Investigation on The Thermal Properties of Fe2O(SO4)2. Part II

Fe₂O(SO₄)₂ is a secondary product of the decomposition of FeSO₄⋅H₂O. Part I of this study presents results on the synthesis of Fe₂O(SO₄)₂ in gaseous environment containing either low or high concentration of oxygen. In this paper the existence of differences between the structures of Fe₂O(SO₄)₂ and Fe₂(SO₄)₃ is proved on the basis of a detailed thermal study of Fe₂O(SO₄)₂ upon dynamic heating (differential thermal analysis) and upon isothermal heating (thermal-analytic balance) in various gaseous environments as well as by presenting kinetic data on the processes of decomposition of both compounds. This revised version was published online in July 2006 with corrections to the Cover Date.     

TG/DTA/MS Study of the thermal decomposition of FeSO4·6H2O

The thermal decomposition of FeSO₄·6H₂O was studied by mass spectroscopy coupled with DTA/TG thermal analysis under inert atmosphere. On the ground of TG measurements, the mechanism of decomposition of FeSO₄·6H₂O is: i) three dehydration steps FeSO₄·6H₂O FeSO₄·4H₂O+2H₂O FeSO₄·4H₂O FeSO₄·H₂O+3H₂O FeSO₄·H₂O FeSO4+H₂O ii) two decomposition steps 6FeSO₄ Fe₂(SO₄)₃+2Fe₂O₃+2SO₂ Fe₂(SO₄)3 Fe₂O₃+3SO₂+3/2O₂ The intermediate compound was identified as Fe₂(SO₄)₃ and the final product as the hematite Fe₂O₃.     

Synthesis and thermal investigation of Na2Cd(SO4)2·2H2O

The synthesis and thermal decomposition of Na₂(SO₄)₂·2H₂O in both air and nitrogen are described. The synthesis was performed by two different procedures, but in both cases the same product was obtained, corresponding to the general formula given above. The crystals obtained were investigated by methods of X-ray powder diffraction, and chemical and thermal analysis. The differences in thermal decomposition in air and nitrogen are discussed.     

Tribochemistry and kinetics of Al2(SO4)3·xH2O decomposition

The thermal decomposition of tribochemically activated Al₂(SO₄)₃·xH₂O was studied by TG, DTA and EMF methods. For some of the intermediate solids, X-ray diffraction and IR-spectroscopy were applied to learn more about the reaction mechanism. Thermal and EMF studies confirmed that, even after mechanical activation of Al₂(SO₄)₃·xH₂O, Al₂O(SO₄)₂ is formed as an intermediate. Isothermal kinetic experiments demonstrated that the thermochemical sulphurization of inactivated Al₂(SO₄)₃·xH₂O has an activation energy of 102.2 kJ·mol^?1 in the temperature range 850–890 K. The activation energy for activated Al₂(SO₄)₃·xH₂O in the range 850–890 K is 55.0 kJ·mol^?1. The time of thermal decomposition is almost halved when Al₂(SO₄)₃·xH₂O is activated mechanically. The results permit conclusions concerning the efficiency of the tribochemical activation of Al₂(SO₄)₃·xH₂O and the chemical and kinetic mechanisms of the desulphurization process.     

Fe2(SO4)3·xH2O-catalyzed per-O-acetylation of sugars compatible with acid-labile protecting groups adopted in carbohydrate chemistry

Fully acetylated saccharides are inexpensive and very useful starting materials for the synthesis of many naturally occurring glycosides, oligosaccharides, and glycoconjugates. Ferric sulfate hydrate (Fe₂(SO₄)₃·xH₂O) was found to be a valuable Lewis acid promoter in the per-O-acetylation reaction of saccharides with acetic anhydride in 100% of conversion rate and 88-99% yields. Interestingly, the procedure is perfectly compatible with the presence of a variety of acid-labile protecting groups, such as isopropylidene, benzylidene, trityl, and TBDMS groups. The reactions were simply performed by stirring the mixture of a sugar with a slight excessive acetic anhydride in the presence of 2.0 mol % of Fe₂(SO₄)₃·xH₂O at rt and the pure products were obtained by a simple dilution of the reaction mixture with dichloromethane and washings with aqueous Na₂CO₃.     

