Titrimetric analysis of total mercury ions including mercury(I) ions

A systematic analytical method is proposed and applied to directly determine the total concentration of Hg(II) and Hg(I) ions in water. Experimental results demonstrate that this method provides a low detection limit of 0.05 mM and small relative error within 1.5% in an ion concentration range of 0.2–50 mM. The technique is especially applicable for sample solutions that the traditional titration method like Volhard and EDTA complexation titrimetry could not analyze directly. This method could be employed to analyze solutions in any ratio of Hg(II) and Hg(I) ions including pure Hg(II) or pure Hg(I) ions, exhibiting several advantages, such as simple operation, good reproducibility, and low cost. Correspondence: Xin-Gui Li, Key Laboratory of Advanced Civil Engineering Materials, Institute of Materials Chemistry, College of Materials Science and Engineering, Tongji University, 1239 Siping Road, Shanghai 200092, China.     

Isotopic fractionation of mercury induced by reduction and ethylation

Isotope ratio measurements characterizing ²⁰²Hg/²⁰⁰Hg in NIST SRM 3133 Mercury Standard Solution were undertaken by multicollector inductively coupled plasma mass spectrometry employing NIST SRM 997 Tl for mass bias correction by use of the slope and the intercept obtained from a natural logarithmic plot of each session of measurements of ²⁰²Hg/²⁰⁰Hg against ²⁰⁵Tl/²⁰³Tl. The calculated value of 1.285333 ± 0.000192 (mean and one standard deviation, n = 40) for the mass bias corrected ²⁰²Hg/²⁰⁰Hg was then used for mass bias correction of other Hg isotope pairs. Ratios of 0.015337 ± 0.000011, 1.68770 ± 0.00054, 2.3056 ± 0.0015, 1.3129 ± 0.0013, 2.9634 ± 0.0038, and 0.67937 ± 0.0013 (expanded uncertainty, k = 2) were obtained for ¹⁹⁶Hg/¹⁹⁸Hg, ¹⁹⁹Hg/¹⁹⁸Hg, ²⁰⁰Hg/¹⁹⁸Hg, ²⁰¹Hg/¹⁹⁸Hg, ²⁰²Hg/¹⁹⁸Hg, and ²⁰⁴Hg/¹⁹⁸Hg, respectively. Reduction of Hg(II) to Hg⁰ in solutions of SRM 3133 was then undertaken using SnCl₂, NaBH₄, UV photolysis in the presence of formic acid, and ethylation of Hg(II) using NaBEt_4. These reactions induced significant isotope fractionation with maximum values of 1.17 ± 0.07, 1.08 ± 0.09, 1.34 ± 0.07, and 3.59 ± 0.09‰ (one standard deviation, 1SD, n = 5) for δ ^202/198Hg relative to the initial isotopic composition in the solution following 85–90% reduction of the Hg by SnCl₂, NaBH₄, UV photolysis, and ethylation with NaBEt₄, respectively. Mass-dependent fractionation was found to be dominant for all reduction processes. Figure Mass dependence of fractionation for all samples from Hg fractionation experiments using NaBEt₄. Solid lines are the theoretically predicted MDF based on δ′ ^202/198 Hg using equation 7. Error bars displayed are one standard deviation of the mean of 5 measurements of each sample     

Determination of mercury(II) traces in drinking water by inhibition of an urease reactor in a flow injection analysis (FIA) system

 The integration of an urease reactor into a gas diffusion flow injection system was investigated for the determination of urease inhibitors. The enzyme was immobilized by entrapping in polyacrylamide gel. Besides copper and silver ions mercury ions inhibit the conversion of urea to carbon dioxide and ammonia catalysed by urease. The pH change of the carrier solution caused by the ammonia released was measured potentiometrically with a pH electrode. The inhibition behaviour of Hg(II) ions was investigated. A linear range from 2 to 20 μg L^-1 Hg(II) was obtained after a 90 s inhibition, with a correlation coefficient of r=0.9997. The relative standard deviation was 1.4% for five measurements of 2 μg L^-1Hg(II). A sample frequency of 7 h^-1 was achieved. The inhibited enzyme can be reactivated. The method was applied to the determination of Hg(II) in two drinking water samples. Received: 16 April 1996/Revised: 3 June 1996/Accepted: 11 June 1996     

