Thermally stable polymers derived from 2,3,5,6-tetraaminopyridine

The stable trihydrochloride salt of 2,3,5,6-tetraaminopyridine (TAP) has been found to be a versatile intermediate to a variety of thermally stable polymers such as polybenzimidazoles (PBI), polyimidazopyrrolones (pyrrones), and polybenzimidazobenzophenanthroline (BB polymer). The controlled reactivity of two of the four amino sites of TAP · 3HCl towards diacid halides and dianhydrides makes possible the preparation of high molecular weight, soluble polyamide prepolymers at mild temperatures. PBI, pyrrones, and BB polymer are obtained from the linear polyamide precursors by heating at 150–375°C. Unoptimized cyclized polymers were aged isothermally in air at 600°F (316°C) and found to be superior to analogous polymers described in the literature. Weight retentions of up to 97% were observed after 500 hr in air at 600°F.     

Thermally stable silarylene-1,3,4-oxadiazole polymers

The effects of incorporating a p-phenylene- (or m-phenylene)-1,3,4-oxadiazole fragment into the backbone of poly[1,4-phenylene(diphenylsilyl)-1,4-phenylene-2,5-(1,3,4-oxadiazole)], which was developed by the authors, was investigated. Bis[(p-carbohydrazidophenyl)]diphenylsilane was copolymerized with dipentachlorophenyl terephthalate or isophthalate to produce the prepolymers poly[N-(p-diphenylsilylbenzoyl)-N′N″-(terephthaloyl)-N″′-(p-benzoyl)dihydrazide] and poly[N-(p-diphenylsilylbenzoyl)-N′,-N″-(isophthaloyl)-N″′-p-(benzoyl) dihydrazide], respectively. The polyhydrazides were converted by thermal dehydration into poly[1,4-phenylene(diphenylsilyl)-1,4-phenylene-(1,3,4-oxadiazole-2,5-diyl)-1,4-phenylene-2,5-(1,3,4-oxadiazole)] and poly[1,4-phenyl-ene(diphenylsilyl)-1,4-phenylene-(1,3,4-oxadiazole-2,5-diyl)-1,3,4-(oxadiazole)]. The new polymers were soluble in organic solvents. Films cast from these solutions exhibited good adhesion to glass and metal surfaces. Thermal analysis showed that the heat stability of all these polymers was about the same and that they were resistant to decomposition when heated in air to about 400°C. The results also indicated that these polymers were somewhat less heat-resistant than samples of poly-[1,4-phenylene(diphenylsilyl)-1,4-phenylene-2,5-]1,3,4-(oxadiazole) synthesized from bis(p-carbohydrazidophenyl)diphenylsilane and bis-(p-carbopentachlorophenoxy-phenyl)diphenylsilane.     

Thermally stable polymers based on bis-acenaphthyls

The thermal stability of poly-bis-acenaphthylenyls was studied by dynamic and isothermal TG methods.All these polymers demonstrate high thermal stabilities; increasing length of the dicarboxylic acid leads to an enhancement of the thermal properties of the polymers.

---

Zusammenfassung Mittels dynamischen und isothermischen TG-Methoden wurde die thermische StabilitÄt von Poly-bis-acenaphthylenen untersucht. Jeder dieser Polymere zeigt eine hohe thermische StabilitÄt; lÄngere DicarbonsÄuren führen zu einer Verbesserung der thermischen Eigenschaften der Polymere.

     

Thermally stable polymers from 1,4,5,8-naphthalenetetracarboxylic acid and aromatic tetraamines

Polycondensations of 1,4,5,8-naphthalenetetracarboxylic acid (NTCA) with both 3,3′-diaminobenzidine (DAB) and 1,2,4,5-tetraaminobenzene tetrahydrochloride (TAB) in polyphosphoric acid (PPA) were found to produce soluble polymers which exhibit excellent thermal stabilities. Polymer structures were deduced from infrared, thermal, and elemental analyses of model compounds and polymers. Polymer derived from TAB had a ladder-type structure. Polymers with solution viscosities near 1 or above (determined in H₂SO₄) were obtained from polymerizations near 200°C., and analysis showed these to possess a very high degree of completely cyclized benzimidazobenzophenanthroline structure. Less vigorous reaction conditions gave polymers with lower solution viscosities which appeared to be less highly cyclized. Low-viscosity polymer was also prepared from DAB and NTCA by solid-phase polycondensation. Some advancements in the solution viscosities of polymers synthesized from DAB in PPA were caused by second staging in the solid phase.     

