基于光电反馈环单元时钟提取与解复用的160 Gb/s OTDM 信号100 km传输

提出了一种能够同时对高速光时分复用技术信号解复用与时钟提取的光电反馈环单元.在接收端,采用光电反馈环单元,信号单次通过即可同时完成160 Gb/s到10 Gb/s的解复用与时钟提取：两级电吸收调制器级联工作方式缩减了采样窗口宽度,满足了解复用小于6.25 ps超窄采样窗口的要求|而闭合环路的锁相同步工作方式,使所提取的时钟信号抖动（Jitter RMS）由2.4 ps降至450 fs.基于该结构,实验上成功实现了无误码的100 km 160 Gb/s光时分复用技术传输及传输后无误码地解复用与时钟提取,功率代价小于3 dB.     

基于光电反馈环单元时钟提取与解复用的160Gb/s OTDM信号100km传输

提出了一种能够同时对高速光时分复用技术信号解复用与时钟提取的光电反馈环单元.在接收端,采用光电反馈环单元,信号单次通过即可同时完成160Gb/s到10Gb/s的解复用与时钟提取:两级电吸收调制器级联工作方式缩减了采样窗口宽度,满足了解复用小于6.25ps超窄采样窗口的要求;而闭合环路的锁相同步工作方式,使所提取的时钟信号抖动(JitterRMS)由2.4ps降至450fs.基于该结构,实验上成功实现了无误码的100km160Gb/s光时分复用技术传输及传输后无误码地解复用与时钟提取,功率代价小于3dB.     

A Simple Loop for Simultaneous OTDM Demultiplexing and Clock Recovery

A simple and stable loop consisting of a pair of concatenated electroabsorption modulators （EAMs） and 10 GHz clock recovery module is presented and demonstrated experimentally for simultaneous demultiplexing and clock recovery for OTDM networks. The 10 Gb/s demultiplexed signal and 10 GHz recovered clock are successfully implemented from 80 Gbit/s and 160 Gbit/s OTDM signals utilizing the loop. The loop based on EAM-PLL can provide excellent tolerance range （〉 5 dB） of the OSCR of the source laser, and the recovered clock signal exhibits low rms jitter over a dynamic input optical power range of 15 dB.     

利用非线性光纤环镜160Gb/s到10Gb/s解时分复用

研究了160 Gb/s光时分复用(OTDM)系统的解复用技术.针对160 Gb/s速率的特点,对高非线性光纤(HNLF)的光纤环镜(NOLM)特性及解复用进行了数值仿真.计算了低信号光时间抖动下解复用误码特性对时钟与信号的走离及时钟功率的依赖关系.计算了三种走离值消光比随时钟功率增加的变化趋势并给出:存在一个能获得最大的解复用窗口消光比、并能降低相邻信道串扰的合适的时钟功率范围.利用自制的基于电吸收调制器和压缩技术的超短光脉冲源建立了160 Gb/s OTDM实验系统,测量了不同信号光功率下NOLM的消光比,它基本不随信号增大而变化,在信号功率为7.3 dBm时仍大于23 dB.利用上述装置实现了无误码的160 Gb/s到10 Gb/s全光解复用.     

Tone Modulation in a Passive OTDM Multiplexer for Clock Recovery from a 160 Gbit/s OTDM Signal

Tone modulation in a passive OTDM multiplexer for clock recovery from a 160-Gbit/s OTDM signal by using a base-rate receiver is demonstrated. We performed synchronous demultiplexing in back-to-back arrangement and optical sampling after 320-km transmission.     

利用光锁相环路实现40 Gb/s时钟恢复

提出并建立了一种新型的基于光纤四波混频效应和压控光脉冲源的光锁相环路(OPLL),用于光时分复用系统(OTDM)中的时钟恢复过程。从理论上分析了其工作原理,及各模块结构和功能。利用高非线性光纤中的四波混频效应实现全光鉴相器,有效缩短了光纤长度,减小了光纤色散引起的脉冲走离,鉴相器消光比超过30 dB。采用再生锁模光纤激光器实现压控光脉冲源,在保证脉冲质量的前提下,重复频率调节范围达到380 kHz。在40 Gb/s时钟恢复实验中,获得脉宽为7.2 ps、接近变换极限的时钟脉冲,时间抖动(RMS)为152 fs,超模抑制比大于60 dB。实验证明,输入信号幅度波动和码型效应对环路影响很小。     

