Surface bonding on silicon surfaces as probed by tip-enhanced Raman spectroscopy

Tip-enhanced Raman spectroscopy (TERS) has been used to obtain the Raman signal of surface species on silicon single crystal surfaces without the necessity for surface enhancement by addition of Ag nanoparticles. By illuminating the hydrogen terminated silicon surface covered with a droplet of 4-vinylpyridine with UV light, a 4-ethylpyridine modified silicon surface can be easily obtained. By bringing a scanning tunneling microscope (STM) Au tip with a nanoscale tip apex to a distance of ca. 1 nm from the m...     

In situ determination of the thermodynamic surface properties of chemically modified surfaces on a local scale: an attempt with the atomic force microscope

We have monitored deflection-distance curves with an atomic force microscope (AFM) in contact mode, with a silicon nitride tip, on chemically modified silicon wafers, in the air. The wafers were modified on their surface by grafting self-assembled monolayers (SAMs) of different functional groups such as methyl, ester, amine, or methyl fluoride. A chemically modified surface with a functionalized hydroxyl group was also considered. Qualitative analysis allowed us to compare adhesive forces versus chemical features and surface energy. The systematic calibration procedure of the AFM measurements was performed to produce quantitative data. Our results show that the experimentally determined adhesive force or thermodynamic work of adhesion increases linearly with the total surface energy determined with contact angles measured with different liquids. The influence of capillary condensation of atmospheric water vapor at the tip-sample interface on the measured forces is discussed. Quantitative assessment values were used to determine in situ the SAM-tip thermodynamic work of adhesion on a local scale, which have been found to be in good agreement with quoted values. Finally, the determination of the surface energy of the silicon wafer deduced from the thermodynamic work of adhesion is also proposed and compared with the theoretical value.     

AFM of adsorbed polyelectrolytes on cellulose I surfaces spin-coated on silicon wafers

Thin layers of cellulose I nanocrystals were spin-coated onto silicon wafers to give a flat model cellulose surface. A mild heat treatment was required to stabilize the cellulose layer. Interactions of this surface with polyelectrolyte layers and multilayers were probed by atomic force microscopy in water and dilute salt solutions. Deflection–distance curves for standard silicon nitride tips were measured for silicon, cellulose-coated silicon, and for polyelectrolytes adsorbed on the cellulose surface. Transfer of polymer to the tip was checked by running deflection–distance curves against clean silicon. Deflection–distance curves were relatively insensitive to adsorbed polyelectrolyte, but salt addition caused transfer of cationic polyelectrolyte to the tip, and swelling of the polyelectrolyte multilayers.     

Uniformly sized gold nanoparticles derived from PS-b-P2VP block copolymer templates for the controllable synthesis of Si nanowires

A monolayer of gold-containing surface micelles has been produced by spin-coating solution micelles formed by the self-assembly of the gold-modified polystyrene-b-poly(2-vinylpyridine) block copolymer in toluene. After oxygen plasma removed the block copolymer template, highly ordered and uniformly sized nanoparticles have been generated. Unlike other published methods that require reduction treatments to form gold nanoparticles in the zero-valent state, these as-synthesized nanoparticles are in form of metallic gold. These gold nanoparticles have been demonstrated to be an excellent catalyst system for growing small-diameter silicon nanowires. The uniformly sized gold nanoparticles have promoted the controllable synthesis of silicon nanowires with a narrow diameter distribution. Because of the ability to form a monolayer of surface micelles with a high degree of order, evenly distributed gold nanoparticles have been produced on a surface. As a result, uniformly distributed, high-density silicon nanowires have been generated. The process described herein is fully compatible with existing semiconductor processing techniques and can be readily integrated into device fabrication.     