Ferric sulfate [Fe2(SO4)3·xH2O]: an efficient heterogeneous catalyst for the synthesis of tetrahydroquinoline derivatives using Povarov reaction

Fe₂(SO₄)₃·xH₂O can be used as an efficient and reusable catalyst for the synthesis of pyrano- and furanotetrahydroquinolines via one-pot three-component Povarov reaction involving aromatic aldehydes, aromatic amines, and cyclic enol ethers. The catalyst is recyclable, economically viable, and environmentally benign. This protocol provides good yields and diastereoselectivity as well as applicability on a wide range of substrates.     

Accuracy in the Isotope Dilution Mass Spectrometry of Uranium in Rubidium Uranium Sulphate Rb2U(SO4)3

Abstract

Problems encountered in the determination of uranium in rubidium uranium sulphate (Rb₂U(SO₄)₃) employing isotope dilution thermal ionisation mass spectrometry (ID-TIMS) are discussed. The positive bias of 0.2 to 0.3% in the determination of uranium in Rb₂U(SO₄)₃ by ID-TIMS with respect to the stoichiometric composition has been resolved by modifying the chemical exchange procedures. The concentration of uranium in Rb₂U(SO₄)₃ could be determined with an accuracy better than 0.1% employing the HClO₄ treatment for proper isotopic exchange between the spike and sample isotopes.     

Preparation of ethyl levulinate from wheat stalk over Zr(SO4)2/SiO2

A series of Zr(SO₄)₂/SiO₂ solid acid catalysts with different Zr(SO₄)₂ loadings were prepared by water-soluble-impregnation method at room temperature. Then, the prepared catalysts were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy and energy-dispersive X-ray spectrum, X-ray diffraction, adsorption/desorption of N₂, and temperature-programmed desorption of NH₃. The results showed that the active component Zr(SO₄)₂ was successfully adhered to the mesoporous SiO₂, and the acid amount of Zr(SO₄)₂/SiO₂ increased with the increasing of the Zr(SO₄)₂ loadings. Finally, the wheat stalk was used as raw material and depolymerized over Zr(SO₄)₂/SiO₂ to produce ethyl levulinate (EL). The reaction mixture was separated and purified by filtration and vacuum distillation. The kinetic characteristics and the reaction pathway were also studied. A comparative study showed that 20 wt.% Zr(SO₄)₂/SiO₂ exhibited higher catalytic activity. When reaction temperature, time, catalyst dosage and Zr(SO₄)₂ loadings were 190 °C, 50 min, 20 wt.% and 30 wt.%, the EL yield reached a maximum of 17.14%. The relative content of EL exceeded 90% after three steps of distillation.     

Two Ce(SO4)2·4H2O polymorphs: Crystal structure and thermal behavior

Syntheses, crystal structures and thermal behavior of two polymorphic forms of Ce(SO₄)₂·4H₂O are reported. The first modification, α-Ce(SO₄)₂·4H₂O (I), crystallizes in the orthorhombic space group Fddd, with a=5.6587(1), b=12.0469(2), c=26.7201(3) Å and Z=8. The second modification, β-Ce(SO₄)₂·4H₂O (II), crystallizes in the orthorhombic space group Pnma, with a=14.6019(2), b=11.0546(2), c=5.6340(1) Å and Z=4. In both structures, the cerium atoms have eight ligands: four water molecules and four sulfate groups. The mutual position of the ligands differs in (I) and (II), resulting in geometrical isomerism. Both these structures are built up by layers of Ce(H₂O)₄(SO₄)₂ held together by a hydrogen bonding network. The dehydration of Ce(SO₄)₂·4H₂O is a two step (I) and one step (II) process, respectively, forming Ce(SO₄)₂ in both cases. During the decomposition of the anhydrous form, Ce(SO₄)₂, into the final product CeO₂, intermediate xCeO₂·yCe(SO₄)₂ species are formed.     

