Annealing temperature influence on electrical properties of ion beam sputtered Bi2Te3 thin films

Ion beam sputtering process was used to deposit n-type fine-grained Bi₂Te₃ thin films on BK7 glass substrates at room temperature. In order to enhance the thermoelectric properties, thin films are annealed at the temperatures ranging from 100 to 400 °C. X-ray diffraction (XRD) shows that the films have preferred orientations in the c-axis direction. It is confirmed that grain growth and crystallization along the c-axis are enhanced as the annealing temperature increased. However, broad impurity peaks related to some oxygen traces increase when the annealing temperature reached 400 °C. Thermoelectric properties of Bi₂Te₃ thin films were investigated at room temperature. The Bi₂Te₃ thin films, including as-deposited, exhibit the Seebeck coefficients of −90 to −168 μV K⁻¹ and the electrical conductivities of 3.92×10²-7.20×10² S cm⁻¹ after annealing. The Bi₂Te₃ film with a maximum power factor of 1.10×10⁻³ Wm⁻¹ K⁻² is achieved when annealed at 300 °C. As a result, both structural and transport properties have been found to be strongly affected by annealing treatment. It was considered that the annealing conditions reduce the number of potential scattering sites at grain boundaries and defects, thus improving the thermoelectric properties.     

Effects of double filling of Pb and Ba on thermoelectric properties of PbxBayCo4Sb11.5Te0.5 compounds by HPHT

Skutterudite compounds Pb_xBa_yCo₄Sb_11.5Te_0.5 (x≤0.23,y≤0.27) with bcc crystal structure have been prepared by the high pressure and high temperature (HPHT) method. The study explored a chemical method for filling Pb and Ba atoms into the voids of CoSb₃ to optimize the thermoelectric figure of merit ZT in the system of Pb_yBa_xCo₄Sb_11.5Te_0.5. The structure of Pb_xBa_yCo₄Sb_11.5Te_0.5 skutterudites was evaluated by means of X-ray diffraction. The Seebeck coefficient, electrical resistivity and power factor were performed from room temperature to 710 K. Compared with Co₄Sb_11.5Te_0.5, the thermal conductivity of Pb and Ba double-filled samples was reduced evidently. Among all filled samples, Pb_0.03Ba_0.27Co₄Sb_11.5Te_0.5 showed the highest power factor of 31.64 μW cm⁻¹ K⁻² at 663 K. Pb_0.05Ba_0.25Co₄Sb_11.5Te_0.5 showed the lowest thermal conductivity of 2.73 W m⁻¹ K⁻¹ at 663 K, and its maximum ZT value reached 0.63 at 673 K.     

Electrical transport and high thermoelectric properties of PbTe doped with Bi2Te3 prepared by HPHT

In this paper, n-type lead telluride (PbTe) compounds doped with Bi₂Te₃ have been successfully prepared by high pressure and high temperature (HPHT) technique. The composition-dependent thermoelectric properties of PbTe doped with Bi₂Te₃ have been studied at room temperature. The figure-of-merit, Z, for PbTe is very sentivite to the dopants, which could be improved largely although the doped content of Bi₂Te₃ is very small (<0.08 mol%). In addition, the maximum value reaches to 9.3×10⁻⁴ K⁻¹, which is about 20% higher than that of PbTe alloyed with Bi₂Te₃ sintered at ambient pressure (7.6×10⁻⁴ K⁻¹) and several times higher than that of small grain size PbTe containing other dopants. The improved thermoelectric performance in this study may be due to the effect of high pressure and the low lattice thermal conductivity resulting from Bi₂Te₃ as source of dopants.     

Low-temperature thermoelectric properties of Bi85Sb15−xNbx alloys prepared by high-press sintering

The nanocrystalline materials with the general formula Bi₈₅Sb_15−xNb_x (x=0, 0.5, 1, 2, 3) were prepared by mechanical alloying and subsequent high-pressure sintering. Their transport properties involving electrical conductivity, Seebeck coefficient and thermal conductivity have been investigated in the temperature range of 80-300 K. The absolute value of Seebeck coefficient of Bi₈₅Sb₁₃Nb₂ reaches a maximum of 161 μV/K at 105 K, which is 69% larger than that of Bi₈₅Sb₁₅ at the same temperature. The power factor and figure-of-merit are 4.45×10⁻³ WK⁻²m⁻¹ at 220 K and 1.79×10⁻³ K⁻¹ at 196 K, respectively. These results suggest that thermoelectric properties of Bi₈₅Sb₁₅ based material can be improved by Nb doping.     

