Conductivity in alkylamine/gold and alkanethiol/gold molecular junctions measured in molecule/nanoparticle/molecule bridges and conducting probe structures

Charge transport through alkane monolayers on gold is measured as a function of molecule length in a controlled ambient using a metal/molecule/nanoparticle bridge structure and compared for both thiol and amine molecular end groups. The current through molecules with an amine/gold junction is observed to be more than a factor of 10 larger than that measured in similar molecules with thiol/gold linkages. Conducting probe atomic force microscopy is also used to characterize the same monolayer systems, and the results are quantitatively consistent with those found in the nanoparticle bridge geometry. Scaling of the current with contact area is used to estimate that approximately 100 molecules are probed in the nanoparticle bridge geometry. For both molecular end groups, the room-temperature conductivity at low bias as a function of molecule length shows a reasonable fit to models of coherent nonresonant charge tunneling. The different conductivity is ascribed to differences in charge transfer and wave function mixing at the metal/molecule contact, including possible effects of amine group oxidation and molecular conformation. For the amine/Au contact, the nitrogen lone pair interaction with the gold results in a hybrid wave function directed along the molecule bond axis, whereas the thiol/Au contact leads to a more localized wave function.     

Unmodified supported thiol/lipid bilayers: studies of structural disorder and conducting mechanism by cyclic voltammetry and AC impedance.

Supported thiol/lipid bilayer assembly, one of the most spectacular bilayer systems in recent years, has provided a good model to study biomembranes because of its high mechanical stability. In this work, the structural and conducting property of unmodified Au supported octadecanethiol/phosphatidylcholine bilayers were investigated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The forming process of bilayer was monitored by capacitance plane plot. The normalized membrane capacitance of supported bilayer is 0.52 microF cm(-2). Kinetically controlled voltammograms determined by Butler-Volmer equation were obtained for both thiol monolayer and thiol/lipid bilayer in linear sweep voltammetry. Results of EIS experiment indicate that collapsed sites and pinhole defects exist in thiol monolayer and lipid monolayer, respectively. The difference between the values of experimental and theoretical standard electron transfer rate constant indicates that the conducting mechanism of Au supported thiol monolayer is electron tunneling at collapsed sites. The conducting mechanism of Au supported thiol/lipid bilayer is attributed as the following: the electroactive species could diffuse through pinholes in the lipid monolayer and reach collapsed sites in thiol monolayer, where electron transfer occurs via a tunneling process. The fractional coverage of the lipid monolayer measure by EIS experiments is about 0.98 or higher.     

Correlation between HOMO alignment and contact resistance in molecular junctions: aromatic thiols versus aromatic isocyanides

Understanding electron transport in metal-molecule-metal (MMM) junctions is of great importance for the advancement of molecular electronics. Critical factors that determine conductivity in a MMM junction include the nature of metal-molecule contacts and the electronic structure of the molecular backbone. We have studied the electronic transport property and the valence electronic structure on rigid, conjugated oligoacenes of increasing length with either thiol (-S) or isocyanide (-CN) linkers using conducting probe atomic force microscopy (CP-AFM) and ultraviolet photoelectron spectroscopy (UPS). We find that for these conjugated systems the Au-CN contact is more resistive than Au-S. The difference in contact resistance correlates with UPS measurements that show the highest-occupied molecular orbital (HOMO) of the isocyanide series is lower in energy (relative to the Fermi level of Au) than the HOMO of the thiol series, indicating the presence of a higher tunneling barrier at the contact for the isocyanide-linked molecules. By contrast, the difference in the HOMO positions for the two series of molecules does not appear to affect the length dependence of the junction resistance (i.e., the beta value = 0.5 A-1).     