Probing colloidal forces between a Si3N4 AFM tip and single nanoparticles of silica and alumina

The atomic force microscope (AFM) has been used to measure surface forces between silicon nitride AFM tips and individual nanoparticles deposited on substrates in 10(-4) and 10(-2) M KCl solutions. Silica nanoparticles (10 nm diameter) were deposited on an alumina substrate and alumina particles (5 to 80 nm diameter) were deposited on a mica substrate using aqueous suspensions. Ionic concentrations and pH were used to manage attractive substrate-particle electrostatic forces. The AFM tip was located on deposited nanoparticles using an operator controlled offset to achieve stepwise tip movements. Nanoparticles were found to have a negligible effect on long-range tip-substrate interactions, however, the forces between the tip and nanoparticle were detectable at small separations. Exponentially increasing short-range repulsive forces, attributed to the hydration forces, were observed for silica nanoparticles. The effective range of hydration forces was found to be 2-3 nm with the decay length of 0.8-1.3 nm. These parameters are in a good agreement with the results reported for macroscopic surfaces of silica obtained using the surface force apparatus suggesting that hydration forces for the silica nanoparticles are similar to those for flat silica surfaces. Hydration forces were not observed for either alumina substrates or alumina nanoparticles in both 10(-4) M KCl solution at pH 6.5 and 10(-2) M KCl at pH 10.2. Instead, strong attractive forces between the silicon nitride tip and the alumina (nanoparticles and substrate) were observed.     

Conversion of a metastable superhydrophobic surface to an ultraphobic surface

Superhydrophobic surfaces in Wenzel and metastable wetting state were prepared and the conversion of such surfaces to ultraphobic surfaces was reported by the application of a fine-scale roughness. Silicon nitride substrates with hexagonally arranged pillars were prepared by micromachining. The two-scale roughness was achieved by coating these substrates with 60 nm silica nanoparticles. The surface was made hydrophobic by silanization with octadecytrichlorosilane (OTS). Wettability studies of the silicon nitride flat surface, silicon nitride pillars, and the surfaces with two-scale roughness showed that a two-scale roughness can effectively improve the hydrophobicity of surfaces with a higher apparent contact angle and reduced contact angle hysteresis when the original rough surface was in a metastable or Wenzel state. This study shows the pathway of converting a metastable hydrophobic surface to an ultraphobic surface by the introduction of a fine-scale roughness, which adds to the literature a new aspect of fine-scale roughness effect.     

The effect of the degree of ionicity of ceramic materials on their wettability by melted sodium chloride

The sessile drop method has been used to study the wettability of hexagonal boron nitride, sapphire, quartz, and polycrystalline silicon carbide by melted sodium chloride in a reducing He–H₂ atmosphere. Melted NaCl completely spreads over sapphire and quartz surfaces and form finite contact angles equal to 51° ± 10° and 77° ± 5° on silicon carbide and hexagonal boron nitride, respectively. The calculated works of salt adhesion to the ceramic substrates increase with the magnitude of the ionic component of ceramic material surface energy.     

Alternative method for fabricating chemically functionalized AFM tips: silane modification of HF-treated Si3N4 probes

An alternative method for fabricating functionalized, atomic force microscopy (AFM) tips is presented. This technique is simple and requires only minimal preparation and tip modification to generate chemically sensitive probes that have a robust organic monolayer of flexible terminal chemistry attached to the surface. Specifically, commercially microfabricated Si3N4 AFM tips were modified with self-assembled monolayers (SAMs) of octadecyltrichlorosilane and (11-bromoundecyl)trichlorosilane after removing the native silicon oxide surface layer with concentrated hydrofluoric acid. The structure of these SAM films on solid silicon nitride surfaces was studied using contact angle goniometry and Fourier transform infrared spectroscopy. Pull-off force measurements on various bare (mica, graphite, and silicon) and SAM-functionalized substrates confirm that mechanically robust, long-chain organic silane SAMs can be formed on HF-treated Si3N4 tips without the presence of an intervening oxide layer. Adhesion experiments show that the integrity of the organic film on the chemically modified tips is maintained over repeated measurements and that the functionalized tips can be used for chemical sensing experiments since strong discrimination between different surface chemistries is possible.     

CALCULATION OF THE YOUNG''''S MODULUS OF AN ADSORBED POLYMER LAYER

Polymer layers adsorbed to a surface or in a confined environment often change their mechanical properties. There is even the possibility of solidification of the confined layer. To judge the stiffness of such a layer, we used the Hertz model to calculate the Young's modulus of the polymer layer in the confinement of AFM experiments with silicon nitride tip with a radius of curvature of R≈50 nm and a glass sphere attached to the cantilever R = 5μm. Since there is no visible indentation of the layer in the AFM experiments, the layer is either penetrated very easily, or the indentation is too small to be seen in a force curve. The latter would be the case for a polymer layer with a Young's modulus above 4×108 Pa in case of an experiment with a silicon nitride tip and 4×105 Pa in case of a glass sphere.     

