Stabilized flames in hybrid aluminum-methane-air mixtures

A premixed methane–air bunsen-type flame is seeded with micron-sized (d₃₂ = 5.6 μm) atomized aluminum powder over a wide range of solid fuel concentrations. The burning velocities of the resulting two-phase hybrid flame are determined using the total surface area of the inner flame cone and the known volumetric flow rate, and spatially resolved flame spectra are obtained with a spectral scanning system. Flame temperatures are derived through polychromatic fitting of Planck’s law to the continuous part of the spectrum. It is found that an increase in the solid fuel concentration changes the aluminum combustion regime from low temperature oxidation to full-fledged flame front propagation. For stoichiometric methane–air mixtures, the transition occurs in the aluminum concentration range of 140–220 g/m³ and is manifested by the appearance of AlO sub-oxide bands and an increase in the flame temperature to 2500 K. The flame burning velocity is found to decrease only slightly with an increase in aluminum concentration, in contrast to the rapid decrease in flame speed, followed by quenching, that is observed for flames seeded with inert SiC particles. The observed behavior of the burning velocity and flame temperature leads to the conclusion that intense aluminum combustion in a hybrid flame only occurs when the flame front propagating through the aluminum suspension is coupled to the methane–air flame.     

Dynamics of triple-flames in ignition of turbulent dual fuel mixture: A direct numerical simulation study

Pilot-ignited dual fuel combustion involves a complex transition between the pilot fuel autoignition and the premixed-like phase of combustion, which is challenging for experimental measurement and numerical modelling, and not sufficiently explored. To further understand the fundamentals of the dual fuel ignition processes, the transient ignition and subsequent flame development in a turbulent dimethyl ether (DME)/methane-air mixing layer under diesel engine-relevant conditions are studied by direct numerical simulations (DNS). Results indicate that combustion is initiated by a two-stage autoignition that involves both low-temperature and high-temperature chemistry. The first stage autoignition is initiated at the stoichiometric mixture, and then the ignition front propagates against the mixture fraction gradient into rich mixtures and eventually forms a diffusively-supported cool flame. The second stage ignition kernels are spatially distributed around the most reactive mixture fraction with a low scalar dissipation rate. Multiple triple flames are established and propagate along the stoichiometric mixture, which is proven to play an essential role in the flame developing process. The edge flames gradually get close to each other with their branches eventually connected. It is the leading lean premixed branch that initiates the steady propagating methane-air flame. The time required for the initiation of steady flame is substantially shorter than the autoignition delay time of the methane-air mixture under the same thermochemical condition. Temporal evolution of the displacement speed at the flame front is also investigated to clarify the propagation characteristics of the combustion waves. Cool flame and propagation of triple flames are also identified in this study, which are novel features of the pilot-ignited dual fuel combustion.     

Stabilized,flat iron flames on a hot counterflow burner

Metal powder combustion has traditionally been studied to mitigate the risk of industrial accidents and to determine the contributions of metals as additives to the performance of energetic materials. Recently, there has been growing interest in exploring the potential of metal powders as recyclable, zero-carbon energy carriers as an alternative to the hydrocarbons known to contribute to climate change. The present work introduces, for the first time, a stabilized flat iron flame. The counterflow burner used in this work is comprised of an inverted ceramic nozzle which sits above, and is aligned axially with, a lower nozzle producing a laminar flow of particles suspended in an oxidizing gas. A stabilized methane flame sits inside the top nozzle and the hot combustion products impinge upon the two-phase flow from the bottom nozzle, creating a stagnation plane. Spherical iron powder, with 90% of the particles less than 2.5 µm in size, is pre-loaded into a piston and dispersed using mixtures of 30% and 40% oxygen balanced in argon. Flame speeds are measured using particle image velocimetry (PIV), while flame temperatures are determined using multicolour pyrometry. It is found that flame speeds range between 30 cm/s and 45 cm/s for both oxidizing mixtures. Despite having fuel loadings below stoichiometric concentrations, the observed particle combustion temperatures are close to the adiabatic flame temperature of the stoichiometric mixture, indicating combustion in the diffusion-controlled regime for these small particles. Finally, the independence of the flame speeds with respect to oxygen concentration suggests flame propagation in the discrete regime.     

