The interaction between a screw dislocation and an interfacial cruciform crack and collinear linear cracks

The interaction between a screw dislocation and an interfacial cruciform crack and collinear linear cracks under loads at infinity was investigated. General solutions of complex potentials to this problem were derived by using complex potential theory. As illustrative examples, the closed form solution for a screw dislocation interacting with an interfacial cruciform crack and a linear crack is obtained. The stress intensity factor and critical stress intensity factor for dislocation emission are also calculated. The results show that the shielding effect increases with the increase of the shear modulus and the distance between the two cracks, but it decreases with the increase of dislocation azimuth and the distance between the dislocation and the cruciform crack tip. The critical loads at infinity for dislocation emission increase with the increment of the emission angle, the distance the two cracks and the vertical length of the cruciform crack.     

Shielding effect and emission criterion of a screw dislocation near an interfacial blunt crack

Shielding effect and emission criterion of a screw dislocation near an interfacial blunt crack are dealt with in this paper. Utilizing the conformal mapping technique, the closed-form solutions are derived for complex potentials and stress fields due to a screw dislocation located near the interfacial blunt crack. The stress intensity factor on the crack tips and the critical stress intensity factor for dislocation emission are also calculated. The influence of the orientation of the dislocation and the morphology of the blunt crack as well as the material elastic dissimilarity on the shielding effect and the emission criterion is discussed in detail. The results show that positive screw dislocations can reduce the stress intensity factor of the interfacial blunt crack tip (shielding effect). The shielding effect increases with the increase of the shear modulus of the lower half-plane, but it decreases with the increase of the dislocation azimuth angle. The critical loads at infinity for dislocation emission increases with the increase of emission angle and curvature radius of blunt crack tip, and the most probable angle for screw dislocation emission is zero. The present solutions contain previous results as special cases.     

Shielding effect of a nano-circular inclusion acting on semi-infinite wedge cracks

The model of a screw dislocation near a semi-infinite wedge crack tip inside a nano-circular inclusion is proposed to investigate the shielding effect of nano inclusions acting on cracks. Utilizing the complex function method, the closed-form solutions of the stress fields in the matrix and the inclusion region are derived. The stress intensity factor, the image force, as well as the critical loads for dislocation emission are discussed in detail. The results show that the nano inclusion not only enhances the shielding effect exerted by the dislocation, but also provides a shielding effect itself. Moreover, dislocations may be trapped in the nano inclusion even if the matrix is softer than the inclusion. This helps the dislocation shield crack, and reduces the dislocation density within the matrix.     

磁电弹性体中多条位错与Griffith裂纹

根据本征方程，研究磁电弹性体中若干平行螺型位错与Griffith裂纹的相互作用.结合Muskhelishvili方法和算子理论，得到磁电弹性体中由位错和裂纹所诱导的应力场、电场和磁场的解析解.数值算例表明：在裂纹的端点及位错点上仍然存在应力的奇异性，离位错点越远处广义力越小，结论与已有的结果相符，证明了结论的正确性.当位错点与裂纹端点距离越近时，裂纹与位错间的应力场越小，并逐渐趋近于零.     

The elastic field of general-shape 3-D cracks

We extend here the Bilby-Eshelby approach of 2-D crack representation with dislocation pileups to treat 3-dimensional cracks of general geometry. Cracks of any specified external bounding 3-D contour under general loading conditions are represented by sets of parametric Somigliana loops that satisfy total (interaction, self, and external) force equilibrium. Loop positions are solved by using a time integration scheme till equilibrium is achieved. The local Burgers vector is suitably adjusted to be proportional to the local applied surface traction on the crack. The developed method is computationally advantageous, since accurate crack stress fields are obtained with very few concentric parametric loops that adjust to the external crack shape and the local force conditions. The method is tested against known elasticity solutions for 3-D cracks and found to be convergent with an increase in the number of pileup dislocation loops. The method is applied to the determination of the stress field around a 3-D Griffith crack under general loading and a grain boundary crack before and after branching.     

Dislocation emission from an elliptically blunted crack tip with surface effects

The explicit expressions for critical stress intensity factors are derived for edge dislocation emission from an elliptically blunt crack with surface effects under mode I and mode II loadings. The influence of surface effects on dislocation emission criterion is analyzed. The result indicates the impact of the surface stress becomes remarkable for nanoscale blunted cracks and some particular materials, which cannot only affect the value of the critical stress intensity factors for dislocation emission, but also alter the emission angle.     

