Features of the structure and properties of β-FeSi<Subscript>2</Subscript> nanofilms and a β-FeSi<Subscript>2</Subscript>/Si interface

The electronic, geometric, and magnetic structure of nanofilms of the β phase of iron disilicide FeSi₂ with the (001), (100), and (010) surfaces have been simulated through density functional calculations. A substantial reconstruction of the (001) surface terminated with silicon atoms has been observed, which was accompanied by an increase in the surface symmetry and appearance of “squares” of silicon atoms. Analysis of the electron density of states (DOS) and spin DOS projected on the contributions of layers of atoms (LSDOS) indicates that all plates have metallic properties. The main contribution near the Fermi level comes from the surface iron layers and it decreases rapidly with an increase in the distance from the surface of the plate. Analysis of the calculated effective magnetic moments of atoms shows that the surface layers in the plates have a significant magnetic moment, in particular, iron layers on the (001) surface (1.89 μ_B/atom). The moments of atoms decrease rapidly with an increase in their distance from the surface. The electron and geometric regions of a (001)Si/FeSi₂ interface have been studied. Analysis of the LSDOS shows that the surface conducting state mainly determined by the contribution from the near-surface silicide layers is implemented in this region. The possibility of the formation of the perfect and sharp Si/FeSi₂ interface has been demonstrated.     

Synthesis and characterization of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>–Ba<Subscript>0.9</Subscript>Sr<Subscript>0.1</Subscript>TiO<Subscript>3</Subscript> magnetoelectric composites with dielectric and magnetic properties

Composite structures consisting of (001)-oriented SrTiO₃ (STO)/La_0.7Sr_0.3MnO₃ (LSMO) films of 30 nm thickness, grown on an (001) Pb(Mg_1/3Nb_2/3)TiO₃– 28 mol.% PbTiO₃ piezoelectric relaxor-ferroelectric single-crystalline wafer were investigated by means of Wide-Angle X-ray Diffraction (WAXRD) in situ under influence of a d.c. electric field with strength E up to ±18 kV/cm. The WAXRD measurements of the films and substrate reflection profiles resulted in a determination of the strain s in the films and the substrate separately. The strained state of the STO/LSMO films is effectively controlled by a huge converse piezoelectric effect of the PMN-PT substrate. The coefficients of coupling between electric-field-induced out-of-plane strain in the films and in the substrate for the composite system STO/LSMO/PMN-PT are obtained.     

First principles study on electronic and optical properties of Al<Subscript>x</Subscript>Ga<Subscript>1−x</Subscript>N and In<Subscript>y</Subscript>Ga<Subscript>1−y</Subscript>N

The band structure, density of states of Al_xGa_1?xN and In_yGa_1?yN was performed by the first-principles method within the local density approximation. The calculated energy gaps of the AlN, Al_0.5Ga_0.5N, GaN, In_0.5Ga_0.5N and InN were 5.48, 4.23, 3.137, 1.274 and 0.504 eV, which were in agreement with the experimental result. The dielectric functions, absorption coefficient and loss function were calculated based on Kramers–Kronig relations. Further more, the relationships between electronic structure and optical properties were investigated theoretically. For Al_xGa_1?xN and In_yGa_1?yN materials, the micromechanism of the optical properties were explained.     

Mössbauer and magnetic studies of the phase state of SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript>/La<Subscript>0.9</Subscript>Ca<Subscript>0.1</Subscript>MnO<Subscript>3</Subscript> composites