Spherical turbulent flame propagation of pulverized coal particle clouds in an O2/N2 atmosphere

The present study aims to clarify the effects of turbulence intensity and coal concentration on the spherical turbulent flame propagation of a pulverized coal particle cloud. A unique experimental apparatus was developed in which coal particles can be dispersed homogeneously in a turbulent flow field generated by two fans. Experiments on spherical turbulent flame propagation of pulverized coal particle clouds in a constant volume spherical chamber in various turbulence intensities and coal concentrations were conducted. A common bituminous coal was used in the present study. The flame propagation velocity was obtained from an analysis of flame propagation images taken using a high-speed camera. It was found that the flame propagation velocity increased with increasing flame radius. The flame propagation velocity increases as the turbulence intensity increases. Similar trends were observed in spherical flames using gaseous fuel. The coal concentration has a weak effect on the flame propagation velocity, which is unique to pulverized coal combustions in a turbulent field. These are the first reports of experimental results for the spherical turbulent flame propagation behavior of pulverized coal particle clouds. The results obtained in the present study are obviously different from those of previous pulverized coal combustion studies and any other results of gaseous fuel combustion research.     

Determination of Soot Particle Size in a Premixed Flame: a Static and Dynamic Light Scattering Study

In this contribution we report upon our static and dynamic light scattering experiments to characterize soot particles in flames. We studied sooting laminar premixed flame with acetylene as fuel mixed with air as oxidizer. The air equivalence ratio of the combustion was larger than one. We used a Kaskan type burner with circular geometry and a stabilizing flow of nitrogen around the flame. We focused on the determination of the size of the soot particles in the center of the flame as a function of height above burner. In addition we investigated the influence of the mixing ratio of the gases on the size of the particles. Our results show that static light scattering is better suited than dynamic light scattering for a fast and reliable characterization of soot particles in flames. The latter needs detailed a priori information about the flame to allow the unique determination of sizes from the diffusion measurements. The soot particles grow monotonously with height above burner and with decreasing air equivalence ratio. The aggregates have a fractal dimension lower than two.     

Emission spectroscopy of flame fronts in aluminum suspensions

Spatially resolved emission spectra from Bunsen-type flames stabilized in aluminum suspensions in air and oxygen–argon/helium mixtures were obtained using a mechanical-optical scanning system. A low resolution (1.5 nm) spectrometer was used to acquire the broad spectra over the 350–1000 nm range, and a high-resolution (0.04 nm) instrument was used for observation of AlO molecular bands and non-ionized atomic aluminum. The temperature of condensed phase emitters in the flame was derived using polychromatic fitting of the continuum spectra to Planck’s law. AlO temperature was found by fitting of the theoretically calculated shape of the band to experimental data. Peak temperatures of the condensed emitters were found to be approximately 3250 K in aluminum-air flames and approximately 3350 K for oxygen–argon/helium flames. Temperatures derived from AlO spectra coincide with the temperature of the condensed emitters with measurement accuracy and are only 100–200 °C lower than the computed equilibrium flame temperatures. The radial distribution of the temperature profile of the continuous emitters was found via Abel deconvolution and recovered the double-front structure of the Bunsen flame cone, with the outer flame being attributed to a diffusion flame of the fuel-rich products with ambient air. The observation of atomic aluminum lines seen in emission from the outer flame edge and partial self-absorption from the inner flame confirms the structure associated with the double-front structure. The implications of these results for the regime of particle combustion in a dust flame are discussed.     

