Low driving voltage in organic light-emitting diode using MoO3/NPB multiple quantum well structure in hole transport layer

Driving voltage of organic light-emitting diode (OLED) is lowered by employing molybdenum trioxide (MoO₃)/N, N'-bis(naphthalene-1-yl)-N,N'-bis(phe-nyl)-benzidine (NPB) multiple quantum well (MQW) structure in hole transport layer. For the device with double quantum well (DQW) structure of ITO/ [MoO₃ (2.5 nm)/NPB (20 nm)]₂/Alq₃(50 nm)/LiF (0.8 nm)/Al (120 nm)], the turn-on voltage is reduced to 2.8 V, which is lowered by 0.4 V compared with that of the control device (without MQW structures), the driving voltage is 5.6 V, which is reduced by 1 V compared with that of the control device at the 1000 cd/m². In this work, the enhancement of the injection and transport ability for holes could reduce the driving voltage for the device with MQW structure, which is attributed not only to the reducing energy barrier between ITO and NPB, but also to the forming charge transfer complex between MoO₃ and NPB induced by the interfacial doping effect of MoO₃.     

利用NPB/MoO3/NpB作为空穴传输层的低驱动电压的有机发光器件

通过引入(NPB/MoO3)x/NPB作为空穴传输层,获得了低驱动电压的有机电致发光器件(OLEDs),(NPB/MoO3)x为多层结构(x为0,1和2).通过对比发现,在相同亮度下,x=1对应的器件具有最低的工作电压.这是由于在NPB和MoO3之间产生了电荷转移复合物(charge transfer,CT),这将会降低器件的空穴注入势垒,从而降低其工作电压,文中所研究器件为基于8-羟基喹啉铝(tris(8-hydroxyquino-line)aluminum,Alq3)的绿光器件.与x=0时的普通器件相比,在亮度为1 000 cd·m-2时,x=1时的工作电压降低了 0.8 V.     

Luminescence properties of type-II quantum well light-emitting diodes formed with NPB and Alq3

The organic quantum well devices which are similar to the type-II quantum well of inorganic semiconductor have been fabricated. In the electroluminescence, the blue shift of spectrum with increasing applied voltage is observed, which is interpreted by exciton confinement effect and polarization effect, and the generation of exciton, including carrier injection and energy transfer, is discussed. This energy transfer from barrier to well is studied by photoluminescence and is interpreted in terms of Förster energy transfer. The electromodulation of photoluminescence demonstrates the quenching mainly comes from the dissociation of exciton in NPB and that in Alq₃ is very stable.     

InGaN/GaN multiple quantum well solar cells with an enhanced open-circuit voltage

In this paper,InGaN/GaN multiple quantum well solar cells (MQWSCs) with an In content of 0.15 are fabricated and studied.The short-circuit density,fill factor and open-circuit voltage (V oc) of the device are 0.7 mA/cm 2,0.40 and 2.22 V,respectively.The results exhibit a significant enhancement of V oc compared with those of InGaN-based hetero and homojunction cells.This enhancement indicates that the InGaN/GaN MQWSC offers an effective way for increasing V oc of an In-rich In x Ga 1 x N solar cell.The device exhibits an external quantum efficiency (EQE) of 36% (7%) at 388 nm (430 nm).The photovoltaic performance of the device can be improved by optimizing the structure of the InGaN/GaN multiple quantum well.     

Improving efficiency of organic light-emitting devices by optimizing the LiF interlayer in the hole transport layer

The efficiency of organic light-emitting devices (OLEDs) based on N,N'-bis(1-naphthyl)-N,N'-diphenyl-N,1'-biphenyl-4,4'-diamine (NPB) (the hole transport layer) and tris(8-hydroxyquinoline) aluminum (Alq₃) (both emission and electron transport layers) is improved remarkably by inserting a LiF interlayer into the hole transport layer. This thin LiF interlayer can effectively influence electrical performance and significantly improve the current efficiency of the device. A device with an optimum LiF layer thickness at the optimum position in NPB exhibits a maximum current efficiency of 5.96 cd/A at 215.79 mA/cm², which is about 86% higher than that of an ordinary device (without a LiF interlayer, 3.2 cd/A). An explanation can be put forward that LiF in the NPB layer can block holes and balance the recombination of holes and electrons. The results may provide some valuable references for improving OLED current efficiency.     

