Effects of polyethylenimine on morphology and property of ZnO films grown in aqueous solutions

Morphologies and properties of well-aligned ZnO films were controlled using zinc nitrate-hexamethylenetetramine aqueous solutions with the addition of polyethylenimine as a surfactant. Porous and dense ZnO films were fabricated with and without polyethylenimine, respectively. The addition of polyethylenimine proceeded to form porous ZnO whiskers film by preferential adsorption to nonpolar crystal faces and modifications of the surface free energy and growth rate. Dense ZnO film showed high transmittance of 80%, and low intensity of fluorescence and photo-induced current. Porous ZnO whiskers film showed low transmittance of 70%, while high intensity of fluorescence and high photo-induced current were detected because the porous ZnO nanowhisker film possessed a large interior surface area which can capture large amounts of DNA molecules labeled with dye molecules on the surface of ZnO crystals. High performance dye-sensitized sensors can be produced using ZnO whisker films prepared from an aqueous solution.     

Optoelectronics and formaldehyde sensing properties of tin-doped ZnO thin films

Sn-doped ZnO thin films were deposited on clean glass substrates using the chemical spray pyrolysis technique. XRD analyses confirm stable ZnO hexagonal wurtzite structure of the films with crystallite size in the range of 20–28 nm. The surface roughness of the films increases on Sn doping, which favors to higher adsorption of oxygen species on the film surface, resulting in higher gas response. Optical studies reveal that the band gap decreases on Sn doping. All the films show near band edge emission, and on Sn doping the luminescence peak intensity has been found to increase. Photocurrent in the 1.5 at.% doped film enhances about three times to that observed in the undoped ZnO film. Among all the films examined, the 1.5 at.% Sn-doped film exhibits the maximum response (～94.5 %) at the operating temperature of 275?°C for 100 ppm concentration of formaldehyde, which is much higher than the response (～35 %) in the undoped film. The gas response of the film is attributed to the chemisorption of oxygen on the film surface and the subsequent reaction between the adsorbed oxygen species and the formaldehyde molecules.     

Sn掺杂ZnO薄膜的室温气敏性能及其气敏机理

采用化学气相沉积方法在预制好电极的玻璃基底上制备出Sn掺杂ZnO薄膜和纯ZnO薄膜. 两种样品典型的形貌为四足状ZnO晶须, 其直径约为150-400 nm, 呈疏松状结构. 气敏测试结果显示Sn掺杂ZnO薄膜具有优良的室温气敏性, 并对乙醇具有良好的气敏选择性, 而纯ZnO薄膜在室温条件下对乙醇和丙酮均没有气敏响应. X射线衍射结果表明两种样品均为六方纤锌矿结构. Sn掺杂ZnO样品中没有出现Sn及其氧化物的衍射峰, 其衍射结果与纯ZnO样品对比, 衍射峰向小角度偏移. 光致发光结果表明, Sn掺杂ZnO薄膜与纯ZnO薄膜均出现紫外发光峰和缺陷发光峰, 但是Sn的掺杂使得ZnO的缺陷发光峰明显增强. 将Sn掺杂ZnO样品在空气中退火后, 其室温气敏性消失, 说明Sn掺杂ZnO样品的室温气敏性可能与其缺陷含量高有关. 采用自由电子散射模型解释了Sn掺杂ZnO薄膜的室温气敏机理.     

Preparation of nanocone ZnO thin film and its aging effect of photoluminescence

In this work, a nanocone ZnO thin film was prepared by electron beam evaporation on a Si (1 0 0) substrate. The structural properties of the film were investigated by X-ray diffraction (XRD), atomic force microscopy and laser Raman scattering, respectively. The aging effect of the nanocone ZnO thin film was studied by photoluminescence spectra. The structural analyses show that the prepared ZnO thin film has a hexagonal wurtzite structure and is preferentially oriented along the c-axis perpendicular to the substrate surface. The photoluminescence spectra show that with the increase of aging time, the green emission of the nanocone ZnO thin film gradually decreases while the ultraviolet emission somewhat increases. The reason for this phenomenon is likely that the green-emission-related oxygen vacancies in the film are gradually filled up. The Raman scattering analyses also suggest that the intensity of the Raman peak related to oxygen vacancies in the nanocone ZnO thin film declines after the film is aged in air for a year. Therefore, the authors think the green emission is mainly connected with oxygen vacancy defects.     

