Development of a solid-phase microextraction-gas chromatography-tandem mass spectrometry method for the analysis of chlorinated toluenes in environmental waters

In the present work, a simple and fast methodology has been developed for the analysis of chlorotoluenes in water samples using solid-phase microextraction (SPME) coupled to gas chromatography-tandem mass spectrometry (GC/MS/MS). A multifactorial experimental design strategy was used for studying the influence on extraction yield of factors such as fiber coating, extraction mode, temperature, and addition of sodium chloride. Quantitative recoveries (>/=84%) and satisfactory precision (relative standard deviations (RSD)相似文献   

固相微萃取气相色谱法(SPME-GC)测定水体中邻苯二甲酸酯

选用85μm PA纤维,考证了萃取温度、萃取时间、搅拌、离子强度及解析时间等影响因素,最后确立了65℃萃取温度、60min萃取时间、稳定的磁力搅拌、5min解析时间、用带电子捕获检测器的毛细管气相色谱（CGC—ECD）分离测定、外标标准曲线法定量分析水体中邻苯二甲酸酯（PAEs）的方法。该方法具有较好的精密度（RSD≤16％）和较低的检出限（DLDBP=0．003μg/L,DLDEDEHP=0．05μg/L）,水样加标回收率在70％～130％之间。用该法测定了长江水样、太湖水样、自来水及蒸馏水的PAEs含量,DBP在0．1～0．4μg/L,DEHP在0．2～1．2μg/L,DMP、DEP、DOP均未检测到。     

Development of a solid-phase microextraction method for the determination of phthalic acid esters in water

Solid-phase microextraction method (SPME) coupled to GC/ECD has been developed and validated for the determination of phthalic acid esters (dimethyl-, diethyl-, di-n-butyl-, butylbenzyl-, di-2-ethylhexyl- and di-n-octyl phthalate) in water samples. Two types of coatings (PDMS, PA), altogether four different kinds of fibers have been investigated. Both parameters affecting the partition of analytes between a fiber coating and aqueous phase (i.e. extraction time, extraction temperature, agitation) and conditions of the thermal desorption in a GC injector were optimized. The final SPME method employing the polyacrylate fiber, extraction time 20 min, heating and stirring of the sample enabled the determination of all six phthalates in water samples. The method showed linear response over four orders of magnitude and the limits of quantification of the method ranged between 0.001 and 0.050 μg l⁻¹. The repeatability expressed as R.S.D. was in the range 4-10% for the spiking level 7 μg l⁻¹ of each analyte. The applicability of the developed SPME method was demonstrated for real water samples.     

Application of dispersive liquid-liquid microextraction and high-performance liquid chromatography for the determination of three phthalate esters in water samples

A novel method, dispersive liquid-liquid microextraction (DLLME) coupled with high-performance liquid chromatography-variable wavelength detector (HPLC-VWD), has been developed for the determination of three phthalate esters (dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP)) in water samples. A mixture of extraction solvent (41 μL carbon tetrachloride) and dispersive solvent (0.75 mL acetonitrile) were rapidly injected into 5.0 mL aqueous sample for the formation of cloudy solution, the analytes in the sample were extracted into the fine droplets of CCl₄. After extraction, phase separation was performed by centrifugation and the enriched analytes in the sedimented phase were determined by HPLC-VWD. Some important parameters, such as the kind and volume of extraction solvent and dispersive solvent, extraction time and salt effect were investigated and optimized. Under the optimum extraction condition, the method yields a linear calibration curve in the concentration range from 5 to 5000 ng mL⁻¹ for target analytes. The enrichment factors for DMP, DEP and DnBP were 45, 92 and 196, respectively, and the limits of detection were 1.8, 0.88 and 0.64 ng mL⁻¹, respectively. The relative standard deviations (R.S.D.) for the extraction of 10 ng mL⁻¹ of phthalate esters were in the range of 4.3-5.9% (n = 7). Lake water, tap water and bottled mineral water samples were successfully analyzed using the proposed method.     

