Simultaneous determination of paraquat and diquat in serum using capillary electrophoresis.

The use of capillary electrophoresis for simultaneous separation and detection of the two bipyridylium herbicides, paraquat and diquat, was investigated. Both herbicides were extracted from fortified sera with disposable ODS-silica cartridges. Separation was carried out using a capillary tube (50 microns i.d., 750 mm) of fused silica containing 10 mM glycine-HCl buffer (pH 3.0), 40 mM NaCl and 20% methanol as the carrier. Paraquat and diquat were completely separated in 10 min at an applied potential of 20 kV. On-column UV monitoring allowed detection of both herbicides simultaneously. The assay sensitivity was 0.05 micrograms/mL (signal-to-noise ratio, 2:1), which probably increases with increase in the sample volume of serum. Analytical recovery of both herbicides added to serum was about 97% at concentrations of 0.5-2.0 micrograms/mL.     

Sample stacking with matrix removal for the determination of paraquat, diquat and difenzoquat in water by capillary electrophoresis

Conditions for the simultaneous determination of paraquat, diquat and difenzoquat by capillary zone electrophoresis using a stacking technique in a chemically modified capillary have been established. To apply the stacking method with sample matrix removal for the analysis of cations, an anodic electroosmotic flow is mandatory. For quats, 50 mM acetic acid-ammonium acetate (pH 4.0) with 5% (v/v) methanol as electrophoretic buffer and the addition of 0.8 mM cetyltrimethylammonium bromide as wall capillary organic modifier was proposed. Field polarity reversal time was optimised for several sample matrices. Detection was carried out at 220 and 255 nm. Detection limits, based on a signal-to-noise ratio of 3:1, were lower than 15 microg l(-1) for standards in Milli-Q water and two to ten times higher for drinking water samples. Run-to-run and day-to-day reproducibility have been established. The method was successfully applied to the determination of the three herbicides in spiked drinking water.     

毛细管电泳法对南方水牛奶乳清蛋白的分离和定量分析

利用毛细管区带电泳对广东省水牛乳乳清蛋白成分进行了分离和定量分析研究.采用1.2%的十四水合硼酸钠电泳缓冲液,对水牛奶乳清蛋白的四种主要组分α-乳白蛋白(α-La)、β-乳球蛋白(β-Lg)、牛血清白蛋白(BSA)、免疫球蛋白(IgG)进行了很好的分离,其迁移时间和峰面积的RSD分别小于1.5%和0.5%,加标回收率范围91%～102%.建立了基于毛细管区带电泳的分析方法,对牛乳及其乳制品中的乳清蛋白进行了快速分离和定量分析.     

Determination of ethyl sulfate in human serum and urine by capillary zone electrophoresis

The use of capillary zone electrophoresis (CZE) with indirect absorbance detection for the analysis of ethyl sulfate (EtS) in serum and urine was investigated. EtS is a direct metabolite of ethanol employed as marker for recent alcohol consumption. Fused-silica capillaries of 60 cm total length were either coated with cetyltrimethylammonium bromide (CTAB, 50 microm I.D. capillary) or poly(diallyldimethylammonium chloride) (PDADMAC, 100 microm I.D. capillary) to allow CZE analyses to be performed with reversed polarity. At pH 2.2 with a maleic acid/phthalic acid background electrolyte, both approaches provided reliable EtS serum levels down to 0.2 mg L(-1) (1.6 microM) for the analysis of solid-phase extracts that were prepared after chloride precipitation. Analysis of urines diluted to a conductivity of 5 S m(-1) and analyzed in the two capillary formats resulted in limits of quantification (LOQs) of 2 and 1 mg L(-1), respectively. With urines adjusted to 10 S m(-1) via dilution or condensation, an LOQ of 0.6 mg L(-1) (4.8 microM) was obtained in the CTAB coated capillary whereas in the PDADMAC-coated capillary of equal length not all matrix components were resolved from EtS. The developed assays are robust and suitable to monitor EtS in samples of individuals who consumed as little as one standard drink of an alcoholic beverage containing about 14 g of ethanol.     

