Microfiltration membranes with pH dependent property prepared from poly(methacrylic acid) grafted polyethersulfone powder

Poly(methacrylic acid) (PMAA) grafted polyethersulfone (PES) powder was prepared by γ-ray irradiation-induced graft polymerization. The existing of the PMAA side chains in the grafted powder was proved by FT-IR spectroscopy. Then, pH dependent microfiltration (MF) membranes were cast from PES-g-PMAA powder with different degree of grafting (DG) under phase inversion method. The contact angle, mean pore size and swelling behavior of MF membranes were measured. The morphology was studied and the water filtration property was also tested. The results showed that the mean pore sizes and filtration properties of MF membranes cast from PES-g-PMAA powder varied with pH. In the most variant case, the flux of acid solution was about four times as that of basic solution for the MF membrane cast from PES-g-PMAA with DG of 20.0%.     

Electrochemical properties of PP membranes with plasma polymer coatings of acrylic acid

Commercial polypropylene (PP) membranes were modified by plasma polymerization coating of acrylic acid, in combination with oxygen flow or oxygen plasma etching. First, conditions for plasma polymerization coating were optimized in terms of the chemical resistance of the coatings and their ion exchange capacity as a function of plasma power, internal pressure and treatment time. Next, the plasma polymerization coating of acrylic acid was combined with oxygen flow or oxygen plasma etching, and their conditions were also optimized by measuring the ion exchange capacity. Finally, the modified membranes were subjected to electrical resistance and transport number measurements and characterized by -step, FT-IR/ATR and SEM. Among the modification methods, oxygen plasma etching followed by the plasma polymerization coating of acrylic acid provided the best electrochemical properties with 1.75 meq/g (IEC) and 112 Ω cm² (ER), 0.88 (TN).     

Radiation synthesis of chitosan beads grafted with acrylic acid for metal ions sorption

Radiation-induced grafting of acrylic acid onto chitosan beads was performed in solution at a dose rate of 20.6 Gy/min of cobalt-60 gamma rays. The effect of absorbed dose on grafting yield was investigated. The characterization of the grafted material was performed by FTIR spectroscopy and the swelling measurements at different pHs. The grafting yield increased with the increase in dose, it reached 80% at 40 kGy irradiation dose.The removal of Pb and Cd ions from aqueous solutions was investigated with both ungrafted and grafted chitosan beads. The sorption behavior of the sorbents was examined through pH, kinetics and equilibrium measurements. Grafted chitosan beads presented higher sorption capacity for both metal ions than unmodified chitosan beads.     

Preparation and characterization of a homobifunctional silicone rubber membrane grafted with acrylic acid via plasma-induced graft copolymerization

Polyacrylic acid (PAA) was grafted onto the surface of silicone rubber membrane (SR) by plasma-induced graft copolymerization (PIP). Ar-plasma was used to activate the surface of SR. Also, a determination was made of the influences of plasma treatment power, pressure, time, grafted copolymerization reaction time, and monomer concentration on polymerization yield. The surface properties of SR were measured by ATR-FTIR, ESCA, and SIMS. In those analyses, the elemental composition and different carbon bindings on the surface of SR were examined by ESCA with the amount of O1s/C1s being approximately 0.7 at 60 s by Ar-plasma treatment (60 W, 200 mtorr). The peroxide group introduced on SR was measured via 1,1-diphenyl-2-picryhydrazyl (DPPH). The optimum amount of peroxide groups was 6.85 × 10⁻⁸ mol/cm² at 60 s of Ar-plasma treatment. The peroxide group (33D peak) was introduced onto the surface of SR by negative spectra of SIMS analysis after SR treatment by Ar-plasma. An increase was obtained in grafted polymerization yield with a region of 5 to 50% (v/v) of acrylic acid aqueous solution. Both sites of polyacrylic acid were detected after staining by toluidine blue O. That is, a homobifunctional membrane was developed via this surface modification method. © 1996 John Wiley & Sons, Inc.     

