两性孪联表面活性剂的合成及溶液性质

用C10～C16脂肪醇与2-氯-2-氧-1,3,2-二氧磷杂环戊烷低温反应生成环状磷酸酯的中间产物,再用N,N-二甲基十二胺在亲核溶剂中65℃下开环反应合成了4种含N 和磷酸根阴离子的两性孪联表面活性剂C10-C12、C12-C12、C14-C12和C16-C12,其质量收率分别为32%、54%、18%和28%。产物的结构通过1HNMR和元素组成分析,表明两性离子表面活性剂C、H、O、N的分析值与理论计算值偏差不超过0.3%。四种表面活性剂的临界胶束浓度(cmc)在0.0072~0.0125mmol/L之间,临界胶束浓度时表面张力(γcmc)依次为23.90、25.61、27.68和36.08mN/m。其中,C10-C12、C12-C12和C14-C12有较好的界面活性,加入盐可以使表面活性剂与烷烃间的界面张力下降,但下降程度有限,不能达到超低界面张力(10-3mN/m)。     

CMC系列高分子表面活性剂与原油 超低界面张力形成机理的研究

采用动态激光光散射及环境扫描电镜研究了羧甲基纤维素系列高分子表面活性剂与大庆原油形成超低界面张力的机理.结果表明,CMC系列高分子表面活性剂具有与低分子量表面活性剂相比拟的表/界面活性,其水溶液的表面张力可达28～35mN/m,界面张力达到10     

CMC系列高分子表面活性剂与原油超低界面张力形成机理的研究

采用动态激光光散射及环境扫描电镜研究了羧甲基纤维素系列高分子表面活性剂与大庆原油形成超低界面张力的机理.结果表明,CMC系列高分子表面活性剂具有与低分子量表面活性剂相比拟的表/界面活性,其水溶液的表面张力可达2835mN/m,界面张力达到10^-110mN/m.碱的加入可显著降低高分子表面活性剂与原油的界面张力,在适当条件下界面张力达到超低值(10^-3mN/m),可望作为三次采油的驱油剂.等效烷烃模型研究表明,用碱与原油酸性组分的作用来解释碱能使界面张力下降至超低值的传统观点是不完善的,加入碱能使高分子表面活性剂胶束解缔,胶束数量增多,胶束粒径减小,单分子自由链增加,有利于高分子表面活性剂向界面迁移和排布,这是高分子表面活性剂和碱复配体系与原油界面张力下降至超低值的主要原因.     

表面活性剂的协同作用在甲维盐微乳剂中的应用

通过测定不同类型的单一及复配型表面活性剂水溶液的临界胶束浓度和表面张力,研究了它对W(甲维盐)=1%微乳剂的性能影响。膦酸酯类阴离子表面活性剂A的临界胶束浓度为1.79×10-4mol/L,表面张力为28.90mN/m;苯乙烯基酚聚氧乙烯聚氧丙烯醚嵌段型非离子表面活性剂B(EPE型)的临界胶束浓度为1.91×10-4mol/L,表面张力为20.70mN/m;按m(A)∶m(B)=2∶3形成的复配型表面活性剂2#的水溶液的临界胶束浓度为9.30×10-5mol/L,表面张力为25.66mN/m。当W(2#)=10%时,配制W(甲维盐)=1%的微乳剂物理稳定性最佳,各项指标均合格。对甘蓝小菜蛾幼虫的田间药效的试验,结果表明该药剂具有较强的杀虫作用和较长的持效期,具有较好的推广应用前景。     