时分复用信号中的全光时钟提取实验

利用非均匀复用后的时分复用 (OTDM)信号 ,从 4× 2 .5GHz的时分复用光脉冲信号中直接提取出复用前的2 5GHz分路时钟信号。此技术可用于高速率时分复用光纤通信系统的解复用中的时钟提取。     

Directly Modulated 10 Gb/s Signal Transmission over 320 km of Negative Dispersion Fiber for Regional Metro Network

We demonstrate the transmission of directly modulated 10-Gb/s WDM signals over 320 km of negative dispersion fiber (dispersion:-2.5 ps/km/nm @1550 nm) without dispersion compensation. The results indicate that a regional metro WDM network could be implemented cost-effectively by using the proposed negative dispersion fiber and direct modulated lasers.     

双用户2.5 Gb/s 100 km光码分多址传输实验

稳定性高、低成本的窄脉冲光源、高性能编解码器和具有旁瓣/噪声抑制功能的接收机是光码分多址系统实用化的3个关键模块.实验中利用增益开关脉冲光源和63 chip等效相移超结构布拉格光纤光栅相位编解码器的半边带应用,判决门限调整与宽带判决相结合的接收机实现了双用户、2.5 Gb/s 100 km传输.实验中测量了误码率与判决时刻和判决门限的关系曲线,系统在10 ps的判决时刻容限内和17%的幅度判决容限内实现了无误码传输.     

Realizing 20 Gbit/s OTDM Transmission over 50 km True-wave Fiber with Dispersion Compensation

20 Gbit/s OTDM transmission over 50 km true-wave fiber with dispersion compensation was realized for the first time in China. The power penalty is smaller than 8 dB. The following technology problems were solved: the generation and the compression of ultra-short optical pulse; low bits to high bits multiplexer; high bits to low bits demulitplexer; the clock extraction from high speed system, dispersion compensation.     

Signal Demultiplexing from an 8.2×2.5 Gb/s OTDM Data Stream Using NOLM: Demonstration and Bit Error Rate Measurement

It is presented the experiment of all-optical demultiplexing of one 2.5 Gb/s channel from an 8×2.5 Gb/s OTDM data stream using nonlinear optical loop morror with 3 km dispersion shifted fiber. Bit error rate (BER) of the demultiplexed channel is measured. A BER of 10-11 is achieved and the power penalty is only 1.4 dB when BER is 10-9.     

Realizing 20 Gbits OTDM Transmission over 50km Truewave Fiber with Dispersion Compensation

Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｔｈｅｒｅａｒｅｔｗｏｍｅｔｈｏｄｓｔｏｅｎｈａｎｃｅｔｈｅｃａｐａｃｉｔｙｏｆｔｈｅｔｒａｎｓｍｉｓｓｉｏｎｓｙｓｔｅｍ：ｏｐｔｉｃａｌｔｉｍｅｄｉｖｉｓｉｏｎｍｕｌｔｉｐｌｅｘｉｎｇ（ＯＴＤＭ）ａｎｄｏｐｔｉｃａｌｗａｖｅｌｅｎｇｔｈｄｉｖｉｓｉｏｎｍｕｌｔｉｐｌｅｘｉｎｇ（ＷＤＭ）．ＯＴＤＭｉｓｂｅｉｎｇｗｉｄｅｌｙｒｅｓｅａｒｃｈｅｄｂｅｃａｕｓｅｏｆｓｏｍｅｖｉｒｔｕｅｓｉｎｏｐｔｉｃａｌｎｅｔｗｏｒｋｓ［１～４］．ＯＴＤＭｗｉｔｈｔｈｅｓｉｎｇｌｅｃｈａｎ…     

面向LOFAR应用的160Gbit/s OTDM试验平台

报告了一个用于低频射频天线网络LOFAR的160 Gbit/s 演示平台.文章介绍了LOFAR网络结构以及用于LOFAR长臂的OTDM/WDM系统结构,回顾并探讨了用于实现160 Gbit/s系统的关键技术,并介绍了实验室中实现该160 Gbit/s OTDM/WDM演示平台所采用的技术方案。出于经济性考虑,所有的关键系统功能都采用自己搭建方案.     