The formation of an intermediate phase in SrFe₁₂O₁₉/La_0.9Ca_0.1MnO₃ composites was demonstrated for the first time using only Mössbauer spectroscopy. The SrFe₁₂O₁₉/La_0.9Ca_0.1MnO₃ composite was prepared by the two-stage (sol–gel and hydrothermal) synthesis with varying initial conditions. The X-ray diffraction studies showed that the composite consisted of two phases: well-formed structures of manganite La_0.9Ca_0.1MnO₃ and hexagonal ferrite SrFe₁₂O₁₉. It was found that nanocrystalline La_0.9Ca_0.1MnO₃ particles with size d ? 150 nm formed in the composites at the surface of plate-like SrFe₁₂O₁₉ crystallites. The Mössbauer studies showed that the composite contained additional (intermediate) phase La_0.9Ca_0.1Mn(Fe)O₃ that formed at the interface between SrFe12O19 and La_0.9Ca_0.1MnO₃ phases. The intermediate phase concentration increased with the molar content of La_0.9Ca_0.1MnO₃; in this case, the fraction of the surface of SrFe₁₂O₁₉ crystallites coated with La_0.9Ca_0.1MnO₃ increased, which led to the increase in the total area of the interface surface and the intermediate phase concentration.     

Effect of the humidity on the uptake of NO<Subscript>3</Subscript> on coatings composed of MgCl<Subscript>2</Subscript> · 6H<Subscript>2</Subscript>O and MgBr<Subscript>2</Subscript> · 6H<Subscript>2</Subscript>O and mixtures thereof with NaCl

The reactive uptake of NO₃ radicals on the surface of wetted individual X salts and of wetted X-NaCl salts (X = MgCl₂ · 6H₂O and MgBr₂ · 6H₂O) at [H₂O] = 2 × 10¹²−2 × 10¹⁵ cm⁻³ and NO₃ (4.8 × 10¹² cm⁻³) was studied using a reactor with a movable insert covered with a salt coating in combination with a mass spectrometer for monitoring the initial reactant and products. The probabilities of NO₃ uptake γ on X-NaCl binary salts as functions of the content of doping salt were determined. A parametric approximation of the experimental data was proposed, which makes it possible to quantitatively predict the extent of surface enrichment of a wetted binary salt coating in doping salt and its dependence on the humidity and the content of this salt in the binary mixture. It was established that the relative surface density σ_X of X doping salt depends on its mole fraction μ_X in the X-NaCl binary salt as σ_X = aμ_X (a = 2.2 for MgBr₂ and 13.1 for MgCl₂) over the entire humidity range covered. The contributions of the X salts to the overall uptake of NO₃ at NO₃ concentration typical of the tropospheric conditions ([NO₃] ∼ 10⁷ cm⁻³ and relative humidities of RH ≤ 20%) were estimated.     

Controlled flame synthesis of αFe<Subscript>2</Subscript>O<Subscript>3</Subscript> and Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles: effect of flame configuration,flame temperature,and additive loading

Superparamagnetic iron oxide nanoparticles are used in diverse applications, including optical magnetic recording, catalysts, gas sensors, targeted drug delivery, magnetic resonance imaging, and hyperthermic malignant cell therapy. Combustion synthesis of nanoparticles has significant advantages, including improved nanoparticle property control and commercial production rate capability with minimal post-processing. In the current study, superparamagnetic iron oxide nanoparticles were produced by flame synthesis using a coflow flame. The effect of flame configuration (diffusion and inverse diffusion), flame temperature, and additive loading on the final iron oxide nanoparticle morphology, elemental composition, and particle size were analyzed by transmission electron microscopy (TEM), high-resolution TEM (HR-TEM), energy dispersive spectroscopy (EDS), and Raman spectroscopy. The synthesized nanoparticles were primarily composed of two well known forms of iron oxide, namely hematite αFe₂O₃ and magnetite Fe₃O₄. We found that the synthesized nanoparticles were smaller (6–12 nm) for an inverse diffusion flame as compared to a diffusion flame configuration (50–60 nm) when CH₄, O₂, Ar, and N₂ gas flow rates were kept constant. In order to investigate the effect of flame temperature, CH₄, O₂, Ar gas flow rates were kept constant, and N₂ gas was added as a coolant to the system. TEM analysis of iron oxide nanoparticles synthesized using an inverse diffusion flame configuration with N₂ cooling demonstrated that particles no larger than 50–60 nm in diameter can be grown, indicating that nanoparticles did not coalesce in the cooler flame. Raman spectroscopy showed that these nanoparticles were primarily magnetite, as opposed to the primarily hematite nanoparticles produced in the hot flame configuration. In order to understand the effect of additive loading on iron oxide nanoparticle morphology, an Ar stream carrying titanium-tetra-isopropoxide (TTIP) was flowed through the outer annulus along with the CH₄ in the inverse diffusion flame configuration. When particles were synthesized in the presence of the TTIP additive, larger monodispersed individual particles (50–90 nm) were synthesized as observed by TEM. In this article, we show that iron oxide nanoparticles of varied morphology, composition, and size can be synthesized and controlled by varying flame configuration, flame temperature, and additive loading.     