Thermally stable polymers based on acetylene-terminated adamantanes

1,3-Diethynyl-5,7-dimethyladamantane, 1,3-diethynyl-5-phenyladamantane, 1,3,5-triethynyladamantane, and 3,3′-diethynyl-1,1′-biadamantane, were synthesized and polymerized thermally at 210°C. The thermoset resins obtained were post-cured at 300°C for 16 h to give materials that exhibited onsets of degradation (TGA) in air at 460–477°C and in helium at 460–485°C. The fully cured materials did not exhibit any detectable DSC transitions between 25 and 400°C. An attempt to thermally polymerize 1-ethynyl-3-phenyladamantane was unsuccessful. © 1992 John Wiley & Sons, Inc.     

Thermally stable polymers containing 1,3,4-oxadiazole units obtained from Huisgen reaction

Thermally stable polymers containing 1,3,4-oxadiazole units have been synthesized through Huisgen reaction of the aromatic/aliphatic bis-tetrazole compounds with the aromatic/aliphatic bis-acid chlorides in pyridine as solvent.The obtained polymers are insoluble or slightly soluble even in polar aprotic solvents such as DMSO and DMF.Relatively high inherent viscosity values（0.61-1.33 dL/g,in 0.125%H₂SO₄ at 25℃） were observed for these compounds.Thermal analyses of the polymers using DSC and TGA techniques showed that the polymers have improved thermal stabilities.The glass transition temperature has not been observed in the fully aromatic polymers,but the polymers obtained from 5-[6-（1H-tetrazol -5-yl）hexyl]-lH-tetrazole（Ⅳ） showed very clear T_g.A model reaction was also investigated and the resulting bis-1,3,4-oxadiazole compound was characterized by conventional spectroscopy methods.     

Thermally stable polymers based on 1,3,4-oxadiazole rings

<正>In the present work,new thermally stable polymers containing 1,3,4-oxadiazole units have been synthesized through Huisgen reaction of the aromatic bis-tetrazole compounds with the aromatic/aliphatic bis-acid chlorides in pyridine as solvent.The obtained polymers are insoluble or slightly soluble in polar aprotic solvents such as DMSO and DMF. Thermal analyses of the polymers using DSC and TGA techniques showed that the polymers had improved thermal stabilities.The model reaction was also investigated and the resulting bis-l,3,4-oxadiazole compounds were characterized by conventional spectroscopic methods.     

Thermosetting polymers from epoxy resin and a Nickel catalyst of diethylenetriamine

The kinetics and mechanism of cure reaction of DGEBA using a chelate of Ni(II) with diethylenetriamine (dien), Ni(dien)₂I_2, as a curing agent was studied by DSC. TG curve of the complex curing agent showed mass loss in two region of temperature: 200–320 and 450–550 °C. Dynamic DSC measurements showed only one exothermic peak with a maximum about 250 °C depending on the heating rate. According to the methods of KAS and Ozawa–Flynn–Wall the values of E _a were 92.5 and 96.2 kJ/mol, respectively. The isoconversional kinetic analysis in whole range of conversion, α = 0.02–0.95, showed small changes in the E _a values in the region of α = 0.04–0.6 and most likely represent some average values (E _a = 110 kJ/mol) between the values of E _a of non-autocatalyzed and autocatalyzed reactions. Using the sole dependence of E _a on α, the time required to reach fully cured materials under isothermal conditions were also predicted and compared with the experimental results.     

Thermally stable polymers by condensation of diphenols with glyoxal

Polycondensation of bisphenol A, hydroquinone, or dihydroxynaphthalenes with glyoxal using methane sulphonic acid as condensing agent leads to polymeric materials having linear and ladder structure and high thermal stability. These polymers were characterized by NMR and TG. Oligomers (from dimer to tetramer) were isolated by GPC and their structures characterized.     

Thermally stable polymers from 1,4,5-naphthalene–tricarboxylic acid and aromatic tetramines

New thermally stable polymers that contained benzimidazole and benzimidazobenzoisoquinoline fragments in polymer chains were synthesized by one-stage cyclopolycondensation of aromatic tetramines (3,3′, 4,4′-tetraminodiphenyl ether, 3,3′,4,4′-tetraminodiphenyl methane, 3,3′,4,4′-tetraminodiphenyl sylfone, and 3,3′-diaminobenzidine) with 1,4,5-naphthalene tricarboxylic acid 4:5–anhydride in polyphosphoric acid and with 1,4,5-naphthalene tricarboxylic acid 4:5–anhydride 1-phenyl ester. All polymers obtained were soluble in concentrated sulfuric acid, 85% phosphoric acid, polyphosphoric acid, methane sylfonic acid. Some were soluble in formic acid. Thermogravimetric analyses indicated that these polymers were stable up to 450–500°C in air. The polymers had good hydrolytic stability.     