Electrochemical kinetic study about cobalt electrodeposition onto GCE and HOPG substrates from sulfate sodium solutions

In the present work, we analyze the electrodeposition of cobalt by electrochemical techniques onto GCE (system I) and HOPG (system II) electrodes from sulfate solutions. Cyclic voltammetry and current transient measurements were used to obtain the nucleation and growth mechanism. The results clearly showed that electrodeposition of cobalt is a diffusion-controlled process with a typical 3D nucleation mechanism in both substrates. The average ΔG calculated for the stable nucleus formation was 1.97 × 10⁻²⁰ J nuclei⁻¹ and 3.58 × 10⁻²⁰ J nuclei⁻¹ for system I and system II, respectively. The scanning electron microscope (SEM) images indicated similar nucleation and growth processes on GCE and HOPG substrates at same overpotential with a homogeneous disperse cobalt clusters. X-ray energy-dispersive spectroscopy (EDS) was performed in order to ensure that the clusters formed are cobalt. The nuclei’s size obtained was dependent of the overpotential applied; at lower overpotentials, the growth rate of the cobalt clusters diminishes when their number increases due to the strongly reduced concentration of cobalt ions because of their consumption by a larger number of growing particles. A theoretical quantum study employing PM6 method suggests that Na⁺ adsorbed deactivate the local surface occasionating the formation of disperse cobalt clusters on carbon electrodes.     

Spectrophotometric titration of mercury(II) with ethylenedithiodiacetic acid

Summary Mercuric ions may be determined by titration with ethylenedithiodiacetic acid at a wavelength of 260 nm at any pH less than 1. The method is simple, rapid, and selective, and is applicable in solutions of high electrolyte concentration. Mercury(II) can be determined down to 1.5×10^–5 M with a relative standard deviation less than 2%.

---

Zusammenfassung Quecksilber (II) läßt sich mit Äthylendithiodiessigsäure bei 260 nm und pH1 titrieren. Das Verfahren ist einfach, rasch und selektiv. Es läßt sich auch für Lösungen mit hoher Elektrolytkonzentration anwenden. Hg(II)-Konzentrationen über 1,5×10^–5 M sind mit einer relativen Standardabweichung unter 2% bestimmbar.

     

Biosorption of mercury by carboxymethylcellulose and immobilized Phanerochaete chrysosporium

Phanerochaete chrysosporium basidiospores immobilized onto carboxymethylcellulose were used for the removal of mercury ions from aqueous solutions. The biosorption of Hg(II) ions onto carboxymethylcellulose and both immobilized live and heat-inactivated fungal mycelia of Phanerochaete chrysosporium was studied using aqueous solutions in the concentration range 30-700 mg l⁻¹. The biosorption of Hg(II) ions by the carboxymethylcellulose and both live and heat-inactivated immobilized preparations increased as the initial concentration of mercury ions increased in the medium. Maximum biosorption capacity for immobilized live and heat-inactivated fungal mycelia of Phanerochaete chrysosporium was found to be 83.10 and 102.15 mg Hg(II) g⁻¹, respectively, whereas the amount of Hg(II) ions adsorbed onto the plain carboxymethylcellulose beads was 39.42 mg g⁻¹. Biosorption equilibria were established in approximately 1 h and the correlation regression coefficients show that the adsorption process can be well defined by a Langmuir equation. Temperature changes between 15 and 45 °C did not affect the biosorption capacity. The effect of pH was also investigated and the maximum adsorption of Hg(II) ions onto the carboxymethylcellulose and both live and heat-inactivated immobilized fungal mycelia was observed at pH 6.0. The carboxymethylcellulose-fungus beads could be regenerated using 10 mM HCl, with up to 95% recovery. The biosorbents were used in three biosorption-desorption cycles and no significant loss in the biosorption capacity was observed.     