Conductance titration of single-peptide molecules

We have measured the conductance of single peptides covalently bonded to two Au electrodes via S-Au bonds by repeatedly forming a large number of molecular junctions. The conductance decreases exponentially with the peptide length, with a decay constant of beta = 0.9 +/- 0.1 A-1, suggesting that tunneling is the mechanism of electron transport in the peptides. The conductance of the peptides is sensitive to the solution pH, due to the protonation/deprotonation of the amine and carboxyl groups of the peptides, which provides titration measurements based on single-molecule conductance.     

Electron exchange involving a sulfur-stabilized ruthenium radical cation

Half-sandwich Ru(II) amine, thiol, and thiolate complexes were prepared and characterized by X-ray crystallography. The thiol and amine complexes react slowly with acetonitrile to give free thiol or amine and the acetonitrile complex. With the thiol complex, the reaction is dissociative. The thiolate complex has been oxidized to its Ru(III) radical cation and the solution EPR spectrum of that radical cation recorded. Cobaltocene reduces the thiol complex to the thiolate complex. The 1H and 31P NMR signals of the thiolate complex in acetonitrile become very broad whenever the thiolate and thiol complexes are present simultaneously. The line broadening is primarily due to electron exchange between the thiolate complex and its radical cation; the latter is generated by an unfavorable redox equilibrium between the thiol and thiolate complexes. Pyramidal inversion of sulfur in the thiol complex is fast at room temperature but slow at lower temperatures; major and minor conformers of the thiol complex were observed by 31P NMR at -98 degrees C in CD2Cl2.     

Self-assembled monolayers on electrode surfaces: a probe for redox kinetics

The formation and characterization of self-assembled monolayers of organosulfur compounds like alkanethiols and dialkyl (di)sulfides on metal surfaces such as gold are areas of current research interest. The presence of an aromatic ring in a thiol molecule can enhance the binding between Au and the thiol, resulting in the formation of compact and impervious self-assembled monolayers. The formation of a monolayer of 2-mercaptobenzothiazole (MBT), containing an aromatic group with a fused thiazole ring but no long alkyl chain, is achieved on a gold electrode surface. Voltammetric investigations of ferro/ferricyanide and ferrous/ferric redox systems carried out on this Au|MBT electrode are reported. Further, the possibility of using such an Au|MBT electrode to distinguish between inner and outer sphere electron transfer reactions is indicated. Received: 2 January 1998 / Accepted: 14 May 1998     

Effect of composition on the conductivity and morphology of poly(3-hexylthiophene)/gold nanoparticle composite Langmuir-Schaeffer films

Ultrathin Langmuir-Schaeffer (LS) films were fabricated from blends of regioregular poly(3-hexylthiophene) (P3HT) and highly monodispersed dodecanethiolate-capped gold nanoparticles (Au NPs) mixed in varying weight ratios. The morphology of the ultrathin films was investigated by UV-visible absorption spectroscopy, atomic force microscopy (AFM) and field-emission scanning electron microscopy (FE-SEM). The results of the structural investigations were correlated with the lateral conductivity of the films, with P3HT in its unintentionally doped state, probed by scanning electrochemical microscopy (SECM), which proved to be a very sensitive technique. Control over the P3HT/Au NP ratio led to remarkable changes in the morphology and lateral conductivity of the films. Inclusion of Au NPs into P3HT was found to influence the ordering of P3HT, which ultimately determined the macroscopic charge transport characteristics of the films. Composite films with ca. 33% by weight of Au NPs were found to be the most ordered and exhibited the highest conductivity, substantially higher than P3HT alone. To provide insight into the film formation process, LS composite films comprising equal quantities of P3HT and Au NPs (by weight) were transferred at several surface pressures and investigated by SECM, AFM and FE-SEM.     