Separation and quantification of viral double-stranded RNA fragments by capillary electrophoresis in hydroxyethylcellulose polymer solutions

Capillary electrophoresis (CE) is an analytical technique widely utilized to resolve complex mixtures of nucleic acids. CE uses a variety of polymers in solution that act as a molecular sieve to separate nucleic acid fragments according to size. It has been shown previously that purified dsDNA can be resolved efficiently by solutions of hydroxyethylcellulose (HEC) polymer, providing a rapid and high resolution method of separation. We have applied this separation technique to viral double-stranded (ds) RNA segments derived from rotavirus process samples. HEC polymers of various molecular masses and concentrations were identified and compared for their ability to separate dsRNA based on the extent of expected polymer network formation. The HEC polymer exhibiting the most desirable separation characteristics was then used for subsequent optimization of various method parameters, such as, injection time, electric field strength, dye concentration and capillary equilibration. The optimized method was then applied to the quantification of genome concentration based on a representative segment of the rotavirus genome. This study demonstrated that purified viral dsRNA material of known concentration could be used to generate an external standard curve relating concentration to peak area. This standard curve was used to determine the concentration of unknown samples by interpolation. This novel RNA quantification assay is likely to be applicable to other types of virus, including those containing dsDNA.     

Separation of siderophores by capillary electrophoresis

Capillary electrophoresis (CE) was applied as a fast method of siderophore separation. Siderophores are iron binding and regulating cell products, which facilitate iron transport into cells. A fast and efficient method of siderophore analysis is important for better understanding of the iron pathways in a sea environment or marine organisms. The best results of CE analysis were obtained using free zone CE in 25 mM phosphate buffer at basic pH using a constant voltage of 20 kV. Under these conditions it was possible to detect the presence of siderophores in seawater.     

Separation of bacteria by capillary electrophoresis

Differences in the surface charges of bacteria can be exploited for their separation by capillary electrophoresis. Because of their low electrophoretic mobility, the separation is not always easy to perform, especially in the presence of the electroosmotic flow. Elimination of electroosmotic flow by capillary wall modification with γ‐(trimethoxysilyl)propyl methacrylate followed by acrylamide bonding permits separation over a distance of 8.5 cm.     

离子色谱-三重四极杆质谱法同时测定血浆和尿液中百草枯和敌草快

百草枯和敌草快是广泛使用的非选择性触杀型除草剂,中毒后会造成急性肺损伤,病死率高,同时监测血浆和尿液中百草枯和敌草快的浓度,可以为临床早期诊断和预后提供有价值的信息。血浆和尿液中百草枯和敌草快的主要检测方法为液相色谱-质谱法。百草枯和敌草快为强极性水溶性化合物,在反相色谱柱上难以保留,多采用离子对色谱法或亲水色谱法进行分离。采用离子对色谱法时,加入的离子对试剂有离子抑制作用,降低了质谱检测的灵敏度,还给质谱系统增加了额外的污染;亲水色谱法易受基质成分影响,保留时间不稳定。考虑到百草枯和敌草快在水溶液中以双电荷联吡啶离子状态存在,更适合采用阳离子交换色谱法,建立了离子色谱-三重四极杆质谱测定血浆和尿液中百草枯和敌草快的检测方法。血浆和尿液样品经水稀释后,直接过混合型聚合物反相吸附和弱阳离子交换固相萃取柱（Oasis WCX）净化,经IonPac CS 18型阳离子色谱柱（250 mm×2.0 mm,6.0 μm）分离,以自动在线产生的甲磺酸进行梯度洗脱,色谱柱流出液经阳离子抑制器抑制后进入质谱系统,在ESI⁺ 、多反应监测（MRM）模式下检测,稳定同位素内标法定量。百草枯和敌草快分别在1.0~150 μg/L和0.5~75 μg/L范围内线性关系良好,血浆中的平均基质效应分别为84.2%~89.3%和84.7%~91.1%,尿液中平均基质效应分别为50.3%~58.4%和51.9%~59.4%;血浆中百草枯和敌草快的平均加标回收率分别为93.5%~117%和91.7%~112%,相对标准偏差（RSD）分别为3.4%~16.7%和2.8%~13.2%;尿液中百草枯和敌草快的平均加标回收率分别为90.0%~118%和99.2%~116%,RSD分别为5.6%~14.9%和2.4%~17.3%（n =6）;血浆和尿液中百草枯和敌草快的检出限分别0.3 μg/L和0.2 μg/L,定量限分别为1.0 μg/L和0.5 μg/L。该法灵敏度高,准确性好,可用于血浆和尿液中百草枯和敌草快的中毒检测。     

Screening of carbohydrates in urine by capillary electrophoresis

Carbohydrate analysis of urine is clinically important in assisting diagnosis of disorders of carbohydrate metabolism and understanding its pathologic significance. Paper chromatography and thin-layer chromatography are the techniques that are often employed for the determination of urinary carbohydrates. An aim of our experiments was to investigate the utility of capillary electrophoresis to develop a fast screening procedure of urinary carbohydrates. Simultaneous resolution of eight carbohydrates involving maltose, lactose, D-mannose, D-glucose, D-ribose, D-xylose, L-arabinose and D-galactose as markers was obtained with 130 mM borate (pH 10.2). Ethanol/water (80/20 v/v) and acetonitrile proved to be efficient reagents for urine sample clean-up which produced symmetrical peaks. The urine sample from a normal subject was determined to contain lactose, glucose, xylose and arabinose that fall within normal ranges of these carbohydrates in urine. The investigations made in this study may be potentially useful in carbohydrate screening, especially in neonatal urine screening.     

