New design of a beam-steering thermooptic multimode polymer waveguide switch

We present simulations of a Y-branch directional coupler activated using the thermooptic effect in a multimode polymer waveguide. Microheaters embedded beneath both sides of the waveguide at the Y-branch are used to generate an inhomogeneous temperature profile. Through the thermooptic effect, this temperature profile creates a refractive index profile in the channel waveguide material, which steers the beam to one of the two output branches. We determined the expected thermal profiles using finite element modeling (FEM). The transmission of a basic mode through the waveguide was then simulated using the beam propagation method (BPM). The results show that a high contrast ratio (>90%) can be achieved in response times on the order of 1 ms. Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.PACS 42.82.Et; 42.70.Jk; 42.79.Ta     

Light-propagation characteristics of Y-branch defect waveguides in AlGaAs-based air-bridge-type two-dimensional photonic crystal slabs

Y-branch defect waveguides (DWGs) in an AlGaAs-based air-bridge-type two-dimensional (2D) photonic crystal (PC) slab were fabricated, and the resulting optical transmission spectra were measured. Optical beam propagation along the waveguide was successfully observed in vidicon IR images. The measured transmission spectra at the two output ports in the Y-branch DWG were remarkably similar in shape and magnitude. From comparison between the measured and calculated transmission spectra, the observed optical beam was identified as the guided mode based on the Y-branch DWG in the 2D PC slab. The results suggest that the Y-branch DWG used in the experiment has the potential to function as an ultrasmall 3-dB beam splitter with good performance.     

质子交换Y分支光波导弯曲损耗研究

对采用退火质子交换技术(APE)制备的具有正弦型弯曲和余弦型弯曲两种不同的S型弯曲的Y分支光波导,利用宽角有限差分光束传播法,就过渡区长度、波导表面折射率增量、掩模版开口宽度等对波导弯曲损耗的影响进行了研究。结果表明,两种S弯曲下的Y分支波导的弯曲损耗,随波导结构参数的变化基本上是相同的,但二者的表现并不完全一致。数值计算结果为相应波导器件的设计和制备提供了一定的参考。     

扩展多模波导全内反射型Y分叉开关的分析

利用全内反射和波导理论，分析了多模波导反射区全内反射(Total Internal Reflection，TIR)型光开关的物理模型和降低串音和损耗的原因，给出改进Y分叉全内反射型光开关特征的近似计算方法。数值模拟表明，扩展多模波导的Y分叉全内反射开关的串音和损耗可分别下降15．5dB和0．65dB以上。     

FDTD Studies of Metallic Cylinder Arrays： Plasmon Waveguide and Y-Splitter

The plasmon waveguide based on double chain of gold cylinders is studied using the finite-difference time-domain method （FDTD）. The wavelength of the incident Gaussian beam ranges from 650 to 1200nm, and the corresponding attenuation factors are calculated. We also present a Y-splitter with 90° splitting angle, each branch in the form of double chains. The transmission efficiencies for different wavelengths are evaluated.     

Evanescent-wave-coupled optical light beam deflector with symmetrical structure

We purpose a waveguide optical deflector using a Y-branch waveguide coupled to a slab waveguide via gaps between them. Narrow stripe electrodes placed on the Y-branch waveguide enables a fast deflection. A symmetrical light beam with low side lobes is generated by a simple structure.     

Wide-angle low-loss waveguide branching for integrated optics

A new wide-angle, low-loss, symmetrical Y-branch waveguide is proposed. The waveguide configuration utilizes ribs for lateral confinement in the planar guiding region underneath. This Y-branch structure can be fabricated easily without an additional process step. Together with a utilization of the multimode interference effect, a local decrease of the waveguide ridge in the wedge part of the Y-branch reduces the radiation loss. When proper@ designed, the proposed Y-branch has a radiation loss as low as 2.2 dB at a branch angle of 6° with the index difference (Δn/n) as small as 7.1 × 10^-4 at a wavelength of 870 nm in the TE fundamental mode as compared to 12.6 dB for a conventional Y-branch. The proposed method yields corresponding advantages for waveguide designs with a higher Δn/n ratio and can also be adapted in combination with S-branch designs.     

