Two-photon absorption of high-power picosecond pulses in PbWO<Subscript>4</Subscript>, ZnWO<Subscript>4</Subscript>, PbMoO<Subscript>4</Subscript>, and CaMoO<Subscript>4</Subscript> crystals

The nonlinear process of two-photon interband absorption is studied in tungstate and molybdate oxide crystals excited by a sequence of high-power picosecond pulses with a wavelength of 523.5 nm. The transmission of the crystals is measured for the excitation pulse intensity up to 100 GW/cm². The pulse intensity in the crystals initially transparent at a wavelength of 523.5 nm is strongly limited due to two-photon absorption (TPA), and the reciprocal transmission in PbWO₄ and ZnWO₄ crystals reaches 50–60. In all crystals, TPA induces long-lived one-photon absorption, which affects the nonlinear process dynamics and leads to a hysteresis in the dependence of the transmission on the laser excitation intensity. Absorption dichroism manifests itself in a significant difference in the transmission intensities when the principal orthogonal optical axes of the crystals are excited. The TPA coefficients are determined during the excitation of two optical axes of the crystals. TPA coefficients β for the crystals vary over a wide range, namely, from β = 2.4 cm/GW for PbMoO₄ to β = 0.14 cm/GW for CaMoO₄, and the values of β can differ almost threefold when different optical axes of a crystal are excited. Good agreement is achieved between the measured intensities limited by TPA and the estimates calculated from the measured nonlinear coefficients. Stimulated Raman scattering (SRS) upon excitation at a wavelength of 523.5 nm is only detected in two of the four crystals under study. The experimental results make it possible to explain the suppression of SRS by its competition with TPA, and the measured nonlinear coefficients are used to estimate this suppression.     

Raman spectroscopic study of structural disordering in YVO<Subscript>4</Subscript>, GdVO<Subscript>4</Subscript>, and CaWO<Subscript>4</Subscript> crystals

The Raman spectra of single-crystal YVO₄, GdVO₄, and ZrSiO₄ with a zircon structure, as well as CaWO₄ and BaWO₄ with a scheelite structure, are studied in detail over a wide temperature range 14–800 K. An inhomogeneous splitting of the A _1g (ν₂) vibrational lines in the Raman spectra of YVO₄ and GdVO₄ and the A _g (ν₁) vibrational lines in the spectrum of CaWO₄ is detected. It is shown that the profiles of these lines can be decomposed into two components, whose integrated intensities are redistributed with temperature and also depend on the matrix kind in which they are detected. The phenomenon observed is associated with the thermally activated processes of disorientation of the tetrahedral anions in the zircon and scheelite structures.     

Possibility of adjusting photoluminescence spectra of Ca scheelites (CaMoO<Subscript>4</Subscript>: Eu<Superscript>3+</Superscript> and CaWO<Subscript>4</Subscript>: Eu<Superscript>3+</Superscript>) to the emission spectrum of incandescent lamps

The peculiarities of the photoluminescence of compounds CaMoO₄: Eu³⁺ and CaWO₄: Eu³⁺ with the scheelite structure associated with a change in the short- and long-range orders of the crystal lattice upon a change in the activator (Eu³⁺) of the photoluminescence range in the interval 1–4 mol %, in which the photoluminescence of the matrix is preserved in the range 484–557 nm, are investigated using X-ray phase analysis as well as photoluminescence, Raman, and diffuse reflection spectroscopies. The introduction of Eu³⁺ ions leads to the reconstruction of the lattice so that up to 10% of these ions stimulate the formation of centrosymmetric localization upon the substitution of Ca²⁺ ions in the noncentrosymmetric positions. It is found that the spectral radiant emittance of the more effective luminophore CaMoO₄: Eu³⁺ can be adjusted to this parameter for an incandescent lamp for the Eu³⁺ concentration of 1–2 mol %.     

