Micromegas prototypes with thermo-bond film separators

In this paper we report the results of Micromegas prototypes constructed by attaching micromesh to an anode using thermo-bond films. The excellent metal attaching ability and good dielectical property of this kind of film make it a promising material to be used as avalanche gap spacers. Several prototypes are successfully made. The electron transmission properties are first studied and then the gas gain is measured in argon-isobutane mixtures. The maximum gain of more than 10⁴ is easily obtained. The energy resolutions for ⁵⁵Fe 5.9 keV K_α ray can be better than 20% over one magnitude in gain for different operational gas mixtures and the best energy resolution of 13.7% (FWHM) can be achieved with the gas mixture of 94% argon concentration. The preliminary test results of the prototypes with sensitive area of 45 mm×45 mm without internal support show good uniformity across the sensitive area.     

MICROMEGAS探测器初步测试

介绍了一种利用鱼线做放大区间隔的MICROMEGAS探测器, 灵敏面积为50 mm ×50 mm。 在Ar+CO₂（10%）气体条件下, 利用55Fe源5.9 keV的 X射线对MICROMEGAS探测器进行了初步测试: 计数率大于103 Hz的条件下, 计数率坪长达到280 V; 当栅极电压在800 V时能量分辨为30%; 当增益高于104时打火率低于10-4; PCB板读出条周期为400 μm条件下的位置分辨好于120 μm。 结果表明, 研制的MICROMEGAS探测器达到了初步设计的基本要求。 In this paper,A MICROMEGAS(Micro Mesh Gaseous Structure) detector with the amplification gap defined by stretching nylon fishing lines has been described . And its count plateau, gas gain and energy resolution in the condition of a 55Fe X ray source and Ar CO₂ (10%) mixture gases are measured as functions of mesh voltage. The count plateau approaches 280 V at the count rate of 103 Hz. The discharge rate is less than 10－4 when the gas gain is up to 104. The energy resolution is 30% (FWHM) based on －800 V mesh voltage. The position resolution is less than 120 μm at the condition of the sensitive area (50 mm×50 mm) Printed Circuit Boards (PCB) and its strip pitch of 400 μm. The results can satisfy the basic demand of MICROMEGAS detector preliminary design.     

氦氢混合气体中受激拉曼散射的脉宽特性

 308nm准分子激光泵浦的氢拉曼散射介质中渗入一定比分的氦气，其输出的一阶斯托克斯光S1的脉宽将发生变化。实验获得不同氦比分的S1脉宽在20-45ns之间，与渗入氦的浓度有关。从氦对氢拉曼增益系数的影响，对实验结果进行了理论分析。     

氦氢混合气体中受激拉曼散射的脉宽特性

308nm准分子激光泵浦的氢拉曼散射介质中渗入一定比分的氦气,其输出的一阶斯托克斯光S1的脉宽将发生变化。实验获得不同氦比分的S1脉宽在20-45ns之间,与渗入氦的浓度有关。从氦对氢拉曼增益系数的影响,对实验结果进行了理论分析。     

用于中国散裂中子源多功能反射谱仪的高气压多丝正比室探测器的研制

中国散裂中子源需要建设一台多功能反射谱仪中子探测器,满足在10年运行期间内,50%(@2A)以上的探测效率、好于2 mm的二维位置分辨、200 mm×200 mm的灵敏面积、3倍的n/γ分辨能力及良好的二维成像性能.基于此要求,探测器因此采用基于高气压~3He气体的多丝正比室,并以满足反射谱仪的探测效率、位置分辨、长期稳定工作和n/y分辨能力为目标进行探测器的设计.本文经过模拟和实验计算得出:以9 mm厚的铝合金入射窗、铝丝密封的高气压腔体和6 bar~3He+2.5 bar C_3H_8的工作气体的设计,可满足探测器对2 A中子10年运行期间内54%以上的探测效率要求;探测器对中子的位置分辨可达到1.4 mm左右;设计的气体净化系统,拥有2 L/min的气流速度可有效去除探测器内的负电性杂质气体,气体循环净化后可提高探测器约27%的气体增益,保证探测器长期稳定的运行;通过对~(252)Cf中子源的能谱测量和成像测量,得出探测器的n/γ分辨能力在5倍以上和均匀的成像结果.研制的探测器满足反射谱仪需求,并已在中国散裂中子源反射谱仪靶站就位联调.     