Ignition and volatile combustion behaviors of a single lignite particle in a fluidized bed under O2/H2O condition

O₂/H₂O combustion, as a new evolution of oxy-fuel combustion, has gradually gained more attention recently for carbon capture in a coal-fired power plant. The physical and chemical properties of steam e.g. reactivity, thermal capacity, diffusivity, can affect the coal combustion process. In this work, the ignition and volatile combustion characteristics of a single lignite particle were first investigated in a fluidized bed combustor under O₂/H₂O atmosphere. The flame and particle temperatures were measured by a calibrated two-color pyrometry and pre-buried thermocouple, respectively. Results indicated that the volatile flame became smaller and brighter as the oxygen concentration increased. The ignition delay time of particle in dense phase was shorter than that in dilute phase due to its higher heat transfer coefficient. Also, the volatile flame was completely separated from particles (defined as off-flame) in dense phase while the flame lay on the particle surface (defined as on-flame) in dilute phase. The self-heating of fuel particles by on-flame in dilute phase was more obvious than that in dense phase, leading to earlier char combustion. At low oxygen concentration, the flame in the H₂O atmosphere was darker than that in the N₂ atmosphere because the heat capacity of H₂O is higher than that of N₂. With the increase of oxygen concentration, the flame temperature in the O₂/H₂O atmosphere was dramatically enhanced rather than that in the O₂/N₂ atmosphere, where the diffusion rate of oxygen in O₂/N₂ atmosphere became the dominant factor.     

On the oscillating flame characteristics in nonpremixed laminar coflow-jets: An experimental and numerical study

This study investigates the characteristics of oscillating lifted flames in laminar coflow-jets experimentally and numerically by varying both fuel density (by varying propane and n-butane mixtures) and coflow density (by diluting air with N₂/He mixtures). Two different lifted flame oscillation behaviors are observed depending on these parameters: oscillating tribrachial lifted flame (OTLF) and oscillating mode-change lifted flame (OMLF), where a rapid increase in flame radius is observed. The regimes of the two flames are identified from experiments, which shows that OMLF occurs only when the effect of the negative buoyancy on the flow field by the fuel heavier than air becomes significant at low fuel jet velocity. OMLFs are also identified to distinguish OTLF regime from flame extinction, which implies that an OMLF can be extinguished when the positive buoyancy becomes weak, losing its stabilizing effect, or when the negative buoyancy becomes strong, further enhancing its destabilizing effect. Transient numerical simulations of both OTLF and OMLF reveal that the OMLF occurs by a strong toroidal vortex and a subsequent counterflow-like structure induced by relatively-strong negative buoyancy. Such a drastic flow redirection significantly changes the fuel concentration gradient such that the OMLF changes its mode from a tribrachial flame mode (decreasing edge speed with fuel concentration gradient) to the premixed flame-like transition mode when the fuel concentration gradient becomes very small (increasing edge speed with fuel concentration gradient). Again, a tribrachial flame mode is recovered during a rising period of flame edge and repeats an oscillation cycle.     

Modes of particle combustion in iron dust flames

The so-called argon/helium test is proposed to identify the combustion mode of particles in iron dust flames. Iron powders of different particle sizes varying from 3 to 34 μm were dispersed in simulated air compositions where nitrogen was replaced by argon and helium. Due to the independence of the particle burning rate on the oxygen diffusivity in the kinetic mode, the ratio between the flame speeds in helium and argon mixtures is expected to be smaller if the particle burning rate is controlled by reaction kinetics rather than oxygen diffusion. Experiments were performed in a reduced-gravity environment on a parabolic flight aircraft to prevent particle settling and buoyancy-driven disruption of the flame. Uniform suspensions of the iron powders were produced inside glass tubes and a flame was initiated at the open end of the tube. Quenching plate assemblies of various channel widths were installed inside the tube and pass or quench events were used to measure the quenching distance. Flame propagation was recorded by a high-speed digital camera and spectral measurements were used to determine the temperature of the condensed emitters in the flame. The measured flame speeds and quenching distances were in good agreement with previously developed one-dimensional, dust flame model where the particles are assumed to burn in a diffusive mode and heat losses are described on a volumetric basis. However, a significant drop of the ratio of flame speeds in helium and argon mixtures was observed for finer 3 μm particles and was attributed to a transition from the combustion controlled by diffusion for larger particles to kinetically controlled burning of micron-size particles. In helium mixtures, the lower flame temperatures measured in suspensions of fine particles in comparison to larger particles reinforces this assumption.     