Degradation thermique et etude vibrationnelle de MII(NH4)4(P3O9)2x4H2O(M II=Cu2+, Ni2+, Co2+)

We have studied the thermal behaviour under atmospheric pressure of isotypic tetrahydrate cyclotriphosphates M^II(NH₄)₄(P₃O₉)₂x4H₂O (M ^II=Cu, Ni and Co), between 25 and 1400°C, by X-ray diffraction, thermal analyses (TG and DTA) and infrared spectrometry. This study shows that the series of the compounds M^II(NH₄)₄(P₃O₉)₂x4H₂O (M ^II=Cu, Ni and Co) after elimination of water, in two different stages, and ammonia leads, at 400°C to cyclotetraphosphate M₂ ^IIP₄O₁₂ crystallized and to a thermal residue with a formula H₄P₄O₁₂ which undergoes under a thermal degradation by evolving water and pentoxide phosphorus. The kinetic characteristics of the dehydration and elimination of ammonia have been determinated. The vibrational spectra of Cu(NH₄)₄(P₃O₉)₂x4H₂O were examined and interpreted, in the domain of the valency frequencies, on the basis of the crystalline structure of its isotypic compound Co(NH₄)₄(P₃O₉)₂x4H₂O whose cycle has the site symmetry C₁, of our results of the calculation of the IR frequencies and the successive isotopic substitutions of the equivalent atoms (3P, 3Oi and 6Oe belonging to the P₃Oi₃Oe₆ ring) of the P₃O₉ ³⁻ cycle with high symmetry D_3h. This revised version was published online in August 2006 with corrections to the Cover Date.     

热力学模型研究KNO3-K2SO4-H2O和KNO3-KCl-H2O体系溶解度

用Pitzer-Simonson-Clegg热力学模型(PSC模型),分别拟合KCl-H2O、K2SO4-H2O、KNO3-H2O体系以及KNO3-K2SO4-H2O和KNO3-KCl-H2O体系水活度和溶解度实验数据,得到二元参数和三元离子相互作用参数,并以此计算3个二元盐水体系溶解度相图,及2个三元盐水体系在不同温度下的溶解度,结果表明计算值与实验值一致。     

Interaction Between Two Similar Plane Parallel Double Layers for (NH4)2Fe(SO4)2 or (NH4)2Cu(SO4)2 Type Complex Salt Electrolytes at Positive Surface Potential

Interaction energies between two similar plane parallel double layers for (NH₄)₂Fe(SO₄)₂ or (NH₄)₂Cu(SO₄)₂ type complex salt electrolytes at positive surface potential were expanded in a power series and accurate numeral results were given for 0.1 ≤ y _e  < y ₀ ≤ 20. The general expressions were given for the interaction energies of A _ν +B _ν′ +C_ν? type complex salt electrolytes at y > 0. The interaction energies for simple salts NaCl, CaCl₂, Na₂SO₄, FeCl₃, Na₃PO₄, Mg₃(PO₄)₂, Al₂(SO₄)₃, and complex salts (NH₄)₂Fe(SO₄)₂ or (NH₄)₂Cu(SO₄)₂ at y ₀ = 1 were compared. There was hardly difference between these simple salts and this complex salt for the interaction energies. The interaction energy for complex salt (NH₄)₂Fe(SO₄)₂ was close to that for simple salt Na₃PO₄.

Supplemental files are available for this article. Go to the publisher's online edition of the Journal of Dispersion Science and Technology to view the free supplemental file.     

