Synthesis of optically active α-sulfinylacetaldehyde

Optically active α-sulfinylacetaldehyde is prepared by formylation of the (R)-methyl p-tolylsulfoxide anion with N-formylpiperidine.     

Fabrication of titania and titania–silica aerogels using rapid supercritical extraction

Titania (TiO₂) and titania–silica (TiSi) aerogels are suitable for photocatalytic oxidation of volatile organic compounds for pollution mitigation; however, methods for fabricating these aerogels can be complex. In this work we describe the use of a rapid supercritical extraction (RSCE) technique to prepare TiO₂ and TiSi aerogels in as little as 8 h. The RSCE technique uses a metal mold and a four-step hydraulic hot press procedure to bring the solvents in the sol–gel pores to a supercritical state and control the supercritical fluid release process. Resulting TiO₂ aerogels were powdery with BET surface areas of 130–180 m²/g, pore volumes ~0.5 cm³/g and skeletal densities of 3.6 g/mL. Monolithic TiSi aerogels were made using two different methods. An impregnation process, in which titania precursor was added to a silica sol–gel, took 4–8 days to complete with a 7-h RSCE and resulted in translucent aerogels with high surface area (560–650 m²/g) and pore volume (2.0–2.6 cm³/g), bulk densities ranging from 0.1 to 0.4 g/mL and skeletal densities of 2.3 g/mL. A co-precursor method for preparing TiSi aerogels took 8 h to complete. The precursor chemical mixture was poured directly into the mold and processed in a 7-h RSCE process. The resulting aerogels were opaque, with high surface areas (510–580 m²/g), low bulk density (0.03 g/mL), skeletal densities of 2 g/mL and pore volumes of 2.6–3.5 cm³/g. Preliminary solar simulator studies show that TiO₂ and TiSi aerogels are capable of photocatalytic degradation of methylene blue in aqueous solution.     

Nano-sized blue spectral shift in sol–gel derived mesoporous titania films

Following the spectral energy shift of the energy gap (blue shift) of the TiO₂ sol–gel derived films we have evaluated diameters of the nanocrystallites. The TiO₂ films were deposited by dip-coating technique. Two types of mesoporous films were studied: films with porosity ~16% and refractive index (2.15 at wavelength 633 nm) and films with porosity ~46% and refractive index (1.61 at wavelength 633 nm). High porosity and consequently low refractive index was achieved by adding the non-ionic surfactant Triton X-100 to the starting solution as template. The principal goal of the work is to establish the influence of the Triton X-100 on the morphology as well as to establish a possible correlation between the morphology and optical features of the titania films. The surface morphology was explored using AFM method. And the energy gap was determined from the transmission spectra. Analysis of the blue energy spectral shift is performed following the excitonic model.     

Macrocyclic musk compounds—XI : Synthesis of optically active muscone

A simple synthesis of (−)-muscone has been developed by using citronellal and oleyl alcohol as the starting materials.     

Synthesis of mesoporous hydrophobic silica microspheres through a modified sol–emulsion–gel process

Mesoporous silica microspheres were synthesised through a sol–emulsion–gel process using Span 80 as the surfactant in silica sol/n-hexane water in oil emulsion system. Surface modification of the microspheres was done with trimethylchlorosilane to obtain hydrophobic silica microspheres. Various parameters related to the synthesis of microspheres, including concentration of surfactant and viscosities of sol were studied. The hydrophobicity (wettability), thermal stability, porosity, and morphological features were also investigated.     