Determination of phthalate acid esters plasticizers in plastic by ultrasonic solvent extraction combined with solid-phase microextraction using calix[4]arene fiber

Ultrasonic solvent extraction combined with solid-phase microextraction (SPME) with calix[4]arene/hydroxy-terminated silicone (C[4]/OH-TSO) oil coated fiber was used to extract phthalate acid esters (PAEs) plasticizers in plastic, such as blood bags, transfusion tubing, food packaging bag, and mineral water bottle for analysis by gas chromatography (GC). Both extraction parameters (i.e. extraction time, extraction temperature, ionic strength) and conditions of the thermal desorption in a GC injector were optimized by analysis of eight phthalates. The fiber shows wonderful sensitivity and selectivity to the tested compounds. Owing to its high thermal stability (380 °C), the carryover effect that often encountered when using conventional fibers can be reduced by appropriately enhancing the injector temperature. The method showed linear response over two to four orders of magnitude with correlation coefficients (r) better than 0.996, and limits of detection (LOD) ranged between 0.006 and 0.084 μg l⁻¹. The relative standard deviation values obtained were ≤10%. bis-2-Ethylhexyl phthalate (DEHP) was the sole analyte detected in these plastics and recoveries were in the ranges 95.5-101.4% in all the samples.     

Applicability of headspace solid-phase microextraction to the determination of multi-class pesticides in waters

The applicability of headspace solid-phase microextraction (HS-SPME) to pesticide determination in water samples was demonstrated by evaluating the effects of temperature on the extraction of the pesticides. The evaluations were performed using an automated system with a heating module. The 174 pesticides that are detectable with gas chromatograph were selected objectively and impartially based on their physical properties: vapor pressure and partition coefficient between octanol and water. Of the 174 pesticides, 158 (90% of tested) were extracted with a polyacrylate-coated fiber between 30 and 100 degrees C and were determined with gas chromatograph-mass spectrometry. The extraction-temperature profiles of the 158 extracted pesticides were obtained to evaluate the effects of temperature on the extraction of pesticides. The pesticides were classified into four groups according to the shape of their extraction-temperature profiles. The line of demarcation between extractable pesticides and non-extractable pesticides could be drawn in the physical property diagram (a double logarithmic plot of their vapor pressure and partition coefficient between octanol and water). The plot also revealed relationships between classified extraction features and their physical properties. The new method for multi residue screening in which the analytes were categorized into sub-groups based on extraction temperature was developed. In order to evaluate the quantitivity of the developed method, the 45 pesticides were chosen among the pesticides that are typically monitored in waters. Linear response data for 40 of the 45 was obtained in the concentration range below 5 microg/l with correlation coefficients ranging between 0.979 and 0.999. The other five pesticides had poor responses. Relative standard deviations at the concentration of the lowest standard solution for each calibration curve of the pesticides ranged from 3.6 to 18%. The value of 0.01 microg/l in the limits of detection for 17 pesticides was achieved only under the approximate conditions for screening, not under the individually optimized conditions for each pesticide. Recoveries of tested pesticides in actual matrices were essentially in agreement with those obtained by solid-phase extraction.     

Solid-phase microextraction gas chromatography-mass spectrometry determination of fragrance allergens in baby bathwater

A method based on solid-phase microextraction (SPME) and gas chromatography-mass spectrometry (GC-MS) has been optimized for the determination of fragrance allergens in water samples. This is the first study devoted to this family of cosmetic ingredients performed by SPME. The influence of parameters such as fibre coating, extraction and desorption temperatures, salting-out effect and sampling mode on the extraction efficiency has been studied by means of a mixed-level factorial design, which allowed the study of the main effects as well as two-factor interactions. Excluding desorption temperature, the other parameters were, in general, very important for the achievement of high response. The final procedure was based on headspace sampling at 100 °C, using polydimethylsiloxane/divinylbenzene fibres. The method showed good linearity and precision for all compounds, with detection limits ranging from 0.001 to 0.3 ng mL⁻¹. Reliability was demonstrated through the evaluation of the recoveries in different real water samples, including baby bathwater and swimming pool water. The absence of matrix effects allowed the use of external standard calibration to quantify the target compounds in the samples. The proposed procedure was applied to the determination of allergens in several real samples. All the target compounds were found in the samples, and, in some cases, at quite high concentrations. The presence and the levels of these chemicals in baby bathwater should be a matter of concern. Baby exposure to fragrance allergens and other cosmetic ingredients through the daily bath     