Self-assembled monolayers (SAMs) of alkoxycyanobiphenyl thiols on gold--a study of electron transfer reaction using cyclic voltammetry and electrochemical impedance spectroscopy

Self-assembled monolayers (SAMs) of liquid crystalline thiol-terminated alkoxycyanobiphenyl molecules with different alkyl chain lengths on Au surface have been studied for the first time using electrochemical techniques such as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The barrier property of the SAM-modified surfaces was evaluated using two different redox probes, namely potassium ferro/ferri cyanide and hexaammineruthenium(III) chloride. It was found that for short-length alkyl chain thiol (C5) the electron transfer reaction of hexaammineruthenium(III) chloride takes place through tunneling mechanism. In contrast, redox reaction of potassium ferro/ferri cyanide is almost completely blocked by the SAM-modified Au surface. From the impedance data, a surface coverage value of >99.9% was calculated for all the thiol molecules.     

AFM and STM characterization of thiol and thiophene functionalized SWNTs: pitfalls in the use of chemical markers to determine the extent of sidewall functionalization in SWNTs

Thiol- and thiophene-functionalized SWNTs prepared via the reaction of a substituted amine with fluoronanotubes show similar levels of sidewall functionalization, however, the use of Au nanoparticles as chemical markers for AFM gives misleading results for substituent distribution since STM shows the thiol substituents grouped in bands while the thiophene substituents uniformly distributed along the SWNTs.     

Selective ordering of surfactant modified gold nanoparticles in a diblock copolymer

Ordered aggregation of thiol-passivated Au nanoparticles in a diblock copolymer polystyrene-b-poly(methyl methacrylate) has been observed. The morphology of the diblock copolymer/Au-nanocomposite was dependent on the composition of the thiol modifier. For the thiol modifier that does not preferentially interact with one of the blocks, a perpendicular (relative to the substrate) lamellar morphology is maintained. However, for a thiol with a surfactant structure similar to one of the blocks, we observed a parallel lamellar morphology and speculate that the nanoparticles have localized at the microdomain interface. These conclusions are based on transmission electron microscopy, angle-dependent X-ray photoelectron microscopy and tensiometry. These results are consistent with theoretical predictions on the hybrid systems composed of block copolymers and nanoparticles.     

Enhanced hopping conductivity in low band gap donor-acceptor molecular wires Up to 20 nm in length

We have measured the current-voltage characteristics of conjugated oligo-tetrathiafulvalene-pyromelliticdiimide-imine (OTPI) wires ranging in length from 2.5 to 20.2 nm, contacted by Au electrodes. OTPI wires were built from Au substrates using alternating donor (tetrathiafulvalene, TTF) and acceptor (pyromelliticdiimide, PMDI) building blocks linked via aryl imine groups. Metal-molecule-metal junctions consisting of approximately 100 wires in parallel were prepared by contacting the wire films with an Au-coated atomic force microscope tip. The long OTPI wires exhibit a narrow band gap (<1.5 eV) and multiple redox states, which facilitate carrier injection from the Au contacts for hopping transport. We observe the theoretically predicted change in direct current (DC) transport from tunneling to hopping as a function of systematically controlled wire length, as well as strongly enhanced wire conductivity (0.02 S/cm) in the hopping regime. Hopping conduction is confirmed by length-, temperature-, and field-dependent transport measurements. These nanoscale transport measurements illuminate the role of molecular length and bond architecture on molecular conductivity and open opportunities for greater understanding of hopping transport in conjugated polymer films.     