Gemini阴离子表面活性剂水溶液的界面活性

Gemini阴离子表面活性剂水溶液的界面活性;Gemini阴离子表面活性剂;表面张力;CMC;C20;界面张力     

新型磺基甜菜碱/聚丙烯酰胺体系表面及界面性能

采用自制的新型磺基甜菜碱两性表面活性剂与相对分子质量2500万的聚丙烯酰胺进行复配,考察了不同温度和矿化度条件下,聚合物对复配溶液表面、界面性能的影响。 采用滴体积法测定了溶液的表面张力,结果表明,加入聚合物使溶液的临界胶束浓度增大,且复配溶液的表面张力大于单独表面活性剂溶液的表面张力。 当聚合物浓度一定,增大溶液矿化度时,体系表面张力增大。 用旋滴型界面张力仪测定了溶液的界面张力,结果表明,增大聚合物浓度,油水界面张力增大,增大溶液矿化度,油水界面张力有所升高。 聚合物质量浓度为1.5 g/L,表面活性剂质量浓度为0.3 g/L时,可使胜利油田孤岛原油和孤东原油的油水界面张力达到超低数量级（10-3 mN/m）。 用分水时间法测定了溶液的乳化性能,结果表明,聚合物浓度增大,分水时间延长,并考察了75、85和95 ℃条件下体系的乳化性能,温度越高,分水时间越短。     

新型阳离子表面活性剂的合成及表面活性研究

以α-长链烷基吡啶和烯丙基氯为原料合成了吡啶盐型阳离子表面活性剂———N-烯丙基-2-烷基氯化吡啶嗡盐(GS-n),研究了其表面性能,结果表明,GS具有较好的表面活性,其中N-烯丙基-2-十六烷基氯化吡啶嗡盐(GS-16)具有最低的临界胶团浓度(CMC,0.527 mmol.L-1);随着α-烷基链的增长,GS的CMC显著降低,表面张力(γcm c)则先降后升;GS-12的γcm c为27.1 mN.m-1。     

以油酸为原料的新型生物基支链十七烷基苯磺酸钠的合成及性质

生物基表面活性剂由于其可再生资源和优异的表面/界面性质吸引了越来越多的关注。本文以可再生的油酸为原料,通过四步反应,制备了新型生物基支链表面活性剂,并评价了其表/界面性质、润湿性和生物降解性能。该新型生物基支链表面活性剂为4-（1-十七烷基）苯磺酸钠（9ΦC17S）,依次经过烷基化反应、脱羧反应、磺化反应和中和反应而制得。其化学结构已通过电喷雾质谱、红外光谱和核磁共振波谱得以确认。4-（1-十七烷基）苯磺酸钠展现出良好的表/界面张力,临界胶束浓度（CMC）为317.5 mg·L^-1,CMC处的表面张力为32.54 mN·m^-1,当水溶液中碳酸钠浓度为8.48×10⁴ mg·L^-1、4-（1-十七烷基）苯磺酸钠浓度为8.36×10⁴ mg·L^-1时,油水的界面张力约为10^-2 mN·m^-1。此外,4-（1-十七烷基）苯磺酸钠在生物降解性和润湿性方面也显示出了良好的性能,最终生物降解评分为2.99,0.500 g·L^-1 9ΦC17S溶液的气液固接触角为63.08°。该新型生物基表面活性剂丰富了以可再生资源为原料的生物基表面活性剂的结构多样性。     

支链醇对Gemini表面活性剂表面活性和胶束化行为的影响

Gemini表面活性剂是一类高效的新型表面活性剂,而醇是工业界和日化领域最常采用的表面活性剂助剂,因此研究不同结构的醇对Gemini表面活性剂表面活性和胶束化行为的影响规律和机理对于促进Gemini表面活性剂的发展和实际应用具有重要意义.利用表面张力、电导、等温滴定微量热,低温透射电镜和核磁共振研究了直链醇1-戊醇和具有相同主链的支链醇2-己醇与3-庚醇对具有不同长度连接基团阳离子季铵盐型Gemini表面活性剂C₁₂C_SC₁₂Br₂ （S=2,4,6,8,10,12）的表面活性和胶束化行为的影响,结果发现,支链醇能够显著影响表面活性剂在气/液界面的排布,使得C₂₀ （使溶剂的表面张力降低20 mN/m所需的表面活性剂浓度）和γ_CMC （CMC时表面张力值）随醇支化度的增加而显著降低,而支链醇对表面活性剂在溶液中的临界胶束浓度以及胶束的尺寸和形貌均没有明显影响,同时这些醇对Gemini表面活性剂的影响与连接基团的长度相关.阐述了上述结果产生的机理,将有助于指导如何选择合适结构的醇助剂去调控Gemini表面活性剂的表面和溶液性质.     

