巯基棉分离-电感耦合等离子体质谱法测定铅铋共晶合金中痕量碲

建立了巯基棉(TCF)分离与电感耦合等离子体质谱ICP-MS结合测定LBE中痕量碲(Te)的分析方法,解决了ICP-MS无法直接测定铅铋共晶合金(LBE)中小于1μg/g痕量Te元素的问题。利用TCF的选择吸附性使溶液中Te与Pb,Bi分离,溶液中Pb,Bi的含量降至0.01 mg/L以下,而Te的损失率小于1%,成功消除了溶液中大量Pb,Bi产生的基体效应。优化了TCF的用量、滤液的流速、洗脱等条件。在优化的分析条件下,信号强度与Te标准工作溶液质量浓度在0.01～100μg/L范围内呈良好的线性关系,线性相关系数R2为0.9999,方法的检出限和定量限为0.04,0.15 ng/g,加标回收率95.5%～106.1%,精密度为1.1%～1.9%。方法可用于LBE样品中痕量Te的分析研究。     

电沉积Bi2Te3基薄膜的电化学阻抗谱研究

以不锈钢为基底,利用电化学沉积方法制备Bi2Te3基薄膜材料,并采用X射线衍射技术、电子探针微观分析等方法对薄膜进行结构和成分表征,通过电化学阻抗谱技术对不锈钢表面Bi2Te3的电化学沉积机理进行了初步探讨.结果表明Bi-Te和Bi-Te-Se体系具有相似的电化学沉积机理,即Bi3+和2HTeO+或H2SeO3首先被还原为Bi单质和Te或Se单质,然后Bi单质与Te或Se单质反应生成Bi2Te3基化合物,而Bi-Sb-Te体系中,2HTeO+首先被还原为Te单质,生成的Te再与Bi3+和Sb(III)反应生成Bi2Te3基化合物,三种体系的沉积都受电化学极化控制.     

n型Bi_2Te_(3-y)Se_y温差电材料薄膜的电化学制备及表征

采用电化学控电位的方法在不锈钢基片上电沉积制备了Bi2Te3-ySey温差电材料薄膜。研究了电沉积溶液中硒含量与薄膜中硒含量的关系,考察了不同沉积电位对电沉积Bi2Te3-ySey薄膜的温差电性能的影响,并采用ESEM、EDS、XRD等方法对电沉积薄膜的形貌、成分及结构进行了分析。结果表明,在含有Bi3 、HTeO2 和Se4 的电沉积溶液中,采用电化学沉积的方法,可实现铋、碲、硒三元共沉积,生成Bi2Te3-ySey半导体化合物。改变电沉积溶液组成,可控制Bi2Te3-ySey化合物中硒的掺杂浓度。-0.04V沉积电位下制备的Bi2Te3-ySey薄膜较平整、致密,组成为Bi2Te2.7Se0.3。退火处理可提高电沉积Bi2Te3-ySey薄膜的塞贝克系数,且控制沉积电位为-0.04V下制备的Bi2Te3-ySey薄膜退火后的塞贝克系数为-123μV·K-1。     

化学蒸气发生-四通道原子荧光光谱法同时测定高纯金中的痕量As,Sb,Bi,Te

采用化学蒸气发生-四通道原子荧光光谱法测定了高纯金中的痕量砷、锑、铋和碲。用乙酸乙脂萃取分离金,水相还原后采用化学蒸气发生-四通道原子荧光光谱法测定高纯金中的痕量砷、锑、铋和碲。在最佳条件下,方法对As,Sb,Bi,Te的检出限分别为0.04,0.05,0.04,0.03 ng/mL(3σ);测定精密度分别为0.98,0.89,0.94,0.99%(对10 ng/mL As,Sb,Bi和Te混合标准,n=7)。方法对实际样品中的As,Sb,Bi,Te进行了同时测定,测定结果与标准方法无明显差异,各元素的加标回收率为95%～105%。     

原位溶解-沉积法制备高可见光活性BiOI/Bi2O3光催化剂

以Bi2O3为前驱体,通过原位溶解-沉积法在KI溶液中制备了BiOI/Bi2O3光催化剂。用X射线衍射(XRD)、扫描电子显微镜(SEM)和紫外-可见漫反射光谱(UV-Vis DRS)等对样品进行了表征。结果表明Bi2O3球形颗粒紧密地贴在BiOI片上。随着KI溶液pH值的降低,Bi2O3逐渐转变为BiOI,且样品的吸收带边逐渐红移。在可见光(λ≥420 nm)下降解甲基橙,在pH=3下制备的BiOI/Bi2O3的活性最强,其原因是BiOI/Bi2O3 p-n异质结促进了光生载流子的分离。     