Fracto-emission from neat epoxy resin

Fracto-emission is the emission of particles (e.g. electrons, photons, ions, neutral species) due to crack growth in materials. These emissions can be related to a number of fracture related phenomena including microcracking, crack speed of dynamic crack growth, locus of fracture (in filled materials), and potentially the extent of crack branching. Here, we examine the emission of electrons, positive ions, and photons during and following the fracture of a neat epoxy resin subjected to tensile and tensile impact loading in vacuum. Experiments which detect correlations of crack tip position and emission intensity show that the emissions occur during and following fracture. We also illustrate that observed variations of the fracture surface morphology under different loading conditions correlated with characteristics of the photon and charged particle emission. For example, regions of the surface exhibiting the highest degree of surface roughness resulted in more intense emission.     

Development and characterization of a novel skeletal modified tetraglycidyl epoxy toughened DGEBA epoxy matrices

The present work investigates the improvement in mechanical properties observed for commercially available diglycidyl ethers of bisphenol-A (DGEBA) with the incorporation of a new type of skeletal modified tetra glycidyl epoxy resin TGBAPB as modifier. Varying weight percentages of TGBAPB have been blended with DGEBA and cured with diaminodiphenylmethane (DDM). The chemical structure of TGBAPB was confirmed by FTIR, NMR, and molecular weight determination was carried out by ESI-MS spectroscopic techniques. The thermal properties were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and mechanical properties like tensile strength, flexural strength, impact strength were also studied by universal testing machine (UTM). Scanning electron microscopy (SEM) investigates the morphological behavior of the neat and blend epoxy resins. The results from different studies indicate that the blend epoxy resin system “B” comprising 75% DGEBA/25% TGBAPB has shown improvements in both toughness and stiffness, despite the fact that it is often found that the enhancement of these two properties together in a material cannot be simultaneously achieved. These aspects of this work are novel.     

Preparation of silicon-containing polymers IV. Thermally stable organosilicon poly-1,2,4-triazoles

Novel silicon-containing poly-1,2,4-triazoles have been synthesized by the reaction of polyhydrazide precursors and aniline in polyphosphoric acid (PPA) at 260°C. The polyhydrazide intermediates were prepared from aromatic dihydrazides and silicon-containing acid dichlorides via interfacial polycondensation. These polymers and their intermediates were characterized by infrared spectroscopy (IR), solubility, and by solution viscosity. The thermal behavior of these polytriazoles has been studied by dynamic thermogravimetry.     

Functional metallomacrocycles and their polymers. XXII. Thermally stable metallophthalocyanine formaldehyde condensation resins

A novel class of urea-formaldehyde condensation resins containing covalently bound metallophthalocyanine [M = A1(III), Co(II), Ni(II), or Cu(II)] was synthesized from [tetrakis(methyl-olamide)phthalocyaninato] metal complexes and dimethylolurea in aqueous solution by heating at 120°C for 10 h, followed by heating at 150°C for about 1 day. The structures of the polymers obtained were characterized by infrared and reflection electronic spectra. The thermal stabilities of the resins were evaluated by dynamic thermogravimetric analyses. The resin containing 21.3 wt % Ni(II)-metallophthalocyanine had the greatest thermal stability, with 82 wt-% char yield at 600°C in air atmosphere.     

Thermally stable polymers based on bismaleimides containing amide,imide, and ester linkages

Seven new structurally different bismaleimides were synthesized and characterized by infrared and proton nuclear magnetic resonance spectroscopy. The chain of these polymer precursors was extended by incorporating amidized, imidized, and esterified 4-chloroformyl phthalic anhydride. The bismaleimides containing amide and imide linkages were prepared by a simple synthetic route based on the reaction of the monomaleamic acid derived from various aromatic diamines (1 mol) with 4-chloroformyl phthalic anhydride (0.5 mol) and subsequent cyclodehydration of the intermediate triamic acid. In addition, chain extended bismaleimides were prepared by reacting the monomaleamic acid derived from p-phenylenediamine with several dianhydrides such as p-phenylene bis(trimellitamide anhydride), p-phenylene bis(trimellitate anhydride), and bis-phenol A bis(trimellitate anhydride). The differential thermal analysis scans of bismaleimides showed exotherms at 221–304°C associated with their polymerization reactions. The thermogravimetric analysis traces of polymers did not show a weight loss up to 351–393 and 344–372°C in N₂ and air atmospheres, respectively. The anaerobic char yield of polymers at 800°C was 44–61%. These polymers can be used for fabrication of composites having improved properties.