Determination of drugs used as anti-Parkinson's disease drugs in urine and serum by capillary electrophoresis

A new capillary electrophoresis method to determine simultaneously eight of the most important anti-Parkinson's disease compounds has been developed. The generic names of the drugs studied are benactyzine (BA), trihexyphenidyl (TP), fenpiverin (FP), diphemin (DF), scopolamine (BL), adiphenine (TS), diethylaminoethylester 1-phenylcyclopentane-1-carboxylate (EKK), and diethylaminoethylester tetramethoxydiphenylacetate (EKO). An untreated fused-silica capillary tube (75 microns i.d., 57 cm total length, 49.5 cm length to the detector) was used with detection at 190 nm. The optimal separation conditions were 50 mM phosphate buffer (pH 2.7) with 7 mM-beta-cyclodextrin, electrokinetic injection for 15 sec at 5 kV, temperature 25 degrees C, and 15-20 kV separation voltage. Complete separation of all compounds was achieved in less than 16 min. The procedure was applied for the determination in urine and serum. The limits of detection (LOD, S/N = 3) for serum were 209 (FP), 234 (EKO), 168 (DF), 182 (BA), 168 (TP), 220 (BL), 174 (TS), and 163 (EKK) ppb. The method can be used for the therapeutic drug monitoring of these central active cholinolytics in clinical laboratories.     

Separation of nitrophenols by capillary zone electrophoresis

Separation conditions suitable to a rapid resolution of a group of eight nitrophenols by capillary zone electrophoresis (CZE) were found. Required differences in their effective mobilities were achieved via host-guest complexation of -cyclodextrin combined with intermolecular interactions involved by polyvinylpyrrolidone. When both additives were present in the carrier electrolyte at pH=9.1 nitrophenols could be separated in the column of a, 300 m I.D. and 180 mm in the length within 8–9 minutes. It is shown that the column of such an I.D. providing enhanced sample load capacity, can operate with high separation efficiencies as maintaining zone dispersions due to Joule heating on a tolerable level. CZE on-line coupled with isotachophoretic sample pretreatment is shown to provide the concentration limits of detection at low ppb concentrations by using an on-column photometric detector operating at 254 and 405 nm detection wavelengths.     

Separation and detection of lanthanides by capillary electrophoresis

Due to the importance of application of lanthanides in various industries especially the nuclear ones, and the advantages of capillary electrophoresis method in separation of metal cations, this research was carried out in order to investigate the separation potential of lanthanides using capillary electrophoresis via simulation method at laboratory scale. Since the properties of various types of lanthanides are very similar, the separation of lanthanides using the usual approaches was not possible. Thus, the separation of lanthanides was devised upon partial, competing complexation in order to differentiate their properties. Salicylic acid was firstly used as the primary UV-absorbing ligand, whereas formic, acetic, lactic, tartaric and citric acids, which showed no absorption in UV-spectrum and had weaker complexes in comparison to salicylic acid, were used as auxiliary ligands. Upon the results of spectrometry, the wave length of 210 nm was selected for detecting lanthanides. The properties and stability of lanthanides were examined and furthermore acetic and citric acids were selected as auxiliary ligands. The simulation was carried out with respect to the transport phenomena in the unsteady state. The ion species dissociation was found to be directly dependent upon the concentration, and was also used in complexation. The results of simulation showed that the diffusion control of H⁺ and homogenizing electrical field promoted separation quality. The separation conditions were optimized by using the simulation results as well as the tests obtained. In order to optimize the experimental conditions, variable factors such as voltage, injection time, pH, temperature and ionic strength were examined. Also, methanol was used as dissolving modifier as well as noise reducer on the base line. Sodium nitrate was used as ionic strength controller and sucrose for increasing viscosity which optimized separation quality.     