Sputter-deposited ZnO thin films consisting of nano-networks for binder-free dye-sensitized solar cells

ZnO nano-network structures with high porosity were prepared for use in the photoelectrodes of binder-free dye-sensitized solar cells (DSSCs) by DC sputtering and subsequent thermal oxidation. Zn thin films prepared at 100 °C showed nano-network structures with high porosity, while those prepared at 25 °C did not. This was partially attributed to the high mobility of sputter-deposited particles that arrived at the surface of the substrate and partially to a supersaturation mechanism. The prepared nano-network Zn was successfully transformed to ZnO without a morphological change via subsequent annealing in air. The power conversion efficiency of DSSCs based on the ZnO nano-network structures exhibited 10 times higher efficiency than those based on ZnO film prepared at 25 °C because of its large surface area for adsorption of dye molecules. The thickness of the ZnO nano-network structures increased linearly at 10 μm h^?1 as a function of sputter time. As the film thickness increased, the power conversion efficiency of DSSCs increased from 1.09% to 1.82%.     

Hybrid photoanode films based on sparse ZnO rod array-TiO2 nanoparticles in dye-sensitized solar cells

ZnO-TiO2 hybrid photoanodes were fabricated via the doctor-blade method by integrating vertically-grown sparse ZnO arrays with hydrothermal TiO2 nanoparticles. A special surface-coating technique was developed to deposit a thin TiO2 layer on the surface of ZnO rods. Microstructure, optical and photoelectrochemical performance of the hybrid photoanodes were investigated. The denser ZnO array exhibited bad filling behavior of nanoparticles in the interspace of ZnO rods, strong scattering and low conversion efficiency (0.27%). The sparser array showed a much better integrated microstructure, improved transmittance and high conversion efficiency (2.68%). The surface modification of ZnO rods by the TiO2 thin layer was found useful in improving the interfacial microstructure between the ZnO rod and the TiO2 bulk film, and the total conversion efficiency of 3.01% was achieved, higher than that of the pure TiO2 nanoparticle cell (2.93%). The increased scattering effects on the incident light, the enhanced electron transportation at TiO2/dye/electrolyte interface, and the inhabited recombination were responsible for this improvement.     

脉冲激光沉积法制备的ZnO薄膜的低阈值电抽运紫外随机激射

分别采用直流反应溅射法和脉冲激光沉积法在硅衬底上沉积ZnO薄膜, 用X射线衍射、扫描电镜、光致发光谱等手段对两种方法沉积的ZnO薄膜的结晶状态、 表面形貌和光致发光等进行了表征. 进一步对比研究了以上述两种方法制备的ZnO薄膜作为发光层的金属-绝缘体-半导体结构器件的电抽运紫外随机激射. 结果表明, 与以溅射法制备的ZnO薄膜作为发光层的器件相比, 以脉冲激光沉积法制备的ZnO薄膜为发光层的器件具有更低的紫外光随机激射阈值电流和更高的输出光功率. 这是由于脉冲激光沉积法制备的ZnO薄膜中的缺陷更少, 从而显著地减少了紫外光在光散射过程中的光损耗. 关键词： 随机激射 ZnO薄膜 脉冲激光沉积 溅射     

Effect of thickness on the stability of transparent conducting impurity‐doped ZnO thin films in a high humidity environment

The resistivity of transparent conducting Al‐ and Ga‐doped ZnO (AZO and GZO) thin films prepared with a thickness in the range from 20 to 200 nm on glass substrates at a temperature below 200 °C was found to increase with exposure time when tested in a high humidity environment (air at 90% relative humidity and 60 °C). The resistivity stability (resistivity increase) was considerably affected by the thin film thickness. In particular, thin films with a thickness below about 50 nm were very unstable. The increase in resistivity is interpreted as carrier transport being dominated by grain boundary scattering resulting from the trapping of free electrons due to oxygen adsorption on the grain boundary surface. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

ZnO半导体电导型X射线探测器件研究

本文制备了基于ZnO纳米线阵列和ZnO薄膜的Ag-ZnO-Ag电导型X射线探测器件,研究了它们对X射线的响应特性.薄膜器件在100 V偏置时的响应度达到0.12μC/Gy,纳米线阵列器件在50 V偏压下的响应度达到0.17μC/Gy.器件工作机理研究表明,器件的响应过程与表面氧吸附与解吸附效应有关,氧气吸附与解吸附过程使得X射线辐照下的载流子寿命大幅度增加,从而使得器件对X射线具有较高的响应度.本文研究结果表明ZnO薄膜和纳米线阵列器件在X射线剂量测量领域具有应用前景.     