SiO2 Waveguide Resonator Used in an Integrated Optical Gyroscope

An integrated optical waveguide resonator based on a SiO2 waveguide is proposed, fabricated and tested. The method of designing the resonator is also presented. The optimal splitting ratio of the coupler is gained by simulating the relationship between the splitting ratio of the key coupler in the resonator and the resonator＇s finesse with resonance depth. The calculated fundamental detection limit of this integrated optical vcaveguide resonator is 1.6°/h. Finally, a micro-optical gyroscope system based on the integrated waveguide resonator is built, and the measured resonator＇s finesse F is close to 70 under fluctuating temperature. To the best of our knowledge, the present F is the best result to date. For the coupler splitting rate the experimental results have fixed errors with the simulation results caused by fabrication processes which can be easily eliminated, implying that the method of design is effective and applicable.     

基于表面等等离波子的新型Y分支波导

新型高效的纳米光波导器件的研制纳米集成光学的核心技术之一。Y分支波导作为最基本的分光和光路连接元件是纳米光学器件设计与制备的基础。运用时域有限差分(FDTD)法,模拟计算了基于表面等等离波子(SPP)的纳米Y分支波导的传输特性。结果表明,该新型Y分支波导在光通信波段可以实现大角度的分光功能,且在180°分支情况下,传输效率仍高达92.8%以上。另外,该波导还具有导波性能良好、对分叉处间隙缺陷大小不敏感及制作容差较大和器件尺寸在纳米量级等特点。对该新型光波导器件的研究为未来纳米集成光学器件的研制和应用有一定的指导意义。     

Fabrication of single-mode Y-branch waveguides in photosensitive polymer with reduced Y-junction residue

Single-mode small-core (～2 μm × 2 μm) Y-branch waveguide structures in photosensitive polymer have been fabricated. Y-branch waveguides are designed by the beam propagation method and Y-branch waveguides are obtained on development after a cross-linkable negative tone epoxy SU-8 2002 polymer is exposed to UV through a photomask. Optical Adhesive NOA 61 is used as under- and over-clad. The fabrication process is optimized to avoid polymer residue at the Y-junction. The average insertion loss obtained for a 7.2 mm 1 × 2 device at chip-level is ～13 dB at 1550 nm.     

Laser diode integrated with a low radiation loss thickness-tapered beam expander for highly efficient fiber coupling

The optimal structure of a laser diode monolithically integrated with a thickness-tapered beam expander waveguide is demonstrated by analyzing the relationship between fiber coupling efficiencies and radiation losses. It is also found that mode conversion loss is lowered in a ridge waveguide structure than in a buried hetero structure under equivalent fiber coupling. A fabricated ridge waveguide device based on this design shows threshold current as low as 16 mA and narrow beam divergences of 13° and 12°.     

Experimental observation and numerical simulation of guided modes in Nd:YLiF4 channel waveguides produced by carbon ion implantation

We report on, to our knowledge the first time, the channel waveguide formation in Nd:YLiF₄ laser crystal produced by 6 MeV carbon ion implantation. The guided modes are observed by using an end‐face arrangement. We construct the two‐dimensional (2D) refractive index profile of the channel waveguide cross section, which is based on the related planar waveguide index distribution as well as the rectangular shape of the waveguide cross sections. The modal intensity distribution is numerically calculated by using the beam propagation method according to the reconstructed index profile, which shows a reasonable agreement with the experimental result. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

BPM Simulation and Comparison of 1 × 2 Directional Waveguide Coupling and Y-Junction Coupling Silicon-on-Insulator Optical Couplers

For developing large area opto-electronic silicon-on-insulator (SOI) devices, the optical coupler is a basic key device. In this article, the authors design and simulate 1 2 2 directional waveguide coupling and Y-branch coupling optical couplers based on Unibond SOI rib waveguides. The beam propagation method (BPM) is used for light propagation analysis. The simulation results and comparisons of the two kinds of optical couplers are reported. The S-bend waveguide for attaching to the two kinds of SOI optical coupler is also analyzed by BPM. We find that the directional coupler has lower power loss, but the Y-junction coupler is more wavelength insensitive with the same device size and splitting angle. The fabrication tolerance analysis shows Y-junction coupler has better fabrication characteristics.     