Reduction of driving voltage in organic light-emitting diodes with molybdenum trioxide in CuPc/NPB interface

A novel structure of organic light-emitting diode was fabricated by inserting a molybdenum trioxide (MoO₃) layer into the interface of hole injection layer copper phthalocyanine (CuPc) and hole transport layer N,N′-diphenyl-N,N′-bis(1-napthyl-phenyl)-1,1′-biphenyl-4,4′-diamine (NPB). It has the configuration of ITO/CuPc(10 nm)/MoO₃(3 nm)/NPB(30 nm)/ tris-(8-hydroxyquinoline) aluminum (Alq₃)(60 nm)/LiF(0.5 nm)/Al. The current density-voltage-luminance (J-V-L) performances show that this structure is beneficial to the reduction of driving voltage and the enhancement of luminance. The highest luminance increased by more than 40% compared to the device without hole injection layer. And the driving voltage was decreased obviously. The improvement is ascribed to the step barrier theory, which comes from the tunnel theory. The power efficiency was also enhanced with this novel device structure. Finally, “hole-only” devices were fabricated to verify the enhancement of hole injection and transport properties of this structure.     

The performance enhancement in organic light-emitting diode using a semicrystalline composite for hole injection

A semicrystalline composite, 3, 4, 9, 10 perylenetetracarboxylic dianhydride （PTCDA） doped N,N＇-di（1-naphthyl）- N,N＇-diphenylbenzidine （NPB）, has been fabricated and characterized. An organic light-emitting diode using such a composite in hole injection exhibits the improved performance as compared with the reference device using neat NPB in hole injection. For example, at a luminance of 2000 cd/m2, the former device gives a current efficiency of 2.0cd/A, higher than 1.6cd/A obtained from the latter device. Furthermore, the semicrystalline composite has been shown thermally to be more stable than the neat NPB thin film, which is useful for making organic light emitting diodes with a prolonged lifetime.     

InGaAsP multiple quantum well edge-emitting light-emitting diode showing low coherence characteristics using selective-area metalorganic vapor phase epitaxy

Low coherence multiple-quantum well edge-emitting light-emitting diodes were obtained using selective-area metalorganic vapor-phase epitaxial growth, which utilized growth rate enhancement on an open stripe region between mask stripes. An optical absorption region, which was controlled by selective-area growth, was introduced to suppress optical feedback. At a driving current of 100 mA and an ambient temperature of 25°C, a power of 55 μW was coupled into a single-mode fiber, and a broad spectrum without spectral ripple was observed. Low coherence characteristics and very small temperature dependence were obtained in the temperature range from -40°C to 85°C. The modulation bandwidth was 210 MHz at a bias current of 100 mA.     

In组分渐变提高InGaN/GaN多量子阱发光二极管发光性能

利用金属有机物化学气相沉积系统在蓝宝石衬底上通过有源层的变温生长,得到In组分渐变的量子阱结构,从而获得具有三角形能带结构的InGaN/GaN多量子阱发光二极管(LED)(简称三角形量子阱结构LED).变温光致发光谱结果表明,相对于传统具有方形能带结构的量子阱LED(简称方形量子阱结构LED),三角形量子阱结构有效提高了量子阱中电子和空穴波函数的空间交叠,从而增加了LED的内量子效率;电致发光谱结果表明,三角形量子阱结构LED器件与传统结构LED器件相比,明显改善了发光峰值波长随着电流的蓝移现象.通过以上     

Blue organic light-emitting diodes with low driving voltage and maximum enhanced power efficiency based on buffer layer MoO3

Blue organic light-emitting devices based on wide bandgap host material, 2-(t-butyl)-9, 10-di-(2-naphthyl) anthracene (TBADN), blue fluorescent styrylamine dopant, p-bis(p-N,N-diphenyl-amino-styryl)benzene (DSA-Ph) have been realized by using molybdenum oxide (MoO₃) as a buffer layer and 4,7-diphenyl-1,10-phenanthroline (BPhen) as the ETL. The typical device structure used was glass substrate/ITO/MoO₃ (5 nm)/NPB (30 nm)/[TBADN: DSA-Ph (3 wt%)](35 nm)/BPhen (12 nm)/LiF (0.8 nm)/Al (100 nm). It was found that the MoO₃∥BPhen-based device shows the lowest driving voltage and highest power efficiency among the referenced devices. At the current density of 20 mA/cm², its driving voltage and power efficiency are 5.4 V and 4.7 Lm/W, respectively, which is independently reduced 46%, and improved 74% compared with those the m-MTDATA∥Alq₃ is based on, respectively. The J-V curves of ‘hole-only’ devices reveal that a small hole injection barrier between MoO₃∥NPB leads to a strong hole injection, resulting low driving voltage and high power efficiency. The results strongly indicate that carrier injection ability and balance shows a key significance in OLED performance.     

