The properties of nickel aluminate nanoparticles prepared by sol–gel and impregnation methods

Nickel aluminates were prepared by sol–gel and impregnation methods and calcined at 1100 °C. The sol–gel made samples were prepared with different amounts of nickel (Ni/Al molar ratio equal to 0, 0.25, 0.5, and 0.75) and aging times (24 and 48 h). The samples were characterized by X-ray diffraction, induced couple plasma, nitrogen physisorption, transmission and scanning electron microscopy, and ammonia temperature programmed desorption (NH₃-TPD). In the sol–gel made samples, only the NiAl₂O₄ structure of nickel aluminate was defined, while for impregnation, NiAl₁₀O₁₆ was formed as well. The sol–gel made samples had low specific surface areas (7.7–12.4 m²/g), but a sample prepared by impregnation method had higher specific surface area (67.2 m²/g). The surface acidity density decreased by increasing the amount of nickel and was the lowest for impregnation method.     

The morphologies and optoelectronic properties of delafossite CuFeO2 thin films prepared by PEG assisted sol–gel method

Single phase delafossite CuFeO₂ thin films were synthesized by a simple sol–gel method. The influence of polyethylene glycol (PEG) on the morphology and optoelectronic properties of the films was studied by addition of 1.0 g PEG in 10 ml precursor solution. The crystal sizes of the derived CuFeO₂ films with and without addition of PEG were 49 nm, but the sample with addition of PEG (labeled as CFO-PEG) showed weaker c-axis orientation growth. The sample without addition of PEG (labeled as CFO) showed a compact surface without detectable pores and had a thickness around 50 nm. However, the sample CFO-PEG exhibited a porous surface with worm-like grains in nanometric scale and had a thickness around 310 nm. Enhanced absorbance in UV–vis region was observed for the sample CFO-PEG which might ascribe to both the thickness and porous surface. The optical direct bandgaps at near-UV were estimated to be ~3.0 and 3.38 eV for the sample CFO-PEG and CFO, respectively. Though the porous surface of CFO-PEG has improved the absorbance in UV–vis region, the resistivity has also been increased due to the homogeneous distribution of interspaces between the worm-like grains, which makes the incident photon to current efficiency of CFO-PEG lower than that of CFO.     

Study of tri-layer antireflection coatings prepared by sol–gel method

Antireflective coatings (ARCs) on tri-layer thin film stacks were studied in this paper. Silica sols have been prepared by acid-catalyzed or base-catalyzed hydrolysis and condensation reactions of tetraethyl orthosilicate. Antireflective nanometric SiO₂/TiO₂ films are formed on both sides of the glass substrates by combining the sol–gel method and the dip-coating technique. Seen from the transmittance spectra of different films, a maximum light transmittance of 99.9% was obtained at the band of 300–800 nm. Scanning electron microscope (SEM) and atomic force microscopy (AFM) confirm the well-covered surface morphology. By the SEM observations we can see that the films are full of coverage on glass surface and containing no voids or cracks. The image root mean square roughness of the two types of ARCs provided by the AFM is 1.21 and 3.04 nm, respectively. Furthermore, a surface profiler was used to determine the thickness of each layer in the obtained multi-layer coating system.     

Physical and optical properties of organo-modified silica nanoparticles prepared by sol–gel

A comparative study on the physical and optical properties of silica nanoparticles prepared by sol–gel has been carried out. Post-modification of as-synthesized silica nanoparticles produced organo-functionalized silica nanoparticles slightly increased in size (~20%) and relatively high aggregation. However, in situ method produced sixfold bigger functionalized particles with good dispersion and less aggregation. Higher organic content was observed for in situ modified nanosilica, leading to a higher surface hydrophobicity that improved compatibility and dispersion in preparation of silica-polymer nanocomposite. Furthermore, in situ and post-modified nanosilica demonstrated a distinct optical activity, photoluminescence and UV compared to the unmodified nanoparticles.     

Thermal and luminescent properties of Eu2+-doped aluminates prepared by the sol–gel method

Alkaline earth aluminates with the overall nominal compositions Ca_0.5Sr_0.5Al₂O₄, Ca_0.5Mg_0.5Al₂O₄ and Mg_0.5Sr_0.5Al₂O₄ doped with 1 mol% of Eu²⁺ ions were prepared by the modified aqueous sol–gel method. The thermal behaviour of the xerogels was studied by the TG/DSC-MS technique under an argon and a reductive atmosphere (Ar/H₂–5 %). Appropriate luminescent efficiency of the materials was achieved after annealing at temperatures lower than those in conventional solid state reactions. All three aluminates are mixtures of at least two phases; the monoclinic phase of CaAl₂O₄, the hexagonal phase of SrAl₂O₄ and the cubic phase of MgAl₂O₄ were identified. Solid solubility was recognised in the Ca_0.5Sr_0.5Al₂O₄:Eu²⁺ composition due to the similar ionic radii of Ca²⁺ and Sr²⁺. UV excited luminescence was observed in the blue region (λ_max = 441 nm) in the aluminates containing the monoclinic phase of CaAl₂O₄ and in the green region (λ_max = 520 nm) in the Mg_0.5Sr_0.5Al₂O₄:Eu²⁺ composition.     