Carius管密封溶样-等离子体质谱法测定环境样品中镓、锗、砷、硒、镉、锡、锑、碲、汞、铅和铋

利用Carius管密封溶样技术,建立了王水分解-等离子体质谱直接测定环境样品中Ga,Ge,As,Se,Cd,Sn,Sb,Te,Hg,Pb和Bi的分析方法。在190℃下加热分解样品,稀释后可直接进行元素的分析测定。仪器测量时,乙醇不仅对As,Se和Te的检测信号有较明显的增敏作用,而且对复合离子ArCl+的形成还有一定的抑制作用。实验发现,3%乙醇增敏效果最好,分析信号强度可提高2～4倍。基于样品流程空白,所得方法检出限(3σ,DF=1000)为0.001μg/g(Cd)～0.281μg/g(Pb)。本方法应用于一系列土壤和水系沉积物国家标准物质,所得分析结果与推荐值相吻合,方法精度(RSD,n=3)优于5%。     

修饰铂电极上Bi(Ш)的示波双电位滴定法

制备了Bi(Ⅲ)修饰铂电极,用循环伏安法表征了Bi(Ⅲ)在电极上的吸附特性,探讨了电极的响应机理。 通过优化实验条件,建立了一种测定Bi(Ⅲ)的示波双电位滴定法。 在0.1 mol/L的硝酸溶液中(pH=1.0),用制备的修饰铂电极作为双指示电极,以EDTA标准溶液滴定Bi(Ⅲ),利用示波器屏幕上荧光点的显著最大位移指示滴定终点。 Bi(Ⅲ)在1.19×10-4～1.44×10-2 mol/L时,回收率为99.8%～100.1%,检出限(S/N=3)为1.0×10-4 mol/L。 该修饰电极具有良好的稳定性和重现性,在含有1.0×10-2 mol/L Bi(Ⅲ)的溶液中,连续7次测定,所得终点电位值均在100 mV左右,其相对标准偏差(RSD)为0.04%。 应用该方法测定含铋样品,RSD值(n=7)小于0.25%,回收率为99.5%～100.5%,测定结果与指示剂法测定值相符。     

Bi(Ⅲ)-茜素红-CTMAB体系共振散射光谱法测定环境水样中痕量铋

在pH=4.1的HCl溶液中,Bi(Ⅲ)与茜素红和十六烷基三甲基溴化铵（CTMAB）缔合形成粒径较大的疏水性三元离子缔合物（结合比为n(Bi(Ⅲ))∶n(AR)∶n(CTMAB)=1∶3∶3）,该反应导致共振光散射显著增强,最大散射峰位于364 nm。 研究了反应介质、pH值、共振探针浓度等对散射体系的影响,考察了该散射反应的稳定性及共存物质的影响,并对该三元离子缔合物的反应机理进行了探讨。 在2.5 mL 1.0×10-4 mol/L茜素红和2.0 mL 1.0×10-4 mol/L CTMAB最优试验条件下,Bi(Ⅲ)质量浓度与共振光散射强度ΔI364 nm在0～0.384 mg/L范围内呈良好线性关系,检测限为5.898×10-8 g/L,对含量为0.18 mg/L Bi(Ⅲ)溶液进行11次平行测定,其相对标准偏差为2.2%。 将该方法用于环境水样中痕量铋(质量浓度为0.552～0.831 μg/L)的测定,加标回收率为99.5%～100.2%,测定偏差小于2.7%。 基于Bi(Ⅲ)-AR-CTMAB三元离子缔合物的共振光散射光谱,建立了以茜素红染料为光谱探针的痕量Bi(Ⅲ)共振光散射检测新方法。     

EDTA辅助水热法合成硫化铋晶体

以Bi(NO3)3·5H2O和Na2S2O3·5H2O为原料,用乙二胺四乙酸(EDTA)辅助水热法合成了纳米或微米级的Bi2S3晶体(1),其结构、形貌和光谱性能经XRD,FE-SEM和UV-Vis表征。结果表明:溶液的pH对1的形貌有显著的影响,随着pH的增大,1由纳米棒组成的微米球逐渐转变为微米级片状结构;1出现蓝移。     