晶体相场法研究应力状态及晶体取向对微裂纹尖端扩展行为的影响

采用晶体相场模拟研究了单向拉伸作用下初始应力状态、晶体取向角度对单晶材料内部微裂纹尖端扩展行为的影响, 以(111)晶面上的预制中心裂纹为研究对象探讨了微裂纹尖端扩展行为的纳观机理, 结果表明: 微裂纹的扩展行为主要发生在<011>(111)滑移系上, 扩展行为与扩展方向与材料所处的初始应力状态及晶体取向紧密相关. 预拉伸应力状态将首先诱发微裂纹尖端生成滑移位错, 进而导致晶面解理而实现微裂纹尖端沿[011]晶向扩展, 扩展到一定程度后由于位错塞积, 应力集中, 使裂纹扩展方向沿另一滑移方向[101], 并形成锯齿形边缘; 预剪切应力状态下, 微裂纹尖端首先在[101]晶向解理扩展, 并诱发位错产生, 形成空洞聚集型长大的二次裂纹, 形成了明显的剪切带; 预偏变形状态下微裂纹尖端则直接以晶面解理形式[101]在上进行扩展, 直至断裂失效; 微裂纹尖端扩展行为随晶体取向不同而不同, 较小的取向角度会在裂纹尖端形成滑移位错, 诱发空位而形成二次裂纹, 而较大的取向角下的裂纹尖端则以直接解理扩展为主, 扩展方向与拉伸方向几近垂直.     

Elastic behaviour of an edge dislocation near a sharp crack emanating from a semi-elliptical blunt crack

The interaction between an edge dislocation and a crack emanating from a semi-elliptic hole is dealt with. Utilizing the complex variable method, closed form solutions are derived for complex potentials and stress fields. The stress intensity factor at the tip of the crack and the image force acting on the edge dislocation are also calculated. The influence of the morphology of the blunt crack and the position of the edge dislocation on the shielding effect to the crack and the image force is examined in detail. The results indicate that the shielding or anti-shielding effect to the stress intensity factor increases acutely when the dislocation approaches the tip of the crack. The effect of the morphology of the blunt crack on the stress intensity factor of the crack and the image force is very significant.     

一维六方准晶中螺形位错与楔形裂纹的相互作用

采用保角映射方法和扰动技巧,研究了一维六方准晶中螺形位错和半无限楔形裂纹的相互作用. 讨论了位错的位置和楔形角对作用在位错上的力的影响,得到了应力强度因子和作用在 位错上的力的解析解.此外,还详细地讨论了位错对裂纹的影响.当楔形角参数λ=1/2时, 半无限楔形裂纹退化成半无限尖裂纹,相应的结果 可以作为特殊情况而直接得到.     

磁电弹性体中螺型位错与唇口裂纹的相互作用

研究磁电弹性体中螺型位错与唇口裂纹的相互作用。结合Muskhelishvili方法和干扰技术, 在假定裂纹面具有不可渗透条件下得到磁电弹性体中由位错和唇口裂纹所诱导的应力场、电场和磁场的解析解。应用广义Peach-Koehler公式,得到作用在位错上的影像力。通过数值算例,得到场强度因子的变化规律及影像力和广义力随位错位置的变化规律。     

Detection of cracking and damage mechanisms in brittle granites by moment tensor analysis of acoustic emission signals

An acoustic emission (AE) testing of rock cracking was performed under uniaxial loading conditions by precut varisized circular holes in selected brittle granites. Based on AE-source location technique and AE-theory for moment tensor analysis, rules of the temporal–spatial evolution of micro-cracks in different failure mechanisms were explored and types of micro-cracks were analyzed as well. The results revealed that the micro-cracks are uniquely easy to generate in the positions where stress are concentrated. Tensile fractures are easy to form on the roof and floor of a circular hole, while shear fractures are easy to be found on both sides. The locations of initial cracks generated around the holes in the loading process are the direction or vertical direction of maximum principle stress. Macroscopic crack orientation agrees with the direction of maximum principle stress approximately. As the size of circular opening increases and the relative size of pillar decreases, shear cracks are dominant with the percentage more than 45%, tension cracks are fewer, accounted for less than 40% of the total events, and mixed-mode cracks represent a minimum proportion, despite the decrease of percentage of shear cracks. The findings of this work can serve for supporting design of tunnel or roadway to avoid collapse.     