Electrochemical deposition of Bi2Te3-based thin films

The electrochemical reduction processes on stainless-steel substrates from an aqueous electrolyte composed of nitric acid, Bi³⁺, HTeO₂⁺, SbO⁺ and H₂SeO₃ systems were investigated using cyclic voltammetry. The thin films with a stoichiometry of Bi₂Te₃, Bi_0.5Sb_1.5Te₃ and Bi₂Te_2.7Se_0.3 have been prepared by electrochemical deposition at selected potentials. The structure, composition, and morphology of the films were studied by X-ray diffraction (XRD), environmental scanning electron microscopy (ESEM) and electron microprobe analysis (EMPA). The results showed that the films were single phase with the rhombohedral Bi₂Te₃ structure. The morphology and growth orientation of the films were dependent on the deposition potentials.     

Electrodeposition of n-type Bi2Te3−ySey thermoelectric thin films on stainless steel and gold substrates

Thermoelectric films of n-Bi₂Te_3−ySe_y were prepared by potentiostatic electrodeposition technique onto stainless steel and gold substrates at room temperature. These films were used for morphological, compositional and structural analysis by environment scanning electron microscope (ESEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The effect of different substrates on the structure and morphology of Bi₂Te_3−ySe_y films and relation between Se content in the electrodepositing solutions and in the films were also investigated. These studies revealed that Bi, Te and Se could be co-deposited to form Bi₂Te_3−ySe_y semiconductor compound in the solution containing Bi³⁺, HTeO₂⁺ and H₂SeO₃. The morphology and structure of the films are sensitive to the substrate material. The doped content of Se element in the Bi₂Te_3−ySe_y compound can be controlled by adjusting the Se⁴⁺ concentration in the electrodepositing solution. X-ray diffraction analysis indicates that the films prepared at −40 mV versus saturated calomel electrode (SCE) exhibit strong (1 1 0) orientation with rhombohedral structure.     

Preferential growth of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> films with a nanolayer structure: enhancement of thermoelectric properties induced by nanocrystal boundaries

Preferential growth of different crystal planes in layered Bi₂Te₃ thin films with each layer <40 nm has been achieved by a simple magnetron co-sputtering method. The preferential growth of (015) plane or (001) was achieved at special depositing conditions due to the more sufficient growth along the in-plane direction induced by the enhanced diffusion of atoms and lower deposition rate. The Bi₂Te₃ film with preferential growth of (001) plane possesses about two times higher electrical conductivity and Seebeck coefficient as compared to the film with preferential growth of (015) plane, due to the greatly enhanced carrier mobility. Furthermore, the thermal conductivity has been suppressed due to more phonon scattering at grain boundaries, compared with ordinary Bi₂Te₃ alloys and films.     

Thermoelectric properties of the Bi2−xYxRu2O7 (x=0-2) pyrochlores

Electrical conductivity and Seebeck coefficient for the Bi_2−xY_xRu₂O₇ pyrochlores with x=0.0,0.5,1.0,1.5,2.0 were measured in the temperature range of 473-1073 K in air. With increasing Bi content, the temperature dependence of the electrical conductivity changed from semiconducting to metallic. The signs of the Seebeck coefficient were positive in the measured temperature range for all the samples, indicating that the major carriers were holes. The temperature dependence of the Seebeck coefficient for the Y₂Ru₂O₇ indicated the thermal activation-type behavior of the holes, while that for the Bi_2−xY_xRu₂O₇ with x=0.0-1.5 indicated the itinerant behavior of the holes. The change in the conduction behavior from semiconductor to metal with increasing Bi content is consistent with the increase in the overlap between the Ru4d t_2g and O2p orbitals, but the mixing of Bi6s, 6p states at E_F may not be ruled out. The thermoelectric power factors for the Bi_2−xY_xRu₂O₇ with x=1.5 and 2.0 were lower than 10⁻⁵ W m⁻¹ K⁻² and those with x=0.0,0.5,1.0 were around 1-3×10⁻⁵ W m⁻¹ K⁻².     

Optical and thermoelectric characterizations of electroplated n-Bi2(Te0.9Se0.1)3

Bismuth selenotelluride (Bi₂(Te_0.9Se_0.1)₃) films were electrodeposited at constant current density from acidic aqueous solutions with Arabic gum in order to produce thin films for miniaturized thermoelectric devices. X-ray fluorescence spectroscopy determined film compositions. X-ray diffraction pattern shows that the films as deposited are polycrystalline, isostructural to Bi₂Te₃ and covered by crystallites. Mueller-matrix analysis reveals that the electroplated layers are optically like an isotropic medium. Their pseudo-dielectric functions were determined using mid-infrared spectroscopic ellipsometry. Tauc-Lorentz combined with Drude dispersion relations were successfully used. The energy band gap E_g was found to be about 0.15 eV. Moreover, the fundamental absorption edge was described by an indirect optical band-to-band transition. From Seebeck coefficient measurement, films exhibit n-type charge carrier and the value of thermoelectric power is about −40 μV/K.     