A novel approach to prepare proton exchange membranes from fluoropolymer powder by pre-irradiation induced graft polymerization

A novel approach was developed to overcome the non-uniform distribution of grafted polystyrene (PS) chains across proton exchange membranes (PEMs) manufactured using radiation induced graft polymerization of commercialized fluoropolymer films. This process involves the three key steps of grafting of styrene into fluoropolymer powder, processing the grafted powder into membranes, and then obtaining the PEM by sulfonation of these membranes. The structure of the membranes and the PEMs were analyzed by means of infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscope with energy-dispersive X-ray analysis (SEM-EDX) to demonstrate the uniform distribution of poly(styrene-sulfonic acid) (denoted as PSSA) graft-chains across the PEM. The properties of the resulting PEMs, such as their ion exchange capacity (IEC), water uptake (WU), proton conductivity, dimensional stability, oxidative stability and thermal stability, were also investigated.     

Proton conducting grafted/crosslinked membranes prepared from poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) copolymer

Poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) (P(VDF‐co‐CTFE)) backbone was grafted with crosslinkable chains of poly(hydroxyl ethyl acrylate) (PHEA) and proton conducting chains of poly(styrene sulfonic acid) (PSSA) to produce amphiphilic P(VDF‐co‐CTFE)‐g‐P(HEA‐co‐SSA) graft copolymer via atom transfer radical polymerization (ATRP). Successful synthesis and microphase‐separated structure of the copolymer were confirmed by ¹H NMR, FT‐IR spectroscopy, and TEM analysis. Furthermore, this graft copolymer was thermally crosslinked with sulfosuccinic acid (SA) to produce grafted/crosslinked membranes. Ion exchange capacity (IEC) increased continuously with increasing SA contents but the water uptake increased up to 6 wt% of SA concentration, above which it decreased monotonically. The membrane also exhibited a maximum proton conductivity of 0.062 S/cm at 6 wt% of SA concentration, resulting from competitive effect between the increase of ionic groups and the degree of crosslinking. XRD patterns also revealed that the crystalline structures of P(VDF‐co‐CTFE) disrupted upon graft polymerization and crosslinking. These membranes exhibited good thermal stability at least up to 250°C, as revealed by TGA. Copyright © 2009 John Wiley & Sons, Ltd.     

Surface modification of non-woven fabric by DC pulsed plasma treatment and graft polymerization with acrylic acid

Direct-current pulsed plasma treatment (DPPT) followed by thermal-induced graft polymerization with acrylic acid (AA) was used to modify poly(ethylene terephthalate)/polyethylene (PET/PE) non-woven fabric (NWF) in this study. The water contact angle of plasma modified NWF decreased sharply with DPPT time in 4 s. The water content of the NWF increased with DPPT time and levelled off after 30 s. Chemical analysis by X-ray photoelectron spectroscopy (XPS) indicated that the surface property of modified NWF could be maintained for more than 8 months under ambient conditions and could be further improved by grafting with acrylic acid. The concentration of AA in PET/PE-g-AA NWF increased both with the monomer concentration and the plasma treatment time. The maximum grafting density was 1.17 μmol/cm² with 40 s DPPT and 20% (w/w) AA. Improved biocompatibility of the modified NWF was confirmed with 3T3 fibroblast cells where cell viability was analyzed by MTT assays. More cells were found to attach to the modified NWF with higher growth rates, indicating that an improvement in surface properties by DPPT followed by graft polymerization of AA is beneficial for cell attachment and growth. A much more uniform cell distribution was found within the modified NWF from confocal laser scanning microscope observations.     

Radiation grafting of pH and thermosensitive N-isopropylacrylamide and acrylic acid onto PTFE films by two-steps process

Polytetrafluoroethylene (PTFE) was grafted (g) with acrylic acid (AAc) by γ-ray pre-irradiation method to get PTFE-g-AAc films, then N-isopropylacrylamide (NIPAAm) was grafted onto PTFE-g-AAc films with γ-ray to get (PTFE-g-AAc)-g-NIPAAm. PTFE films were irradiated in air at a dose rate of 3.0 kGy h^–1 and different radiation dose. The irradiated films were placed in glass ampoules, which contained aqueous solutions with different monomer concentration (AAc), and then they were heated at different temperatures and reaction time. NIPAAm onto PTFE-g-AAc was carried out with the same procedure with monomer concentration of 1 mol L⁻¹. The thermosensitivity of the samples was defined and calculated as the ratio of the grafted samples swelling at 28 and 35 °C, and pH sensitivity defined as the ratio of the grafted samples swelling at pH 2 and 8.     