Synthesis and structural characterization of sol–gel derived titania/poly (vinyl pyrrolidone) nanocomposites

Non hydrolytic sol–gel method was employed to synthesize pure anatase TiO₂ nanocrystals using tetra isopropyl orthotitanate and poly vinylpyrrolidone as precursors. The structural analyses of the prepared samples were carried out using Fourier transform infrared spectroscopy (FT-IR), thermo gravimetric and differential thermal analysis (TG–DTA), X-ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). The capping of PVP around TiO₂ nanoparticles was confirmed by FT-IR spectroscopy, the interaction being via bridging oxygens of the carbonyl (C=O) and the nanoparticle surface. The XRD, Raman and TEM results indicate that the prepared samples had a pure anatase nano-TiO₂ structure. The particle size analysed by TEM ranged between 7 and 12 nm. The size of the nanocrystals evaluated from the XRD spectra and TEM micrograph is well in agreement. The spacing for the crystal planes was also determined using the ImageJ program applied to the TEM micrographs.     

Synthesis of optically active α-benzyl paraconic acids and their esters and assignment of their absolute configuration

The cis- and trans-4-benzylparaconic acids and their ethyl esters were synthesized with high enantiomeric excess by hydrolysis of the corresponding diastereomeric lactonic esters using α-chymotrypsin. Thus, at low conversion values, cis- and trans-4-benzyl-5-oxo-3-tetrahydrofurancarboxylic acids were separately isolated with 99% ee and 92% ee, respectively. Both ethyl ester diastereomers were also obtained in enantiopure form. The absolute configuration of the trans-lactonic acid was assigned by ¹H NMR analysis of its ester derivatives with both enantiomers of 1-(9-anthryl)-2,2,2-trifluoroethanol, while that of the cis-lactonic acid was assigned by means of X-ray analysis of a crystalline derivative. The circular dichroism curves of the products obtained are also reported.     

Energy and electron transfer reactions on silica gel and titania–silica mixed oxide surfaces

Research on Chemical Intermediates - The energy and electron transfer reactions of anthracene co-adsorbed with an electron donor on silica gel and titania–silica mixed oxides have been...     

Morphology and dispersion control of titania–silica monolith with macro–meso pore system

Macroporous gels with bicontinuous morphology in micrometer range were prepared in a titania?Csilica system containing 5 and 7.6 mass?% titania using tetraethoxysilane and four kinds of Ti precursors, two titanium alkoxides, titanium chloride and titanium sulfate, under coexistence of poly(ethylene glycol) (PEG) with an average molecular weight of 20,000. In all the systems with different Ti precursors, the addition of PEG induced phase separation, and the macroporous morphology was formed when the transitional structure of phase separation was frozen-in by sol?Cgel transition of inorganic components. However, we can see large differences in phase separation tendency and Ti dispersion in silica network depending on the Ti precursors used. When titanium alkoxides were added into pure silica sol?Cgel system, phase separation tendency largely decreased, so that low temperature reaction was necessary for macropore formation. When we used titanium salts, on the other hand, phase separation tendency does not change much from pure silica system. The difference has been tentatively attributed to the difference in the mixing level of Ti in silica network. Although titania tended to aggregate when titanium alkoxides were used as precursors, Ti could be well dispersed in silica gel matrix when acetylacetone was added in the alkoxide system or when titanium salts were used as Ti precursors.     

Synthesis of optically active α-aminophosphine oxides and enantioselective membrane transport of acids with their participation

Russian Journal of General Chemistry -     

Synthesis and characterization of mesoporous Mn–Ni oxides for supercapacitors

Mesoporous Mn–Ni oxides with the chemical compositions of Mn_1-x Ni _x O _δ (x = 0, 0.2, and 0.4) were prepared by a solid-state reaction route, using manganese sulfate, nickel chloride, and potassium hydroxide as starting materials. The obtained Mn–Ni oxides, mainly consisting of the phases of α- and γ-MnO₂, presented irregular mesoporous agglomerates built from ultra-fine particles. Specific surface area of Mn_1–x Ni _x O _δ was 42.8, 59.6, and 84.5 m² g⁻¹ for x = 0, 0.2, and 0.4, respectively. Electrochemical properties were investigated by cyclic voltammetry and galvanostatic charge/discharge in 6 mol L⁻¹ KOH electrolyte. Specific capacitances of Mn_1-x Ni _x O _δ were 343, 528, and 411 F g⁻¹ at a scan rate of 2 mV s⁻¹ for x = 0, 0.2, and 0.4, respectively, and decreased to 157, 183, and 130 F g⁻¹ with increasing scan rate to 100 mV s⁻¹, respectively. After 500 cycles at a current density of 1.24 A g⁻¹, the symmetrical Mn_1–x Ni _x O _δ capacitors delivered specific capacitances of 160, 250, and 132 F g⁻¹ for x = 0, 0.2, and 0.4, respectively, retaining about 82%, 89%, and 75% of their respective initial capacitances. The Mn_0.8Ni_0.2O _δ material showed better supercapacitive performance, which was promising for supercapacitor applications.     