Design and performance of a 2-D multi-wire position sensitive X-ray detector

A 2-D multi-wire position sensitive detector for X-ray diffraction and small angle X-ray scattering studies is described. The detector has an active area of 100 mm × 100 mm and consists of an anode plane with 10 μm SS wires at 3 mm spacing and a pair of orthogonal cathode readout planes with 25 μm SS wires placed at 1.5 mm spacing. The position information is obtained using charge division method and recorded using a laboratory built data acquisition system. The resolution and gas gain was measured for 5.9 keV X-rays (⁵⁵Fe-source) as a function of the anode wire voltage and gas pressure. It was observed that the proportional region of the PSD at 100 kPa pressure extended up to a high voltage value of around 1.5 kV and it shifted to high values up to 2 kV for gas pressure of 300 kPa. The energy resolution improved from 18% (FWHM) to 12% with increase in pressure. The spatial resolution of the PSD also showed improvement, with a value of 1.2 mm × 1.4 mm at 300 kPa gas pressure. A maximum gain of 5 × 10⁴ is obtained.     

基于复合结构的气体电子倍增器增益模拟和实验研究

气体电子倍增器(GEM)作为高性能的微结构气体探测器在高能物理相关领域内得到了广泛的研究和应用.其中增益是GEM探测器基本性能研究中的一个重要参数,该值的精确测量至关重要.增益的测量一般采用电流测量或者能谱测量方法,但均存在精度较低或者过程繁琐的问题,且无法精确测量低增益值.针对GEM探测器增益的精确测量,本文提出了一种由GEM探测器与微网结构气体探测器(MM)级联构成的复合结构探测器(GEM-MM).利用GEM-MM结构以相对方法实现GEM增益的精确测量.该方法既可以省去传统方法中复杂的电子学标定过程,同时不需要进行原初电离电子数的估算,保证了增益的精确测量,并且可以实现GEM低增益的测量.基于GEM-MM测量GEM增益的原理,本文首先对GEM-MM电荷输运过程进行了模拟研究,优化了合适的工作电压.比较了三种不同类型和配比工作气体下GEM增益模拟结果,并在Ar/iC_4H_(10)(95/5)气体中测量了单层GEM在3—24范围内的有效增益.不同Penning系数下GEM增益的模拟结果表明,Penning系数为0.32时GEM增益的模拟结果与实验测量结果符合得很好.由此可以确定一个大气压下的Ar/iC_4H_(10)(95/5)气体中,Penning系数为0.32±0.01.     

传输线充电技术实现高功率亚纳秒电磁脉冲调制

 分析比较了阻抗匹配和失配情况下传输线充电的原理和波过程。分析结果表明：失配情况下的最大优点是能够实现脉冲功率增益。应用阻抗为27 W、长度为540 mm传输线为充电传输线和长度分别为30,45,60 mm、阻抗均为5 W传输线为被充电传输线进行了对比试验。实验结果表明：在距离辐射天线6 m处，输出辐射场强随低阻抗传输线长度增加而略有增加，最大辐射场强为49 kV/m,考虑气体开关的实际能量损耗，这与理论分析的充电电压和功率增益关系相吻合；长度为45 mm的5 W被充电传输线的输出脉冲前沿约210 ps,幅度约为150 kV。     

传输线充电技术实现高功率亚纳秒电磁脉冲调制

分析比较了阻抗匹配和失配情况下传输线充电的原理和波过程。分析结果表明：失配情况下的最大优点是能够实现脉冲功率增益。应用阻抗为27 W、长度为540 mm传输线为充电传输线和长度分别为30,45,60 mm、阻抗均为5 W传输线为被充电传输线进行了对比试验。实验结果表明：在距离辐射天线6 m处,输出辐射场强随低阻抗传输线长度增加而略有增加,最大辐射场强为49 kV/m,考虑气体开关的实际能量损耗,这与理论分析的充电电压和功率增益关系相吻合;长度为45 mm的5 W被充电传输线的输出脉冲前沿约210 ps,幅度约为150 kV。     

三级GEM探测器的增益一致性实验研究

随着二维GEM气体探测器在X射线成像探测领域的应用, 三级GEM的探测结构和电场均匀性带来的增益一致性修正问题, 成为需要深入研究的课题内容。 介绍了有效探测面积为100 mm×100 mm的三级倍增GEM探测器, 共采用100路阵列读出, 每路读出Pad面积为9.5 mm×9.5 mm。 测量了55Fe放射源准直入射的全能峰谱。 实验表明, 随着时间的变化, 探测器的增益基本上保持稳定; 随气流的增大, 增益由变化明显到变化不大。 GEM探测器各个阵列单元的增益一致性良好（>80%）; 能量分辨率在0.18～0.22之间, 运用最小二乘法拟合给出增益一致性的修正结果, 修正后相差约0.1, 为GEM气体探测器的增益一致性修正方法提供了参考方案。 With the application of the two dimensional GEM gaseous detector in X ray imaging, the correction method of gain uniformity caused by triple GEM avalanche structures and electric field uniformity should be studied. The paper reported the study of the triple GEM detector with effective area 100 mm×100 mm used the Pad’s size of 9.5 mm×9.5 mm. In the test, 100 readout channels were designed. Results showed that gain remained stable over time; as air flow increases, gain from increases obviously to changes very little. Particularly, triple GEM’s gain uniformity was very good (more than 80%) and the range of energy resolution was from 0.18 to 0.22. To improve gain consistency of results, the difference value revised was obtained to be about 0.1 by the least square method. It provided a better method to improve gain uniformity of GEM detector.     