An investigation of the microstructure,optical and electrical properties of ZITO thin film using the sol–gel method

The multi-compound ZITO transparent conductive oxide (TCO) thin films were synthesized using the sol–gel method. The ZITO thin films with various volume ratios of ZnO to ITO (1:1, 2:1 and 9:1) were crystallized at different temperatures (600–700 °C). The results showed that the crystalline characteristics and optical transmittance were mainly dependent on ITO content and crystallization. Notably, the 650 °C Z₉ITO film not only had better conductivity but also possessed excellent optical transmittance. In addition, the surface roughness of the ZITO films and optoelectric properties of IZO (indium doped ZnO) films were analyzed to confirm the contribution of indium dopants on the optical transmittance. Also, the ZITO films were subjected to the effects of indium and tin dopants and this improved the related characteristics of ZnO films.     

Dielectric and energy storage properties of barium strontium titanate based glass–ceramics prepared by sol–gel method

Ba_0.6Sr_0.4TiO₃ based glass–ceramics were prepared by sol–gel process. Influences of B–Si–O glass content on the microstructure, dielectric, and energy storage properties of the BST based glass–ceramics have been investigated. Perovskite barium strontium titanate phase was found at annealing temperature 800 °C. A secondary phase Ba₂TiSi₂O₈ was detected and lowered by declining the mole ratio of element Si (from 50 to 25 mol%) in glass additive. Microstructural observation indicated that the microstructure homogeneity can be improved by glass addition till 2 mol%, while worsened by excessive glass concentrations. Due to relatively homogeneous microstructure, the maximum discharged energy density and breakdown strength were also obtained in samples with 2 mol% glass additive, which were found to be 0.553 J/cm³ and 43.2 kv/mm, respectively. Microscopic observation of the breakdown area was performed and the mechanical failure, including the formation and accumulation of micro-cracks during the dielectric breakdown process, was considered to be the main cause of dielectric breakdown. Results of the charging and discharging energy densities show that the BST based glass–ceramics prepared by sol–gel method has a potential for pulse power applications.     

Anticorrosive cerium-based coatings prepared by the sol–gel method

The development of efficient anti-corrosion and environmentally friendly coating systems are needed for the replacement of the highly toxic Cr-based conversion coatings for corrosion protection of aluminum alloys. In this study, we demonstrate that the direct application of ceramic cerium-based sol–gel coatings to AA7075-T6 substrates produces high-performance anti-corrosion layers. Electrochemical experiments and analyses of the microstructure demonstrate that the protective layers are very efficient for the passivation of the alloy surfaces operating as both passive and active barrier for corrosion protection.     

Synthesis and characterization of nitrogen-doped TiO2 nanoparticles prepared by sol–gel method

The N-doped TiO₂ has been synthesized by sol?Cgel method, using titanium isopropoxide, isopropanol and an aqueous solution of ammonia with ratio 2:1:10. The concentrations used for the NH₃ aqueous solution were 3, 7, 10 and 15?%. The samples have been analysed by X-ray diffraction, electron microscopy (SEM and TEM) thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), micro-Raman spectroscopy and diffuse reflectivity. TEM, SEM, DSC and TGA showed that the morphology is influenced by the presence of N^3? ions but not by the concentration of the solution. Instead reflectance gave us a relation between values of the energy gap and the concentration of N^3? ions: the gap between valence and conduction band lowers as the concentration of NH₃ in the starting solution increases. From these results we can say that the properties of the material have been tuned by doping with nitrogen ions because the particles absorb more light in the visible range, and this is important for photovoltaic and photocatalytic applications.     

Structural,dielectric and electrical properties of zinc doped nickel nanoferrites prepared by simplified sol–gel method

Zinc doped nickel ferrite nanoparticles having the general formula Ni_1−xZn_xFe₂O₄ (x = 0.1, 0.2, 0.3, 0.4, 0.5) were prepared with simplified sol–gel method. The structural and dielectric properties of these samples sintered at 750 ± 5 °C were studied. X-ray diffraction patterns confirm the single phase spinel structure for prepared samples. The scanning electron microscope images indicated that the particle size of the samples lies in the nanometer regime. The dielectric constant (ε_r) and dielectric loss tangent (tan δ) of nanocrystalline nickel ferrites were investigated as a function of frequency and Zn concentration. The dependence of ε_r and tan δ on the frequency of the alternating applied electric field is in accordance with the Maxwell–Wagner model. The prepared samples have a lowest dielectric constant compared to the already reported samples of the same composition to the best of our knowledge. The effect of Zn doping on the dielectric properties of nickel ferrites is explained on the basis of cations distribution in the crystal structure.     