Thermoelectric properties of Bi0.9Sb0.1 prepared by high pressure

The Bi_0.9Sb_0.1 powders were prepared by mechanical alloying and then pressed under 6 GPa at different pressing temperatures. X-ray diffraction spectra showed that the single phase was formed. The nanostructure of grain was observed by bright-field imaging. Electrical conductivity, Seebeck coefficient, and thermal conductivity had been investigated in the temperature range of 80-300 K. The absolute Seebeck coefficient value of 120.3 μV/K was measured at 130 K. The figure-of-merit reached a maximum value of 0.90×10⁻³ K⁻¹ at 140 K.     

Improved thermoelectric performance of n-type Mg3Sb2–Mg3Bi2 alloy with Co element doping

n-type Mg₃Sb₂–Mg₃Bi₂ alloy shows as a potential new thermoelectric material (TE) and has been widely researched recently. The pure phase n-type Mg_3·20(Sb_0·3Bi_0.7)_1.99Te_0.01 were prepared by adjusting Mg content with the Bi impurity phase being effectively suppressed. Then, Co element was doped into the pure phase and the electrical conductivity of samples were improved. With a high power factor of 20.3 μW cm⁻¹K⁻² for Mg_3·185Co_0·015(Sb_0·3Bi_0.7)_1.99Te_0.01 at 525 K. Additionally, it was found that the phonon scattering is enhanced due to the larger atomic mass of Co comparing to Mg and the lattice thermal conductivity is reduced. As a result, a high ZT value of ~ 1.03 at 525 K is achieved for the Mg_3·185Co_0·015(Sb_0·3Bi_0.7)_1.99Te_0.01.     

Thermoelectric properties of sol-gel derived cobaltite Bi2Ca2.4Co2Oy

Layered misfit cobaltite Bi₂Ca_2.4Co₂O_y has been synthesized by a sol-gel method. This compound exhibits large thermoelectric (TE) power (S_300 K∼170 μV K⁻¹), low resistivity (ρ_300 K∼42 mΩ cm) and relatively small thermal conductivity (κ_300 K∼2.8 W K⁻¹ m⁻¹) at room temperature. Furthermore, the resistivity of this compound displays a metallic behavior above T^?∼150 K with a semiconducting behavior below this temperature. This abnormal behavior in resistivity is analogous to those observed in Sr and Ba based misfit cobaltites. The observed features of the TE have been discussed based on the narrow band model.     

Hyperfine characterization of Bi1.9Te0.1SrNb1.9Hf0.1O9

The Aurivillius type oxide Bi_1.9Te_0.1SrNb_1.9Hf_0.1O₉ has been studied by Perturbed Angular Correlations spectroscopy using ¹⁸¹Ta probes. The spin precession curves were measured from room temperature up to 873 K. Two sites are occupied by probes and the temperature dependence of both indicates a continuous phase transition at about 625 K. One site is ordered while the other is disordered. This situation is analyzed in terms of simple models already applied to perovskites. The transition temperature of the solid solution Bi_2−xTe_xSrNb_2−xHf_xO₉ (with 0≤x≤0.5) shows a strong dependence on composition.     

Effect of Bi2O3 on EPR, optical transmission and DC conductivity of vanadyl doped alkali bismuth borate glasses

Glasses with composition xBi₂O₃·(30−x)M₂O·70B₂O₃ (M=Li, Na) containing 2 mol% V₂O₅ have been prepared over the range 0≤x≤15 (x is in mol%). The electron paramagnetic resonance spectra of VO²⁺ of these glasses have been recorded in the X-band (≈9.3 GHz) at room temperature (RT≈300 K). Spin Hamiltonian parameters, g_∥, g_⊥, A_∥, A_⊥, dipolar hyperfine coupling parameter, P, and Fermi contact interaction parameter, K, have been calculated. The molecular orbital coefficients, α² and γ², have been calculated by recording the optical transmission spectra. In xBi₂O₃·(30−x)Li₂O·70B₂O₃ glasses there is decrease in the tetragonality of the V⁴⁺O₆ complex for x up to 6 mol% whereas for x≥6 mol%, tetragonality increases. In xBi₂O₃·(30−x)Na₂O·70B₂O₃ glasses there is increase in the tetragonality of the V⁴⁺O₆ complex with increasing x. The 3d_xy orbit expands with increase in Bi₂O₃:M₂O ratio. Values of the theoretical optical basicity, Λ_th, have also been reported. The DC conductivity increases with increase in temperature. The order of conductivity is 10⁻⁵ ohm⁻¹ m⁻¹ at low temperature and 10⁻³ ohm⁻¹ m⁻¹ at high temperature. The DC conductivity decreases and the activation energy increases with increase in Bi₂O₃:M₂O ratio.     