Development of a microstrip-based neutron detector

A gas-filled microstrip detector for thermal neutrons has been built and successfully tested in our laboratory. The detector has an active area of 20 mm × 15 mm and consists of alternate anodes and cathodes of widths 12 μm and 300 μm respectively. The anode to cathode gap is 150 μm and the pitch is 612 μm. A high resistance, meandering type horizontal strip connects the anodes at one end and aids in position sensing by charge division method. The detector is tested with gas mixtures³He+Kr (1: 2) and³He+CF₄ (2:1) at pressure of 3 atmospheres and using a Pu-Be neutron source. The pulse height spectrum shows energy resolution of ∼8% (FWHM) for the 764 keV peak at anode voltage of 525 V for³He+Kr and ∼15% at anode voltage of 800 V for³He+CF₄. Gas gains up to 6.3 × 103 and 3.6 × 103 are obtained respectively with these gas mixtures. The overall efficiency of the detector along the sensitive length is tested by exposing the active area to neutrons and recording the position spectrum. The detector shows fairly uniform efficiency (∼45%) over the active length.     

Study of a sealed high gas pressure THGEM detector and response of alpha particle spectra

A sealed high gas pressure detector working in pure argon is assembled.It consists of a 5 cm x 5 cm PCB THGEM(THick Gaseous Electron Multiplier).The detector structure and experimental setup are described.The performance under high pressure(2 atm) is examined,selecting optimal voltages for the ionization region and induction region.The dependence of the shape of alpha particle spectra measured with relative gas gain on gas pressure(1.3-2.0 atm) has been studied.Eight data sets of relative gas gain versus working voltage of THGEM,expressed by weighting field E/P,are normalized,consistent with theory.The results show that the air tightness of the chamber is good,measured by a sensitive barometer and checked with gas gain.The experimental results are compared with Monte Carlo simulation of energy deposition without gas gain involved.     

Investigation of Gas Degradation in CO2 ? N2 Pulse Discharges I. Long Term Behaviour of Pulsed Laser Discharges in CO2 — N2 Gas Mixtures

The correlation between the plasma resistance and the laser output parameters has been investigated in pulsed CO₂ — N₂ discharges. The strong increase of the discharge resistance during gas degradation can be explained on the basis of strong attaching gas components. In degraded mixtures a supression of discharge instabilities together with the restoration of the laser pulse energy is possible by increasing the reduced electric field E/N temporarily.     

Experimental studies of THGEM in different Ar/CO_2 mixtures

In this paper, the performance of a type of domestic THGEM (THick Gaseous Electron Multiplier) working in Ar/CO₂ mixtures is reported in detail. This kind of single THGEM can provide a gain range from 100 to 1000, which is very suitable for application in neutron detection. In order to study its basic characteristics as a reference for the development of a THGEM based neutron detector, the counting rate plateau, the energy resolution and the gain of the THGEM have been measured in different Ar/CO₂ mixtures with a variety of electrical fields. For the Ar/CO₂(90%/10%) gas mixture, a wide counting rate plateau is achieved from 720 V to 770 V, with a plateau slope of 2.4%/100 V, and an excellent energy resolution of about 22% is obtained at the 5.9 keV full energy peak of the ⁵⁵Fe X-ray source.     