Ag nanoparticles deposited onto silica,titania, and zirconia mesoporous films synthesized by sol–gel template method

A variety of Ag nanoparticles/oxide mesoporous films with templated silica, titania, and zirconia was synthesized by sol–gel method at glass, aluminum, and silicon substrates using metal alkoxides (tetraethoxysilane, titanium tetraisopropoxide, and zirconium tetrapropoxide) and AgNO₃ as precursors of oxide films and Ag nanoparticles, respectively, and Pluronic P123 as a template agent. Oxide films alone and Ag/oxide composites were characterized using hexane adsorption, X-ray diffraction (XRD), Raman and ultraviolet (UV)/vis spectroscopies, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) methods. The distribution of Ag nanoparticles within the films, their sizes, intensity, and position of surface plasmon resonance (SPR) absorbance band at λ = 400 nm, as well as the textural and structural characteristics of whole films depend on treatment temperature, types of substrates and oxide matrices, oxide crystallization, and Ag content. Ag nanoparticles form preferably on the outer surface of the films under lower sintering temperatures if the amount of loaded silver is low. Oxide crystallization (e.g., TiO₂) promotes silver embedding into the outer film layer. At higher silver content (≥10 at.%) and higher calcination temperature (873 K), silver nanoparticles could be entrapped more uniformly along the film profile because of more intensive evaporation of silver droplets from the outer surface of the films on heating.     

Synthesis and diastereoselective catalytic hydrogenation of optically active cyclobutyl α,β-dehydro-α-dipeptides

Optically active cyclobutyl (Z)-α,β-dehydro-α-dipeptides have been efficiently synthesized through the coupling of conveniently protected glycine or (S)-phenylalanine residues with a (Z)-dehydro-α-amino acid derivative prepared, in turn, from (−)-verbenone as a chiral precursor. The alternative use of (R,R)- and (S,S)-Et–duphos–Rh as the hydrogenation catalyst led to the stereoselective production of both diastereomeric saturated dipeptides in each case. Thus, the chirality of the catalyst employed has been shown to be the factor governing the configuration of the newly created stereogenic centre. Regarding structural features, both NMR and CD data establish a marked conformational bias for both the unsaturated and the saturated peptides synthesized herein.     

Asymmetric Diels–Alder reactions of optically active oxazolidinone-derived vinylsulfonamides

Chiral vinylsulfonamides bearing an oxazolidin-2-one moiety derived from (R)-2-phenylglycinol and (1R,2S)-norephedrine have been employed as dienophiles in asymmetric Diels–Alder reactions at normal pressure affording d.e.s of up to 99% when EtAlCl₂ or Et₂AlCl were employed as Lewis acids. Theoretical calculations justify the observed enantio- and diastereoselectivity.     

Preparation of porous titania–silica microspheres for treatment of radioactive waste

Titania–silica microspheres have been prepared by sol–gel process. Internal gelation route, which use hexamethylenetetramine as the source of ammonia was used for the preparation spherical gel particles. A cationic surfactant, cetrimide was added in the feed broth for introducing meso-porosity in the gel network. Further paraffin oil emulsion was incorporated in the feed broth before gelation for the formation of larger pores in the gel network. The spherical gel particles thus obtained were washed and heat treated under controlled conditions to remove the entrapped surfactant, paraffin oil and other organic compounds resulting in highly porous intact titania–silica microspheres. The material was characterized by surface area, porosity and by SEM photomicrographs. The ion exchange property of this material was studied using the sorption of plutonium on this material from carbonate medium by distribution coefficient studies and ion exchange column loading and elution experiments.     