Superconductivity and non-metallicity induced by doping the topological insulators Bi2Se3 and Bi2Te3

We show that by Ca doping the Bi₂Se₃ topological insulator, the Fermi level can be fine tuned to fall inside the band gap and therefore suppresses the bulk conductivity. Non-metallic Bi₂Se₃ crystals are obtained. On the other hand, the Bi₂Se₃ topological insulator can also be induced to become a bulk superconductor, with T_c∼3.8 K, by copper intercalation in the van der Waals gaps between the Bi₂Se₃ layers. Likewise, an as-grown crystal of metallic Bi₂Te₃ can be turned into a non-metallic crystal by slight variation in the Te content. The Bi₂Te₃ topological insulator shows small amounts of superconductivity with T_c∼5.5 K when reacted with Pd to form materials of the type Pd_zBi₂Te₃.     

Temperature dependence of the Raman spectra of Bi2Te3 and Bi0.5Sb1.5Te3 thermoelectric films

The temperature dependence of the Raman spectra of Bi₂Te₃ and Bi_0.5Sb_1.5Te₃ thermoelectric films was investigated. The temperature coefficients of the E_g(2) peak positions were determined as –0.0137 cm^–1/°C and –0.0156 cm^–1/°C, respectively. The thermal expansion of the crystal caused a linear shift of the Raman peak induced by the temperature change. Based on the linear relation, a reliable and noninvasive micro‐Raman scattering method was shown to measure the thermal conductivity of the thermoelectric films. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Hall mobility of amorphous Ge2Sb2Te5

The electrical conductivity, Seebeck coefficient, and Hall coefficient of three-micron-thick films of amorphous Ge₂Sb₂Te₅ have been measured as functions of temperature from room temperature down to as low as 200 K. The electrical conductivity manifests an Arrhenius behavior. The Seebeck coefficient is p-type with behavior indicative of multi-band transport. The Hall mobility is n-type and low (near 0.07 cm²/V s at room temperature).     

Transport coefficients and defect structure of Sb2−xAgxTe3 single crystals

Incorporation of Ag in the crystal lattice of Sb₂Te₃ creates structural defects that have a strong influence on the transport properties. Single crystals of Sb_2−xAg_xTe₃ (x=0.0; 0.014; 0.018 and 0.022) were characterized by measurements of the temperature dependence of the electrical resistivity, Hall coefficient, Seebeck coefficient and thermal conductivity in the temperature range of 5-300 K. With an increasing content of Ag the electrical resistance, the Hall coefficient and the Seebeck coefficient all decrease. This implies that the incorporation of Ag atoms in the Sb₂Te₃ crystal structure results in an increasing concentration of holes. However, the doping efficiency of Ag appears to be only about 50% of the expected value. We explain this discrepancy by a model based on the interaction of Ag impurity with the native defects in the Sb_2−xAg_xTe₃ crystal lattice. Defects have a particularly strong influence on the thermal conductivity. We analyze the temperature dependence of the lattice thermal conductivity in the context of the Debye model. Of the various phonon scattering contributions, the dominant influence of Ag incorporation in the crystal lattice of Sb₂Te₃ is revealed to be point-defect scattering where both the mass defect and elastic strain play a pivotal role.     

Power factor enhancement in Pr-substituted alloys prepared by high-pressure sintering

Bi₈₅Sb_15−xPr_x (x=0,1,2,3) alloys with partial substitution of Pr for Sb were synthesized by mechanical alloying followed by high-pressure sintering. The crystal structure was characterized by X-ray diffraction. The electrical conductivity and Seebeck coefficient were measured in the temperature range of 80–300 K. The results show that the electrical conductivity and Seebeck coefficient of Pr-substituted samples are both larger than those of the reference sample, Bi₈₅Sb₁₅, in the whole measurement temperature range. The power factor of Bi₈₅Sb₁₃Pr₂ reaches a maximum value of 3.83×10⁻³ W K⁻² m⁻¹ at 235 K, which is about four times larger than that of the reference sample, Bi₈₅Sb₁₅, at the same temperature.     

Enhanced power factor of Ag0.208Sb0.275Te0.517 prepared by HPHT

In this Letter, p-type thermoelectric materials Ag_0.208Sb_0.275Te_0.517 with enhanced power factor were prepared by high pressure and high temperature (HPHT) method. The samples are near single phase AgSbTe₂ with a very small quantity of impurities including Ag₂Te and Te. The concentration of impurities decreases with an increase of synthetic pressure. The synthetic pressure-dependent transport properties including electrical resistivity, Seebeck coefficient and power factor were studied at room temperature. We find the power factor of the sample prepared at the synthetic pressure of 2.1 GPa reaches a maximum value of 14.6 μW cm⁻¹ K⁻², which is about two times higher than that of the same sample prepared at normal pressure (6.9 μW cm⁻¹ K⁻²).