Optimization of a sensitive method for the determination of nitro musk fragrances in waters by solid-phase microextraction and gas chromatography with micro electron capture detection using factorial experimental design

A solid-phase microextraction method (SPME) followed by gas chromatography with micro electron capture detection for determining trace levels of nitro musk fragrances in residual waters was optimized. Four nitro musks, musk xylene, musk moskene, musk tibetene and musk ketone, were selected for the optimization of the method. Factors affecting the extraction process were studied using a multivariate approach. Two extraction modes (direct SPME and headspace SPME) were tried at different extraction temperatures using two fiber coatings [Carboxen–polydimethylsiloxane (CAR/PDMS) and polydimethylsiloxane–divinylbenzene (PDMS/DVB)] selected among five commercial tested fibers. Sample agitation and the salting-out effect were also factors studied. The main effects and interactions between the factors were studied for all the target compounds. An extraction temperature of 100 °C and sampling the headspace over the sample, using either CAR/PDMS or PDMS/DVB as fiber coatings, were found to be the experimental conditions that led to a more effective extraction. High sensitivity, with detection limits in the low nanogram per liter range, and good linearity and repeatability were achieved for all nitro musks. Since the method proposed performed well for real samples, it was applied to different water samples, including wastewater and sewage, in which some of the target compounds (musk xylene and musk ketone) were detected and quantified. Figure Stardardized Pareto charts for the main effects and interactions     

A novel liquid-phase microextraction method combined with high performance liquid chromatography for analysis of phthalate esters in landfill leachates

A novel liquid-phase microextraction (LPME) method was presented in this paper. The most attractive feature of this method is using a polychloroprene rubber tube (PCR tube) instead of a microsyringe to load organic solvent. The PCR tube and sample vial were horizontally placed so that the selection of organic solvent was not affected by the density of extractant. Therefore, the stability of organic solvent increased and the available organic solvent was extended greatly. In this work, three phthalate esters (PAEs) (dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP)) were chosen as model analytes to testify the feasibility of the new method. A series of extraction parameters have been investigated systematically. Under the optimized condition, the method showed linear response over four orders of magnitude, ranged from 0.005 mg L⁻¹ to 50 mg L⁻¹. The correlation coefficients (r) were better than 0.997 and the limits of detection (LOD) were 0.0012 mg L⁻¹ for DMP, 0.0014 mg L⁻¹ for DEP and 0.0022 mg L⁻¹ for DnBP. Good reproducibility of extraction was acquired, the inter-day and intra-day relative standard deviation (R.S.D.) were below 7.9% and 7.4%, respectively. Recoveries that ranged from 82.7% to 116.9% were gained when the new method was used to determine three phthalate esters in landfill leachates. The enrichment factors were 5–26 for the three PAEs. The novel LPME is promising to be an alternative sample preparation method for extracting target analytes in complex sample matrices because of the simplicity, low cost and short sample preparation time.     