Synthesis of CaWO<Subscript>4</Subscript> nanocolloidal suspension via pulsed laser ablation and its optical properties

Pulsed laser ablation (PLA) in the liquid phase was successfully employed to synthesize calcium tungstate (CaWO₄) nanocolloidal suspension. The crystalline phase, particle morphology and laser ablation mechanism for the colloidal nanoparticles were investigated using XRD, TEM and SEM. The obtained colloidal suspension consisted of well-dispersed CaWO₄ nanoparticles which showed a spherical shape with sizes ranging from 5 to 30 nm. The laser ablation and the nanoparticle forming process were discussed under consideration of the photo-ablation mechanism, where the nanoparticles were generated by rapid condensation of the plume in high pressured ethanol vapor. The optical properties of the prepared CaWO₄ colloidal nanoparticles were analyzed in detail using XPS, Raman spectroscopy, UV-Vis spectroscopy and PL spectrophotometry. The optical band gap was estimated by Tauc and Menths law. PACS 42.62.-b; 82.70.Dd; 78.55.Hx; 81.07.Wx     

Temperature-dependent dispersion relations for RbTiOPO<Subscript>4</Subscript> and RbTiOAsO<Subscript>4</Subscript>

We have measured the first and second derivatives of the refractive index with respect to temperature along the z- and y-axes for two nonlinear optical materials, RbTiOPO₄ and RbTiOAsO₄. The measurements were done using an interferometric setup in the wavelength range of 532–1580 nm and in the temperature range of 25–200 °C. In addition, the thermal expansion coefficients were measured in the x direction. Experimental results of nonlinear frequency conversion in RbTiOAsO₄ were used to explore the temperature dependence of the refractive index in the z-axis near 3.5 microns. We have derived thermal-dependent dispersion equations for the two materials. Calculations based on these dispersion equations are in good agreement with previously reported measurements. The thermal dependence of the refractive index of RbTiOAsO₄ is greater than that of RbTiOPO₄ by approximately 15% and 70% in the z- and y-axes, respectively. Hence RbTiOPO₄ is more appropriate for applications that require immunity to thermal lensing, whereas RbTiOAsO₄ is suitable for realizing temperature-tuned nonlinear devices. PACS 42.65.Ki, 78.20.Cy, 78.20.Nv     

Preparation and electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Ti<Subscript>4</Subscript>O<Subscript>7</Subscript> composite for lithium-ion batteries

In order to improve the rate capability of Li₄Ti₅O₁₂, Ti₄O₇ powder was successfully fabricated by improved hydrogen reduction method, then a dual-phase composite Li₄Ti₅O₁₂/Ti₄O₇ has been synthesized as anode material for lithium-ion batteries. It is found that the Li₄Ti₅O₁₂/Ti₄O₇ composite shows higher reversible capacity and better rate capability compared to Li₄Ti₅O₁₂. According to the charge-discharge tests, the Li₄Ti₅O₁₂/Ti₄O₇ composite exhibits excellent rate capability of 172.3 mAh g^?1 at 0.2 C, which is close to the theoretical value of the spinel Li₄Ti₅O₁₂. More impressively, the reversible capacity of Li₄Ti₅O₁₂/Ti₄O₇ composite is 103.1 mAh g^?1 at the current density of 20 C after 100th cycles, and it maintains 84.8% of the initial discharge capacity, whereas that of the bare spinel Li₄Ti₅O₁₂ is only 22.3 mAh g^?1 with a capacity retention of 31.1%. The results indicate that Li₄Ti₅O₁₂/Ti₄O₇ composite could be a promising anode material with relative high capacity and good rate capability for lithium-ion batteries.     

Retardation of polarization in mixed K<Subscript>0.88</Subscript>(NH<Subscript>4</Subscript>)<Subscript>0.12</Subscript>H<Subscript>2</Subscript>PO<Subscript>4</Subscript> crystal

The time dependences of polarization of K_0.88(NH₄)_0.12H₂PO₄ mixed crystal have been studied within the temperature range of 74–100 K. Two mechanisms of polarization relaxation were found. The first mechanism is caused by domain walls lateral motion and their interaction with point lattice defects. The second one supposedly is due to polar regions infiltration through the regions of frustrated paraelectric phase.     

Electrical characterization of the [N(CH<Subscript>3</Subscript>)<Subscript>4</Subscript>][N(C<Subscript>2</Subscript>H<Subscript>5</Subscript>)<Subscript>4</Subscript>]ZnCl<Subscript>4</Subscript> compound

The [N(CH₃)₄][N(C₂H₅)₄]ZnCl₄ compound has been synthesized by a solution-based chemical method. The X-ray diffraction study at room temperature revealed an orthorhombic system with P2₁2₁2 space group. The complex impedance has been investigated in the temperature and frequency ranges 420–520 K and 200 Hz–5 MHz, respectively. The grain interior and grain boundary contribution to the electrical response in the material have been identified. Dielectric data were analyzed using the complex electrical modulus M ^* for the sample at various temperature. The modulus plots can be characterized by full width at half height or in terms of a non-exponential decay function ϕ(t) = exp[(−t/τ) ^β ]. The detailed conductivity study indicated that the electrical conduction in the material is a thermally activated process. The variation of the AC conductivity with frequency at different temperatures obeys the Almond and West universal law.     