Stress dependence of optically active diamagnetic point defects in silicon oxynitride

The cathodoluminescence (CL) spectrum arising from diamagnetic point defects of silicon oxynitride lattice was analyzed to extract quantitative information on local stress fields stored on the surface of a silicon nitride polycrystal. A calibration procedure was preliminarily made to obtain a relationship between CL spectral shift and applied stress, according to the piezo-spectroscopic effect. In this calibration procedure, we used the uniaxial stress field developed in a rectangular bar loaded in a four-point flexural jig. Stress dependence was clearly detected for the most intense spectral band of a doublet arising from diamagnetic ([triple bond]Si-Si[triple bond]) defects, which was located at around 340 nm. The shallow nature of the electron probe enabled the characterization of surface stress fields with sub-micrometer-order spatial resolution. As applications of the PS technique, the CL emission from [triple bond]Si-Si[triple bond] defects was used as a stress probe for visualizing the residual stress fields stored at grain-boundary regions and at the tip of a surface crack propagated in polycrystalline silicon nitride.     

Creating surfactant nanoparticles for block copolymer composites through surface chemistry

A simple strategy to tailor the surface of nanoparticles for their specific adsorption to and localization at block copolymer interfaces was explored. Gold nanoparticles coated by a mixture of low molecular weight thiol end-functional polystyrene (PS-SH) (Mn = 1.5 and 3.4 kg/mol) and poly(2-vinylpyridine) homopolymers (P2VP-SH) (Mn = 1.5 and 3.0 kg/mol) were incorporated into a lamellar poly(styrene-b-2-vinylpyridine) diblock copolymer (PS-b-P2VP) (Mn = 196 kg/mol). A library of nanoparticles with varying PS and P2VP surface compositions (FPS) and high polymer ligand areal chain densities was synthesized. The location of the nanoparticles in the PS-b-P2VP block copolymer was determined by transmission electron microscopy. Sharp transitions in particle location from the PS domain to the PS/P2VP interface, and subsequently to the P2VP domain, were observed at FPS = 0.9 and 0.1, respectively. This extremely wide window of FPS values where the polymer-coated gold nanoparticles adsorb to the interface suggests a redistribution of PS and P2VP polymers on the Au surface, inducing the formation of amphiphilic nanoparticles at the PS/P2VP interface. In a second and synthetically more challenging approach, gold nanoparticles were covered with a thiol terminated random copolymer of styrene and 2-vinylpyridine synthesized by RAFT polymerization. Two different random copolymers were considered, where the molecular weight was fixed at 3.5 kg/mol and the relative incorporation of styrene and 2-vinylpyridine repeat units varied (FPS = 0.52 and 0.40). The areal chain density of these random copolymers on Au is unfortunately not high enough to preclude any contact between the P2VP block of the block copolymer and the Au surface. Interestingly, gold nanoparticles coated by the random copolymer with FPS = 0.4 were dispersed in the P2VP domain, while those with FPS = 0.52 were located at the interface. A simple calculation for the adsorption energy to the interface of the nanoparticles with different surface arrangements of PS and P2VP ligands supports evidence for the rearrangement of thiol terminated homopolymers. An upper limit estimate of the adsorption energy of nanoparticles uniformly coated with a random arrangement of PS and P2VP ligands where a 10% surface area was occupied by P2VP -mers or chains was approximately 1 kBT, which indicates that such nanoparticles are unlikely to be segregated along the interface, in contrast to the experimental results for nanoparticles with mixed ligand-coated surfaces.     

In-situ atomic force microscopy (AFM) imaging: influence of AFM probe geometry on diffusion to microscopic surfaces