Magnetic and crystal structures of iron-ion-doped TbBaCo<Subscript>2</Subscript>O<Subscript>5 + γ</Subscript>

Neutron diffraction and magnetic studies of a TbBaCo₂O_{5 + γ} polycrystalline sample with a perovskite-like layered structure have revealed that spontaneous magnetization appears at 305 K and decreases sharply below 200 K. It has been shown that the crystal structure is described by space group Pmmm with a 2a _p · a _tp · 2a _p unit cell. The magnetic structure in the high-temperature magnetic phase consists of the G-type antiferromagnetic and ferromagnetic components, whereas the magnetic structure in the low-temperature phase is a G-type antiferromagnetic. The ferromagnetic component appears due to the noncollinearity of the magnetic moments of Co³⁺ ions, which are in the high-spin state in pyramids and in the low-spin state in octahedrons. The antiferromagnetic component is present in the octahedral sublattice, because oxygen vacancies are partially ordered.     

Mass and kinetic energy distribution of the species generated by laser ablation of La<Subscript>0.6</Subscript>Ca<Subscript>0.4</Subscript>MnO<Subscript>3</Subscript>

The mass distributions of the species generated by laser ablation from a La_0.6Ca_0.4MnO₃ target using laser irradiation wavelengths of 193 nm, 266 nm and 308 nm have been investigated with and without a synchronized gas pulse of N₂O. The kinetic energies of the species are measured using an electrostatic deflection energy analyzer, while the mass distributions of the species were analyzed with a quadrupole mass filter. In vacuum (pressure 10⁻⁷ mbar), the ablation plume consists of metal atoms and ions such as La, Ca, Mn, O, LaO, as well as multiatomic species, e.g. LaMnO⁺. The LaO⁺ diatomic species are by far the most intense diatomic species in the plume, while CaO and MnO are only detected in small amounts. The interaction of a reactive N₂O gas pulse with the ablation plume leads to an increase in plume reactivity, which is desired when thin manganite films are grown, in order to incorporate the necessary amount of oxygen into the film. The N₂O gas pulse appears to have a significant influence on the oxidation of the Mn species in the plume, and on the creation of negative ions, such as LaO⁻,O⁻ and O₂⁻.     

Effect of annealing temperature on microstructures and optical properties of Ba<Subscript>0.9</Subscript>Sr<Subscript>0.1</Subscript>TiO<Subscript>3</Subscript> films

Evolution of microstructure and optical property with annealing temperature has been examined for Ba_0.9Sr_0.1TiO₃ films derived from one single precursor solution containing polyethylene glycol polymer. The films sintered below 750°C exhibit a uniform phase structure across the cross-sections and an ordinary optical thin film feature, while the Ba_0.9Sr_0.1TiO₃ films crystallized at 750°C or higher temperature render a lamellar texture consisting of dense and porous Ba_0.9Sr_0.1TiO₃ layers and a good performance as a one-dimensional photonic crystal. The discrepancy in cross-sectional morphology and reflectance property observed in these Ba_0.9Sr_0.1TiO₃ films has been preliminarily explained.     