Optimization of ultrasound-assisted emulsification microextraction with solidification of floating organic droplet followed by high performance liquid chromatography for the analysis of phthalate esters in cosmetic and environmental water samples

Ultrasound-assisted emulsification microextraction with solidification of floating organic droplet (USAEME-SFO) followed by high performance liquid chromatography-diode array detection (HPLC-DAD), was applied for preconcentration and determination of phthalate esters in cosmetic and water samples. The effects of different variables on the extraction efficiency were studied simultaneously using an experimental design. The variables of interest in the USAEME-SFO were extraction solvent volume, salt effect, extraction time and centrifugation time. A factorial experimental design was employed for screening to determine the variables significantly affecting the extraction efficiency. Then, the significant factors were optimized by using a Box-Behnken design (BBD) and the response surface equations were derived. The optimum experimental conditions were extraction solvent volume, 30 μL; sodium chloride concentration, 20% (w/v); extraction time, 12 min and centrifugation time, 5 min. Under optimal conditions, the preconcentration factors were between 355 and 409. The limit of detections (LODs) ranged from 0.005 μg L⁻¹ (for Diethylphthalate) to 0.01 μg L⁻¹ (for Dimethylphthalate). Dynamic linear ranges; (DLRs) of 0.05-800 and 0.05-1000 μg L⁻¹ were obtained for Diisobutyl- and Dimethylphthalate, respectively. The performance of the method was evaluated for extraction and determination of phthalate esters in cosmetic and environmental water samples in micrograms per liter and satisfactory results were obtained (RSDs < 12.6%).     

Simple field‐based automated dispersive liquid–liquid microextraction of trace level phthalate esters in natural waters with gas chromatography and mass spectrometric analysis

A small, simple, and field‐based automated dispersive liquid–liquid microextraction method followed by gas chromatography mass spectrometric analysis was developed for trace level phthalate esters analysis in natural waters. With a single syringe pump that is coupled with a multiposition valve, the whole extraction procedure including cleaning, sampling, mixing of extractant and disperser solvents, extraction, phase separation, and analytes collection was carried out in a totally automated way with a sample throughput of 21 h^?1. Key factors, such as type and ratio of the extractant and disperser solvent, aspiration flow rate, extraction time, and matrix effect, were thoroughly investigated. Under the optimum conditions, linearity was found in the range from 0.03 to 60 μg/L. Limits of detection ranged from 0.0015 to 0.003 μg/L. Enrichment factors were in a range of 106–141. Reproducibility and recoveries were assessed by testing a series of three natural water samples that were spiked with different concentration levels. Finally, the proposed method was successfully applied in analysis of real surface waters. The developed system is inexpensive, light (2.6 kg), simple to use, applicable in the field, with high sample throughput, and sensitive enough for trace level phthalate esters analysis in natural waters.     

Optimization of solid-phase microextraction procedures for the determination of tricyclic antidepressants and anticonvulsants in plasma samples by liquid chromatography

Simple, sensitive, and reproducible off-line solid-phase microextraction and liquid chromatography (SPME/LC) methods are described for the determination of seven anticonvulsants and tricyclic antidepressants in human plasma. Factorial design and simplex methodology were applied in the optimization of the SPME procedure for tricyclic antidepressants analyses. Important factors in the SPME efficiency are discussed, such as the fiber coatings (both lab-made and commercial), extraction time, pH, ionic strength, influence of plasma proteins, and desorption conditions. The development of the lab-made fiber coatings, namely, octadecylsilane, aminosilane, and polyurethane, are further described and applied to anticonvulsants analyses. The investigated plasmatic range for the evaluated anticonvulsants, using CW-TPR fiber, were the following: phenylethylmalonamide (3.00–40.0 μg mL⁻¹), phenobarbital (5.00–40.0 μg mL⁻¹), primidone (3.00–40.0 μg mL⁻¹), carbamazepine and carbamazepine-epoxide (2.00–24.0 μg mL⁻¹), phenytoin (2.00–40.0 μg mL⁻¹), and lamotrigine (0.50–12.0 μg mL⁻¹). The antidepressants’ linear plasmatic concentration ranged from 75.0 to 500 ng mL⁻¹ for imipramine, amitriptyline, and desipramine, and from 50.0 to 500 ng mL⁻¹ for nortriptyline, being in all cases, the limit of quantification represented by the lowest value. The precision (interassays) for all investigated drugs in plasma sample spiked with different concentrations of each analyte and submitted to the described procedures were lower than 15%. The off-line SPME/LC methodologies developed allow anticonvulsants and antidepressants analyses from therapeutic to toxic levels for therapeutic drug monitoring.     