Demonstration of single channel 160-Gb/s OTDM 100-km transmission system

A 16 × 10-Gb/s optical time-division-multiplexing (OTDM) 100-km transmission system with home-made multiplexer is demonstrated experimentally. A demultiplexer based on two cascaded electro-absorption modulator (EAM) and a clock recovery unit form a feedback loop. Error-free demultiplexing from 160-Gb/s to 10-Gb/s after over 100-km transmission is achieved. The power penalty is about 3.5 dB with the bit error rate of 10⁻⁹.     

Transmission of 2.5 Gb/s WDM Channels Spaced at 5 GHz over 480 km of Single-Mode Fiber

We demonstrate the transmission of 2.5-Gb/s WDM signals spaced at 5 GHz over 480 km of single-mode fiber. The results indicate that it should be possible to transmit more than one thousand 2.5-Gb/s channels spaced at 5 GHz over long distance.     

Transmission of 20 Gb/s PAM-4 signal over 20 km optical fiber using a directly modulated tunable DBR laser

We report 20 Gb/s transmission of four-level pulse amplitude modulation(PAM) signal using a directly modulated tunable distributed Bragg reflector(DBR) laser. Transmission distance over 20 km was achieved without using optical amplifiers and optical dispersion compensation modules. A wavelength tuning range of 11.5 nm and a 3 dB bandwidth greater than 10 GHz over the entire wavelength tuning range were obtained.     

40Gb/s光纤传输单边带归零信号的产生和性能分析

对光的单边带归零信号（SSBRZ）的一种产生方式进行了推导.通过合理设置调制器的偏置电压，使产生的SSBRZ信号的一个边带得到更有效的抑制，而且没有引起光脉冲的变形.对其在普通单模光纤（SMF）40Gb/s传输系统中的传输进行了仿真，并和归零（RZ）信号、载波抑制的RZ（CSRZ）信号的性能相比较，结果表明：在色散完全补偿的单信道传输系统中，SSBRZ的抗非线性能力比RZ、CSRZ强.     

Simultaneous clock recovery and demultiplexing of a 320 Gb/s OTDM system using an optoelectronic oscillator based on cascaded MZM and PolM

An improved optoelectronic oscillator scheme for an optical time division multiplexing(OTDM) system based on cascaded Mach-Zehnder modulator(MZM) and polarization modulator(PolM) is experimentally investigated.The system can simultaneously realize clock recovery and demultiplexing.With the MZM working at peak point to generate return-to-zero-33 optical pulses and the PolM working as an equivalent intensity modulator,a high-quality clock signal with 35-fs timing jitter is extracted from the 160-GBaud OTDM-differential quaternary phase-shift keying signal.Narrow short optical switch gates(4 ps) are also generated to demultiplex 160-GBaud signals to 40-GBaud signals.Error-free performance is achieved with 2.4-dB power penalty in the worst case.     

100Gb/s归零码信号的2R再生

本文提出了基于半导体光放大器(SOA)中的瞬态交叉相位调制(T-XPM)效应与交叉增益压缩(XGC)效应的全光2R再生方法, 同时研究了SOA中的T-XPM效应获得反逻辑码信号以及XGC 效应光开关门的特性, 实现了100 Gb/s归零码(RZ)信号的2R再生, 接收机灵敏度提高了1.7-2 dB; 对该方案中的反逻辑码对于再生效果的影响进行了量化研究, 并在C波段范围内研究了该再生方案的再生效果, 实现了覆盖1535-1555 nm的全光2R再生.     

A Stable Ultrashort Pulse Generator Based on EAM and Well-Designed Compressor for Applications in 160 Gbit/s OTDM Networks

A stable 10 GHz ultrashort pulse generator consisted of an electroabsorption modulator （EAM） and a welldesigned fibre-based pulse compressor is proposed and demonstrated experimentally. The obtained short pulse has high extinction ratio, no pedestal, low timing jitter, and FWHM of only 2.4ps. The excellent performance of multiplexing from 10 GHz to 160 GHz confirms the potential of the generator for applications in 160 Gbit/s optical time-division-multiplexing （OTDM） systems.