Structure of propagating edge diffusion flames in hydrocarbon fuel jets

Direct numerical simulations with a C₃-chemistry model have been performed to investigate the transient behavior and internal structure of flames propagating in an axisymmetric fuel jet of methane, ethane, ethylene, acetylene, or propane in normal earth gravity (1g) and zero gravity (0g). The fuel issued from a 3-mm-i.d. tube into quasi-quiescent air for a fixed mixing time of 0.3 s before it was ignited along the centerline where the fuel–air mixture was at stoichiometry. The edge of the flame formed a vigorously burning peak reactivity spot, i.e., reaction kernel, and propagated through a flammable mixture layer, leaving behind a trailing diffusion flame. The reaction kernel broadened laterally across the flammable mixture layer and possessed characteristics of premixed flames in the direction of propagation and unique flame structure in the transverse direction. The reaction kernel grew wings on both fuel and air sides to form a triple-flame-like structure, particularly for ethylene and acetylene, whereas for alkanes, the fuel-rich wing tended to merge with the main diffusion flame zone, particularly methane. The topology of edge diffusion flames depend on the properties of fuels, particularly the rich flammability limit, and the mechanistic oxidation pathways. The transit velocity of edge diffusion flames, determined from a time series of calculated temperature field, equaled to the measured laminar flame speed of the stoichiometric fuel–air mixtures, available in the literature, independent of the gravity level.     

Effect of non-zero relative velocity on the flame speed of two-phase laminar flames

A numerical study of one-dimensional n-heptane/air spray flames is presented. The objective is to evaluate the flame propagation speed in the case where droplets evaporate inside the reaction zone with possibly non-zero relative velocity. A Direct Numerical Simulation approach for the gaseous phase is coupled to a discrete particle Lagrangian formalism for the dispersed phase. A global two-step n-heptane/air chemical mechanism is used. The effects of initial droplet diameter, overall equivalence ratio, liquid loading and relative velocity between gaseous and liquid phases on the laminar spray flame speed and structure are studied. For lean premixed cases, it is found that the laminar flame speed decreases with increasing initial droplet diameter and relative velocity. On the contrary, rich premixed cases show a range of diameters for which the flame speed is enhanced compared to the corresponding purely gaseous flame. Finally, spray flames controlled by evaporation always have lower flame speeds. To highlight the controlling parameters of spray flame speed, approximate analytical expressions are proposed, which give the correct trends of the spray flame propagation speed behavior for both lean and rich mixtures.     

镁颗粒群着火和燃烧过程数值模拟

建立了一维非稳态球形镁颗粒群的着火燃烧模型, 数值模拟镁颗粒群的着火和燃烧过程, 研究表明, 颗粒群着火首先发生在颗粒群边界, 随后初始的燃烧火焰会分离为两个, 一个向颗粒群内部传播, 一个向外部传播, 最终内部火焰消失, 外部火焰维持并控制着整个颗粒群的燃烧; 内火焰向颗粒群内部传播过程中, 传播速度会逐渐加快, 且火焰温度值呈逐渐降低趋势. 分析了颗粒群内部参数和环境参数对镁颗粒群着火燃烧的影响. 随颗粒浓度的增大, 颗粒群着火时间略有增长, 但火焰传播速度更快, 燃烧稳定时火焰球尺寸也更大. 颗粒群初温越高, 则颗粒群着火时间越短, 火焰传播速度也会加快, 但燃烧稳定时火焰球尺寸基本不变. 环境温度对颗粒群着火燃烧的影响较复杂, 环境温度越高, 颗粒群着火时间越短, 但火焰传播速度却越慢, 燃烧稳定时火焰球尺寸变化很小. 颗粒粒径和辐射源温度对颗粒群着火燃烧的影响较显著, 颗粒粒径越小或辐射源温度越高, 则颗粒群着火时间越短, 火焰传播速度越快, 燃烧稳定时火焰球尺寸也越大. 数值模拟结果与文献中试验结果相一致. 关键词： 粉末燃料冲压发动机 镁着火燃烧 颗粒群     