带有矩形过渡区的非对称Y分支光波导

提出了带有矩形过渡区的非对称Y分支光波导的两种设计方案。分别通过设置两分支波导不同的宽度和改变分支波导与矩形中心的轴偏移量,去获得非对称分支比。采用有限差分光束传播法（FD-BPM）对两种结构进行模拟,得出它们的分支比和损耗。分支比分别最高可达809／6和72．9％,其相对应的损耗分别低于0．12dB和0．23dB,充分证明了方案的可行性,为以后非对称Y分支光波导的制作提供了实验基础。     

集成光学平板光盘读出头研制

采用集成光学方法,将非球面消球差双凸波导透镜、双光栅会聚光波导透镜、光波导转向棱镜单片集成在铌酸锂基底上构成光学平板光盘读出头.集成光学平板光盘读出头克服了微透镜光盘读出头体积大、组装复杂的不足,实现了光盘读出头的集成化,提高了系统的可靠性.光斑理论值0.475 μm,实测值0.67 μm.     

特种非对称低损耗1×5光分路器

设计和优化了一种新型低损耗、低偏振的基于二氧化硅的特种非对称1×5光分路器.在设计Y分支结构时,输入端采用缓变展宽波导结构和直波导过渡波导相结合的结构,此结构可以使输入光场缓慢展宽,进行分束前的准备,大大减小分支结构的辐射损耗和模式转换损耗.非对称1×5光分路器第一个端口输出功率占50%,第二至五端口输出功率占50%.利用三维光束传播法模拟和优化了特种非对称1×5光分路器,模拟结果表明,该结构具有均匀性好、器件尺寸小、低损耗和低偏振等优点,1×5光分路器在1 250~1 650 nm波长范围内,第一个输出端口附加损耗小于0.07 dB,均匀性小于0.023 dB,偏振相关损耗小于0.009 dB,第二到五端口附加损耗小于0.45 dB,均匀性小于0.41 dB,偏振相关损耗小于0.06 dB.     

Optimized design of a new three branch optical waveguide

A new type of 1 × 3 Y-branch optical waveguide structure with a cone transitional section is introduced in this paper. The symmetrical branch ratio of the 1 × 3 Y branch optical waveguide is obtained by changing the width of this waveguide. The loss and the uniformity are obtained by using the finite difference beam propagation methods, and their values are 0.2 dB and 0.05 dB, respectively. Therefore, it provides some experimental basis for production of three branch optical waveguide.     

A Defect Effect to Light Transmission through Acute Bending Coupled Cavity Waveguide in a Two-Dimensional Photonic Crystal

Light propagation through a coupled-defect waveguide with a 63.5° bend in a two-dimensional （2D） photonic crystal is investigated. The waveguide modes are non-degenerate monopole state and dipole defect state of a square lattice for two different branches. To increaze the transmission in the bending waveguide, we propose a method to rotate the localized state by introducing a cavity. The higher coupling efficiency and transmission shift. new type defect with a sheared square rod into coupled in the bending waveguide are obtained with proper shear     

基于光纤反射腔的高灵敏电流传感器方案

提出了一种基于平面Y分支波导与法拉第旋镜的高灵敏度光纤电流传感器结构方案。利用两个法拉第旋镜与平面Y分支波导构成一个光纤反射腔,通过光在腔中的多次反射来增加待测电流导致的传感光纤中的法拉第相移,从而实现对微弱电流的测量。该结构方案中首次采用了平面Y分支光波导,从而可降低光路系统损耗,增加灵敏度,为微弱电流测量的工程化提供了一种可行的方法。     

质子交换LiNbO3波导调制器多模截止波长的测试技术研究

提出并实验了一种采用倒置输入的结构来测定Y分支LiNbO3波导相位调制器的多模截止波长的新方法,模式耦合分析表明,倒置输入的Y分支波导的多模传输的输出功率具有随波长变动发生振荡的特征,该特征可用于定量判定多模截止波长.方法的有效性得到了波束传播法(BPM)仿真和样品实验两方面的验证.