Bi(Ⅲ)-茜素红-十六烷基三甲基溴化铵体系共振散射光谱法测定环境水样中痕量铋

在pH=4.1的HCl溶液中,Bi(Ⅲ)与茜素红和十六烷基三甲基溴化铵(CTMAB)缔合形成粒径较大的疏水性三元离子缔合物(结合比为n(Bi(Ⅲ))∶n(AR)∶n(CTMAB)=1∶3∶3),该反应导致共振光散射显著增强,最大散射峰位于364nm。研究了反应介质、pH值、共振探针浓度等对散射体系的影响,考察了该散射反应的稳定性及共存物质的影响,并对该三元离子缔合物的反应机理进行了探讨。在2.5mL1.0×10-4mol/L茜素红和2.0mL1.0×10-4mol/LCTMAB最优试验条件下,Bi(Ⅲ)质量浓度与共振光散射强度ΔI364nm在0～0.384mg/L范围内呈良好线性关系,检测限为5.898×10-8g/L,对含量为0.18mg/LBi(Ⅲ)溶液进行11次平行测定,其相对标准偏差为2.2%。将该方法用于环境水样中痕量铋(质量浓度为0.552～0.831μg/L)的测定,加标回收率为99.5%～100.2%,测定偏差小于2.7%。基于Bi(Ⅲ)-AR-CTMAB三元离子缔合物的共振光散射光谱,建立了以茜素红染料为光谱探针的痕量Bi(Ⅲ)共振光散射检测新方法。     

Bismuth telluride (Bi2Te3) nanowires: synthesis by cyclic electrodeposition/stripping, thinning by electrooxidation, and electrical power generation

Nanowires composed of the thermoelectric material Bi2Te3 were synthesized on highly oriented pyrolytic graphite (HOPG) electrodes using the electrochemical step edge decoration (ESED) method. Nanowire synthesis was initiated by applying a voltage pulse of -0.75 V versus SCE for 5 ms to an HOPG electrode in an aqueous solution containing both Bi3+ and TeO22-, thereby producing nuclei at the step edges. Bi2Te3 was electrodeposited onto these nuclei using a cyclic electrodeposition-stripping scheme that involved the electrodeposition of bismuth-rich Bi2Te3 on a negative-going voltammetric scan (to -0.05 V) and the subsequent anodic stripping of excess bismuth from these nanowires during a positive-going scan (to +0.35 V). When this cycle was repeated 10-50 times, Bi2Te3 nanowires in the 100-300-nm-diameter range were obtained. These nanowires were narrowly dispersed in diameter (RSDdia = 10-20%), were more than 100 microm in length, and were organized into parallel arrays containing hundreds of wires. Smaller nanowires, with diameters down to 30 nm, were obtained by electrooxidizing 150-nm-diameter Bi2Te3 nanowires at +0.37 V under conditions of kinetic control. This oxidation process unexpectedly improved the uniformity of Bi2Te3 nanowires, and X-ray photoelectron spectroscopy (XPS) shows that these nanowires retain a Bi2Te3 core but also have a thin surface layer composed of Bi and Te oxides. The ability of Bi2Te3 nanowires to generate electrical power was assessed by transferring ensembles of these nanowires onto cyanoacrylate-coated glass surfaces and evaporating 4-point nickel contacts. A dimensionless figure of merit, ZT, ranging from 0 to 0.85 was measured for fresh samples that were less than 1 day old. XPS reveals that Bi2Te3 nanowires are oxidized within a week to Bi2O3 and TeO2. These oxides may interfere with the application by evaporation of electrical contacts to these nanowires.     

Determination of Lanthanide (III) Ions by Using a Flotation - Spectrophotometric Method

Abstract

This paper reports our attempt at determining Ln (III) ions by using a flotation-spectrophotometric method and our findings. When a ternary ion-association complex of Ln (III) coordinated by thiocyanate (SCN^?) and diantipyryl methane (DA[Mdot]) is separated by a mixed solvent containing benzene and chloroform at pH 3.1 – 4.2, a third phase is observed between the aqueous and organic phases. The solid ternary complex can be dissolved in acetone that contains thenoyltrifluoroacetone (TTA). The individual Ln (III) ion can be determined by using the 4th derivative spectra directly. The equilibrium constant of the ternary composition ratio of Ln(II1) to ligand is estimated by the equilibrium shift method. The mole ratio of Ln(II1) to DAM and to SCN^? is 1:3 each. The composition of the tcrnary complex seems to be Ln(III):DAM:SCN^?=1:3:3.     

Solvent Extraction Separation of Germanium(IV) with N-<Emphasis Type="Italic">n</Emphasis>-Octylaniline As an Extractant

The extraction behavior of germanium(IV) from aqueous hydrochloric acid solution with N-n-octylaniline in xylene was investigated. Hydrochloric acid concentration higher than 9 M remained effective for quantitative extraction of germanium(IV). Phenylfluorone ion as a counter anion was used. More than 2% N-n-octylaniline provided quantitative extraction at 1 min equilibrium time and germanium(IV) was back extracted by 7 M ammonia. The method was free from the interference of a large number of metal ions and anions, except for Te(IV) and Sn(IV); this was avoided using the masking effect. Germanium(IV) was separated from associated elements in its binary mixture with Si(IV), Te(IV), Sb(III), Bi(III), Au(III), Cu(II), Zn(II), and its ternary mixture with Se(IV), Te(IV); Sb(III), Bi(III); and Au(III), Cu(II). The proposed method was applied to a synthetic sample containing associated metal ions. The results indicated that trace amounts of germanium(IV) could be separated effectively from higher amounts of other elements.__________From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 5, 2005, pp. 463–467.Original English Text Copyright © 2005 by Sargar, Anuse.This article was submitted by the authors in English.     

