Systematic studies of silica gels with covalently immobilized thiosemicarbazide and formazan groups under the conditions of competitive sorption from multicomponent systems were conducted. A methodological approach to determine the selectivity of the modified sorption material with regard to Cu(II), Ni(II), Co(II), Cd(II), and Zn(II) was proposed. Solid-phase extraction in equilibrium conditions of Cu(II), Zn(II), Co(II), Cd(II), and Ni(II) on a silica gel with covalently immobilized thiosemicarbazide and formazan groups in the conditions of competitive sorption was studied. The possibility to use the pseudo-second-order kinetic equation for assessment of mutual influence at competitive sorption has been shown. We found that sorption from multicomponent solutions proceeds as a non-additive process under the conditions of an excess of functional groups.
The behaviour of alginate gel film in response to the tensile load is analysed in this paper. The bubbles of 0.5?mm diameter were embedded in the film by the fluidic method prior to gelation, thus providing uniform voidage over the entire film. Further, the intrinsic porosity of the gel matrix around the voids was varied by removing water through either evaporation under vacuum, or employing lyophilisation. The Poisson’s ratio and the modulus of elasticity were estimated from direct measurements. The viscoelasticity of the gel matrix was characterized from stress-relaxation measurement. The transient response to tensile loading and the evolution of stress contours were studied through numerical simulation in ANSYS. The ultimate strength was studied for the gel films with embedded voids of different sizes. The numerical simulations were validated by experimental measurements.
The replacement of antibodies by molecularly imprinted polymers (MIPs) has been investigated for many decades. However, indirect protocols (including natural primary and secondary antibodies) are still utilized to evaluate the ability of MIP thin films to recognize target molecules. MIPs can be prepared as either a thin film or as particles, and cavities that are complementary to the template can be generated on their surfaces. We have prepared thin film MIPs and particle MIPs prepared by solvent evaporation and phase inversion, respectively, from solutions of poly(ethylene-co-vinyl alcohol) (pEVAL) in the presence of the target analytes amylase, lysozyme, and lipase. These were first adsorbed on MIP thin films and by MIP particles that contain fluorescent quantum dots. Sandwich fluoroimmunoassays were then conducted to quantify them in MIP-coated 96-well microplates. The method was applied to determine amylase in saliva, and results were compared with a commercial analytical system.
We have investigated the gas sensing properties of ZnO thin films (100 to 200 nm thickness) deposited by room-temperature radio frequency magnetron sputtering. The sensitivity of the films to ethanol vapor was measured in the 10 to 50 ppm concentration range at operating temperatures between 200 and 400 °C. A synergetic effect of decreasing grain size and increasing operating temperature was observed towards the improvement of the sensitivity, reaching a value of 54 and a limit of detection as low as 0.61 ppm. The decrease in the grain size resulted in prolonged response time but faster recovery. In any case, both response time and recovery time are < 400 s. The results demonstrate that room-temperature magnetron sputtering is a viable approach to enhance the performances of ZnO films in sensors for ethanol vapor.
Sensor response for ZnO films in presence of 50 ppm ethanol as a function grain size and temperature
A label-free and single-step method is reported for rapid and highly sensitive detection of bisphenol A (BPA) in aqueous samples. It utilizes an aptamer acting as a probe molecule immobilized on a commercially available array of interdigitated aluminum microelectrodes. BPA was quantified by measuring the interfacial capacitance change rate caused by the specific binding between bisphenol A and the immobilized aptamer. The AC signal also induces an AC electrokinetic effect to generate microfluidic motion for enhanced binding. The capacitive aptasensor achieves a limit of detection as low as 10 fM(2.8 fg ⋅ mL− 1) with a 20 s response time. The method is inexpensive, highly sensitive, rapid and therefore provides a promising technology for on-site detection of BPA in food and water samples.
A. AC electrokinetics effect plays a vital role in BPA detection by introducing microfluidic movement to accelerate the molecular transport to the electrode surface.