Electronic excitations in BeAl<Subscript>2</Subscript>O<Subscript>4</Subscript>, Be<Subscript>2</Subscript>SiO<Subscript>4</Subscript>, and Be<Subscript>3</Subscript>Al<Subscript>2</Subscript>Si<Subscript>6</Subscript>O<Subscript>18</Subscript> crystals

Low-temperature (T = 7 K) time-resolved selectively photoexcited luminescence spectra (2–6 eV) and luminescence excitation spectra (8–35 eV) of wide-bandgap chrysoberyl BeAl₂O₄, phenacite Be₂SiO₄, and beryl Be₃Al₂Si₆O₁₈ crystals have been studied using time-resolved VUV spectroscopy. Both the intrinsic luminescence of the crystals and the luminescence associated with structural defects were assigned. Energy transfer to impurity luminescence centers in alexandrite and emerald was investigated. Luminescence characteristics of stable crystal lattice defects were probed by 3.6-MeV accelerated helium ion beams.     

Ferroelectric and dielectric properties of SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> thin films grown on Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> film layer

Ferroelectric and dielectric properties of bilayered ferroelectric thin films, SrBi₄Ti₄O₁₅ grown on Bi₄Ti₃O₁₂, were investigated. The thin films were annealed at 700°C under oxygen atmosphere. The bilayered thin films were prepared on a Pt(111)/Ti/SiO₂/Si substrate by a chemical solution deposition method. The dielectric constant and dielectric loss of the bilayered thin films were 645 and 0.09, respectively, at 100 kHz. The value of remnant polarization (2P _r) measured from the ferroelectric thin film capacitors was 60.5 μC/cm² at electric field of 200 kV/cm. The remnant polarization was reduced by 22% of the initial value after 10¹⁰ switching cycles. The results showed that the ferroelectric and dielectric properties of the SrBi₄Ti₄O₁₅ on Bi₄Ti₃O₁₂ ferroelectric thin films were better than those of the SrBi₄Ti₄O₁₅ grown on a Pt-coated Si substrate suggesting that the improved properties may be due to the different nucleation and growth kinetics of SrBi₄Ti₄O₁₅ on the c-axis-oriented Bi₄Ti₃O₁₂ layer or on the Pt-coated Si substrate.     

X-ray study of [N(CH<Subscript>3</Subscript>)<Subscript>4</Subscript>]<Subscript>2</Subscript>ZnCl<Subscript>4</Subscript> at low temperatures

The unit cell parameters a, b, and c of [N(CH₃)₄]₂ZnCl₄ have been measured by x-ray diffraction in the temperature range 80–293 K. Temperature dependences of the thermal expansion coefficients α_a, α_b, and α_c along the principal crystallographic axes and of the unit cell thermal expansion coefficient α_V were determined. It is shown that the a=f(T), b=f(T), and c=f(T) curves exhibit anomalies in the form of jumps at phase transition temperatures T₁=161 K and T₂=181 K and that the phase transition occurring at T₃=276 K manifests itself in the a=f(T) and b=f(T) curves as a break. A slight anisotropy in the coefficient of thermal expansion of the crystal was revealed. The phase transitions occurring at T₁=161 K and T₂=181 K in [N(CH₃)₄]₂ZnCl₄ were established to be first-order.     

Quantum oscillations in dual-layered quasi-two-dimensional organic metal (ET)<Subscript>4</Subscript>HgBr<Subscript>4</Subscript>(C<Subscript>6</Subscript>H<Subscript>4</Subscript>Cl<Subscript>2</Subscript>)

We study the effect of interionic anisotropy on the phase states of a non-Heisenberg ferromagnet with magnetic ion spin S = 1. It is shown that depending on the relation between the interionic anisotropy constants, uniaxial and angular ferromagnetic and nonmagnetic phases exist in the system. We analyze the dynamic properties of the system in the vicinity of orientational phase transitions, as well as a phase transition in the magnetic moment magnitude. It is shown that orientational phase transitions in ferromagnetic and nematic phases can be first- as well as second-order.     