Separation of metal ions by capillary electrophoresis

A number of experimental parameters have been optimized for the separation of 26 metal ions, including alkali, alkaline earth, transition and lanthanide metal ions. Experimental parameters that were evaluated included nature of indirect-detection reagent, pH of electrolyte, concentration of complexing agent and nature of the surface of the capillary; unbonded and C₁ and C₁₈ bonded phases were studied. In addition the effect of internal diameter on linearity and signal-to-noise ratio was examined, and separation efficiency was determined for a variety of experimental conditions. Detection limits (signal-to-noise RATIO = 3) were ca. 1 μg/ml for the lanthanides, ca. 0.6 μg/ml for transition and alkaline earth ions and ca. 0.1–0.8 μg/ml for alkali metal ions. The average relative standard deviations of were 3.7, 5.1 and 2.5% on unbonded, C₁ and C₁₈ capillaries, respectively. Whereas conventional regression analysis suggested that the calibration curves were linear over the range of 1·10⁻⁵ to 4·10⁻⁴ mol/l, sensitivity plots showed that the results were actually linear to within 6% only over the range of 2.5·10⁻⁵ to 4·10⁻⁴ mol/l.     

Separation of diadenosine polyphosphates by capillary electrophoresis

The influence of buffer composition and pH on the electrophoretic behavior of diadenosine polyphosphates with a phosphate chain ranging from two to five phosphate groups has been examined. The electrophoretic mobility in carbonate buffer increases according to the number of phosphates, whereas in borate buffer the mobility changes in an irregular way as a function of pH. This finding can be rationalized by a well-known interaction of borate with ribose rings, which modifies the charge and the hydrodynamic radius of each diadenosine polyphosphate in a different way. Our study shows that the best separation of diadenosine polyphosphates can be achieved at the highest pH values of the range examined both in borate and carbonate buffers.     

Separation of neutral carbohydrates by capillary electrophoresis

The basic strategies for analysis of neutral carbohydrates by capillary electrophoresis are summarized. Neutral carbohydrates are dissociated in strong alkali to give anions, hence they can be separated directly by zone electrophoresis based on the difference between their dissociation constants. However, neutral carbohydrates are not electrically charged under normal conditions. Therefore, they should be converted to ions prior to or during analysis. Precapillary introduction of a basic or an acidic group to a neutral carbohydrate gives the derivative positive (in acidic media) or negative (in alkaline media) charge, respectively. The derivatives thus obtained can be separated by zone electrophoresis. Analysis of carbohydrates in a carrier containing an oxyacid salt (such as sodium borate) or an alkaline metal salt (such as calcium acetate) causes in situ conversion to anionic or cationic complexes, respectively, which are separated by zone electrophoresis. The effective uses of electrokinetic chromatography in sodium dodecyl sulfate micelles for hydrophobic derivatives (such as 1-phenyl-3-methyl-5-pyrazolone derivatives) and size-exclusion electrophoresis in gel-packed capillaris for size different oligosaccharides are also discussed. Each separation mode has its inherent method(s) for detection, which are also described here.     

Hemoglobin A2 quantification by capillary zone electrophoresis

Hemoglobin A2 (HbA2) comprises about 2.2% of the total hemoglobin in the erythrocytes. The separation and quantitation of this minor hemoglobin by capillary electrophoresis (CE) using an arginine Tris buffer is described. Some of the variables affecting the accuracy and precision of HbA2 quantification are investigated. Furthermore, the quantification of this hemoglobin by CE is compared to that of a microcolumn chromatography method. The CE method is better suited than the microcolumn method for measuring HbA2 in the sickle cell trait.     

Creatinine determination in serum by capillary electrophoresis

Creatinine in human serum was separated in a fused-silica capillary with H3PO4 (75 mmol/L, pH 2.5) as BGE, followed by UV detection at 200 nm. Serum with methylimidazole added as internal standard was deproteinized with acetonitrile and the supernatant, after dilution with water was injected at pressure mode. Creatinine and methylimidazole were baseline-resolved in 6.5 min. Linearity in the 0-880 micromol/L range gave an r2 > or = 0.998, recovery was 102 +/- 2.8% (n = 6). Enzymatic breakdown with creatininase confirmed that serum does not interfere. The within-day and between-days coefficient of variation (CV) were < or = 2.16 and 2.7%, respectively. The accuracy, determined for lyophilized samples by isotope dilution gas chromatography-mass spectrometry was < or = +/- 2.0%. The results were compared with HPLC for 32 lyophilized samples and on 27 serum pools. Capillary electrophoresis, rapid and inexpensive, seems a promising alternative to high-performance liquid chromatography (HPLC) for creatinine determination in human serum.     

Separation of nicotine metabolites by capillary zone electrophoresis and capillary zone electrophoresis/mass spectrometry

The use of capillary zone electrophoresis (CZE) and capillary zone electrophoresis/mass spectrometry (CZE/MS) has been demonstrated, in principle, for the separation of nicotine and nicotine metabolites. The buffer system developed for separation and detection by CZE/UV was modified for use in CZE/MS analysis. Several of the metabolites are isobaric and tandem mass spectrometric (MS/MS) techniques have been used to differentiate such analytes.