钼掺杂氧化锌薄膜的结构、光学和表面等离子体特性研究

室温下,通过直流磁控反应溅射在石英衬底上制备一系列钼掺杂氧化锌薄膜。分别采用X射线衍射(XRD)、原子力显微镜(AFM)、分光光度计及拉曼光谱仪研究了钼掺杂浓度对氧化锌薄膜结构、表面形貌、光学性能和表面等离子体特性的影响。XRD测试结果表明,零掺杂氧化锌薄膜结晶良好,呈c轴择优取向,掺杂后薄膜缺陷增多,结晶质量下降,当掺杂浓度达到3.93 Wt%时,薄膜由c轴择优取向的晶态转变为非晶态。AFM测试结果表明非晶态掺钼氧化锌薄膜表面光滑,粗糙度最低可达489 pm。透射光谱表明所有薄膜样品在可见光范围(400～760 nm)平均透过率均达到80%,禁带宽度随着掺杂浓度的提高从3.28 eV单调增加至3.60 eV。吸收光谱表明氧化锌薄膜表面等离子体共振吸收峰随钼掺杂量的增大发生蓝移,而拉曼光谱表明Mo重掺杂时ZnO薄膜表面拉曼散射信号强度显著降低。通过Mo掺杂获得非晶态氧化锌薄膜,拓宽了氧化锌薄膜材料的应用领域,同时研究了Mo掺杂浓度对氧化锌薄膜表面等离子体的调控作用,这对制备氧化锌基光子器件具有重要参考价值。     

包埋Pt纳米粒子对金属-半导体-金属结构ZnO紫外光电探测器性能的影响

利用射频磁控溅射设备制备ZnO薄膜, 最终制备ZnO/Pt纳米粒子/ZnO 结构的金属-半导体-金属型紫外光电探测器. 研究了Pt纳米粒子处在ZnO薄膜层中的不同深度对金属-半导体-金属型紫外光电探测器响应性能的影响. 结果表明, 探测器的响应度随着Pt纳米粒子在ZnO薄膜层中所处深度的增大而升高. 在60 V偏压下, 包埋Pt最深的探测器在波长365 nm处取得响应度最大值1.4 A·W^-1, 包埋有Pt探测器的响应度最大值为无Pt 纳米粒子探测器响应度最大值的7倍. 结合对ZnO薄膜表面的表征及探测器各项性能的测试, 得出包埋Pt纳米粒子增强器件的响应性能可归因于表面等离子体增强散射.     

巯基丙酸分子对CdSe核壳量子点和 ZnO纳米粒子薄膜之间电荷转移的影响

通过稳态光谱和时间分辨荧光光谱研究了巯基丙酸(MPA)分子对由量子点到ZnO纳米粒子薄膜的电荷转移过程的影响。研究发现,相对于CdSe纳米粒子薄膜样品,没有MPA分子参与作用的CdSe/ZnO薄膜样品和有MPA分子连接的CdSe/MPA/ZnO薄膜样品中都存在从CdSe量子点到ZnO纳米粒子薄膜的有效电荷分离过程,但是相对于CdSe/ZnO样品, CdSe/MPA/ZnO样品中电荷转移速率明显变小。这表明MPA分子本身它并不能促进CdSe到ZnO电荷分离过程,因此可以认为用金属氧化物薄膜直接吸附量子点吸收材料,将能获得高功率转换效率的量子点敏化太阳能电池。     

用微波ECR等离子体溅射法在蓝宝石(0112)晶面上生长ZnO薄膜的研究

蓝宝石上外延生长ZnO薄膜在表面波和声光器件中有重要的应用．用微波电子回旋共振(ECR)等离子体溅射法在蓝宝石(0112)晶面上外延生长了ZnO薄膜,膜无色透明,并且表面光滑,基片温度为380℃,为探索沉积工艺参数对薄膜结构的影响,用XRD对不同基片温度和沉积速率生长的ZnO薄膜进行了研究．     

Low-threshold ZnO random lasing in a homojunction diode with embedded double heterostructure

An electrically pumped random laser diode was fabricated with a MgZnO/ZnO/MgZnO double heterostructure embedded in a ZnO pn junction. Gain can be achieved at very low-threshold current owing to exciton processes. Light closed loops are formed by random multiple scattering on vertical column boundaries in the thin film. The tilted and rough mesa edge planes serve as refraction mirrors, giving rise to surface emission.     

Optically and electrically pumped random lasing from ZnO films annealed at different temperatures

We have investigated the optically and electrically pumped random lasing (RL) actions in ZnO films annealed at low and high temperatures respectively. While the optically pumped RL threshold for the ZnO film annealed at a low temperature, which features stronger light scattering and larger optical loss, is far higher than that for the ZnO film annealed at a high temperature, the electrically pumped RL threshold currents for the two ZnO films are almost the same with the electrical pumping scheme of metal-insulator-semiconductor structure. It is suggested that if the lasing region within the ZnO film is narrow enough in the case of electrical pumping, the strong light scattering can substantially alleviate the adverse effect of large optical loss on the onset of RL.     