The effect of AFM probe geometry on diffusion to micrometer-scale reactive (electrode) interfaces is considered. A disk-shaped substrate electrode was held at a potential to reduce a species of interest (aqueous Ru(NH 3) 6 (3+)) at a diffusion-controlled rate and the current response during AFM imaging provided information on local mass transport to the interface. This approach reveals how the AFM probe influences diffusion to a reactive surface, which is of importance in more clearly delineating the conditions under which in-situ AFM can be treated as a noninvasive probe of surface processes involving mass transport (e.g., electrode reactions and crystal dissolution and growth). An assessment has been made of three types of probes: V-shaped silicon nitride contact mode probes; single beam silicon probes; and batch-fabricated scanning electrochemical-atomic force microscopy (SECM-AFM) probes. Two disk electrodes, (6.1 microm and 1.6 microm diameter) have been considered as substrates. The results indicate that conventional V-shaped contact mode probes are the most invasive and that the batch-fabricated SECM-AFM probes are the least invasive to diffusion at both of the substrates used herein. The experimental data are complemented by the development of simulations based on a simple 2D model of the AFM probe and active surface site. The importance of probe parameters such as the cantilever size, tip cone height, and cone angle is discussed, and the implications of the results for studies in other areas, such as growth and dissolution processes, are considered briefly.     

Immobilization of thiabendazole-specific monoclonal antibodies to silicon substrates via aqueous silanization

Monoclonal antibodies specific for thiabendazole were immobilized to silicon, silicon dioxide, stoichiometric silicon nitride, and silicon-rich silicon nitride surfaces. This work provides the foundation for the development of a homogeneous sensor system for rapid detection and quantification of thiabendazole residues in produce and animal tissue. Immobilization was performed via aqueous silanization of the substrate followed sequentially by treatment with glutaraldehyde and contact with antibody solution in the presence of detergent. Surfaces were challenged with thiabendazole-horseradish peroxidase conjugate in an ELISA format to estimate immobilized antibody load. A stable and reproducible surface loading of 2 x 10¹¹ antibodies/cm² was obtained only after surfaces received postimmobilization treatments to remove nonspecifically adsorbed antibody. No difference in surface loading was noted when using 30% hydrogen peroxide rather than nitric acid for silanol activation. Little difference was noted among the antibody loadings achieved on the various silicon substrates. Bound antigen-enzyme conjugate was eluted with 0.1N acetic acid and reproducible surface activity was measured for up to four consecutive antigen challenges. Immobilized antibody surfaces were stabilized with 2% sucrose, dehydrated at 37‡C and stored in vacuum or stored at 4‡C in phosphate buffered saline containing 0.01% sodium azide without significant loss of activity.     

Surfaces of fluorinated pyridinium block copolymers with enhanced antibacterial activity

Polystyrene-b-poly(4-vinylpyridine) copolymers were quaternized with 1-bromohexane and 6-perfluorooctyl-1-bromohexane. Surfaces prepared from these polymers were characterized by contact angle measurements, near-edge X-ray absorption fine structure spectroscopy and X-ray photoelectron spectroscopy. The fluorinated pyridinium surfaces showed enhanced antibacterial activity compared to their nonfluorinated counterparts. Even a polymer with a relatively low molecular weight pyridinium block showed high antimicrobial activity. The bactericidal effect was found to be related to the molecular composition and organization in the top 2-3 nm of the surface and increased with increasing hydrophilicity and pyridinium concentration of the surface.     

The role of the pH conditions of growth on the bioadhesion of individual and lawns of pathogenic Listeria monocytogenes cells

The work of adhesion that governs the interactions between pathogenic Listeria monocytogenes and silicon nitride in water was probed for individual cells using atomic force microscopy and for lawns of cells using contact angle measurements combined with a thermodynamic-based harmonic mean model. The work of adhesion was probed for cells cultured under variable pH conditions of growth that ranged from pH 5 to pH 9. Our results indicated that L. monocytogenes cells survived and adapted well to the chemical stresses applied. For all pH conditions investigated, a transition was observed in the generation time, physiochemical properties, biopolymer grafting density and bioadhesion for cells cultured in media adjusted to pH 7 of growth. In media with pH 7, the generation time for the bacterial cells was lowest, the specific growth rate constant was highest, the cells were the most polar, cells displayed the highest grafting density of surface biopolymers and the highest bioadhesion to silicon nitride in water represented in terms of the work of adhesion. When compared, the work of adhesion values quantified between silicon nitride and lawns of L. monocytogenes cells were linearly correlated with the work of adhesion values quantified between silicon nitride and individual L. monocytogenes cells.     