Premixed flame response to equivalence ratio perturbations

This paper studies the heat-release oscillation response of premixed flames to oscillations in reactant stream fuel/air ratio. Prior analyses have studied this problem in the linear regime and have shown that heat release dynamics are controlled by the superposition of three processes: flame speed, heat of reaction, and flame surface area oscillations. Each contribution has somewhat different dynamics, leading to complex frequency and mean fuel/air ratio dependencies. The present work extends these analyses to include stretch and non quasi-steady effects on the linear flame dynamics, as well as analysis of nonlinearities in flame response characteristics. Because the flame response is controlled by a superposition of multiple processes, each with a highly nonlinear dependence upon fuel/air ratio, the results are quite rich and the key nonlinearity mechanism varies with mean fuel/air ratio, frequency, and amplitude of excitation. In the quasi-steady framework, two key mechanisms leading to heat-release saturation have been identified. The first of these is the flame-kinematic mechanism, previously studied in the context of premixed flame response to flow oscillations and recently highlighted by Birbaud et al. (Combustion and Flame 154 (2008), 356–367). This mechanism arises due to fluctuations in flame position associated with the oscillations in flame speed. The second mechanism is due to the intrinsically nonlinear dependence of flame speed and mixture heat of reaction upon fuel/air ratio oscillations. This second mechanism is particularly dominant at perturbation amplitudes that cause the instantaneous stoichiometry to oscillate between lean and rich values, thereby causing non-monotonic variation of local flame speed and heat of reaction with equivalence ratio.     

An assessment of large eddy simulations of premixed flames propagating past repeated obstacles

This paper presents an assessment of Large Eddy Simulations (LES) in calculating the structure of turbulent premixed flames propagating past solid obstacles. One objective of the present study is to evaluate the LES simulations and identify the drawbacks in accounting the chemical reaction rate. Another objective is to analyse the flame structure and to calculate flame speed, generated overpressure at different time intervals following ignition of a stoichiometric propane/air mixture. The combustion chamber has built-in repeated solid obstructions to enhance the turbulence level and hence increase the flame propagating speed. Various numerical tests have also been carried out to determine the regimes of combustion at different stages of the flame propagation. These have been identified from the calculated results for the flow and flame characteristic parameters. It is found that the flame lies within the ‘thin reaction zone’ regime which supports the use of the laminar flamelet approach for modelling turbulent premixed flames. A submodel to calculate the model coefficient in the algebraic flame surface density model is implemented and examined. It is found that the LES predictions are slightly improved owing to the calculation of model coefficient by using submodel. Results are presented and discussed in this paper are for the flame structure, position, speed, generated pressure and the regimes of combustion during all stages of flame propagation from ignition to venting. The calculated results are validated against available experimental data.     