The effect of experimental methods and measurement conditions on values of the kinetic parameters of [Co(NH3)6]2(C2O4)3·4H2O

Using the thermal decomposition of [Co(NH₃)₆]₂(C₂O₄)₃·4H₂O as a basis, the paper presents results which show how computed values of kinetic parameters are influenced by experimental conditions (ambient atmosphere, sample mass, linear heating rate) when using the non-isothermal methods and the Coats-Redfern (CR) modified equation. It also illustrates the influence of the experimental methods i.e. non-isothermal and isothermal (conventional) methods and also a quasiisothermal-isobaric one which can be recognised as equivalent to Constant Rate Thermal Analysis (CRTA). The results obtained have confirmed the significant influence of the experimental parameters as well as that of the experimental method used on the estimated values of kinetic parameters. The correlation between activation energy (E) and sample mass (m) or heating rate (β) is generally of a linear nature:E=a+bx     

可回收Fe3O4@SiO2-Ag磁性纳米微球对染料污染物的快速脱色处理

介绍了一种采用无毒廉价的前驱物制备Fe₃O₄@SiO₂-Ag磁性纳米微球的快捷方法,制备的Fe₃O₄@SiO₂-Ag纳米微球在NaBH₄存在下可以催化还原染料污染物.实验结果表明,Fe₃O₄@SiO₂-Ag磁性纳米粒子保持了Ag纳米粒子和Fe₃O₄纳米粒子的双重优点,不仅对染料罗丹明B和曙红Y具有良好的催化还原效率,而且可以在外加磁场作用下从溶液中快速有效的分离.催化还原反应速率与反应温度及Fe₃O₄@SiO₂-Ag催化剂用量有关,反应体系中表面活性剂和无机盐(Na₂SO₄)的存在也会影响催化剂的催化活性.该Fe₃O₄@SiO₂-Ag磁性纳米粒子在工业染料污染物处理方面具有应用前景.     

Breakdown of the Rule of “Linearity of Water Isoactivity Lines” in a System Containing Solid Solutions

Osmotic coefficients of water have been measured isopiestically for the entire region of homogeneous ternary solutions for the Rb₂SO₄- (NH₄)₂SO₄-H₂O system at 25°C. One might expect that water isoactivity lines should be straight since this system involves a continuous series of solid solutions. The related systems (K₂SO₄-Rb₂SO₄-H₂O and (K₂SO₄- (NH₄)₂ SO₄-H₂O) obey the linearity of water isoactivity lines rule. Contrary to expectations, the (Rb₂SO₄-(NH₄)₂-SO₄-H₂O appears to be the first water–salt system containing continuous solid solutions in which the mentioned rule is not obeyed.     

Gas-phase reactions of SF5, SF2, and SOF with O(3 P): Their significance in plasma processing

Reactions of both SF₅ and SF₂ with O(³ P) and molecular oxygen have been studied at 295 K in a gas flow reactor sampled by a mass spectrometer. For reactions with O(³ P), rate coefficients of (2.0±0.5)×10^–11 cm³ s^–1 and (10.8±2.0)×10^–11 cm³ s^–1 were obtained for SF₅ and SF₂ respectively. The rate coefficients for reactions with O₂ are orders of magnitude lower, with an estimated upper limit of 5×10^–16 cm³ s^–1 for both SF₅ and SF₂. Reaction of SF₂ with O(³ P) leads to the production of SOF which then reacts with O(³ P) with a rate coefficient of (7.9±2.0)×10^–11 cm³ s^–1. Both SO and SO₂ are products in the reaction sequence initiated by reaction between SF₂ and O(³ P). Although considerable uncertainty exists for the heat of formation of SOF, it appears that SO arises only from reaction between SOF and O atoms which is also the source of SO₂. These results are discussed in terms of a reaction scheme proposed earlier to explain processes occurring during the plasma etching of Si in SF₆/O₂ plasmas. A comparison between the results obtained here and those reported earlier for reactions of both CF₃ and CF₂ with O and O₂ shows that there is a marked similarity in the free radical chemistry which occurs in SF₆/O₂ and CF₄/O₂ plasmas.     