Modified chitosan 4. Superabsorbent hydrogels from poly(acrylic acid-co-acrylamide) grafted chitosan with salt- and pH-responsiveness properties

Graft copolymerization of mixtures of acrylic acid (AA) and acrylamide (AAm) onto chitosan was carried out by using potassium persulfate (KPS) as a free radical initiator in the presence of methylenebisacrylamide (MBA) as a crosslinker. The effect of reaction variables, such as MBA concentration and AA/AAm ratio on the water absorbency capacity have been investigated. The polymer structures were confirmed by FTIR spectroscopy. Water absorbencies were compared for the hydrogels before and after alkaline hydrolysis. In the non-hydrolyzed hydrogel, enhanced water absorbency was obtained with increasing AA in monomer feed. However, after saponification, the sample with high AAm ratio exhibited more water absorbency. These behaviors were discussed according to structural parameters. The swelling kinetics of the superabsorbing hydrogels was studied as well. The hydrogels exhibited ampholytic and reversible pH-responsiveness characteristics. The swelling variations were explained according to swelling theory based on the hydrogel chemical structure. The hydrogels exhibited salt-sensitivity and cation exchange properties. The pH-reversibility and on-off switching properties of the hydrogels make the intelligent polymers as good candidates for considering as potential carriers for bioactive agents, e.g. drugs.     

Structure and swelling-release behaviour of poly(vinyl pyrrolidone) (PVP) and acrylic acid (AAc) copolymer hydrogels prepared by gamma irradiation

Copolymer network hydrogels were prepared by gamma irradiation of aqueous solutions of poly(vinyl pyrrolidone) (PVP) and acrylic acid monomer (AAc). The composition of the final hydrogels compared to the composition of the initial preparation solutions of hydrogels was determined. The chemical structure and nature of bonding was characterized by IR spectroscopy analysis, while the thermal durability of the prepared hydrogels was assessed by thermogravimetric analysis (TGA). The kinetic swelling in water and the pH-sensitivity of PVP/AAc copolymer hydrogels was studied. The drug release properties of PVP/AAc hydrogels taking methyl orange indicator as a drug model was investigated. The IR spectra indicate the formation of copolymer networks, whereas the TGA study showed that the PVP/AAc hydrogels possess higher thermal stability than pure PAAc and lower than PVP hydrogels. The kinetic swelling in water showed that all the hydrogels reached equilibrium after 24 h and that the degree of swelling increases with increasing the ratio of AAc in the initial feeding solutions. It was found that the degree of swelling of PVP/AAc hydrogels increases greatly within the pH range 4-7 depending on composition.     

Radiation‐grafted solid polymer electrolyte membrane: studies of fluorinated ethylene propylene (FEP) copolymer‐g‐acrylic acid grafted membranes and their sulfonated derivatives

Acrylic acid was grafted onto FEP by simultaneous radiation technique and the resulting membranes were sulfonated. Results of dynamic mechanical properties of the membranes showed that storage modulus and temperature at tan δ_(max) increases on grafting. X‐ray diffraction (XRD) analysis of the grafted and sulfonated membranes showed decreasing trend in crystallinity with increase in degree of grafting. From scanning electron microscopy (SEM) studies it was confirmed that grafting takes place by the front mechanism. Copyright © 2004 John Wiley & Sons, Ltd.     

Association between benzalkonium chloride and a poly( acrylic acid) gel. Study by microfiltration and membrane dialysis

Interactions between benzalkonium chloride (BAK) and the respective polymers, and the related availability of BAK in the corresponding solution, were studied for aqueous preparations of hydroxyethylcellulose (HEC), polyvinyl alcohol (PVA) and crosslinked poly(acrylic acid) (PAA). The study was performed by means of a crossflow filtration process with an alumina membrane. In the presence of the PAA gel, the rejection rate of BAK is much higher than with HEC or PVA. These results can be explained by the association of the benzalkonium cation BAK⁺ with the negative carboxylate groups or the PAA. This effect, which was confirmed by dialysis experiments, leads to the trapping of BAK⁺ inside the polymer network and could be of interest in the reduction of the harmful effects of BAK observed in the treatment of eye diseases.     