Synthesis and characterization of hydroxyapatite obtained from different organic precursors by sol–gel method

The synthesis of four types of hydroxyapatite synthesized from calcium chloride and four different organic phosphites is presented. The method of synthesis chosen is the sol–gel route, which has a number of advantages compared to other methods, like the intimate contact between reactants and the milder synthesis conditions. The samples were thermally treated, the TG/DTG/DTA curves being obtained at four heating rates, namely: 7, 10, 12 and 15 °C min⁻¹. The samples were characterized before and after the thermal treatment using FT-IR analysis. The FT-IR spectra certified that the formed compounds represent hydroxyapatite. Based on the information from the TG curves and IR spectra interpretation, a reaction mechanism was proposed.     

The effect of heat treatment in the reducing atmosphere on the physical properties of TiO2 thin films prepared by sol–gel method

Multilayered nanostructured TiO₂ thin films were prepared by sol–gel and dipping deposition on quartz substrate followed by thermal treatment under reducing atmosphere (20 %H₂–80 %Ar). Heat treatment at progressively higher temperatures caused structural, morphological, and optical changes, which were investigated by X-ray diffraction (XRD), atomic force microscopy, scanning electron microscopy, and UV–Vis spectroscopy. The conductivities of the thin films were also measured by 4-point probe method. The XRD results showed that the calcined TiO₂ thin films consist of single anatase phase which was completely transformed into rutile phase after heat treatment at 1,000 °C. The grains of films grew by intra-agglomerate densification after heat treatment at higher temperatures. The root mean square roughness of the samples was found to be in the range of 0.58–3.36 nm. The partially reduced TiO₂ samples have red-shifted transmittance bands due to new energy band formed by oxygen vacancies. The electrical conductivity of the films was also enhanced after heat treatment in reducing atmosphere.     

The photocatalytic properties of Ti–Mo oxides prepared by a simple sol–gel route

Powders containing mixtures of titania and molybdite in different ratios were prepared by sol–gel processing. The sols were dried and subsequently calcined at 300, 500 and 700 °C. Depending on the ratio of Ti and Mo in the initial sol and the calcination temperature, Ti-doped MoO₃, TiO₂/MoO₃ or Mo-doped TiO₂ have been formed. The as prepared samples were characterised by scanning electron microscopy with attached X-ray dispersive energy analysis, X-ray diffractometry, Raman spectroscopy, gas adsorption and optical characterisation by ultraviolet/visible spectroscopy. The latter was used for the analysis of the photocatalytic properties on the decolourisation of methylene blue solutions under visible light irradiation. The phase composition, the specific surface and the photocatalytic activity were influenced by the molybdenum content and the calcination temperature. The final molybdenum content in the samples additionally depends on the calcination temperature. The optimum photocatalytic properties were observed or Ti-doped MoO₃.     

Structural and electrosurface characteristics of titanium dioxide xerogel prepared by the sol–gel method

Stable highly concentrated TiO₂ sol has been synthesized using binary titanyl ammonium sulfate monohydrate, (NH₄)₂TiO(SO₄)₂ · H₂O. Treatment of the sol with an ammonia solution has yielded a stable hydrogel, which, after being dried, is transformed into a TiO₂ xerogel. Study of the structure-related sorption and crystalline-chemical properties of the synthesized xerogel has shown that it represents a semicrystalline micro/mesoporous material with a rather developed specific surface area (S_sp = 120 m²/g). According to potentiometric titration data, the point of zero charge (PZC) of this material is located at pH 3.9. Measurements of the electrophoretic mobility (by microelectrophoresis) of TiO₂ xerogel particles in solutions of HCl, NaOH, and salts of mono-, bi-, and trivalent cations have shown that (1) the isoelectric point (IEP) of the particles lies in the vicinity of pH 6.2, i.e., at a much higher pH than that for PZC; (2) the presence of increasing amounts of 1: 1 and 2: 1 electrolytes causes a gradual and a dramatic reduction in the ζ potential of the particles, respectively; and (3), in the presence of an electrolyte with a trivalent counterion, the surface charge is reversed. The behavior of TiO₂ xerogel in an electric field is similar to that of lyophobic particles, with the difference that there is no maximum in the ζ potential versus 1: 1 electrolyte concentration dependence and the measured IEP of the xerogel is much higher than its PZC. Possible reasons for this discrepancy have been discussed.