基于丙二酰胺的不对称双子表面活性剂的合成及其乳化性能

将二(3-二甲氨基丙基)丙二酰胺分别与溴代十六烷和溴代十四烷反应,生成的季铵盐化产物经丙酮-乙腈重结晶,得到含丙二酰胺基的不对称阳离子双子(Gemini)表面活性剂(命名为16-9-14),总收率为45.9%(以溴代十六烷计);利用红外光谱和核磁共振谱表征了合成产物的结构,采用电导法测定了其临界胶束浓度(CMC),采用滴体积法测定了其临界张力(γCMC),进而初步探讨了其发泡沫性能和乳化性能.结果表明,合成的Gemini表面活性剂的CMC为1.57×10-4 mol/L,γCMC为38.45mN/m;其发泡性能和乳化性能优于相应的单子表面活性剂.     

以全氟丁基为基础的具有高表面活性的氟表面活性剂

氟表面活性剂的环境和生物降解问题是最近的热点, 特别是全氟长链(≥C8)氟表面活性剂的应用限制乃至禁用已成为必然趋势. 本文合成了一种以短链的全氟丁基为基础的阳离子氟表面活性剂, N-[3-(二甲基胺基)丙基]全氟丁基磺酰胺盐酸盐(C4F9SO2NH(CH2)3NH(CH3)+2Cl-, 简称为PFB-MC). 该表面活性剂适用于强酸性环境, 具有极高的表面活性, 其溶液最低表面张力(19.80 mN·m-1)和通常的氟表面活性剂相当. 通过表面张力方法得到了固定pH(pH=2.6-2.7)情况下PFB-MC的表面张力-浓度对数(γ-lgc)曲线, 以及该pH下外加盐([NaCl]=0.1 mol·L-1)对表面张力的影响; 并进一步研究了pH对PFB-MC在其临界胶束浓度(cmc)前后的表面张力的影响.     

Adsorption Properties of Hydrocarbon and Fluorocarbon Surfactants Ternary Mixture at the Water-Air Interface

Measurements were made of the surface tension of the aqueous solutions of p-(1,1,3,3-tetramethylbutyl) phenoxypoly(ethylene glycols) having 10 oxyethylene groups in the molecule (Triton X-100, TX100) and cetyltrimethylammonium bromide (CTAB) with Zonyl FSN-100 (FC6EO14, FC1) as well as with Zonyl FSO-100 (FC5EO10, FC2) ternary mixtures. The obtained results were compared to those provided by the Fainerman and Miller equation and to the values of the solution surface tension calculated, based on the contribution of a particular surfactant in the mixture to the reduction of water surface tension. The changes of the aqueous solution ternary surfactants mixture surface tension at the constant concentration of TX100 and CTAB mixture at which the water surface tension was reduced to 60 and 50 mN/m as a function of fluorocarbon surfactant concentration, were considered with regard to the composition of the mixed monolayer at the water-air interface. Next, this composition was applied for the calculation of the concentration of the particular surfactants in the monolayer using the Frumkin equation. On the other hand, the Gibbs surface excess concentration was determined only for the fluorocarbon surfactants. The tendency of the particular surfactants to adsorb at the water-air interface was discussed, based on the Gibbs standard free energy of adsorption which was determined using different methods. This energy was also deduced, based on the surfactant tail surface tension and tail-water interface tension.     