Isothermal investigation of decomposition of FeSO4·H2O-BaO2 mixtures

Isothermal studies were conducted on mixtures of Fe₂SO₄·H₂O in BaO₂ in molar ratios ofn=4, 2 and 1 at temperatures of 573 and 1073 K, in a closed crucible, in air as gas medium. The solid products of decomposition were investigated by means of X-ray analysis, Mössbauer spectroscopy and electron spectroscopy.The experiments revealed that the mechanism of the process is connected with the formation of different quantities of barium ferrites (BaFeO₃, BaFe₂O₄ and BaFe₁₂O₁₉), as well as BaSO₄ and Fe₂O₃, depending on the quantity of BaO₂ in the initial mixture, the partial pressure of the gas components and temperature. Differences were found in the mechanism of the process for the same mixtures under dynamic temperature conditions.     

Investigation of Solid-Solid Interactions between Pure and Li2O-Doped Magnesium and Ferric Oxides

The results obtained showed that the addition of small amounts of LiNO₃ to the reacting mixed solids, consisting of equimolar proportion of Fe₂O₃ and basic MgCO₃ much enhanced the thermal decomposition of magnesium carbonate. The addition of 12 mol% LiNO₃ (6 mol% Li₂O) decreased the decomposition temperature of MgCO₃ from 525.5 to362°C. MgO underwent solid–solid interaction with Fe2O3 at temperatures starting from800°C yielding MgFe₂O₄. The amount of ferrite produced increased by increasing the precalcination temperature of the mixed solids. However, the completion of this reaction required prolonged heating at elevated temperature above 1100°C. Doping with Li₂O much enhanced the solid–solid interaction between the mixed oxides leading to the formation of MgFe₂O₄ phase at temperatures starting from 700°C. The addition of 6 mol% Li₂O to the mixed solids followed by precalcination at 1050°C for 4 h resulted in complete conversion of the reacting oxides into magnesium ferrite. The heat treatment of pure and doped solids at 900–1050°C effected the disappearance of most of IR transmission bands of the free oxides with subsequent appearance of new bands characteristic for MgFe₂O₄ structure. The promotion effect of Li2O towards the ferrite formation was attributed to an effective increase in the mobility of the various reacting cations. The activation energy of formation (ΔE) of magnesium ferrite was determined for pure and variously doped solids and the values obtained were 203, 126, 95 and 61 kJ mol⁻¹ for pure mixed solids and those treated with 1.5, 3.0 and 6.0 mol% Li₂O, respectively. This revised version was published online in August 2006 with corrections to the Cover Date.     

Silica-gel-supported Ce(SO4)2·4H2O-mediated cyclization of 2′-amino and 2′-hydroxychalcones under solvent-free conditions

A simple, efficient, and environmentally friendly approach for the synthesis of flavones, aza-flavones, and aza-flavanones from corresponding 2′-hydroxy or 2′-aminochalcones has been developed. The reactions are successfully conducted in presence of silica-gel-supported Ce(SO₄)₂·4H₂O under solvent-free conditions.     

NMR relaxation study of the phase transitions and relaxation mechanisms of the alums MCr(SO4)2·12H2O (M=Rb and Cs) single crystals

The physical properties and phase transition mechanisms of MCr(SO₄)₂·12H₂O (M=Rb and Cs) single crystals have been investigated. The phase transition temperatures, NMR spectra, and the spin-lattice relaxation times T₁ of the ⁸⁷Rb and ¹³³Cs nuclei in the two crystals were determined using DSC and FT NMR spectroscopy. The resonance lines and relaxation times of the ⁸⁷Rb and ¹³³Cs nuclei undergo significant changes at the phase transition temperatures. The sudden changes in the splitting of the Rb and Cs resonance lines are attributed to changes in the local symmetry of their sites, and the changes in the temperature dependences of T₁ are related to variations in the symmetry of the octahedra of water molecules surrounding Rb⁺ and Cs⁺. We also compared these ⁸⁷Rb and ¹³³Cs NMR results with those obtained for the trivalent cations Cr and Al in MCr(SO₄)₂·12H₂O and MAl(SO₄)₂·12H₂O crystals.