Chemical adsorption of C60 on diamond (100)(2×1) surfaces

Molecular-dynamics simulations (MDSs) and ab initiocalculations are used to investigate the adsorption behavior of C₆₀ molecules on a clean dimer-reconstructed (100)(2×1) diamond surface. C₆₀ molecules have some probability to be adsorbed on the diamond surface at low incident energy (6∼45 eV). Electron-density contours show strong chemical interaction between C₆₀ molecules and the substrate surface. The adsorption property depends strongly on the incident energy and the impacting point. An incident energy of 18 eV may be an appropriate energy to grow a sub-monolayer or monolayer C₆₀ film on a clean C(100)(2×1) surface at room temperature. Received: 5 July 2000 / Accepted: 17 October 2000 / Published online: 28 February 2001     

Laser-assisted local patterning of ZnO-based spots for mirror-less lasing

ZnO is known as one of the best materials for the implementation of the random lasing effect, associated with mirror-less laser emission in a simultaneously amplifying and highly scattering medium. Normally, the fabrication of this medium requires a rather complicated procedure of deposition and thermal treatment of ZnO-based films on some specific substrates, yielding wurtzite-orientation ZnO nanocrystals. We demonstrate a rapid synthesis of highly efficient ZnO-based random lasing spots on a piece of Zn by employing the phenomenon of laser-induced air breakdown. Being ignited near the surface of a Zn target, plasma of the air breakdown serves as a local reactor to locally transform its properties and thus form a film of well-packed 20–40 nm ZnO nanospheres. Exhibiting extremely high amplification and scattering, this medium is capable of generating the random lasing effect within the exciton-based photoluminescent band.     

电化学方法制备ZnO纳米颗粒掺杂类金刚石薄膜及其场发射性能研究

采用液相电化学沉积技术制备了ZnO纳米颗粒掺杂的类金刚石(DLC)薄膜, 研究了ZnO纳米颗粒掺杂对DLC薄膜场发射性能的影响. 利用X射线光电子能谱、透射电子显微镜、Raman光谱以及原子力显微镜分别对薄膜的化学组成、 微观结构和表面形貌进行了表征. 结果表明: 薄膜中的ZnO纳米颗粒具有纤锌矿结构, 其含量随着电解液中Zn源的增加而增加. ZnO纳米颗粒掺杂增强了DLC薄膜的石墨化和表面粗糙度. 场发射测试表明, ZnO纳米颗粒掺杂能提高DLC薄膜的场发射性能, 其中Zn与Zn+C的原子比为10.3%的样品在外加电场强度为20.7 V/μm时电流密度达到了1 mA/cm². 薄膜场发射性能的提高归因于ZnO掺杂引起的表面粗糙度和DLC薄膜石墨化程度的增加.     

Influence of substrate temperature on the optical and piezoelectric properties of ZnO thin films deposited by rf magnetron sputtering

In this study, ZnO thin films were fabricated using the rf magnetron sputtering method and their piezoelectrical and optical characteristics were investigated for various substrate temperatures. The ZnO thin film has the largest crystallization orientation for the (0 0 2) peak and the smallest FWHM value of 0.56° at a substrate temperature of 200 °C. The surface morphology shows a relatively dense surface structure at 200 °C compared to the other substrate temperatures. The surface roughness shows the smallest of 1.6 nm at a substrate temperature of 200 °C. The piezoelectric constant of the ZnO thin film measured using the pneumatic loading method (PLM) has a maximum value of 11.9 pC/N at a substrate temperature of 200 °C. The transmittance of the ZnO thin film measured using spectrophotometry with various substrate temperatures ranged from 75 to 93% in the visible light region. By fitting the refractive index from the transmittance to the Sellmeir dispersion relation, we can predict the refractive index of the ZnO thin film according to the wavelength. In the visible light range, the refraction index of the ZnO thin film deposited at a substrate temperature of 200 °C is the range of 1.88-2.08.     

Enhancement of the ultraviolet emission of ZnO nanorods by terphenyl liquid-crystalline ligands modification

We have developed a novel method to modifying the surface of ZnO nanorods (ZnO NRs) using p-hexoxyterphenylol (HTph-OH) as liquid crystal ligands. The structure and morphology of the modified ZnO NRs were characterized using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and atomic force microscopy (AFM). AFM measurement showed that the dispersion of ZnO NRs could be dramatically improved by the surface modification of HTph-OH and further annealing treatment at its liquid crystal state temperature (150 °C). The remarkable decrease of the annealed composite film roughness is because the HTph-OH chains self-organize into more ordered structure induced by mesogens after annealing treatment, which may push the ZnO NRs to form oriented nano-dispersing structure. The optical properties of the modified ZnO NRs were investigated by UV-vis absorption spectroscopy and photoluminescence spectroscopy (PL). Markedly enhanced band-edge ultraviolet photoluminescence and significantly reduced defect-related emission were observed. We attribute this observation to the nearly perfect surface passivation of the ZnO NRs by the HTph-OH molecules. Meanwhile, UV emission of modified ZnO NRs could be further enhanced by increasing the concentration of HTph-OH and annealing treatment at its liquid crystal state temperature.