Development of a method based on sorbent trapping followed by solid-phase microextraction for the determination of synthetic musks in indoor air

Synthetic musks are extensively used as fragrance components in a wide range of consumer and personal care products such as detergents, shampoos, perfumes and other cosmetic products. Amongst them, galaxolide and tonalide have become ubiquitous pollutants due to their continuous releasing into the environment. Because of their nature as artificial fragrances, inhalation should be considered as an important exposure pathway, especially in indoor environments. However, up to now very few studies have been carried out to determine these emergent pollutants indoors. In this work, a simple and highly sensitive methodology for the analysis of synthetic musk fragrances in indoor air samples is presented. The proposed methodology combines solid-phase extraction (SPE) and solid-phase microextraction (SPME), followed by gas chromatography-mass spectrometry (GC/MS). To the best of our knowledge, this is the first method based on SPME for the analysis of musks in air. By active sampling, musks present in air were adsorbed onto 25mg Tenax and then transferred to a SPME fiber in the headspace mode (HS). An experimental design strategy was used to optimize main factors potentially affecting the microextraction process such as fiber coating, temperature and the addition of a microvolume of organic solvent to the solid sorbent prior to SPME. Breakthrough of the SPE sorbent was studied from 1 to 10m(3) without significant losses. Recovery studies were performed at two concentration levels (2 and 20ngm(-3)), obtaining quantitative recoveries (>/=85%) by external calibration. A comprehensive study was performed in order to estimate the limits of detection taking into account the contamination risks and laboratory blanks. Values at the sub ngm(-3) level were achieved for all the target compounds sampling 5m(3) air. External calibration, not requiring the complete sampling process, demonstrated to be suitable for the quantification of all musk compounds. Finally, several indoor environments were analyzed using the proposed method.     

Application of liquid-phase microextraction to the analysis of trihalomethanes in water

A liquid-phase microextraction method for the determination of trihalomethanes (THMs) including chloroform (CHCl₃), bromodichloromethane (CHBrCl₂), dibromochloromethane (CHBr₂Cl) and bromoform (CHBr₃) in water samples was developed, with analysis by gas chromatography-electron capture detection (GC-ECD). After the determination of the most suitable solvent and stirring rate for the extraction, several other parameters (solvent drop volume, extraction time and ionic strength of the sample) were optimized using a factorial design to obtain the most relevant variables. The optimized extraction conditions for 5 mL of sample volume in a 10 mL vial were as follows: n-hexane an organic solvent; a solvent drop volume of 2 μL; an extraction time of 5.0 min; a stirring rate of 600 rpm at 25 °C; sample ionic strength of 3 M sodium chloride. The linear range was 1-75 μg L⁻¹ for the studied THMs. The limits of detection (LODs) ranged from 0.23 μg L⁻¹ (for CHBr₂Cl) to 0.45 μg L⁻¹ (for CHCl₃). Recoveries of THMs from fortified distilled water were over 70% for a fortification level of 15 μg L⁻¹, and relative standard deviations of the recoveries were below 5%. Real samples collected from tap water and well water were successfully analyzed using the proposed method. The recovery of spiked water samples was from 73% to 78% with relative standard deviations below 7%.     