纳米TiO2微柱分离富集测定环境样品中的微量碲

以处理过的纳米TiO2为微柱吸附材料,采用流动注射技术进行微量碲的分离富集,探讨了溶液的pH值、试样流速、试样体积、洗脱液浓度和用量以及干扰离子等因素的影响。 实验结果表明,pH值在8～9.5范围内,纳米TiO2对Te(Ⅳ)具有良好的吸附性能,吸附率接近99%,动态饱和吸附容量为37.02 mg/g;选用2 mL 0.5 mol/L NaOH溶液可将吸附的Te(Ⅳ)完全洗脱,富集倍数为30。 本法的检出限(3σ)为0.013 mg/L,相对标准偏差为RSD=1.99%。 将本法应用于水样的分析,碲的回收率在98%~103%之间,结果令人满意。     

火焰原子吸收光谱法测定粗铜中痕量铋、锑

粗铜样品经硝酸溶解,所得样品溶液中的铜离子在过量氨水中生成可溶性铜氨络离子,而铋、锑则以氢氧化铁和氢氧化镧作载体共沉淀,实现了富集铋、锑并与铜分离。基于此提出了原子吸收光谱法同时测定粗铜中的微量铋、锑。对浓盐酸的用量,硝酸铁和硝酸镧的加入量等试验条件进行了优化。铋的质量浓度在10 mg.L-1以内、锑的质量浓度在5 mg.L-1以内分别与其吸光度呈线性关系,检出限(3s)分别为0.06,0.04 mg.L-1,相对标准偏差(n=10)均小于2.0%。     

NH4Cl和HCl溶液浸取电石渣制备多晶型CaCO3

以电石渣为原料,分别以NH4Cl溶液和HCl溶液为浸取剂提取电石渣中的钙,以NH4HCO3为碳化剂制备CaCO3。研究了两种浸取工艺对电石渣中Ca^2+离子提取率的影响,并对两种体系浸取得到的Ca^2+离子提取率、二次残渣量和滤液中的杂质情况,以及制得的CaCO3的产率和性状进行了比较。结果表明,在浸取时间为30 min,浸取剂浓度为2.5 mol·L^-1,pH为8的条件下,以NH4Cl溶液浸取电石渣,加入量按Cl^-/Ca^2+物质的量比为2.0,得到Ca^2+离子提取率为92.87%;以HCl溶液浸取电石渣,加入量按Cl-/Ca^2+物质的量比为2.2,得到Ca^2+离子提取率为98.65%。Ca^2+离子滤液中的主要杂质通过调节pH均可以得到有效控制。NH4Cl溶液浸取电石渣Ca^2+离子提取率略低,二次残渣量高(22.39%),制得CaCO3的产率为1.065 g·g^-1电石渣;HCl溶液浸取电石渣Ca^2+离子提取率高,二次残渣量小(8.87%),制得CaCO3的产率为1.203 g·g^-1电石渣。两种浸取液碳化后制得的CaCO3产品纯度都在99%以上,白度在92.2-97.1%之间,通过控制碳化条件均可制得方解石型、球霰石型和文石型三种晶型的CaCO3。     

CsPb3Bi3Te8 and CsPb4Bi3Te9: low-dimensional compounds and the homologous series CsPbmBi3Te5 + m

Two new thermoelectric materials of quaternary bismuth telluride CsPb3Bi3Te8 and CsPb4Bi3Te9 are reported, which are members of a homologous series featuring anionic slabs [PbmBi3Te5 + m]- (m = 1-4) of monotonically increasing thickness.     

SPECTROPHOTOMETRIC STUDY OF BIMETALLIC TERNARY COMPLEX OF LANTHANUM——COPPER WITH ALIZARIN FLUORINE BLUE

The bimetallic ternary complex formation in the aqueous solution of La and Cu with alizarin fluorine blue (AFB) was studied by spectrophotometry.The ternary complex LaCu3(AFB)3 has maximum light absorption at 550nm.The colour reaction selectivity is fairly good and the method can be applied to the direct photometric determination of copper in lanthanum or some pure metals.A new mathematical approach to the treatment of spectrophotometric data for differentiation between mononuclear and polynuclear in solution is presented.The improvable fixed logarithm method is for complexes of the type MmBn(m=n) or MmBn(m=n).We report that La(Ⅲ) combines with AFB at pH 4.5 to form a single complex,withm=n=2,La2(AFB)2.