Electron transport dynamics in a room-temperature Au nanoparticle molten salt

A room-temperature Au38 nanoparticle polyether melt has been prepared by exchanging poly(ethylene glycol) (PEG) thiolate ligands, HS-C6-PEG163, into the organic protecting monolayer of Au38(PhC2)24 nanoparticles. Spectral and electrochemical properties verify that the Au38 core size is preserved during the exchange. Adding LiClO4 electrolyte, free PEG plasticizer, and/or partitioned CO2 leads to an ionically conductive nanoparticle melt, on which voltammetric, chronoamperometric, and impedance measurements have been made, respectively, of the rates of electron and ion transport in the melt. Electron transport occurs by electron self-exchange reactions, or electron hopping, between diffusively relatively immobile Au38(0) and Au38(1+) nanoparticles. The rates of physical diffusion of electrolyte ions (diffusion coefficients DCION) are obtained from ionic conductivities. The measured rates of electron and of electrolyte ion transport are very similar, as are their thermal activation energy barriers, observations that are consistent with a recently introduced ion atmosphere relaxation model describing control of electron transfer in semisolid ion and electron-conductive media. The model has been previously demonstrated using a variety of metal complex polyether melts; the present results extend it to electron transfers between Au nanoparticles. In ion atmosphere relaxation control, measured rates and energy barriers for electron transfer are not intrinsic values but are instead characteristic of competition between back-electron transfer caused by a Coulombic disequilibrium resulting from an electron transfer and relaxation of counterions around donor-acceptor reaction partners so as to reachieve local electroneutrality.     

Silver Makes Better Electrical Contacts to Thiol‐Terminated Silanes than Gold

We report that the single‐molecule junction conductance of thiol‐terminated silanes with Ag electrodes are higher than the conductance of those formed with Au electrodes. These results are in contrast to the trends in the metal work function Φ(Ag)<Φ(Au). As such, a better alignment of the Au Fermi level to the molecular orbital of silane that mediates charge transport would be expected. This conductance trend is reversed when we replace the thiols with amines, highlighting the impact of metal–S covalent and metal–NH₂ dative bonds in controlling the molecular conductance. Density functional theory calculations elucidate the crucial role of the chemical linkers in determining the level alignment when molecules are attached to different metal contacts. We also demonstrate that conductance of thiol‐terminated silanes with Pt electrodes is lower than the ones formed with Au and Ag electrodes, again in contrast to the trends in the metal work‐functions.     

Expeditious synthesis of water-soluble, monolayer-protected gold nanoparticles of controlled size and monolayer composition

A protocol is reported for the preparation of water-soluble, thiol-protected Au nanoparticles (Au-MPC) where dioctylamine is used as a stabilizing agent when the gold cluster is formed using the two-phase Brust and Schiffrin procedure. The amount of amine controls the size of the nanoparticles in the 1.9-8.9 nm diameter range. The final stabilization of the gold clusters by addition of functionalized thiols is performed under very mild conditions compatible with most biomolecules. The procedure is suitable for a wide variety of functional groups present in the thiol and allows one to use thiol mixtures with a precise control of their composition in the monolayer. As a proof of principle, examples of nanoparticles protected with thiols comprising functional groups ranging from polyethers, saccharides, polyamines and ammonium ions are reported.     

Ultrathin Au nanowires and their transport properties

This paper presents a facile synthesis of single-crystalline Au nanowires by reduction of HAuCl4 in oleic acid and oleylamine. The diameter of these micron-meter-long Au nanowires is controlled to be 3 and 9 nm by volume ratio of oleylamine and oleic acid. When linked between two gold electrodes, the 9 nm Au nanowire shows good electron conductivity with its breakdown current density reaching 3.5 x 10(12) A/m2. This demonstrates that the chemically made ultrathin Au nanowires can be used as a molecular-scale interconnect for nanoelectronic applications.     

Au纳米粒子在有机溶剂中的电导行为

采用化学方法制备出粒径约10nm的Au纳米粒子,分别用十二、十四和十六烷基硫醇对Au粒子表面进行修饰,再溶入不同有机溶剂中,制备得到Au纳米粒子/氯仿和Au纳米粒子/甲苯溶液.测试了不同溶液的电导率随溶质浓度的变化规律,发现在整个浓度范围内存在一个临界浓度值.当溶质浓度低于临界浓度值时,溶液的电导率随溶质浓度的增加而迅速增加;而当溶质浓度超过临界浓度值时,溶液电导率的增加缓慢.在本文测试的浓度范围内,当Au纳米粒子分别被十二、十四和十六烷基硫醇修饰时,Au纳米粒子/氯仿溶液的临界浓度值分别约为11.22,7.96和5.47g/L.在相同浓度下,Au纳米粒子外面包裹的烷基硫醇的链长越短,其溶液的电导率越大.在整个浓度范围内,Au纳米粒子/氯仿溶液的电导率均高于Au纳米粒子/甲苯溶液的电导率.     