μSR study of Eu<Subscript>0.8</Subscript>Ce<Subscript>0.2</Subscript>Mn<Subscript>2</Subscript>O<Subscript>5</Subscript> and EuMn<Subscript>2</Subscript>O<Subscript>5</Subscript> multiferroics

A comparative μSR study of ceramic samples of the EuMn₂O₅ and Eu_0.8Ce_0.2Mn₂O₅ multiferroics is performed in the temperature range from 15 to 300 K. It is found that the Ce doping of the EuMn₂O₅ sample slightly reduces the temperature of the magnetic phase transition from T _N = 45 K for the EuMn₂O₅ sample to T _N = 42.5 K for the Eu_0.8Ce_0.2Mn₂O₅ sample. Below the temperature T _N for both samples, there are two types of localization of a thermalized muon with different temperature dependences of the precession frequency of the magnetic moment of the muon in an internal magnetic field. The higher frequency in both samples refers to the initial antiferromagnetic matrix. The behavior of this frequency in Eu_0.8Ce_0.2Mn₂O₅ follows the Curie–Weiss law with the exponent β = 0.29 ± 0.02, which differs from the value β = 0.39 standard for 3D Heisenberg magnetics and is observed in EuMn₂O₅, because of the strong frustration of the doped sample. The temperature-independent low frequency is due to the presence of Mn³⁺–Mn⁴⁺ ferromagnetic pairs located along the b axis of the antiferromagnetic matrix and in the regions of phase separation, which contain such ion pairs and e _g electrons recharging them. In both samples, polarization losses are the same (about 20%) and are associated with the formation of Mn⁴⁺–Mn⁴⁺ + Mu complexes near Mn³⁺–Mn⁴⁺ ferromagnetic pairs. In the temperature interval from 25 to 45 K, the separation of the Eu_0.8Ce_0.2Mn₂O₅ structure into two fractions where the relaxation rates of polarization of muons differ by an order of magnitude is revealed. This effect is due to a change in the state of regions of phase separation (1D superlattices) at the indicated temperatures. Such effect in EuMn₂O₅ is significantly weaker.     

Magnetic and magnetoresistive properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sr<Subscript>2</Subscript>FeMoO<Subscript>6–δ</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoheterostructures

A method has been developed for fabricating nanoporous matrices based on anodic aluminum oxide for the deposition of ferromagnetic nanoparticles in them. The modes of deposition of strontium ferromolybdate thin films prepared by the ion-plasma method have been worked out, and the magnetic and magnetoresistive properties, structure, and composition of the films have been investigated. It has been revealed that the microstructure and properties of the strontium ferromolybdate films deposited by ionplasma sputtering depend on the deposition rate and the temperature of the substrate. Based on the measurement of the electrical resistivity of nanoheterostructures in a magnetic field, it has been found that the magnetoresistance reaches 14% at T = 15 K and B = 8 T, which is due to the manifestation of tunneling magnetoresistance.     

Maxwell–Wagner relaxation and magnetodielectric properties of Bi<Subscript>0.5</Subscript>La<Subscript>0.5</Subscript>MnO<Subscript>3</Subscript> ceramics

The complex permittivity ε = ε′–iε″ of manganite bismuth–lanthanum Bi_0.5La_0.5MnO₃ ceramics has been measured at temperature T = 78 K in the frequency range f = 200–10⁵ Hz and in the magnetic induction range B = 0–5 T. Dielectric relaxation and the pronounced magnetodielectric effect have been detected. The explanation based on the superposition of Maxwell–Wagner relaxation and the magnetoresistance effect has been proposed.     