Copper(II) ion-selective microelectrochemical transistor

A device has been developed for the measurement of copper(II) ions (Cu²⁺) in aqueous medium. The device reported here is an electrochemical transistor which consists of two platinum electrodes separated by 100 μm spacing and bridged with an anodically grown film of polycarbazole. Polycarbazole film (undoped form) is observed to be highly selective for the Cu(II) ions. In a completed device, the conductivity of the polycarbazole film changes on addition of Cu(II) ions. The change in conductivity is attributed to the conformational changes in the polymer phase on occupation of the Cu(II) ions, without affecting electron/proton transfer. The device turns on by adding 2.5 × 10⁻⁶ M Cu(II) ions and reaches a saturation region beyond 10⁻⁴ M Cu(II) ion concentrations. In the above concentration range, the device response [I _D vs. log Cu(II) ion concentration] is linear. The selectivity of the device for other metal ions such as Cu(I), Ni(II), Co(II), Fe(II), Fe(III), Zn(II) and Pb(II) is also studied. Received: 6 April 1999 / Accepted: 20 August 1999     

Perchlorate selective membrane electrodes based on a platinum complex

Three platinum(II) complexes were synthesized and studied to characterize their ability as an anion carrier in a PVC membrane electrode. The polymeric membrane electrodes (PME) and also coated glassy carbon electrodes (CGCE) prepared with one of these complexes showed excellent response characteristics to perchlorate ions. The electrodes exhibited Nernstian responses to ClO₄ ⁻ ions over a wide concentration range from 1.5 × 10⁻⁶ to 2.7 × 10⁻¹ M for PME and 5.0 × 10⁻⁷ to 1.9 × 10⁻¹ M for CGCE with low detection limits (9.0 × 10⁻⁷ M for PME and 4.0 × 10⁻⁷ M for CGCE). The electrodes possess fast response time, satisfactory reproducibility, appropriate lifetime and, most importantly, good selectivity toward ClO₄ ⁻ relative to a variety of other common anions. The potentiometric response of the electrodes is independent of the pH of the test solution in the pH range 2.0–9.0. The proposed sensors were used in potentiometric determination of perchlorate ions in mineral water and urine samples. Correspondence: Ahmad Soleymanpour, Department of Chemistry, Damghan Basic Science University, Damghan, Iran.     

Nanosized centers for mercury(II) ions adsorption on a surface of modified silica

The present work investigates the adsorptive interactions of Hg(II) ions in aqueous medium with hydroxylated silica, aminopropylsilica and silica chemically modified by β-cyclodextrin. Batch adsorption studies were carried out with various agitation times and mercury(II) concentrations. The maximum adsorption was observed within 15–30 min of agitation. The kinetics of the interactions, tested with the model of Lagergren for pseudo-first and pseudo-second order equations, showed better agreement with first order kinetics (k₁ = 3.4 ± 0.2 to 5.9 ± 0.3 min⁻¹). The adsorption data gave good fits with Langmuir isotherms. The results have shown that β-cyclodextrin-containing adsorbent has the largest adsorption specificity to Hg(II): K _L = 4125 ± 205 mmol⁻¹. “β-cyclodextrin-NO3-” inclusion complexes with ratio 1: 1 and super molecules with composition C₄₂H₇₀O₃₅ ⊎ 3 Hg(NO₃)₂ are formed on the surface of β-cyclodextrin-containing silica.      

Rapid and sensitive spectrofluorimetric determination of trace amounts of Hg(II) with o-vanillin-8-aminoquinoline

The fluorimetric determination of mercury ions with o-vanillin-8-aminoquinoline (OVAQ) in aqueous solutions was investigated. Hg(II) could react with the fluorescent reagent OVAQ (λ_ex/em = 278/314 nm) to form a nonfluorescent complex in an ethanol-water medium of pH 6.00. The linear range of the proposed method was from 2.5 to 80 μg/L, and the detection limit was 0.80 μg/L. The interferences of 24 foreign ions were also studied. The method was successfully applied to the determination of Hg(II) in sludge. The text was submitted by the authors in English.     