Microwave-assisted headspace solid-phase microextraction for the rapid determination of organophosphate esters in aqueous samples by gas chromatography-mass spectrometry

The rapid and solvent-free determination of organophosphate esters (OPEs) in aqueous samples via one-step microwave-assisted headspace solid-phase microextraction (MA-HS-SPME) followed by gas chromatography-mass spectrometry (GC-MS) analysis is described. Tri-n-butyl phosphate (TnBP) and tris-(2-ethylhexyl) phosphate (TEHP) were selected as model compounds for the method of development and validation. The effects of various extraction parameters for the quantitative extraction of these analytes by MA-HS-SPME were systematically investigated and optimized. The analytes, in a 20 mL water sample (in a 40 mL sample bottle containing 2 g of NaCl, pH 3.0), were efficiently extracted by a polydimethylsiloxane-divinylbenzene (PDMS-DVB) fiber placed in the headspace when the system was microwave irradiated at 140 W for 5 min. The limits of quantification (LOQs) for TnBP and TEHP were 0.5 and 4 ng/L, respectively. Using the standard addition method, MA-HS-SPME coupled with GC-MS was utilized to determine selected OPEs in surface water and wastewater treatment plants (WWTP) influent/effluent samples. Preliminary results show that TnBP was commonly detected OPEs in these aqueous samples, the correlation coefficients (r²) of the standard addition curves were greater than 0.9822, indicating that the developed method appears to be a good alternative technique for analyzing OPEs in aqueous samples.     

Analysis of polychlorinated biphenyls in aqueous samples by microwave-assisted headspace solid-phase microextraction

The hyphenated technique namely microwave-assisted headspace solid-phase microextraction (MA-HS-SPME) was developed and studied for the simultaneous extraction/enrichment of polychlorinated biphenyls (PCBs) in aqueous samples prior to the quantification by gas chromatography (GC). The PCBs in aqueous media are extracted onto a solid-phase micro fibre via the headspace with the aid of microwave irradiation. The optimum conditions for obtaining extraction efficiency, such as the extraction time, addition of salts, addition of methanol, ratio of sample to headspace volume, and the desorption parameters were investigated. Experimental results indicated that the proposed MA-HS-SPME method attained the best extraction efficiency under the optimized conditions, i.e., irradiation of extraction solution (20 ml aqueous sample in 40 ml headspace vial with no additions of salt and methanol) under 30 W microwave power for 15 cycles (1 min power on and 3 min power off of each cycle). Desorption at 270 degrees C for 3 min provided the best detection results. The detection limit obtained were between 0.27 and 1.34 ng/l. The correlation coefficient for the linear dynamic range from 1 to 80 ng/l exceeded 0.99 for 18 PCBs.     

Solid-phase microextraction of phthalate esters in water sample using different activated carbon-polymer monoliths as adsorbents

In this study, the application of different activated carbon-polymer (AC-polymer) monoliths as adsorbents for the solid-phase microextraction (SPME) of phthalate esters (PAEs) in water sample were investigated. The activated carbon (AC) was embedded in organic polymers, poly(butyl methacrylate-co-ethylene dimethacrylate) (poly(BMA-EDMA)) or poly(styrene-co-divinylbenzene) (poly(STY-DVB)), via a 5-min microwave-assisted or a 15-min water bath heating polymerization. Preliminary investigation on the performance of the native poly(BMA-EDMA) and poly(STY-DVB) demonstrated remarkable adsorption efficiencies for PAEs. However, due to the strong hydrophobic, π-π, and hydrogen bonding interactions between the analytes and polymers, low extraction recoveries were achieved. In contrast, the presence of AC in native polymers not only enhanced the adsorption efficiencies but also assisted the PAE desorption, especially for AC-poly(STY-DVB) with extraction recovery ranged of 76.2–99.3%. Under the optimized conditions, the extraction recoveries for intra-, inter-day and column-to-column were in the range of 76.5–100.8% (<3.7% RSDs), 77.2–97.6% (<5.6% RSDs) and 75.5–99.7% (<6.2% RSDs), respectively. The developed AC-poly(STY-DVB) monolithic column showed good mechanical stability, which can be reused for more than 30 extraction times without any significant loss in the extraction recoveries of PAEs. The AC-poly(STY-DVB) monolithic column was successfully applied in SPME of PAEs in water sample with extraction recovery ranged of 78.8%–104.6% (<5.5% RSDs).     