B. The ACEK capacitive aptasensor has a limit of detection as low as 10 fM (2.8 fg ⋅ mL− 1) with a 20-s response time.
The mesoporous silica samples with different concentrations of phosphonic acid groups on the surface were obtained by direct template synthesis. The block-copolymer Pluronic P123 was used as a template, and sodium meta-silicate with diethylphosphatoethyltriethoxysilane as precursors. According to the SAXS diffractograms, mesoporous silica samples have a p6mm hexagonal symmetry. In addition, we used sol–gel method to synthesize xerogel with the same groups for comparison. All samples possess high values of specific surface area 615–730?m2/g and sorption pore volume. FTIR and potentiometric titration methods were used to investigate the surface layer of these samples. Sorption properties of the samples with phosphonic acid groups were studied in respect to a row of metal cations, among which we focused on lead(II), cadmium(II), and dysprosium(III) cations.
Since the late 1960s, ceric hydrogen phosphates have attracted the attention of scientists due to remarkable ion exchange, sorption, proton-conduction and catalytic properties. In this work, through the application of various solvents, we, for the first time, have obtained monolithic aerogels based on ceric hydrogen phosphates with high porosity (~99%) and extremely low density (~10?μg/cm3). The composition and structure of aerogels were thoroughly studied with XRD, TEM, SEM, XPS, low temperature nitrogen adsorption methods, TGA/DSC, Fourier-transform infrared spectroscopy (FTIR) and small-angle neutron scattering (SANS). The aerogels were found to belong to the fibrous macroporous aerogels family.
In this work, sol–gel-based non-stick ceramic coating formulations were prepared and coated onto aluminum panels in order to investigate their surface properties. The effect of the addition of optimal amount of fluorine-containing silane compound (FAS) on the surface and adhesion properties were also investigated. The morphology, structure, and elemental chemical composition of the coatings were characterized by scanning electron microscopy, atomic force microscopy (AFM), energy dispersion spectrum (SEM/EDAX), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS), respectively. Moreover, several properties of the coatings such as cross-cut adhesion, hardness, gloss, and contact angle (CA) were determined. When fluorine was introduced, the pencil hardness was increased to 6H. Fluorinated non-stick ceramic coatings were found to have good adhesion on the aluminum substrates.
Bismuth ferrite (BiFeO3) nanopowder have been successfully synthesized for the first time via a microwave-assisted sol-gel combustion method by using citric acid as fuel. The resulting nanopowder was characterized using FT-IR, TG-DTA, XRD, EDX, VSM, SEM, and UV-Vis DRS. A ferromagnetic hysteresis loop with a saturation magnetization (MS) of 0.66?emu?g?1 has been observed at room temperature in the sample. The optical properties of the nanosized BiFeO3 showed its small band gap (=2.08?eV) indicates a possibility of utilizing much visible light for photocatalysis.
Degradation of three different endocrine disruptors (EDs) was thoroughly studied on prepared durable thin layers of titanium dioxide with an anatase crystalline structure. Specially constructed laboratory reactors bringing information on all individual processes (photolysis, photocatalysis, sorption) involved in decomposition of the studied EDs (17α-ethynylestradiol, bisphenol A and 4-nonylphenol) were applied. It was found that photolytic removal of EDs is the fastest degradation process; nevertheless, this method may be less effective regarding all indicators including toxicity. It was verified that individual degradation processes (photolysis and photocatalysis) showed a significantly different influence on toxicity of resulting solutions. During the photolytic process, EDs degradation caused increasing toxicity contrary to the photocatalytic process. Obtained results were corroborated by a mathematical model, which showed that a limitation step for photocatalysis is a sorption and for photolysis a toxicity of resulting products.
Barium zirconium titanate (Ba(ZrxTi1?x)O3, BZT) super smooth thin films are synthesized through modified sol-gel dip coating route on fluorine-doped tin oxide substrates with a suitably low calcination temperature. The Fourier tranformed infrared spectroscopy proves that impurities and starting materials are completely removed in the calcination process. Crystallographic phases of the samples are identified by the X-ray diffractometry and confirms that all samples are crystallized into a single perovskite phase. Introducing zirconium into the structure causes a reduction in dielectric constant of barium titanate. The optical properties of the films are also investigated. The results indicate that all samples are highly transparent and zirconium reduces the absorption coefficient. Moreover, the band gap energy of barium titanate increases when doped with zirconium and the highest band gap energy of about 3.71?eV along with the lowest dielectric constant of 850 at frequency of 100?kHz are obtained in 15 at.% zirconium-doped sample.