体心立方金属钽Ⅱ型裂纹尖端缺陷萌生的多尺度分析

本文采用多尺度准连续介质法(quasi-continuum method, QC)模拟体心立方(body-centered-cubic, bcc)金属钽(Ta)Ⅱ型裂纹尖端位错的形核与发射过程,获得位错发射位置与应力强度因子关系曲线,分析裂纹尖端缺陷萌生过程,研究全位错分解以及扩展位错形成机理. 位错活动在不同阶段表现出不一致的特征,新位错的发射对于位错运动具有促进作用. 研究表明,裂纹扩展初始阶段首先萌生点缺陷,点缺陷随着加载强度增加会萌生新的点缺陷,点缺陷最终运动到边界,导致Ⅱ型断裂破坏. 在全位错发射之前有不全位错的形核与发射表明全位错的分解分步进行,从势能曲线上来看,也就是两个极小值点的形成机理不同. 关键词： 多尺度 准连续介质法 Ⅱ型裂纹 扩展位错     

Crack-stimulated generation of deformation twins in nanocrystalline metals and ceramics

A theoretical model is proposed that describes the generation of deformation twins near brittle cracks of mixed I and II modes in nanocrystalline metals and ceramics. In the framework of the model, a deformation twin nucleates through stress-driven emission of twinning dislocations from a grain boundary distant from the crack tip. The emission is driven by both the external stress concentrated by the pre-existent crack and the stress field of a neighbouring extrinsic grain boundary dislocation. The ranges of the key parameters, the external shear stress, τ, and the crack length, L, are calculated within which the deformation-twin formation near pre-existent cracks is energetically favourable in a typical nanocrystalline metal (Al) and ceramic (3C-SiC). The results of the proposed model account for experimental data on observation of deformation twins in nanocrystalline materials reported in the literature. The deformation-twin formation is treated as a toughening mechanism effectively operating in nanocrystalline metals and ceramics.     

Analytical solutions for some defect problems in 1D hexagonal and 2D octagonal quasicrystals

We study some typical defect problems in one-dimensional (1D) hexagonal and two-dimensional (2D) octagonal quasicrystals. The first part of this investigation addresses in detail a uniformly moving screw dislocation in a 1D hexagonal piezoelectric quasicrystal with point group 6mm. A general solution is derived in terms of two functions φ ₁, φ ₂, which satisfy wave equations, and another harmonic function φ ₃. Elementary expressions for the phonon and phason displacements, strains, stresses, electric potential, electric fields and electric displacements induced by the moving screw dislocation are then arrived at by employing the obtained general solution. The derived solution is verified by comparison with existing solutions. Also obtained in this part of the investigation is the total energy of the moving screw dislocation. The second part of this investigation is devoted to the study of the interaction of a straight dislocation with a semi-infinite crack in an octagonal quasicrystal. Here the crack penetrates through the solid along the period direction and the dislocation line is parallel to the period direction. We first derive a general solution in terms of four analytic functions for plane strain problem in octagonal quasicrystals by means of differential operator theory and the complex variable method. All the phonon and phason displacements and stresses can be expressed in terms of the four analytic functions. Then we derive the exact solution for a straight dislocation near a semi-infinite crack in an octagonal quasicrystal, and also present the phonon and phason stress intensity factors induced by the straight dislocation and remote loads.      