Effect of pressure on the structure and the electronic properties of LiClO4, NaClO<Subscript>4</Subscript>, KClO<Subscript>4</Subscript>, and NH<Subscript>4</Subscript>ClO<Subscript>4</Subscript>

The effect of pressure on the structural and electronic properties of lithium, sodium, potassium, and ammonium perchlorates have been studied in terms of the density functional theory with allowance for the Van der Waals dispersion interaction. The pressure dependences of the geometric parameters, the band gaps, the densities of states, the charge distributions, and the atomic charges are calculated. The compressibilities of the perchlorates are found to be anisotropic, which is due to the differences of the lattice parameters and the nature of interatomic bonds. Ammonium cation is rotated under pressure around axis b at an angle of ~9°. The band gaps of the perchlorates are ~4.5–4.7 eV and increase with pressure.     

Raman and FTIR spectroscopy study of LiFeTiO<Subscript>4</Subscript> and Li<Subscript>2</Subscript>FeTiO<Subscript>4</Subscript>

We report the Fourier transform infrared (FTIR)–Raman spectroscopy study of spinel Li–Fe–Ti–O oxides viz., LiFeTiO₄ and Li₂FeTiO₄ in order to probe structural details such as type of bonding networks viz., octahedral and tetrahedral, and type of different atomic bonds present in those materials. Both the samples were prepared through solid-state reaction route prior to high-energy ball-milling. All the phases prepared through solid-state reaction and ball-milled were probed using X-ray diffraction, field emission scanning electron microscopy, and FTIR–Raman spectroscopy. X-ray diffraction study indicates spinel phase formation with Fd3m space group symmetry for both LiFeTiO₄ and Li₂FeTiO₄. However, pure phase of Li₂FeTiO₄ was not achieved in these preparation routes, rather mixed phases of Li₂FeTiO₄ and Fe₂TiO₄ were achieved. Field emission scanning electron microscopy (FESEM) analysis indicated porous microstructure for LiFeTiO₄ while more agglomerated microstructure for Li₂FeTiO₄. Ball-milling reduces the grain size partly for both the samples. FTIR–Raman spectroscopy indicates the presence of LiO₄ tetrahedral, LiO₆ and TiO₆ octahedral in the spinel network. Presence of Li–Li–O type bonding was also indicated from spectroscopy analysis. Existence of Fe₂TiO₄ phase with Li₂FeTiO₄ was also identified from both FTIR and Raman spectrum. Effect of ball-milling on the spectrum has been exhibited by broadening and peak shifting the FTIR–Raman spectrum, arising from the enhanced lattice strain and structural disorder.     

Refractometry of mechanically compressed (NH<Subscript>4</Subscript>)<Subscript>2</Subscript>SO<Subscript>4</Subscript> crystals

The effect of uniaxial mechanical pressure σ _m ≤ 150 bar on the spectral (300–800 nm) dependence of the birefringerence Δn _i and refractive indices n _i of (NH₄)₂SO₄ crystals has been investigated. It is shown that the dispersion of n _i (λ) and Δn _i (λ) is normal and sharply increases with approach to the absorption edge. It is established that uniaxial pressure does not change the character of the dispersions dn _i /dλ and dΔn _i /dλ and only affects their magnitudes. It is shown that the increase in the refractive indices under uniaxial stress is mainly due to the increase in the refraction caused by the increase in the band gap and long-wavelength shift of the UV absorption band maximum.     

Synthesis,thermal and electrical behavior of the superprotonic conductor phase in Rb<Subscript>3</Subscript>(HSeO<Subscript>4</Subscript>)<Subscript>2.5</Subscript>(H<Subscript>2</Subscript>PO<Subscript>4</Subscript>)<Subscript>0.5</Subscript> compound

The Rb₃(HSeO₄)_2.5(H₂PO₄)_0.5 compound was prepared and its thermal behavior and electric properties were investigated. The thermogravimetry (TGA) analysis and the differential scanning calorimetric (DSC) show the presence of a structural phase transition of the title compounds at 374 K which is confirmed by the variation of fp and σ_dc as a function of temperature. The complex impedance of the Rb₃(HSeO₄)_2.5(H₂PO₄)_0.5 compound has been investigated in the temperature range of 295–453 K and in the frequency range 209 Hz–1 MHz. The impedance plots show semicircle arcs at different temperatures, and an electrical equivalent circuit has been proposed to explain the impedance results. The circuits consist of the parallel combination of bulk resistance Rp and constant phase elements CPE₁ in series with fractal capacity CPE₂. The frequency dependence of the conductivity is interpreted in terms of Jonscher’s law. The conductivity dc follows the Arrhenius relation. The near value of activation energies obtained from the analysis of modulus, conductivity data, and circuit equivalent confirm that the transport is through the ion hopping mechanism, dominated by the motion of the H⁺ proton in the structure of the investigated materials.     