A novel approach based on sol–gel spin coating method to deposit Zn(O,S) thin film using thiourea(TU) as a sulfur source replacing CdS as buffer layer was developed and the influence of TU concentration on the properties of Zn(O,S) thin films and Cu(In,Ga)Se2(CIGS) solar cells were investigated in this paper. It was found by X-ray diffraction and X-ray photoelectron spectroscopy that sol–gel derived Zn(O,S) thin films were amorphous and composed of ZnS, ZnO as well as Zn(OH)2. The variation of the optical band gap as a function of the S/(S+O) ratio was determined by energy-dispersive spectroscopy and UV-VIS-NIR. The results indicated that the minimum value for band gap of approximate 3.72?eV was obtained when the S/(S+O)?=?0.44. Efficiency of up to 7.28% was achieved for a CIGS solar cell with Zn(O,S) buffer layer from 0.2M TU, which was attributed to the optimized conduction band offset (CBO) of +0.45?eV at the CIGS/Zn(O,S) interface.
Zn(O,S) thin films prepared in sol–gel route was used to replace traditional CdS buffer layer deposited by chemical bath deposition method in Cu(In,Ga)Se2 solar cells. The best efficiency was achieved for CIGS/Zn(O,S)/i-ZnO/ITO heterostructure solar cell with S/(S+O)?=?0.18, which was attributed to the optimized conduction band offset (CBO) of +0.45?eV at the CIGS/Zn(O,S) interface.
In this report, we have primarily studied the influence of nickel (Ni) incorporation on ac electrical conductivity, dielectric relaxation mechanism and impedance spectroscopy characteristics of copper oxide (CuO) thin films synthesized by successive ion layer adsorption and reaction (SILAR) technique. The materials has been characterized using X-ray diffraction and UV–VIS spectrophotometric measurements. Reduction in grain size in doped films up to a certain extent of doping (tentatively 6%) were confirmed from XRD analysis, beyond which there is a reverse tendency. Increase in band gap in doped films were observed up to 6% doping level which could be associated with enhanced carrier density in doped films. Impedance spectroscopy analysis confirmed enhancement of ac conductivity and dielectric constant for doped samples. The results are useful for capacitive application of the films. Beyond 6% doping level, AC conductivity and dielectric constant shows a reverse tendency indicating reduced density of charge carriers. Nyquist plot shows contribution of both grain and grain boundary towards total resistance and capacitance. Imaginary part of complex modulus and imaginary part of complex impedance was used to find the migration/activation energy to electrical conduction process. Nearly identical result was obtained from relaxation frequency/relaxation time approach suggesting hopping mechanism of charge carriers.
Magnetic Fe3O4@SiO2 core shell nanoparticles containing diphenylcarbazide in the shell were utilized for solid phase extraction of Hg(II) from aqueous solutions. The Hg(II) loaded nanoparticles were then separated by applying an external magnetic field. Adsorbed Hg(II) was desorbed and its concentration determined with a rhodamine-based fluorescent probe. The calibration graph for Hg(II) is linear in the 60 nM to 7.0 μM concentration range, and the detection limit is at 23 nM. The method was applied, with satisfying results, to the determination of Hg(II) in industrial waste water.
MgF2 coating solutions were solvothermally treated at 160?°C for different time periods, this procedure induced crystallization and particle growth. Antireflection coatings prepared on glass from these solutions were compared to films derived from untreated precursor material. Ellipsometric porosimetry (EP) was employed to characterize structural features of coatings on glass as function of annealing temperature. Based on precursor solutions that had undergone solvothermal treatment antireflective coatings with a peak transparency exceeding 99% were prepared on PMMA substrates.
Solvothermal treatment of MgF2 precursor solutions results in crystallization of particles that can directly be applied to PMMA substrates for λ/4 antireflective films.