固相微萃取-气相色谱质谱法联用测定水体中痕量多环麝香类化合物

采用固相微萃取-气相色谱质谱法联用测定了水体中痕量多环麝香类化合物。对固相微萃取条件和解析条件进行了优化,确定了微萃取条件为:选用65μmPDMS-DVB萃取头、顶空萃取模式(HS),在800 r/min,60℃条件下,萃取45 min;萃取过程中保持pH 7并且不加入NaCl;解析条件为:解析时间为3 min,插入GC深度为4 cm,进样口温度为250℃。方法的检测限为0.29～0.37 ng/L,线性范围5～1000ng/L,相对标准偏差1.5%～2.2%。对实际污水厂不同类型的水样使用优化后的实验条件进行了验证试验,目标化合物的回收率在82.5%～92.8%之间,表明优化后的试验条件适用于实际水体中痕量多环麝香类化合物的分析测定。     

Determination of organochlorine pesticides in water using microwave assisted headspace solid-phase microextraction and gas chromatography

A coupled technique, microwave-assisted headspace solid-phase microextraction (MA-HS-SPME), was investigated for one-step in situ sample pretreatment for organochlorine pesticides (OCPs) prior to gas chromatographic determination. The OCPs, aldrin, o,p'-DDE, p,p'-DDE, o,p'-DDT, p,p'-DDT, dieldrin, alpha-endosulfan, beta-endosulfan, endosulfan sulfate, endrin, delta-HCH, gamma-HCH, heptachlor, heptachlor epoxide, methoxychlor and trifluralin were collected by the proposed method and analyzed by gas chromatography with electron-capture detection (GC-ECD). To perform the MA-HS-SPME, six types of SPME fibers were examined and compared. The parameters affecting the efficiency in MA-HS-SPME process such as sampling time and temperature, microwave irradiation power, desorption temperature and time were studied to obtain the optimal conditions. The method was developed using spiked water samples such as field water and with 0.05% humic acid in a concentration range of 0.05-2.5 microg/l except endosulfan sulfate in 0.25-2.5 microg/l. The detection was linear over the studied concentration range with r2>0.9978. The detection limits varied from 0.002 to 0.070 microg/l based on S/N=3 and the relative standard deviations for repeatability were <15%. A certified reference sample of OCPs in aqueous solution was analyzed by the proposed method and compared with the conventional liquid-liquid extraction procedure. These results are in good agreement. The results indicate that the proposed method provides a very simple, fast, and solvent-free procedure to achieve sample pretreatment prior to the trace-level screening determination of organochloride pesticides by gas chromatography.     

Screening method for phthalate esters in water using liquid-phase microextraction based on the solidification of a floating organic microdrop combined with gas chromatography-mass spectrometry

A simple and efficient liquid-phase microextraction (LPME) technique was developed using directly suspended organic microdrop coupled with gas chromatography–mass spectrometry (GC–MS), for the extraction and the determination of phthalate esters (dimethyl phthalate, diethyl phthalate, diallyl phthalate, di-n-butyl phthalate (DnBP), benzyl butyl phthalate (BBP), dicyclohexyl phthalate and di-2-ethylhexyl phthalate (DEHP)) in water samples. Microextraction efficiency factors, such as nature and volume of the organic solvent, temperature, salt effect, stirring rate and the extraction time were investigated and optimized. Under the optimized extraction conditions (extraction solvent: 1-dodecanol; extraction temperature: 60 °C; microdrop volume: 7 μL; stirring rate: 750 rpm, without salt addition and extraction time: 25 min), figures of merit of the proposed method were evaluated. The values of the detection limit were in the range of 0.02–0.05 μg L⁻¹, while the R.S.D.% value for the analysis of 5.0 μg L⁻¹ of the analytes was below 7.7% (n = 4). A good linearity (r² ≥ 0.9940) and a broad linear range (0.05–100 μg L⁻¹) were obtained. The method exhibited enrichment factor values ranging from 307 to 412. Finally, the designed method was successfully applied for the preconcentration and determination of the studied phthalate esters in different real water samples and satisfactory results were attained.