Evaluation of models for flame stretch due to curvature in the thin reaction zones regime

Direct numerical simulation (DNS) was used to study modelling assumptions for the curvature-propagation component of flame stretch in the thin reaction zones regime of turbulent premixed combustion, a regime in which small eddies can penetrate the preheat zone but not the thinner fuel breakdown zone. Simulations of lean hydrogen–air and methane–air flames were conducted, and statistics of flame stretch due to curvature, henceforth referred to simply as stretch, were extracted from a species mass fraction iso-surface taken to represent the flame. The study focussed on investigating the modelling assumptions of Peters [J. Fluid Mech. 384 (1999) 107]. It was found that the mean stretch is dominated by stretch due to correlations of flame speed with curvature, and specifically the effects of tangential diffusion. The modelling suggestions of Peters were found to provide an improvement over the assumptions of a constant flame speed or a flame speed governed by the linear relationship with stretch at small and steady stretch. However for the conditions considered here, diffusive-thermal effects remain well into the thin reaction zones regime, and the suggestions of Peters generally over-predict the mean compressive stretch. An effective diffusivity for flame stretch was suggested and evaluated for the methane simulations. It was found that the effective diffusivity was comparable to the mass diffusivity for flames with a high ratio of flame time to eddy turnover time. The length scales contributing to stretch were investigated, and it was found that while most flame area has a radius of curvature greater than the laminar flame thickness, most stretch occurs in more tightly curved flame elements.     

Premixed turbulent flame front structure investigation by Rayleigh scattering in the thin reaction zone regime

Premixed turbulent flames of methane–air and propane–air stabilized on a bunsen type burner were studied using planar Rayleigh scattering and particle image velocimetry. The fuel–air equivalence ratio range was from lean 0.6 to stoichiometric for methane flames, and from 0.7 to stoichiometric for propane flames. The non-dimensional turbulence rms velocity, u′/S_L, covered a range from 3 to 24, corresponding to conditions of corrugated flamelets and thin reaction zones regimes. Flame front thickness increased slightly with increasing non-dimensional turbulence rms velocity in both methane and propane flames, although the flame thickening was more prominent in propane flames. The probability density function of curvature showed a Gaussian-like distribution at all turbulence intensities in both methane and propane flames, at all sections of the flame.The value of the term Dκ, the product of molecular diffusivity evaluated at reaction zone conditions and the flame front curvature, has been shown to be smaller than the magnitude of the laminar burning velocity. This finding questions the validity of extending the level set formulation, developed for corrugated flames region, into the thin reaction zone regime by increasing the local flame propagation by adding the term Dκ to laminar burning velocity.     

Lean or ultra-lean stretched planar methane/air flames

Lean premixed combustion has potential advantages of reducing pollutants and improving fuel economy. In some lean engine concepts, the fuel is directly injected into the combustion chamber resulting in a distribution of lean fuel/air mixtures. In this case, very lean mixtures can burn when supported by hot products from more strongly burning flames. This study examines the downstream interaction of opposed jets of a lean-limit CH₄/air mixture vs. a lean H₂/air flame. The CH₄ mixtures are near or below the lean flammability limit. The flame composition is measured by laser-induced Raman scattering and is compared to numerical simulations with detailed chemistry and molecular transport including the Soret effect. Several sub-limit lean CH₄/air flames supported by the products from the lean H₂/air flame are studied, and a small amount of CO₂ product (around 1% mole fraction) is formed in a “negative flame speed” flame where the weak CH₄/air mixture diffuses across the stagnation plane into the hot products from the H₂/air flame. Raman scattering measurements of temperature and species concentration are compared to detailed simulations using GRI-3.0, C₁, and C₂ chemical kinetic mechanisms, with good agreement obtained in the lean-limit or sub-limit flames. Stronger self-propagating CH₄/air mixtures result in a much higher concentration of product (around 6% CO₂ mole fraction), and the simulation results are sensitive to the specific chemical mechanism. These model-data comparisons for stronger CH₄/air flames improve when using either the C₂ or the Williams mechanisms.     