Gemini表面活性剂烷烃尾链在吸附和聚集过程中的疏水协同效应(英文)

以表面张力法测定了系列Gemini表面活性剂m-6-m以及对应单体表面活性剂CmTABr的临界胶束浓度(cmc)和降低水表面张力20mN·m-1需要的浓度(pC20).比较这些参数表明m-6-m胶束化和在界面吸附的能力均强于CmTABr,这被归结为Gemini表面活性剂烷烃尾链间的疏水协同效应.与不对称Gemini表面活性剂12-6-m比较,对称的Gemini结构更有利于表面活性剂的聚集和吸附.     

m-6-m型Gemini双季铵盐表面活性剂与DNA的相互作用

合成了5种m-6-m型Gemini双季铵盐表面活性剂,在对产物结构和表面活性进行分析的基础上,分别采用紫外分光光度法和荧光分光光度法考察了m-6-m型Gemini双季铵盐表面活性剂与DNA的相互作用.结果表明,m-6-m型Gemini表面活性剂的CMC随烷基疏水链的增长呈逐渐下降趋势.几种表面活性剂均没有使DNA的紫外吸收峰发生红移或蓝移现象,说明复合物无嵌插作用或氢键形成,表面活性剂与DNA作用后的吸光度随表面活性剂浓度的增大而增强,当表面活性剂的浓度相同时,吸光度随疏水链的增大而逐渐减弱.Gemini表面活性剂浓度增大导致荧光强度降低,表面活性剂与DNA作用时的猝灭为静态猝灭,随着疏水链长度的增长,荧光猝灭常数降低,表面活性剂与DNA之间的作用力减弱.     

新型腰果酚双子表面活性剂的合成及表面活性

以天然生物质腰果酚、1,3-二溴丙烷及氯磺酸为原料,通过醚化、磺化及中和三步反应合成了一类新型的腰果酚基磺酸盐双子(Gemini)表面活性剂.采用傅立叶转换红外光谱仪和核磁共振谱仪表征了产物的结构;采用滴体积法测定了腰果酚Gemini表面活性剂的表面张力,研究了水溶液的表面性质,并与相应的单基腰果酚基磺酸盐表面活性剂进行了对比.结果表明:腰果酚Gemini表面活性剂水溶液的临界胶束浓度(cmc)为6.20×10-2 mmol.L-1,远小于相应的单基腰果酚表面活性剂水溶液的cmc(8.40mmol.L-1);其临界表面张力γcmc为36.92mN.m-1,与单基腰果酚表面活性剂水溶液的相近(γcmc为38.41mN.m-1).与此同时,腰果酚Gemini表面活性剂水溶液的最小分子截面积Amin为0.27nm2,比相应的单基表面活性剂水溶液的小得多.     

Interfacial activity of a novel family of polymeric surfactants

A novel series of polymeric surfactants based on carboxy methyl cellulose and alkyl poly(etheroxy) acrylate were synthesized by ultrasonic irradiation. These polymeric surfactants have exhibit excellent surface activity due to their unique structure. The influences of salt, alcohol and alkali on the interfacial activity of these polymeric surfactants were studied by interfacial tensiometery, dynamic laser scattering (DLS), UV spectroscope and environmental scanning electrical microscope (ESEM). The surface tension and interfacial tension (IFT) properties change little with NaCl added. The formed micelles shrink, their size becomes smaller. Alcohols cause the IFT to decrease a little because a small amount of free chains present in solution. Under the influence of added alkali, the IFT of the polymeric surfactants, in aqueous solution, decreases so much that sometimes it is less than 10⁻² mN/m. Using data from the equivalent alkane scan, one cannot draw the conclusion that the action of alkali with the acidic components in crude oil leads to the ultra-low IFT. The analyses by UV, DLS and ESEM show that the micelles formed by polymeric surfactants could be disaggregated or destroyed sharply by the action of alkali. So the size of micelles decreases greatly and the number of free chains increases. That more polymeric surfactants molecules move to the interface of oil/water and rearrange at the interface of oil/water is believed to be the main reason of the ultra-low IFT (10⁻³ mN/m) that is obtained.     