Synthesis of optically active β-keto-γ-butyrolactones having a trifluoromethyl group

A number of chiral β-keto-γ-butyrolactones and tetronic acids bearing a trifluoromethyl group on an asymmetric carbon were prepared by ultrasound-promoted Reformatsky-type reactions between an optically active O-trimethylsilylated cyanohydrin of trifluoroacetaldehyde and ethyl α-substituted bromoacetates.     

Synthesis and characterization of amino-functionalized single magnetic core–silica shell composites

The thermal decomposition approach, reverse micro-emulsion system and surface modification technique had been successfully used to synthesis single magnetic core Fe₃O₄@Organic Layer@SiO₂–NH₂ complex microspheres. The magnetization of the magnetic microspheres core could be easily tuned between 28 and 56 emu/g by adjusting the amount of 2-mercaptobarbituric acid. It was found that the Organic Layer to some extent had a protective effect on avoiding Fe₃O₄ being oxidized into Fe₂O₃. Each Fe₃O₄@Organic Layer microsphere could be coated uniformly by about 30 nm of silica shell. The average diameter of the Fe₃O₄@Organic Layer@SiO₂ composites was about 538 nm. The saturation magnetization of the Fe₃O₄@Organic Layer@SiO₂ complex microspheres was 12.5% less than magnetic microspheres cores. The Fe₃O₄@Organic Layer@SiO₂–NH₂ composites possessed a huge application potentiality in specificity enriching and separating biological samples.     

Enzymes immobilized in mesoporous silica: A physical–chemical perspective

Mesoporous materials as support for immobilized enzymes have been explored extensively during the last two decades, primarily not only for biocatalysis applications, but also for biosensing, biofuels and enzyme-controlled drug delivery. The activity of the immobilized enzymes inside the pores is often different compared to that of the free enzymes, and an important challenge is to understand how the immobilization affects the enzymes in order to design immobilization conditions that lead to optimal enzyme activity. This review summarizes methods that can be used to understand how material properties can be linked to changes in enzyme activity. Real-time monitoring of the immobilization process and techniques that demonstrate that the enzymes are located inside the pores is discussed by contrasting them to the common practice of indirectly measuring the depletion of the protein concentration or enzyme activity in the surrounding bulk phase. We propose that pore filling (pore volume fraction occupied by proteins) is the best standard for comparing the amount of immobilized enzymes at the molecular level, and present equations to calculate pore filling from the more commonly reported immobilized mass. Methods to detect changes in enzyme structure upon immobilization and to study the microenvironment inside the pores are discussed in detail. Combining the knowledge generated from these methodologies should aid in rationally designing biocatalyst based on enzymes immobilized in mesoporous materials.     

Combining mesoporous silica–magnetite and thermally-sensitive polymers for applications in hyperthermia

In this work, the synthesis strategy of a multifunctional system of [SBA-16/P(N-iPAAm)/Fe₃O₄] hybrids of interest for magneto-hyperthermia was explored. Magnetite nanoparticles coated by mesoporous silica were prepared by an alternative chemical route using neutral surfactant and without the application of any functionalization method. Monomer adsorption followed by in situ polymerization initiated by a radical was used to incorporate the hydrogel into the pore channels of the silica nanocomposite. Structural and magnetic characterization of the obtained materials was carried out by using thermal analysis, X-ray diffraction, N₂ adsorption desorption isotherms, ⁵⁷Fe Mössbauer spectroscopy, vibrating sample magnetometry and transmission electron microscopy. Measurements of alternating current magnetic-field-induced heating behaviour under different applied magnetic fields showed that the [SBA-16/P(N-iPAAm)/Fe₃O₄] hybrid here synthesized is suitable as a hyperthermia agent for biological applications.