Transported PDF simulation of turbulent CH4/H2 flames under MILD conditions with particle-level sensitivity analysis

Transported probability density function (TPDF) simulation with sensitivity analysis has been conducted for turbulent non-premixed CH₄/H₂ flames of the jet-into-hot-coflow (JHC) burner, which is a typical model to emulate moderate or intense low oxygen dilution combustion (MILD). Specifically, two cases with different levels of oxygen in the coflow stream, namely HM1 and HM3, are simulated to reveal the differences between MILD and hot-temperature combustion. The TPDF simulation well predicts the temperature and species distributions including those of OH, CO and NO for both cases with a 25-species mechanism. The reduced reaction activity in HM1 as reflected in the peak OH concentration is well correlated to the reduced oxygen in the coflow stream. The particle-level local sensitivities with respect to mixing and chemical reaction further show dramatic differences in the flame characteristics. HM1 is less sensitive to mixing and reaction parameters than HM3 due to the suppressed combustion process. Specifically, for HM1 the sensitivities to mixing and chemical reactions have comparable magnitude, indicating that the combustion progress is controlled by both mixing and reaction in MILD combustion. For HM3, there is however a change in the combustion mode: during the flame initialization, the combustion progress is more sensitive to chemical reactions, indicating that finite-rate chemistry is the controlling process during the autoignition process for flame stabilization; at further downstream where the flame has established, the combustion progress is controlled by mixing, which is characteristic of nonpremixed flames. An examination of the particles with the largest sensitivities reveals the difference in the controlling mixtures for flame stabilization, namely, the stoichiometric mixtures are important for HM1, whereas, fuel-lean mixtures are controlling for HM3. The study demonstrates the potential of TPDF simulations with sensitivity analysis to investigate the effects of finite-rate chemistry on the flame characteristics and emissions, and reveal the controlling physio-chemical processes in MILD combustion.     

Combustion mechanism of ultralean rotating counterflow twin premixed flame

In our previous numerical studies [Nishioka Makihito, Zhenyu Shen, and Akane Uemichi. “Ultra-lean combustion through the backflow of burned gas in rotating counterflow twin premixed flames.” Combustion and Flame 158.11 (2011): 2188–2198. Uemichi Akane, and Makihito Nishioka. “Numerical study on ultra-lean rotating counterflow twin premixed flame of hydrogen–air.” Proceedings of the Combustion Institute 34.1 (2013): 1135–1142]. we found that methane– and hydrogen–air rotating counterflow twin flames (RCTF) can achieve ultralean combustion when backward flow of burned gas occurs due to the centrifugal force created by rotation. In this study, we investigated the mechanisms of ultralean combustion in these flames by the detailed numerical analyses of the convective and diffusive transport of the main species. We found that, under ultralean conditions, the diffusive transport of fuel exceeds its backward convective transport in the flame zone, which is located on the burned-gas side of the stagnation point. In contrast, the relative magnitudes of diffusive and convective transport for oxygen are reversed compared to those for the fuel. The resulting flows for fuel and oxygen lead to what we call a ‘net flux imbalance’. This net flux imbalance increases the flame temperature and concentrations of active radicals. For hydrogen–air RCTF, a very large diffusivity of hydrogen enhances the net flux imbalance, significantly increasing the flame temperature. This behaviour is intrinsic to a very lean premixed flame in which the reaction zone is located in the backflow of its own burned gas.     

Flame structure and burning velocity of flames propagating in binary iron aerosols

A numerical study was performed for binary dispersed iron aerosols in air using different particle sizes with constant average particle size. The effects of particle size and density of the two aerosols on flame structure and speed are systematically investigated. Varying the amount of small and big particles results in separated and overlapped flame fronts. For higher values of particle size ratio (ratio between the size of big and small particles) and density of small particles, flame fronts are observed to overlap. The flame speed of the binary mixture is compared with the mono-dispersed case and the difference is analyzed for different particle size ratios. The addition of a small fraction of small particles in the binary mixture is found to result in a substantial increase in the flame speed if the particle size ratio is large. Detailed analyses on the variation of the total amount of fuel shows the particle size ratio determines the equivalence ratio at which the maximum flame speed occurs. The maximum flame speed as a function of equivalence ratio was observed to move from the lean to the rich side for particle size ratio sufficiently large enough.