小型条纹管数值模拟及实验研究

针对无人机载及星载激光成像雷达系统对条纹管的小型化、高空间分辨率与大探测面积的应用需求,研制了一台具有高边缘空间分辨能力、高亮度增益的小型条纹相机.采用球面光电阴极、球面荧光屏技术提高了条纹相机的边缘空间分辨率和探测面积,有利于增大激光成像雷达的探测视场;采用狭缝型加速电极代替传统栅网电极,有利于提高条纹相机的电耐性和可靠性;设计了加载高达-15 kV工作电压的像缩小型条纹管,增大了条纹管的亮度增益,有助于增大激光雷达系统的探测距离.测试结果显示：在有效工作面积16 mm×2 mm内,条纹管静态空间分辨率高于29.3 lp/mm@MTF=5%（MTF表示调制传递函数）,亮度增益高达39.4.条纹相机光电阴极处静态空间分辨率高于15 lp/mm@CTF=11.64%（CTF表示对比度传递函数）;边缘动态空间分辨率高于9.8 lp/mm@CTF=5.51%;时间分辨率优于54.6 ps@T_screen=4.3 ns（T_screen为全屏时间）且在整个工作面积内具有较高的一致性;动态范围为345：1@54.6 ps.同时,为满足不同的景深及探测精度需求,相机设置六个扫描档位,可以实现不同扫速下的超快速目标诊断.该条纹相机在无人机载及星载激光成像雷达探测中具有潜在的实用价值.     

Study of a bulk-Micromegas with a resistive anode

The design and performance of a Micromegas with a resistive anode are presented in this paper. A thin resistive sheet with volume resistivity of 10¹² Ω·m cm is glued onto the readout electrode surface and its performance is investigated by using a ⁵⁵Fe X-ray radioactive source in the operation gas of argon and isobutene mixtures (Ar/Iso=95/5). The gas gain at different mesh high voltage, counting rate and working time are given. Energy spectra at different working voltages are measured and the results are discussed. We have oberved that a Micromegas with a resistive anode can be operated at higer gain than a standard Micromegas without sparks.     

Saturation of the net electron excitation of the CO2(00°1) laser level as a function of discharge input energy

Measurements are made of the small signal gain in He:CO₂ and He:N₂:CO₂ gas mixtures as a function of pulsed discharge energy. In all case it is found that the gain saturates as the discharge energy is increased. Thermal effects cannot account for this gain saturation which appears to be a fundamental property of high-pressure CO₂ discharges.     

高增益型气体电子倍增微网结构探测器的性能研究

随着微结构气体探测器的不断发展, 不同的探测需求相继提出.为了实现气体探测器在高增益和低打火率的条件下长时间稳定工作, 结合气体电子倍增器(GEM)与微网结构气体探测器(MicroMegas)的探测优势, 成功研制出一种基于GEM作为预放大的MicroMegas探测器, 详细介绍了探测器结构和工作原理, 并利用⁵⁵Fe放射源对探测器增益、打火率、能量分辨和工作稳定性等性能进行了实验测量. 分析结果显示GEM-MicroMegas探测器可以连续工作30 h 以上, 探测器增益可以超过10⁶, 相对于无GEM膜的MicroMegas探测器, 相同增益下打火率可以降低近100倍. 关键词： 微网结构气体探测器 能量分辨率 增益 打火率     

长波长激光驱动Ni-like Ag 13.9 nmX射线激光的理论研究

 为了进一步深入理解掠入射驱动碰撞机制的特点与长处，以基频光正入射驱动为参照，用系列程序研究了6 mm和3 mm激光正入射驱动类镍银碰撞激发机制。在波长6 mm的激光正入射驱动下，激光能量直接沉积到增益区，大大提高了增益区的电子温度；以5 J驱动能量，获得有效增益系数为20.7 cm^-1的高增益和有效增益长度积为41.4的深度饱和增益，与波长1.053 mm的正入射相比，以19%的驱动能量，使有效增益系数提高了60%。在波长3 mm的激光正入射驱动下，激光能量沉积到增益区附近，大大提高了增益区的电子温度；以15 J驱动能量，获得有效增益系数为21.2 cm^-1的高增益和有效增益长度积为42.4的深度饱和增益，与波长1.053 mm的正入射相比，以57%的驱动能量，使有效增益系数提高64%。     

长波长激光驱动Ni-like Ag 13.9 nmX射线激光的理论研究

为了进一步深入理解掠入射驱动碰撞机制的特点与长处,以基频光正入射驱动为参照,用系列程序研究了6 mm和3 mm激光正入射驱动类镍银碰撞激发机制。在波长6 mm的激光正入射驱动下,激光能量直接沉积到增益区,大大提高了增益区的电子温度;以5 J驱动能量,获得有效增益系数为20.7 cm-1的高增益和有效增益长度积为41.4的深度饱和增益,与波长1.053 mm的正入射相比,以19%的驱动能量,使有效增益系数提高了60%。在波长3 mm的激光正入射驱动下,激光能量沉积到增益区附近,大大提高了增益区的电子温度;以15 J驱动能量,获得有效增益系数为21.2 cm-1的高增益和有效增益长度积为42.4的深度饱和增益,与波长1.053 mm的正入射相比,以57%的驱动能量,使有效增益系数提高64%。