Potentiometric Determination of Menadione (Vitamin K3)

 The construction and electrochemical response characteristics of poly(vinyl) chloride matrix membrane sensors for menadione (vitamin K₃) are described. Membranes incorporating the ion association complexes of menadione anion with bathophenanthroline nickel(II) and iron(II) as electroactive materials show linear response for menadione over the range 10⁻¹–10⁻⁵ M with anionic slopes of 58.2–51.4 mV per concentration decade. Both sensors exhibit fast response time (20–30 s), low detection limit (2 × 10⁻⁵ M), good stability (4–6 weeks) and selectivity coefficient (10⁻¹–10⁻³). Direct potentiometric determination of menadione under static and hydrodynamic mode of operations shows average accuracies of 98.8 and 98.5% with relative standard deviations of 0.6% and 1.3%, respectively. Application of the method for the determination of menadione in human plasma gives favourable results compared with those obtained by the standard spectrophotometric method. Received February 26, 2001. Revision October 1, 2001.     

Evaluation and application of argon and helium microstrip plasma for the determination of mercury by the cold vapor technique and optical emission spectrometry

The suitability of a 2.45-GHz atmospheric pressure, low-power microwave microstrip plasma (MSP) operated with Ar and He for the determination of Hg by continuous-flow cold vapor (CV) generation, using SnCl₂/HCl as the reducing agent, and optical emission spectrometry (OES) using a small CCD spectrometer was studied. The areas of stability for a discharge in the Ar and in the He MSP enclosed in a cylindrical channel in a quartz wafer were investigated. The excitation temperatures as measured for discharge gas atoms (Ar I, He I), and the electron number densities at 35–40 W and 15–400 mL min⁻¹ were found to be at the order of 3,200–5,500 K and 0.8 × 10¹⁴–1.6 × 10¹⁴ cm⁻³, respectively. The relative intensity of the Hg I 253.6-nm line and the signal-to-background ratio as a function of the forward power (35–40 W) as well as of the flow rate of the working gas (15–400 mL min⁻¹) were evaluated and discussed. For the selected measurement conditions, the Ar MSP was established to have the lower detection limit for Hg (0.6 ng mL⁻¹) compared with the He MSP. The linearity range is up to 300 ng mL⁻¹ and the precision is on the order of 1–3%. With the optimized CV Ar MSP-OES method a determination of Hg in spiked domestic and natural waters at concentration levels of 20–100 μg L⁻¹ and an accuracy of 1–4% could be performed. In an NIST domestic sludge standard reference material, Hg (3.64 μg g⁻¹) could be determined with a relative standard deviation of 4% and an agreement better than 4%.     

An infrared spectroscopic based method for mercury(II) detection in aqueous solutions

A new method that uses solid phase extraction (SPE) coupled with FTIR spectroscopy to detect Hg(II) in aqueous samples is described. The technique is envisioned for on-site, field evaluation rather than lab-based techniques. This paper presents the “proof of principle” of this new approach toward measurements of Hg(II) in water and identifies mass transport issues that would need to be overcome in order to migrate from a lab based method to field operation. The SPE material supported on a Si wafer is derivatized with an acylthiosemicarbazide, which undergoes a reaction in the presence of aqueous Hg(II) to form an oxadiazole ring. The progress of the reaction is monitored by IR spectroscopy. Following EPA guidelines, the method of detection limit (MDL) for the SPE/IR was 5 μg of Hg(II) cm⁻². In a 1 L sample and a 1 cm² Si wafer, this translates to a detection limit of 5 ppb. This system shows a high selectivity toward aqueous Hg(II) over other thiophilic heavy metal ions such as Pb(II), Cd(II), Fe(III), and Zn(II) and other metal ions such as Ni(II), Mn(II), Co(II), Cu(II), In(III), Ru(III), Na(I), and Ag(I) in aqueous solutions.     

Vermiculite clay mineral as an effective carbon paste electrode modifier for the preconcentration and voltammetric determination of Hg(II) and Ag(I) ions