Nanoscale patterning of two metals on silicon surfaces using an ABC triblock copolymer template

Patterning technologically important semiconductor interfaces with nanoscale metal films is important for applications such as metallic interconnects and sensing applications. Self-assembling block copolymer templates are utilized to pattern an aqueous metal reduction reaction, galvanic displacement, on silicon surfaces. Utilization of a triblock copolymer monolayer film, polystyrene-block-poly(2-vinylpyridine)-block-poly(ethylene oxide) (PS-b-P2VP-b-PEO), with two blocks capable of selective transport of different metal complexes to the surface (PEO and P2VP), allows for chemical discrimination and nanoscale patterning. Different regions of the self-assembled structure discriminate between metal complexes at the silicon surface, at which time they undergo the spontaneous reaction at the interface. Gold deposition from gold(III) compounds such as HAuCl4(aq) in the presence of hydrofluoric acid mirrors the parent block copolymer core structure, whereas silver deposition from Ag(I) salts such as AgNO3(aq) does the opposite, localizing exclusively under the corona. By carrying out gold deposition first and silver second, sub-100-nm gold features surrounded by silver films can be produced. The chemical selectivity was extended to other metals, including copper, palladium, and platinum. The interfaces were characterized by a variety of methods, including scanning electron microscopy, scanning Auger microscopy, X-ray photoelectron spectroscopy, and atomic force microscopy.     

Diblock copolymer micellar lithography: 1. Intermicellar interactions and pathways for control of monomicellar film structure

The formation of reverse micelles of amphiphilic diblock copolymers of styrene and 2-vinylpyridine in selective (for one of the blocks) solvent (toluene) is studied by dynamic light scattering and atomic force and transmission electron microscopies, as well as by absorption spectroscopy and X-ray photoelectron spectroscopy techniques. It is revealed that the behavior of micelles of block copolymers with different ratios of block lengths and absolute molecular masses in solution is fundamentally different depending on the amount of added metal salt. The possibility of controlled variations in the characteristic sizes of two-dimensional ordered ensembles of micelles on the surface of silicon wafers is demonstrated. It is shown that, in some cases, the distance between the centers of micelles in ensemble depends on the concentration of copolymer solution and the amount of metal salt preliminarily added to the solution.     

Silicon Dioxide Coating of Titanium Dioxide Nanoparticles from Dielectric Barrier Discharge in a Gaseous Mixture of Silane and Nitrogen

The coating of titanium dioxide nanoparticles with silicon dioxide has been carried out by dielectric barrier discharge (DBD) plasma treatments to enhance the thermostability of Titania for applications at high temperature processes. During the first coating processing step, a closed film of silicon nitride was produced via plasma treatment in a gaseous mixture of silane and nitrogen, while atmospheric surface contaminations got mainly removed. In the second processing step, the DBD plasma treatment in oxygen or air was used to convert the silicon nitride mainly into silicon dioxide. Remaining carbon impurities at the interfaces between titanium dioxide and silicon nitride after the nitrogen/silane plasma treatment were subsequently removed simultaneously. Atomic force microscopy and X-ray photoelectron spectroscopy were employed to study the DBD plasma treatments of the TiO₂ nanoparticles.     

Morphology of rhenium complex-containing polystyrene-block-poly(4-vinylpyridine) and its use as self-assembly templates for nanoparticles

Polystyrene-block-poly(4-vinylpyridine) was functionalized with a chlorotricarbonyl rhenium(I) diimine complex. Compared to the metal-free copolymer, the copolymer-metal complex exhibited different morphologies, which are highly sensitive to the solvent used for spin-coating and the surface properties of the substrates. Well-defined cylindrical or spherical domains were observed. Due to its ionic nature, the poly(4-vinylpyridine)--rhenium complex block could also serve as a template for subsequent deposition of cadmium sulfide nanoparticles by electrostatic attraction. The pattern of the deposited nanoparticles was found to be the replica of the block copolymer underneath, and their presence on the film surface was confirmed by X-ray photoelectron spectroscopy.     

Kinetic studies of the reactions between silicon nitride and carbon

The reactions between silicon nitride and carbon take place in two stages, the surface silica of silicon nitride powders reacts with carbon first followed by the decomposition of silicon nitride and the residual silicon reacting with carbon. The kinetics of the two stage reactions has been studied by isothermal thermogravimetric analysis. Physico-geometric models for both of the reaction stages have been proposed, and the kinetic parameters have been calculated. The implications of the kinetic models and parameters are discussed.