Mechanism of the oxidation and combustion of normal paraffin hydrocarbons: Transition from C<Subscript>1</Subscript>–C<Subscript>6</Subscript> to C<Subscript>7</Subscript>H<Subscript>16</Subscript>

A previously proposed algorithm for constructing an optimal mechanism of the high- and low-temperature oxidation and combustion of normal paraffin hydrocarbons was used, which includes the major processes that determine the rate of reaction and the formation of the main intermediate and final products. The mechanism has the status of a nonempirical detailed mechanism, since all the constituent elementary reactions have a kinetic substantiation. The mechanism has two specific features: it included no reactions of so-called double addition of oxygen and no isomeric compounds and derivatives thereof as intermediate species. Realization of this algorithm leads to fairly compact models, a circumstance important for studies of chemical processes involving paraffin hydrocarbons C _n with large n. Previously, based on this algorithm, compact mechanisms of oxidation and combustion of propane, n-butane, n-pentane, and n-hexane were constructed. In this paper, we develop a nonempirical detailed mechanism of oxidation and combustion of n-heptane. The most important feature of the new mechanism is its ability to predict the staging of the process in the form of cool and blue flames at low autoignition temperatures. A comparison of the simulation results with the available experimental data is conducted.     

Effect of process parameters and post-deposition annealing on the microwave dielectric and optical properties of pulsed laser deposited Bi<Subscript>1.5</Subscript>Zn<Subscript>1.0</Subscript>Nb<Subscript>1.5</Subscript>O<Subscript>7</Subscript> thin films

Bismuth Zinc niobate (Bi_1.5Zn_1.0Nb_1.5O₇) thin films were deposited by pulsed laser deposition (PLD) method on fused silica substrates at different oxygen pressures. The structural, microwave dielectric and optical properties of these thin films were systematically studied for both the as-deposited and the annealed films at 600°C. The as-deposited films were all amorphous in nature but crystallized on annealing at 600°C in air. The surface morphology as studied by atomic force microscopy (AFM) reveals ultra-fine grains in the case of as-deposited thin films and cluster grain morphology on annealing. The as-deposited films exhibit refractive index in the range of 2.36–2.53 (at a wavelength of 750 nm) with an optical absorption edge value of 3.30–3.52 eV and a maximum dielectric constant of 11 at 12.15 GHz. On annealing the films at 600°C they crystallize to the cubic pyrochlore structure accompanied by an increase in band gap, refractive index and microwave dielectric constant.     

AC conductivity and dielectric behavior of low-temperature phase of α-AgCuPO<Subscript>4</Subscript>

The copper monophosphate compound, α-AgCuPO₄, was prepared by the conventional solid-state reaction. The purity of the compound was checked by X-ray diffraction technique (XRD). Detailed dielectric and electrical properties of the compound were analyzed as a function of frequency (209 Hz–1 MHz) and temperature (343–514 K). The AC conductivity has been fitted and studied using Jonscher’s equation, whose exponent n varied with the temperature, showing that the overlapping large polaron tunneling model (OLPT) is the appropriate model to describe the electrical conduction mechanism.     

Influence of Matrix Nature on the Structural Characteristics of In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CeO<Subscript>2</Subscript> and SnO<Subscript>2</Subscript>–CeO<Subscript>2</Subscript> Composites Fabricated by the Impregnation Method

The structural characteristics, valence states, and distribution of cerium ions between the components in In₂O₃–CeO₂ and SnO₂–CeO₂ nanocomposites fabricated using the impregnation method were studied. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) were used to show that, during impregnation, cerium ions are not included into In₂O₃ crystals and are disposed only on their surface in the form of nano-sized crystallites or amorphous clusters. On the other side, under the contact of CeO₂ clusters with a surface of SnO₂ matrix crystals, cerium ions penetrate into the surface layer of these crystals. In contrast to an In₂O₃–CeO₂ system, where the addition of CeO₂ does not affect the conduction activation energy, where cerium oxide is added to SnO₂, the observed increase in the resistance of a SnO₂–CeO₂ composite is accompanied by a sufficient increase in activation energy. These data and the XPS spectra confirm the modification of the surface layers of conductive SnO₂ crystals as, a result of the penetration of cerium ions into these layers.     