A vermiculite modified carbon paste electrode (VMCPE) was employed for the in situ preconcentration of traces of Hg(II) and Ag(I) via an ion-exchange route. Heavy metal ions were accumulated in Britton-Robinson (BR) buffer pH 7 for Hg(II) and pH 6 for Ag(I), and afterwards reduced at –0.7 V vs. Ag/AgCl in the separate measurement solution (BR buffer pH 5 + 0.05 mol/L NaNO₃) prior to the anodic stripping square-wave voltammetric (ASSWV) detection. For Hg(II) ions, at 15 min accumulation, a linear range from 1.0 × 10^–7 to 8.0 × 10^–6 mol/L was obtained, with a 5.7 × 10^–8 mol/L limit of detection. The VMCPE response was linear for Ag(I) ions in the concentration range from 2.0 × 10^–7 to 8.0 × 10^–6 mol/L, at 10 min accumulation with a corresponding limit of detection of 6.3 × 10^–8 mol/L. The relative standard deviation of the analytical procedure including accumulation from a 5 × 10^–7 mol/L solution of Hg (15 min) or Ag(I) (10 min), electrolysis, ASSWV detection, regeneration and activation of the VMCPE, was 4% (n = 6). The optimisation of the parameters for the application of the VMCPE in combination with ASSWV detection is presented and discussed. Received: 10 July 1997 / Revised: 31 October 1997 / Accepted: 3 November 1997     

Natural pyrite as an electrochemical sensor for potentiometric titrations with EDTA, mercury(II) and silver(I)

The results obtained in potentiometric titrations of copper(II), mercury(II) and iron(III) with standard EDTA solutions are presented. The titration of copper(II) at pH values in the range from 8.11 to 10.99 (ammonia buffer) and the titration of mercury(II) and iron(III) at pH values from 3.59 to 5.65 (acetate buffer) were performed. The titration end-point (TEP) was detected with an indicator electrode made from natural crystalline pyrite as an electrochemical sensor. The results obtained in potentiometric titration with the pyrite electrode were compared with those obtained using a platinum electrode (Fe³⁺), a Cu ion selective electrode (Cu²⁺) and a Hg electrode (Hg²⁺). Accurate and reproducible results with good agreement were obtained, but higher potential changes at the TEP were obtained using the pyrite electrode. In the course of the titration the potential was established within less than 1 min, whereas at the TEP it was within about 2–3 min. The potential changes at the TEP were in the range from 60 to 200 mV per 0.1 ml EDTA, according to the stability constant of the complex formed. The highest potential changes, ranging from 160 to 200 mV, were obtained in the titration of iron(III) at pH 3.59. Reverse titration was also performed and accurate and reproducible results were obtained. Moreover, titration of halogenide and thiocyanate with standard mercury(II) solutions, as well as cyanide with silver(I) solution, were performed and accurate and reproducible results were again obtained. Received: 20 February 1998 / Accepted: 19 November 1999     

Determination of trace amounts of mercury(II) in water samples using a novel kinetic catalytic ligand substitution reaction of hexacyanoruthenate(II)

A simple, sensitive, selective and rapid kinetic catalytic method has been developed for the determination of Hg(II) ions at micro-level. This method is based on the catalytic effect of Hg(II) ion on the rate of substitution of cyanide in hexacyanoruthenate(II) with nitroso-R-salt (NRS) in aqueous medium and provides good accuracy and precision. The concentration of Hg(II) catalyst varied from 4.0 to 10.0 × 10⁻⁶ M and the progress of reaction was followed spectrophotometrically at 525 nm (λ_max of purple-red complex [Ru(CN)₅NRS]³⁻,  = 3.1 × 10³ M⁻¹ s⁻¹) under the optimized reaction conditions; 8.75 × 10⁻⁵ M [Ru(CN)₆⁴⁻], 3.50 × 10⁻⁴ M [nitroso-R-salt], pH 7.00 ± 0.02, ionic strength, I = 0.1 M (KCl), temp 45.0 ± 0.1 °C. The linear calibration curves, i.e. calibration equations between the absorbance at fixed times (t = 15, 20 and 25 min) versus concentration of Hg(II) ions were established under the optimized experimental conditions. The detection limit was found to be 1.0 × 10⁻⁷ M of Hg(II). The effect of various foreign ions on the proposed method has also been studied and discussed. The method has been applied to the determination of mercury(II) in aqueous solutions.     