Size-selective synthesis of gold and platinum nanoparticles using novel thiol-functionalized ionic liquids

One-phase synthesis of gold and platinum nanoparticles using new thiol-functionalized ionic liquids (TFILs) is described for the first time. TFILs as stabilizing agents for gold and platinum nanoparticles were designed to have thiol groups on either the cation or anion and symmetrical or unsymmetrical positions only in the cation. Transmission electron microscopy, electron diffraction, and NMR were used for the characterization of nanoparticles. The metal nanoparticles formed using TFILs are crystalline structures with face-centered cubic packing arrangements and have small sizes (the average diameters are 3.5, 3.1, and 2.0 nm for Au and 3.2, 2.2, and 2.0 nm for Pt, respectively) and uniform distributions (the standard deviations are 0.7, 0.5, and 0.1 nm for Au and 1.1, 0.2, and 0.1 for Pt, respectively). It is believed that the nanoparticle size and distribution depend on the number and position of thiol groups in the IL.     

Charge Transport between Coupling Colloidal Perovskite Quantum Dots Assisted by Functional Conjugated Ligands

Long alkyl‐chain capping ligands are indispensable for preparing stable colloidal quantum dots. However, its insulating feature blocks efficient carrier transport among QDs, leading to inferior performance in light‐emitting diodes (LEDs). The trade‐off between conductivity and colloidal stability of QDs has now been overcome. Methylamine lead bromide (MAPbBr₃) QDs with a conjugated alkyl‐amine, 3‐phenyl‐2‐propen‐1‐amine (PPA), as ligands were prepared. Owing to electron cloud overlapping and the delocalization effect of conjugated molecules, the conductivity and carrier mobility of PPA‐QDs films increased almost 22 times over that of OA‐QD films without compromising colloidal stability and photoluminescence. PPA‐QDs LEDs exhibit a maximum current efficiency of 9.08 cd A^?1, which is 8 times of that of OA‐QDs LEDs (1.14 cd A^?1). This work provides critical solution for the poor conductivity of QDs in applications of energy‐related devices.     

Electron transport across the alkanethiol self-assembled monolayer/Au(111) interface: role of the chemical anchor

Alkanethiol self-assembled monolayers (SAMs) on Au(111) are model systems for molecular electronics. We probe the role of the chemisorption bond on electron dynamics at the SAM/Au interface using time-resolved two-photon photoemission. Formation of the Au-S bond is evidenced by a localized sigma resonance, which broadens and shifts upward in energy when the lying-down chemisorbed molecules stand up. The localized chemisorption bond does not affect the electronic coupling between delocalized image resonances and the metal substrate. Instead, lifetimes of image resonances are decreased due to scattering with S atoms within the thiol or thiolate monolayer.     

4-十二烷氧基苄胺在纳米金微粒合成中的应用

以新型表面活性剂4-十二烷氧基苄胺(C12OBA)构成的C12OBA/正丁醇/正庚烷/丙醛/HAuCl4(aq)反相微乳液作为微反应器,利用微波辐射加热-丙醛还原法制备了C12OBA包覆金纳米微粒;利用透射电镜、傅立叶变换红外光谱仪及X射线衍射仪分析了产物的微观形貌、化学键合特征、晶体结构;并测定了其紫外-可见吸收光谱.结果显示,表面活性剂C12OBA既可参与形成稳定的反相微乳液,又可作为金纳米微粒的良好保护剂.反相微乳液液滴的微小水核以及C12OBA/金的物质的量之比对纳米金微粒的尺寸和形貌起到良好的控制作用.