Increased performance of an organic light-emitting diode by employing a zinc phthalocyanine based composite hole transport layer

We demonstrate that the electroluminescent performances of organic light-emitting diodes are significantly improved by employing a zinc phthalocyanine （ZnPc）-based composite hole transport layer （c-HTL）. The optimum ris-（8-hydroxyquinoline）aluminum （Alq3）-based organic light-emitting diode with a c-HTL exhibits a lower turn-on voltage of 2.8 V, a higher maximum current efficiency of 3.40 cd/A and a higher maximum power efficiency of 1.91 lm/W, which are superior to those of the conventional device （turn-on voltage of 3.8 V, maximum current efficiency of 2.60 cd/A, and maximum power efficiency of 1.21 lm/W）. We systematically studied the effects of different kinds of N’-diphenyl-N,N’-bis（1-naphthyl）（1,1’-biphenyl）-4,4’diamine （NPB）：ZnPc c-HTL. Meanwhile, we also investigate their mechanisms different from that in the case of using ZnPc as buffer layer. The specific analysis is based on the absorption spectra of the hole transporting material and current density–voltage characteristics of the corresponding hole-only devices.     

Lowering the driving voltage and improving the luminance of blue fluorescent organic light-emitting devices by thermal annealing a hole injection layer of pentacene

We chose pentacene as a hole injection layer (HIL) to fabricate the high performance blue fluorescent organic light-emitting devices (OLEDs). We found that the carrier mobility of the pentacene thin films could be efficiently improved after a critical annealing at temperature 120 °C. Then we performed the tests of scanning electron microscopy, atomic force microscopy, and Kelvin probe to explore the effect of annealing on the pentacene films. The pentacene film exhibited a more crystalline form with better continuities and smoothness after annealing. The optimal device with 120 ℃ annealed pentacene film and n-doped electron transport layer (ETL) presents a low turn-on voltage of 2.6 V and a highest luminance of 134800 cd/m² at 12 V, which are reduced by 26% and improved by 50% compared with those of the control device.     

Light hole transport in a strained GaAs/In0.18Ga0.82As quantum well at high pressures

Abstract

Here we report what we believe to be the first observation of the pressure dependence of the light hole behavior in a modulation doped In_0.18Ga_0.82As/GaAs single strained quantum well grown by MBE. Transport measurements have been undertaken as a function of temperature (4–300K) and hydrostatic pressure (4–8kbar). Hole mobilities of ～17000 cm²/Vs have been obtained for sheet carrier densities of ～3.3×10¹¹ cm^?2. At low temperatures (<100K) persistent photogenerated holes have been observed. The hole mobility is found to decrease with increasing pressure at a rate intermediate between that typically observed for holes and electrons in bulk III-V semiconductors.     

Improved efficiency droop characteristics in an InGaN/GaN light-emitting diode with a novel designed last barrier structure

<正>In this study,the characteristics of nitride-based light-emitting diodes with different last barrier structures are analysed numerically.The energy band diagrams,electrostatic field near the last quantum barrier,carrier concentration in the quantum well,internal quantum efficiency,and light output power are systematically investigated.The simulation results show that the efficiency droop is markedly improved and the output power is greatly enhanced when the conventional GaN last barrier is replaced by an AlGaN barrier with Al composition graded linearly from 0 to 15% in the growth direction.These improvements are attributed to enhanced efficiencies of electron confinement and hole injection caused by the lower polarization effect at the last-barrier/electron blocking layer interface when the graded Al composition last barrier is used.     

Enhanced charge carrier injection in heterojunction organic field-effect transistor by inserting an MoO3 buffer layer

A top-contact organic field-effect transistor(OFET) is fabricated by adopting a pentacene/1,1’-bis(di-4tolylaminophenyl) cyclohexane(TAPC) heterojunction structure and inserting an MoO3 buffer layer between the TAPC organic semiconductor layer and the source/drain electrode.The performances of the heterojunction OFET,including output current,field-effect mobility,and threshed voltage,are all significantly improved by introducing the MoO3 thin buffer layer.The performance improvement of the modified heterojunction OFET is attributed to a better contact formed at the Au/TAPC interface due to the MoO3 thin buffer layer,thereby leading to a remarkable reduction of the contact resistance at the metal/organic interface.     