A PVC plasticized membrane sensor for nickel ions

A new PVC membrane sensor, which is highly selective towards Ni (II) ions, has been developed using a thiophene-derivative Schiff base as the ionophore. The best performance was exhibited by the membrane having the composition percentage ratio of 5:3:61:31 (ionophore:NaTPB:DBP:PVC) (w/w), where NaTPB is the anion excluder, sodium tetraphenylborate and DBP is the plasticizing agent (dibutyl phthalate). The membrane exhibited a good Nernstian response for nickel ions over the concentration range of 1.0 × 10⁻¹–5.0 × 10⁻⁶ M (limit of detection is 1.8 × 10⁻⁶ M) with a slope of 29.5 ± 1.0 mV per decade of activity. It has a fast response time of <20 s and can be used for a period of 4 months with good reproducibility. The sensor is suitable for use in aqueous solutions of a wide pH range of 3.2–7.9. The sensor shows high selectivity to nickel ions over a large number of mono-, bi- and trivalent cations. It has been successfully used as an indicator electrode in the potentiometric titration of nickel ions against EDTA and also for direct determination of nickel content in real samples – wastewater samples from electroplating industries and Indian chocolates.     

Media Influence on the Enhancement of the Fluorescence of Berberine Hydrochloride

 Berberine hydrochloride is an alkaloid with little or no fluorescence in water. In sodium dodecylsulfate solutions, the fluorescence intensity of this compound is enhanced several folds by ion-pairing with the anion of the surfactant. The enhanced fluorescence intensity reaches a maximum at a surfactant concentration of 4·10⁻³ M and then decreases to a constant value at the critical micelle concentration and beyond. At concentrations near the maximum, a calibration sensitivity of 3.23·10⁶/M was obtained. In addition, a good linear dynamic range and a low limit of detection (4·10⁻⁵ and 1.5·10⁻⁷ M, respectively) were determined. This observation indicates that this surfactant medium could be effectively used in fluorometric trace analysis of berberine hydrochloride. It was also observed in this work that solvents of low dielectric constant tend to stabilize this compound and thereby enhance its fluorescence.     

Synthesis and characterization of silica gel microspheres encapsulated by salicyclic acid functionalized polystyrene and its adsorption of transition metal ions from aqueous solutions

The present study was undertaken to develop a novel adsorbent for heavy metal ions, and this paper presents the synthesis and characterization of a composite material-silica gel microspheres encapsulated by salicyclic acid functionalized polystyrene (SG-PS-azo-SA) with a core-shell structure. SG-PS-azo-SA was used to investigate the adsorption of Mn(II), Co(II), Ni(II), Fe(III), Hg(II), Zn(II), Cd(II), Cr(VI), Pd(II), Cu(II), Ag(I), and Au(III) from aqueous solutions. The results revealed that SG-PS-azo-SA has better adsorption capacity for Cu(II), Ag(I) and Au(III). Langmuir and Freundlich isotherm models were applied to analyze the experimental data, the best interpretation for the experimental data was given by the Langmuir isotherm equation with the maximum adsorption capacity for Cu(II), Ag(I), and Au(III) at 1.288 mmol g⁻¹, 1.850 mmol g⁻¹ and 1.613 mmol g^t-1, respectively. Thus, silica gel encapsulated by salicyclic acid functionalized polystyrene (SG-PS-azo-SA) is favorable and useful for the removal of Cu(II), Ag(I) and Au(III) metal ions.     

Media Influence on the Enhancement of the Fluorescence of Berberine Hydrochloride

Summary.  Berberine hydrochloride is an alkaloid with little or no fluorescence in water. In sodium dodecylsulfate solutions, the fluorescence intensity of this compound is enhanced several folds by ion-pairing with the anion of the surfactant. The enhanced fluorescence intensity reaches a maximum at a surfactant concentration of 4·10⁻³ M and then decreases to a constant value at the critical micelle concentration and beyond. At concentrations near the maximum, a calibration sensitivity of 3.23·10⁶/M was obtained. In addition, a good linear dynamic range and a low limit of detection (4·10⁻⁵ and 1.5·10⁻⁷ M, respectively) were determined. This observation indicates that this surfactant medium could be effectively used in fluorometric trace analysis of berberine hydrochloride. It was also observed in this work that solvents of low dielectric constant tend to stabilize this compound and thereby enhance its fluorescence. Received November 26, 1999. Accepted (revised) January 13, 2000