Comparative Study of the Magnetoelectric Effect in HoAl<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript> and HoGa<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript> Single Crystals

The comparative study of the magnetoelectric properties and magnetostriction of HoGa₃(BO₃)₄ and HoAl₃(BO₃)₄ single crystals has been carried out. The investigated compounds exhibit qualitatively similar magnetodielectric and inverse magnetoelectric ME _E effects with the close absolute values, which is indicative of the weak effect of a nonmagnetic metal ion. On the contrary, the magnetostriction of the galloborate has been found to be threefold higher than that of the alumoborate. In addition, the difference between the qualitative behaviors of magnetostriction has been established: the magnetic-field dependence of magnetostriction for the alumoborate has the maximum near 70 kOe at T = 4.2 K, while the galloborate magnetostriction has no maximum and does not saturate in a field of 140 kOe.     

Entanglement in the linear-chain Heisenberg antiferromagnet Cu(C<Subscript>4</Subscript>H<Subscript>4</Subscript>N<Subscript>2</Subscript>)(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>

Quantum correlations are generally impossible to address directly in bulk systems. Quantum measures extended only to a few number of parties can be discussed in practice. In the present work we study a cluster of spins belonging to a compound whose structure is that of a quantum magnet. We reproduce at a much smaller scale the experimental outcomes and then we study the role of quantum correlations there. A macroscopic entanglement witness has been introduced in order to reveal quantum correlations at nonzero temperatures. The critical point beyond which entanglement is zero is found at T _c = 15 K.     

Electrochemical comparison of LiFe<Subscript>0.4</Subscript>Mn<Subscript>0.595</Subscript>Cr<Subscript>0.005</Subscript>PO<Subscript>4</Subscript>/C and LiMnPO<Subscript>4</Subscript>/C cathode materials

A comparison of electrochemical performance between LiFe_0.4Mn_0.595Cr_0.005PO₄/C and LiMnPO₄/C cathode materials was conducted in this paper. The cathode samples were synthesized by a nano-milling-assisted solid-state process using caramel as carbon sources. The prepared samples were investigated by XRD, SEM, TEM, energy-dispersive X-ray spectroscopy (EDAX), powder conductivity test (PCT), carbon-sulfur analysis, electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge cycling. The results showed that LiFe_0.4Mn_0.595Cr_0.005PO₄/C exhibited high specific capacity and high energy density. The initial discharge capacity of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 163.6 mAh g^?1 at 0.1C (1C = 160 mA g^?1), compared to 112.3 mAh g^?1 for LiMnPO₄/C. Moreover, the Fe/Cr-substituted sample showed good cycle stability and rate performance. The capacity retention of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 98.84 % over 100 charge-discharge cycles, while it was only 86.64 % for the pristine LiMnPO₄/C. These results indicated that Fe/Cr substitution enhanced the electronic conductivity for the prepared sample and facilitated the Li⁺ diffusion in the structure. Furthermore, LiFe_0.4Mn_0.595Cr_0.005PO₄/C composite presented high energy density (606 Wh kg^?1) and high power density (574 W kg^?1), thus suggested great potential application in lithium ion batteries (LIBs).     

Electronic spectra and phase transitions in thin [N(CH<Subscript>3</Subscript>)<Subscript>4</Subscript>]<Subscript>2</Subscript>CuCl<Subscript>4</Subscript> microcrystals

Optical absorption spectra in thin [N(CH₃)₄]₂CuCl₄ crystals in the thickness range 10 μm ≤ d < 100 μm have been studied. Strengthening of the crystal field has been found with a decrease in the [N(CH₃)₄]₂CuCl₄ crystal size. The reasons for absorption band shifts in the visible region depending on the [N(CH₃)₄]₂CuCl₄ crystal thickness and the manifestation of a size effect in crystals with an incommensurate superstructure are discussed.