Effects of a prestrained InGaN interlayer on the emission properties of InGaN/GaN multiple quantum wells in a laser diode structure

The electroluminescence (EL) and photoluminescence (PL) spectra of InGaN/GaN multiple quantum wells (MQWs) with a prestrained InGaN interlayer in a laser diode structure are investigated. When the injection current increases from 5 mA to 50 mA, the blueshift of the EL emission peak is 1 meV for the prestrained sample and 23 meV for a control sample with the conventional structure. Also, the internal quantum efficiency and the EL intensity at the injection current of 20 mA are increased by 71% and 65% respectively by inserting the prestrained InGaN interlayer. The reduced blueshift and the enhanced emission are attributed mainly to the reduced quantum-confined Stark effect (QCSE) in the prestrained sample. Such attributions are supported by the theoretical simulation results, which reveal the smaller piezoelectric field and the enhanced overlap of electron and hole wave functions in the prestrained sample. Therefore, the prestrained InGaN interlayer contributes to strain relaxation in the MQW layer and enhancement of light emission due to the reduction of QCSE.     

Exciplex elimination in an organic light-emitting diode based on a fluorene derivative by inserting 4,4’-N,N’-dicarbazole-biphenyl into donor/acceptor interface

Organic light-emitting diodes (OLEDs) composed of a novel fluorene derivative of 2,3-bis(9,9-dihexyl-9H-fluoren-2-yl)-6,7-difluoroquinoxaline (F2Py) were fabricated, and exciplex emission was observed in the device. To depress the exciplex in an OLED for pure colour light emission, 4, 4'-N,N'-dicarbazole-biphenyl (CBP) was inserted as a separator at the donor/acceptor interface. It was found that the device without the CBP layer emitted a green light peaking at 542~nm from the exciplex and a shoulder peak about 430~nm from F2Py. In contrast, the OLED with CBP layer emitted only a blue light peak at about 432~nm from F2Py. Device efficiencies were calculated by a simulative mode in an injection controlled type mechanism, and the results showed that exciplexes yield much lower quantum efficiency than excitons. The device with CBP has a higher power efficiency as no exciplex was present.     

Fabrication and optical properties of InGaN/GaN multiple quantum well light emitting diodes with amorphous BaTiO3 ferroelectric film

BaTiO3 （BTO） ferroelectric thin films are prepared by the sol,el method. The fabrication and the optical properties of an InGaN/GaN multiple quantum well light emitting diode （LED） with amorphous BTO ferroelectric thin film are studied. The photolumineseence （PL） of the BTO ferroelectric film is attributed to the structure. The ferroeleetric film which annealed at 673 K for 8 h has the better PL property. The peak width is about 30 nm from 580 nm to 610 nm, towards the yellow region. The mixed electroluminescence （EL） spectrum of InGaN/GaN multiple quantum well LED with 150-nm thick amorphous BTO ferroelectric thin film displays the blue-white light. The Commission Internationale De L＇Eclairage （CIE） coordinate of EL is （0.2139, 0.1627）. EL wavelength and intensity depends on the composition, microstructure and thickness of the ferroelectric thin film. The transmittance of amorphous BTO thin film is about 93% at a wavelength of 450 nm-470 nm. This means the amorphous ferroelectrie thin films can output more blue-ray and emission lights. In addition, the amorphous ferroelectric thin films can be directly fabricated without a binder and used at higher temperatures （200 ℃-400 ℃）. It is very favourable to simplify the preparation process and reduce the heat dissipation requirements of an LED. This provides a new way to study LEDs.     

Performance improvement in pentacene organic thin film transistors by inserting a C60 ultrathin layer

The contact effect on the performances of organic thin film transistors is studied here. A C₆₀ ultrathin layer is inserted between Al source--drain electrode and pentacene to reduce the contact resistance. By a 3 nm C₆₀ modification, the injection barrier is lowered and the contact resistance is reduced. Thus, the field-effect mobility increases from 0.12 to 0.52 cm²/(V·s). It means that inserting a C₆₀ ultra thin layer is a good method to improve the organic thin film transistor (OTFT) performance. The output curve is simulated by using a charge drift model. Considering the contact effect, the field effect mobility is improved to 1.15 cm²/(V·s). It indicates that further reducing the contact resistance of OTFTs should be carried out.