Ultralow interfacial tension for enhanced oil recovery at very low surfactant concentrations

The interfacial tension (IFT) between alkanes and several individual surfactants and their mixtures has been investigated, using three kinds of alkyl hydrocarbons: decane, dodecane, and tetradecane. For individual and mixed surfactant systems, critical micelle concentrations and areas per molecule at the hydrocarbon-aqueous solution interface were calculated; for the mixed surfactant systems, betasigma(LL), the molecular interaction parameter at the hydrocarbon-aqueous solution interface, and beta(M), the molecular interaction parameter in mixed micelle formation, were calculated. It was found that IFT in the 10(-3) mN/m (ultralow) range can be obtained at surfactant concentrations below 0.05 wt % and even at concentrations below 0.01 wt %, when mixtures of certain surfactants are used at the proper ratio. Surfactants with branched-chain alkyl groups show a much better IFT reduction effectiveness than those with straight-chain alkyl groups. Contrary to what has been observed at the air-aqueous solution surface, mixtures of two homologues with two hydrophobic groups show significant molecular interactions, with both betasigma(LL) and beta(M) having negative values in the 4-5 range in some cases, with the betasigma(LL) value more negative than beta(M). The relationship between micellar shape and ultralow IFT was investigated by calculating the critical packing parameter of the surfactants. It was found that ultralow IFT between the surfactant mixtures and the three hydrocarbons investigated could reach ultralow (<10(-2) mN/m) values when the critical packing parameter is very close to 1.     

Gemini surfactants at the air/water interface: a fully atomistic molecular dynamics study

Gemini surfactants typically consist of two single-chain surfactants chemically linked by a spacer molecule. We report herein the results of fully atomistic molecular dynamics (MD) simulations of a series of Gemini surfactants: CsH2s-alpha,omega-bis(C12H25N+(CH3)2Cl-), at the air/water interface with s = 3, 4, 6, 12, 14, and 16, at values of the initial surface area per surfactant AS = 70 A2, 77 A2, 95 A2, 151 A2, 133 A2, and 103 A2, respectively. The AS values employed were obtained from surface tension and neutron reflection experiments at the respective cmc of each surfactant. The Gemini surfactant corresponding to s = 3 was also simulated at AS = 105 A2, which is the experimentally derived value of surface area per surfactant at 1/10th of cmc. Only the surfactants with s = 12 and 14 and the surfactant with s = 3 at AS = 105 A2 gave a stable monolayer at the air/water interface. In other cases, we observe movement of some surfactant molecules from the air/water interface into the aqueous phase, resulting in a stable primary monolayer of surfactants at the air/water interface and a small concentration of surfactant molecules below it. The latter form aggregates, with their hydrophobic chains in the core. The density profiles along the normal to the interface are compared with the ones obtained from neutron reflection experiments. The MD simulations confirm the bending of the spacer toward the hydrophobic chains as the spacer length is increased and the spacer becomes more hydrophobic. The simulations have helped to shed light on the low-resolution picture which emerges from experimental analyses.     

Micellization and mixed micellization of cationic gemini (dimeric) surfactants and cationic conventional (monomeric) surfactants: Conductometric,dye solubilization,and surface tension studies

In the present study, we have investigated the self-association, mixed micellization, and thermodynamic studies of a cationic gemini (dimeric) surfactant, hexanediyl-1,6-bis(dimethylcetylammonium bromide (16-6-16)) and a cationic conventional (monomeric) surfactant, cetyltrimethylammonium bromide (CTAB). The critical micelle concentration (CMC) of pure (16-6-16 and CTAB) and mixed (16-6-16+CTAB) surfactants was measured by electrical conductivity, dye solubilization, and surface tension measurements. The surface properties (viz., C₂₀ (the surfactant concentration required to reduce the surface tension by 20 mN/m), Π_CMC (the surface pressure at the CMC), Γ_max (maximum surface excess concentration at the air/water interface), A_min (the minimum area per surfactant molecule at the air/water interface), etc.) of micellar (16-6-16 or CTAB) and mixed micellar (16-6-16+CTAB) surfactant systems were evaluated. The thermodynamic parameters of the micellar (16-6-16 and CTAB) and mixed micellar (16-6-16+CTAB) surfactant systems were also evaluated.