Amphiphilic conetworks. IV. Poly(methacrylic acid)‐l‐polyisobutylene and poly(acrylic acid)‐l‐polyisobutylene based hydrogels prepared by two‐step polymer procedure. New pH responsive conetworks

This article describes the synthesis and characterization of new amphiphilic polymer conetworks containing hydrophilic poly(methacrylic acid) (PMAA) or poly(acrylic acid) (PAA) and hydrophobic polyisobutylene (PIB) chains. These conetworks were prepared by a two‐step polymer synthesis. In the first step, a cationic copolymer of isobutylene (IB) and 3‐isopropenyl‐α,α‐dimethylbenzyl isocyanate (IDI) was prepared. The isocyanate groups of the IB–IDI random copolymer were subsequently transformed in situ to methacrylate (MA) groups in reaction with 2‐hydroxyethyl methacrylate (HEMA). In the second step, the resulting MA‐multifunctional PIB‐based crosslinker, PIB(MA)_n, with an average functionality of approximately four methacrylic groups per chain, was copolymerized with methacrylic acid (MAA) or acrylic acid (AA) by radical mechanism in tetrahydrofuran giving rise to amphiphilic conetworks containing 31–79 mol % of MAA or 26–36 mol % of AA. The synthesized conetworks were characterized with solid‐state ¹³C‐NMR spectroscopy and differential scanning calorimetry. The amphiphilic nature of the conetworks was proven by swelling in both aqueous media with low and high pH and n‐heptane. The effect of varying pH on the swelling behavior of the synthesized conetworks is presented. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1284–1291, 2009     

Composite membranes prepared from glutaraldehyde cross-linked sulfonated cardo polyetherketone and its blends for the dehydration of acetic acid by pervaporation

Cardo polyetherketone (PEK-C) composite membranes were prepared by casting glutaraldehyde (GA) cross-linked sulfonated cardo polyetherketone (SPEK-C) or silicotungstic acid (STA) filled SPEK-C and poly(vinyl alcohol) (PVA) blending onto a PEK-C substrate. The compatibility between the active layer and PEK-C substrate is improved by immersing the PEK-C substrate in a GA cross-linked sodium alginate (NaAlg) solution and using water–dimethyl sulfoxide (DMSO) as a co-solvent for preparing the STA-PVA-SPEK-C/GA active layer. The pervaporation (PV) dehydration of acetic acid shows that permeation flux decreased and separation factor increased with increasing GA content in the homogeneous membranes. The permeation flux achieved a minimum and the separation factor a maximum when the GA content increased to a certain amount. Thereafter the permeation flux increased and the separation factor decreased with further increasing the GA content. The PV performance of the composite membranes is superior to that of the homogeneous membranes when the feed water content is below 25 wt%. The permeation activation energy of the composite membranes is lower than that of the homogeneous membranes in the PV dehydration of 10 wt% water in acetic acid. The STA-PVA-SPEK-C-GA/PEK-C composite membrane using water–DMSO as co-solvent has an excellent separation performance with a flux of 592 g m⁻² h⁻¹ and a separation factor of 91.2 at a feed water content of 10 wt% at 50 °C.     

Effect of annealing on the morphology and properties of poly(lactic acid)/polyhedral oligomeric silsesquioxane asymmetric porous membranes prepared through non-solvent induced phase separation and its application

Non-solvent induced phase separation (NIPS) method was employed to fabricate biodegradable poly(lactic acid) (PLA) nanocomposite membranes. Morphological studies using scanning electron microscopy revealed that all the membranes prepared display asymmetric structures comprising finger-like macropores. The incorporation of modified polyhedral oligomeric silsesquioxane (POSS) particles into the PLA matrix resulted in enhanced crystallinity, mechanical, and thermal properties. Annealing of the membranes was performed to explore the influence of temperature on the morphology and properties. After annealing, membranes become more thin and compact, and drastic enhancement in crystallinity is also observed. Consequently, Young's modulus experiences a significant improvement. The reduction in oil absorption capacity after annealing can be attributed to the higher level of crystallinity, reduced porosity, and smaller pore diameter observed in the annealed membranes. Additionally, the unannealed PLA nanocomposite membranes demonstrated exceptional oil absorption capacity, reaching approximately 88%. It is foreseeable that these PLA/POSS nanocomposite membranes possess the potential to be utilized as effective tools for oil–water separation, offering the advantage of mitigating secondary pollution.     