Dislocation-crack interaction

In this paper, recent developments in the understanding of the dislocation-crack interaction and its relationship to the phenomena of crack tip deformation and fracture toughness are reviewed. An enhanced research activity in this area began with successful observations of the behavior of crack tip dislocations by various techniques, namely etch pits technique, X-ray topography and transmision electron microscopy. The advantages and limitations of these techniques are compared and the information obtained from these experiments are discussed. The results show that dislocations are emitted from a crack tip when the applied stress is sufficiently high. During crack propagation, dislocations are also generated from other bulk sources and the number of these dislocations relative to those from the crack tip may be an important parameter. The elastic theory of the interaction between dislocations and a crack is presented by considering the force on the dislocations. The theory is applied to derive a dislocation emission condition, which may be expressed in terms of a critical stress intensity factor. It is concluded that the dislocations emitted from a crack tip are repelled from the crack tip and this repulsive interaction is responsible for the formation of a dislocation-free zone. These dislocations shield the crack tip from the applied stress and hence contribute to an increase in the fracture toughness. The physical origin of the dislocation-free zone lies in the presence of a barrier to dislocation emission from the crack tip. One of the barriers to dislocation emission is the image stress. With the dislocation-free zone, the crack tip can maintain a finite stress intensity factor following crack tip deformation. The lattice theories of dislocation-crack interaction indicate that the results are consistent with those of the continuum theory.     

Kim model for stress distribution in a hollow cylindrical superconductor

In the present work, the distributions of the stress induced by flux pinning in a cylindrical superconductor with a concentric elliptic hole are studied. The Kim model is considered for the critical state, and the analytical expression of the stress in the cylinder is derived when the concentric hole is circular. Based on the finite element method, at first, the validity of the calculation process and the accuracy of the numerical results are proved by comparing with the analytical results. Subsequently, the distributions of the stress are obtained for different ratio of the major axis and the minor axis of the elliptic hole. It is found that due to the effect of stress concentration, as the value of ratio the major axis and the minor axis becomes large, the radial and hoop stress in superconductor just increase significantly in the vicinity of the hole, and the variation of the hoop stress is more sensitive. These results have significant effects on the safety in applications of superconductor.     

Exact analytic solutions for an elliptic hole with asymmetric collinear cracks in a one-dimensional hexagonal quasi-crystal

Using the complex variable function method and the technique of conformal mapping, the anti-plane shear problem of an elliptic hole with asymmetric colfinear cracks in a one-dimensional hexagonal quasi-crystal is solved, and the exact analytic solutions of the stress intensity factors （SIFs） for mode Ⅲ problem are obtained. Under the limiting conditions, the present results reduce to the Griffith crack and many new results obtained as well, such as the circular hole with asymmetric collinear cracks, the elliptic hole with a straight crack, the mode T crack, the cross crack and so on. As far as the phonon field is concerned, these results, which play an important role in many practical and theoretical applications, are shown to be in good agreement with the classical results.     

The interaction between a screw dislocation and a wedge-shaped crack in one-dimensional hexagonal piezoelectric quasicrystals

Based on the fundamental equations of piezoelasticity of quasicrystal material,we investigated the interaction between a screw dislocation and a wedge-shaped crack in the piezoelectricity of one-dimensional hexagonal quasicrystals.Explicit analytical solutions are obtained for stress and electric displacement intensity factors of the crack,as well as the force on dislocation.The derivation is based on the conformal mapping method and the perturbation technique.The influences of the wedge angle and dislocation location on the image force are also discussed.The results obtained in this paper can be fully reduced to some special cases already available or deriving new ones.     

二元晶体中缺陷所引起的位移畴

借助于应变晶体的弹性偶极子模型,把二元晶体中的每一个原子都视为一弹性偶极子。它们有不同的等效偶极矩,在晶体内其他强内应力源,如位错、包裹物等所产生的应力场中受到不同的作用力,因而产生不同的位移,形成了不同形状的畴。它决定于永久偶极矩及感生偶极矩的相对大小和内应力源所产生的应力场的分布。本文分别给出了二元晶体中在刃位错、螺位错、包裹物和挤列等的应力场作用下出现的畴图样。它们呈各种形式排列的花瓣状图形。在适当的条件下,它们可以被观察到。结果还表明了压力对相变的影响。 关键词：     

Localization of plastic strain under shock-wave loading of titanium alloy with a crack

The effect of shock-wave loading with an amplitude of 4 GPa and a duration of 10 μs on the localization of plastic flow and the dynamic fracture of VT-1 cast titanium alloy containing a disk-shaped crack is considered. It is found that the crack size decreases in the direction of shock wave propagation, the dislocation density grows and adiabatic shear bands appear near the crack, and secondary cracks originate in the areas of localized flow near the crack edges. The strain, strain rate, dislocation density, rate of dislocation generation, and dislocation velocity near and away from the healing crack are estimated.