Preparation,structure and properties of La<Subscript>0.67</Subscript>Pb<Subscript>0.33</Subscript>(Mn<Subscript>1-x</Subscript>Co<Subscript>x</Subscript>)O<Subscript>3-δ</Subscript>

La_0.67Pb_0.33(Mn_1-xCo_x)O_3-δ ceramics with x=0, 0.01, 0.03, 0.06, 0.1 and 0.15 have been prepared in a two-step procedure. Precursor gels were made by the wet chemical malic acid method. The gels were calcined and then converted into ceramics by heat treatment at 950 °C and 1000 °C in air. X-ray diffraction showed that the compounds were phase pure. The crystal structure symmetry of the compounds was confirmed to be rhombohedral (space group R3̄c) for the whole investigated range of x. All compounds undergo a paramagnetic–ferromagnetic phase transition between 335 K and 225 K. The basic magnetic characteristics such as the Curie temperature , the paramagnetic Curie temperature θ, the effective magnetic moment and the saturated magnetization decrease with increasing Co doping. The ferromagnetic transition is accompanied by an anomaly in the electrical resistance for all compounds. The high-temperature insulator–metal transitions () do not coincide with the relevant . A large magnetoresistance peak of about 15% was observed for all compounds at . PACS 72.80.Ga; 75.47.Lx; 75.60.Ej     

Synthesis and characterization of oxide cathode materials of the system (1-x-y)LiNiO<Subscript>2</Subscript>·xLi<Subscript>2</Subscript>MnO<Subscript>3</Subscript>·yLiCoO<Subscript>2</Subscript>

Composite cathode materials produced by integrating isostructural (2D-layered) compounds LiNiO₂, LiCoO₂, and Li₂MnO₃ (Li(Li_1/3Mn_2/3)O₂) have been investigated utilizing a compositional phase diagram. The samples were characterized by multiple techniques to establish structure–property relationships. Specifically, for structural characterization, powder X-ray diffraction, scanning electron microscopy, thermo-gravimetric analysis, and X-ray photoelectron spectroscopy were carried out. For properties, electrochemical characterization was carried out. The best composition showed a discharge capacity of 244 mAh/g (C/15 rate) in the testing range of 4.6–2 V, with good coulombic efficiency and cyclability.     

High resolution diffraction and small angle scattering neutron investigations of LaCo<Subscript>0.5</Subscript>Mn<Subscript>0.5</Subscript>O<Subscript>3+</Subscript><Subscript>δ</Subscript>: effect of oxygen content

We have investigated LaCo_0.5Mn_0.5O_{3+ δ} compounds with different oxygen content by means of magnetization, high resolution and small-angle neutron diffraction measurements. Oxygen content decrease down to stoichiometric composition leads to an essential increase of T_C and magnetic moment while Co/Mn ionic ordering degree is kept almost constant. It is assumed that upon oxygen reduction Co³⁺ ions change their valence state down to 2+ one that leads to dominating of Co²⁺-Mn⁴⁺ ferromagnetic interactions as well as T_C increase. Magnetic properties can be explained in terms of coexistence of long-range ferromagnetic order and short-range clusters with antiferromagnetic interactions prevailing. Size distribution of the mentioned short-range magnetic inhomogeneities is rather mild within the samples but it is strongly temperature dependent.     

Sol–gel synthesis and characterization of Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite solid electrolytes

Composite solid electrolytes in the system (1???x)Li₂CO₃–xAl₂O₃, with x?=?0.0–0.5 (mole), were synthesized by a sol–gel method. The synthesis carried out at low temperature resulted in voluminous and fluffy products. The obtained materials were characterized by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy/energy-dispersive X-ray, Fourier transform infrared spectroscopy and AC impedance spectroscopy. Structural analysis of the samples showed an amorphous feature of Li₂CO₃ and traces of α-LiAlO₂, γ-LiAlO₂ and LiAl₅O₈. The prepared composite samples possess high ionic conductivities at 130–180 °C on account of the presence of lithium aluminates as well as the formation of a high concentration of an amorphous phase of Li₂CO₃ via this sol–gel preparative technique.