Microwave assisted hydroxyalkylamidation of poly(ethylene‐co‐acrylic acid) and formation of grafted poly(ϵ‐caprolactone) side chains

The microwave assisted amidation of poly(ethylene‐co‐acrylic acid) (PEAA) with 2‐(2‐aminoethoxy)ethanol was performed to yield a hydroxy functionalized poly(ethylene) based copolymer (PEAAOH) in a single step. PEAAOH was used as a polyinitiator for the ring‐opening polymerization of ε‐caprolactone. The obtained graft copolymers were studied via ¹H NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, polarized optical microscopy, and scanning electron microscopy. Microscopy methods show a crystallization behavior of banded spherulites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3659–3667, 2007     

New powder coatings with low curing temperature and enhanced mechanical properties obtained from DGEBA epoxy resins and Meldrum acid using erbium triflate as curing agent

New low curing temperature powder coatings obtained by copolymerization of epoxy resins with Meldrum acid (MA) initiated by erbium (III) trifluoromethanesulfonate have been formulated. Their mechanical and thermomechanical properties have been studied and compared with a commonly used industrial system (o-tolylbiguanide/epoxy resin) and with an already formulated epoxy powder coating homopolymerized by erbium trifluoromethanesulfonate. Systems containing low proportions of MA and initiated by erbium trifluoromethanesulfonate lead to a great reduction of curing conditions (temperature/time). Moreover, the new formulated systems present very good mechanical properties, adhesion, and impact resistance. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2316–2327, 2007     

Industrial recovery of mixed acid (HF + HNO3) from the titanium spent leaching solutions by diffusion dialysis with a new series of anion exchange membranes

The results of the development of the industrial diffusion dialysis technology and the unit based on it for mixed acid recovery from titanium metal processing have been considered. Mixed acid can be selectively separated from the spent liquor contained mainly HNO₃, HF and titanium ions by diffusion dialysis using a new series of anion exchange membranes. The results showed that this separation is seriously affected by the membrane water content and ion exchange capacity (IEC). Some titanium complex anion (TiF₆)²⁻ give rise to the difficulty in separation so that the best separation efficiency does not occur at the cases of high water content and IEC of membranes. By controlling the membrane preparation conditions (bromination content and position), a desired membrane for this system has been obtained with both relatively high acid recovery ratio and acid/titanium selectivity.

Economic estimation was conducted based on an industrial diffusion dialyser with 499 sheets of 1600 mm×800 mm membrane and the practical runs parameters: process quantity 2400 m³ per year, total acid recovery ratio 85%. The results showed that the investment could be recovered within 5 months. After 5 years’ run, one such dialyser can bring about CN$ 4.3 million profits besides the significant environmental benefits.     

Modification and characterization of semi-crystalline poly(vinyl alcohol) with interpenetrating poly(acrylic acid) by UV radiation method for alkaline solid polymer electrolytes membrane

Semi-crystalline poly(vinyl alcohol) was modified by UV radiation with acrylic acid monomer to get interpenetrating poly(acrylic acid) modified poly(vinyl alcohol), PVAAA, membrane. The stability of various PVAAA membranes in water, 2 M CH₃OH, 2 M H₂SO₄, and 40 wt% KOH aqueous media were evaluated. It was found that the stability of PVAAA membrane is stable in 40 wt% KOH solution. The PVAAA membranes were characterized by differential scanning calorimetry, X-ray diffraction, and thermogravimetry analysis. These results show that (1) the crystallinity in PVAAA decreased with increasing the content of poly(acrylic acid) in the PVAAA membranes. (2) The melting point of the PVAAA membrane is reduced with increasing the content of poly(acrylic acid) in the membrane. (3) Three stages of thermal degradation were found for pure PVA. Compared to pure PVA, the temperature of thermal degradation increased for the PVAAA membrane. The various PVAAA membranes were immersed in KOH solution to form polymer electrolyte membranes, PVAAA-KOH, and their performances for alkaline solid polymer electrolyte were conducted. At room temperature, the ionic conductivity increased from 0.044 to 0.312 S/cm. The result was due to the formation of interpenetrating polymer chain of poly(acrylic acid) in the PVAAA membrane and resulting in the increase of charge carriers in the PVA polymer matrix. Compared to the data reported for different membranes by other studies, our PVAAA membrane are highly ionic conducting alkaline solid polymer electrolytes membranes.