Nano noble metal coating on surface patterned mesoporous semiconductor thin film can play an important role in enhancing visible light harvesting efficiency (LHE) towards improvement in photoelectrochemical (PEC) activity of the material. In this work, one-dimensional (1D) and two-dimensional (2D) mesoscale surface patterns have been created on sol–gel-based titanium tin oxide (TSO) nanostructured thin film on pure silica/indium tin oxide-coated glass by soft lithography. The TSO film matrix is observed to be mesoporous and semicrystalline as evidenced from the structural characterization by transmission electron microscopy and measurement of atmospheric ellipso-porosimetry, respectively. The 2D patterned film exhibits maximum LHE value in visible wavelength region. Further film surface modification has been carried out by depositing nano Au coating onto the bare patterned TSO films by a low temperature solution technique. Under visible light, a significant improvement in PEC activity is found and the gold-coated patterned 2D film shows higher visible LHE as well as >2.7 times higher photocurrent density than bare 2D film. This facile fabrication strategy can create an avenue toward improvement in LHE vis-à-vis the PEC activity of mesoporous mixed metal oxide semiconductor thin film.
Superhydrophilic surfaces without the need of other stimuli are usually realized by constructing a rough morphology. However, constructing rough surfaces usually require specialized equipment or complicated processing. Besides, rough surfaces can cause undesirable scattering, which strongly limits the use in optical devices. In this article, we prepared superhydrophilic TiO2 films with ultra-smooth surfaces using simple sol-gel dip-coating method. The hydrophilicity of the TiO2 films varied with different post-heat treatments. The films heat-treated at 400?°C exhibited a durable superhydrophilicity and anti-fogging property. This superhydrophilicity was attributed to the decrease of surface hydrophobic alkoxy groups and the formation of point defects, i.e., Ti3+ and oxygen vacancies, which are favourable for dissociative water adsorption. The amount of surface organic groups was influenced by autophobicity effects, further hydrolysis and decomposition of residual alkoxy groups. Additionally, the wettability behaviours of the films were also explained from the perspective of the surface energy. These results can benefit the design and manufacture of anti-fogging and self-cleaning superhydrophilic TiO2 films.
Powders of Sm0.6Sr0.4CoO3-δ and La0.6Sr0.4CoO3-δ were synthesized using wet chemical technique. Structural and surface properties of synthesized materials were studied by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), IR spectroscopy, and scanning electron microscopy (SEM). The influence of pH on the phase state, chemical composition, morphology, and fractal dimension of the synthesized powders were investigated. It was found that the change of pH has the influence on phase composition of synthesized powders. The increase of solution pH allows one to obtain homogeneous samples at lower temperatures down to 900–950?°C.
We describe a near-infrared (NIR) fluorescent thrombin assay using a thrombin-binding aptamer (TBA) and Zn(II)-activated CuInS2 quantum dots (Q-dots). The fluorescence of Zn(II)-activated Q-dots is quenched by the TBA via photoinduced electron transfer, but if thrombin is added, it will bind to TBA to form G-quadruplexes and the Q-dots are released. As a result, the fluorescence intensity of the system is restored. This effect was exploited to design an assay for thrombin whose calibration plot, under optimum conditions, is linear in the 0.034 to 102 nmol L−1 concentration range, with a 12 pmol L−1 detection limit. The method is fairly simple, fast, and due to its picomolar detection limits holds great potential in the diagnosis of diseases associated with coagulation abnormalities and certain kinds of cancer.
We developed a simple near-infrared fluorescence assay using thrombin binding aptamer (TBA) and Zn(II)-activated CuInS2 quantum dots for the highly selective and sensitive detection of thrombin.
The influence of the water content in the initial composition on the size of silica particles produced using the Stöber process is well known. We have shown that there are three morphological regimes defined by compositional boundaries. At low water levels (below stoichiometric ratio of water:tetraethoxysilane), very high surface area and aggregated structures are formed; at high water content (>40?wt%) similar structures are also seen. Between these two boundary conditions, discrete particles are formed whose size are dictated by the water content. Within the compositional regime that enables the classical Stöber silica, the structural evolution shows a more rapid attainment of final particle size than the rate of formation of silica supporting the monomer addition hypothesis. The clearer understanding of the role of the initial composition on the output of this synthesis method will be of considerable use for the establishment of reliable reproducible silica production for future industrial adoption.
