveal that the absorption edge of CdS quantum dot-sensitized ZnO nanorods shift toward longer wavelength side when compared to the absorption edge of ZnO. The efficiency of the fabricated CdS quantum dot-sensitized ZnO nanorod-based solar cell is 0.69% and is the best efficiency reported so far for this type of solar cells.     

Photoluminescence and field emission of 1D ZnO nanorods fabricated by thermal evaporation

Four kinds of new one-dimensional nanostructures, celery-shaped nanorods, needle-shaped nanorods, twist fold-shaped nanorods, and awl-shaped nanorods of ZnO, have been grown on single silicon substrates by an Au catalyst assisted thermal evaporation of ZnO and active carbon powders. The morphology and structure of the prepared nanorods are determined on the basis of field-emission scanning electron microscopy (FESEM) and x-ray diffraction (XRD). The photoluminescence spectra (PL) analysis noted that UV emission band is the band-to-band emission peak and the emission bands in the visible range are attributed to the oxygen vacancies, Zn interstitials, or impurities. The field-emission properties of four kinds of ZnO nanorods have been invested and the awl-shaped nanorods of ZnO have preferable characteristics due to the smallest emitter radius on the nanoscale in the tip in comparison with other nanorods. The growth mechanism of the ZnO nanorods can be explained on the basis of the vapor–liquid–solid (VLS) processes.     

硝酸铟诱导的电沉积氧化锌纳米柱光学性质裁剪

为在新型太阳能电池等光电器件中应用ZnO纳米结构,需要对ZnO纳米结构阵列的几何形貌及光电物理性质进行裁剪与操控。采用电化学沉积路线制备ZnO纳米柱阵列,In(NO3)3与NH4NO3两种盐类被溶入在传统Zn(NO3)2主电解液中。对ZnO纳米柱阵列进行扫描电子显微镜、透射反射光谱、光致发光光谱测试,分析其形貌与光电物理性质。随着引入的In(NO3)3浓度的增加,ZnO纳米柱阵列的平均直径随之由57 nm减小至30 nm。同时ZnO纳米柱的阵列密度也可降低,进而增大纳米柱间距至41 nm。由于新的盐类的引入,ZnO纳米柱的光学带隙由3.46 eV蓝移至3.55 eV。随着电解液中In(NO3)3的增加,ZnO纳米柱的斯托克斯位移由198 meV减小至154 meV,ZnO纳米柱中的非辐射复合可以得到一定程度的抑制。通过在主电解液中引入In(NO3)3与NH4NO3两种盐类,可对ZnO纳米柱的直径、密度、间距、透射反射率、光学带隙、近带边发射与非辐射复合进行操控与裁剪。     

Effect of zinc nitrate concentration on the structural and the optical properties of ZnO nanostructures

ZnO nanorods and nanodisks were formed on indium-tin-oxide-coated glass substrates by using an electrochemical deposition method. Scanning electron microscopy images showed that the ZnO nanorods were transformed into nanodisks with increasing Zn(NO₃)₂ concentration. X-ray diffraction patterns showed that the ZnO nanostructures had wurzite structures. The full widths at half maxima of the near band-edge emission peak of photoluminescence spectra at 300 K for ZnO nanorods were small, indicative of the high quality of the nanorods. These results indicate that the structural and the optical properties of ZnO nanostructures vary by changing Zn(NO₃)₂ concentration.     

Effect of Mn doping on the microstructures and photoluminescence properties of CBD derived ZnO nanorods

Mn-doped ZnO nanorods were synthesized from aqueous solutions of zinc nitrate hexahydrate, manganese nitrate and methenamine by the chemical solution deposition method (CBD). Their microstructures, morphologies and optical properties were studied in detail. X-ray diffraction (XRD) results illustrated that all the diffraction peaks can be indexed to ZnO with the hexagonal wurtzite structure. Scanning electron microscope (SEM) results showed that the average diameter of Mn-doped ZnO nanorods was larger than that of the undoped one. Photoluminescence (PL) spectra indicated that manganese doping suppressed the emission intensity and caused the blue shift of UV emission position compared with the undoped ZnO nanorods. In the Raman spectrum of Mn-doped ZnO nanorods, an additional mode at about 525 cm⁻¹ appeared which was significantly enhanced and broadened with the increase of Mn doping concentration.     

ZnO Nanorods Produced by the Method of Arc Discharge

ZnO nanorods are fabricated by arc discharge with ZnO powder as source materials. The sample is characterized by x-ray diffraction, Raman scattering spectra, scanning electron microscopy and high-resolution transmission electron microscopy. The ZnO nanorods exhibit single crystals with the hexagonal wurtzite structure. Many of them are tetrapod-like. The diameters range from several nanometres to about lOOnm, and the main diameters of the nanorods is around 20nm. The length-to-diameter ratio is more than 5, and the grown directions are along the [001] axis. Photoluminescence spectra show a narrow ultraviolet emission at around 389nm and a broad green emission at around 520 nm. The growth process can be interpreted by the vapour-solid mechanism.     

ZnO Nanostructures Grown on A1N/Sapphire Substrates by MOCVD

ZnO nanorods and nanotubes are successful synthesized on A1N/sapphire substrates by metal-organic chemical vapour deposition （MOGVD）. The different morphology and structure properties of ZnO nanorods and nanotubes are found to be affected by the A1N under-layer. The photoluminescence spectra show the optical properties of the ZnO nanorods and nanotubes, in which a blueshift of UV emission is observed and is attributed to the surface effect.[第一段]     

Influence of the morphology of ZnO nanostructures on luminescent and photovoltaic properties

Arrays of ZnO nanorods and nanoplates are synthesized by the hydrothermal and electrochemical methods, respectively. The photoluminescence spectra indicate that the nanoplates have a more defective structure than the nanorods. The obtained ZnO nanostructures are used as the basis to construct dye-sensitized solar cells. The influence of morphology and defectiveness of ZnO nanostructures on the luminescent and photovoltaic properties of the cells is studied.