微针肋槽道内去离子水换热特性

设计了槽肋比为1:2和2:1的矩形大长宽比微针肋散热器,并实验研究了去离子水在其内的流动换热性能。结果表明:当进口温度为40 ℃、微针肋槽道在雷诺数小于650、最高壁面温度低于77 ℃时,单位面积散热量可达21.32 W/cm2。当雷诺数一定时,同一个槽道壁面温度沿着流动方向不断增加、同一个位置壁面温度随着加热功率的增加而增大,局部努谢尔数沿着流动方向先减小后逐渐增加并趋于定值。当针肋流动换热长度较长时,其入口效应可以忽略,槽道平均努谢尔数随着雷诺数的增大而增大,与加热功率无关;为了更好地表达微针肋槽道内的换热特性,考虑了槽肋比、流动雷诺数等影响,拟合了去离子水在微针肋槽道内的对流换热关系式。     

非均匀壁面棒束间流场结构的数值分析

本文采用CFD方法对棒束内的流动状况进行非稳态模拟,利用已知的实验结果对计算模型进行验证,详细分析了非均匀壁面粗糙度条件下雷诺数对冷却剂交混流动特性的影响。结果表明:非均匀壁面粗糙度对棒柬间速度场分布及交混系数有明显的影响。并且,当流动雷诺数提高时,棒束间的交混强度先增强然后减弱,存在一个最佳的流动雷诺数条件,在此雷诺数下,非均匀壁面粗糙度棒束间的湍流交混和相干涡结构最强烈。     

矩形微管内摩擦阻力特性的实验研究

以极性液体蒸馏水、无水乙醇及非极性液体R113作为实验工质,流过水力直径为231.91μm、250.88μm、297.14pm和210.89 pm,相应高宽比分别为0.90、0.70、0.90和0.42的由晶体生长方法得到的矩形紫铜微管,其相对粗糙度分别为1.47%、1.59%、1.48%和1.45%,测量其进出口压降与流量,从而获得摩擦阻力系数f与雷诺数Re的关系.实验结果表明:微管内流体的极性对微管流动阻力特性没有影响;同时实验结果显示对于粗糙度小于2%的矩形紫铜微管,其内壁面粗糙度对其流动阻力特性影响较小.当Re小于1600时,所有微管内的流动阻力特性与经典层流预测值几乎一致;而对于高宽比较小的矩形紫铜微管,当Re超过1600～1700时,微管的,值明显偏离经典层流预测值.     

高炉渣熔融液滴撞击壁面行为特性实验研究

针对高温熔渣粒化技术的开发,本文通过可视化实验研究了高炉渣熔融液滴撞击不锈钢壁面的动态行为特性。结果表明:随液滴雷诺数增大,撞击过程液滴形态演变模式依次由铺展-回缩转变为铺展-回缩破碎和铺展-破碎-凝固;增大壁面粗糙度可减弱与壁面换热,抑制液滴铺展;减小壁面粗糙度促进液滴发生破碎;液膜回缩过程普遍出现回卷现象,壁面倾角越大,液膜回卷和液滴滚动现象越显著,且液滴铺展面积越大,在壁面停留时间越长;减小液滴雷诺数、减小壁面粗糙度并采用垂直粒化仓壁面有利于壁面防黏结。     

微尺度下壁面粗糙度对面向导热影响研究

随着空间尺度的缩小,界面对导热的影响就会越来越明显。本文采用非平衡分子动力学模拟方法模拟了壁面的粗糙度对面向导热的影响,并给出微尺度下的粗糙度定义。在模拟中构造了不同的壁面粗糙度,得到了面向热导率随着壁面粗糙度增加而减小的结果。分析认为壁面的镜面反射率随着粗糙度增加而减小,而镜面反射率减小将导致热导率下降．     

冲击射流在凹坑壁面通道内的换热特性研究

采用热色液晶瞬态测温技术对航空发动机进气道支板的带凹坑壁面通道内表面开展冲击换热实验。研究了不同射流角度和射流雷诺数下通道内表面的换热特征。结果表明:沿流向在出气缝附近形成换热的高值区,在凹坑尾缘形成局部的高值区。凹坑壁面的换热要强于光滑壁面。随着射流雷诺数的增加,平均努塞尔数增大。当射流倾斜入射时,被冲击一侧换热较高,在驻点区域以及凹坑的尾缘换热最强,另一侧内壁面换热相对弱。射流角度30°时,被冲击面的换热最显著。在射流角度15°时,前缘附近的换热效果最强。     

微针肋内潜热型功能热流体换热特性研究

引入潜热型功能热流体替换现有传统工质冷却大功率激光器,实验研究了潜热型功能热流体与传统工质去离子水在高4 mm、宽2 mm、间距1 mm的微针肋内的层流流动换热特性。结果表明:在雷诺数Re为625~1125范围内,潜热型功能热流体均表现出比水更好的冷却性能及更低的壁面温度,且存在最佳的质量分数值;相同工况下,潜热型功能热流体平均努谢尔数Nu大于去离子水,平均努谢尔数Nu随着雷诺数Re的增加而增加。拟合了平均努谢尔数与流体雷诺数、普朗特数、质量分数的经验的关系式,最大偏差为16.9%,可以较好反映潜热型功能热流体的换热特性;潜热型功能热流体沿着流动长度的方向存在一个稳定的局部换热强化区,且强化换热存在最佳的长度。     

CaCO_3在不锈钢光管内结垢特性及其对传热的影响

本文研究了雷诺数Re=600~2600时,CaCO_3析晶污垢在316L不锈钢光管内结垢特性及其对传热的影响,实验结果表明污垢热阻在粗糙度诱导期和污垢生长期的变化规律及粗糙度诱导期随流速先减小后增大。采用称量法获得CaCO_3在不锈钢光管内的结垢质量,得出Re=600~2100时,污垢平均生长速率随雷诺数增加而增大。     

偏工况下壁面粗糙度对泵腔内流动规律的影响

本文将结合雷诺时均方程、RNG k-ε湍流模型和等效沙粒粗糙度模型,研究一离心泵泵腔内的流动规律与壁面粗糙度和运行工况的关系。研究表明:壁面粗糙度对离心泵外特性的影响存在一个峰值,此时绝对粗糙度的值为0.2mm;随着流量的增加,壁面粗糙度对叶轮前、后盖板所受扭矩的影响增加、对离心泵轴功率的影响减小。设计工况下,前泵腔中存在无量纲切向速度α值不变的核心流动区域。在核心流动区域内,随着粗糙度的增加,α值先减小,达到极小值后趋于稳定,稳定值为0.51。在前盖板附近,极小值往粗糙度较大的方向移动。小流量工况下,湍流核心区域消失,动、静壁面附近α值随流量的变化规律相反。大流量工况下,湍流核心区域减小,且更加靠近静壁面。     

矩形微通道中流阻特性的实验研究

以工程上常用的66%的乙二醇水溶液作为工质,对几何特性相似而高宽比不同的4种纯铝矩形微通道内的流动特性进行了实验研究,得到了微通道冷板基础性的设计数据。实验测量了Reynolds数在50~500之间的流动阻力系数。实验结果表明:通道高度H与宽度W之比对微通道流阻特性有显著的影响;当Re数小于100时,在实验误差内,流动阻力系数的值近似等于经典理论计算值;随着Re数的增大和高宽比的变化,f的值远大于理论值,这可能是由微通道内部壁面粗糙度效应所导致的。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.