A novel spectrophotometric method for batch and flow injection determination of cyanide in electroplating wastewater

A sensitive and highly selective spectrophotometric method is described for the determination of cyanide. It is based on a reaction of cyanide with aquacyanocobyrinic acid heptamethyl ester (ACCbs) reagent (orange color) at pH 9.5 to give dicyanocobester (DCCbs) (violet color). The increase of the absorption bands of the reaction product at 368 and 580 nm and the decrease of the reagent band at 353 nm are linearly proportional to the cyanide concentration. The method is used in static mode for determining cyanide over the concentration range 0.04-1.20 μg ml⁻¹ with a detection limit of 0.02 μg ml⁻¹ and for hydrodynamic analysis of 0.4-5.2 μg ml⁻¹ cyanide. Application for batch and flow injection monitoring of cyanide in electroplating wastewater samples gives results agree within ± 1.2% with those obtained by the standard potentiometry using the cyanide ion selective electrode. The method is practically free from interferences by PO₄³⁻, NO₃⁻, NO₂⁻, SO₄²⁻, F⁻, Cl⁻, Br⁻, I⁻, S²⁻ and SCN⁻ ions and gives results with average recoveries of 97.6-99.2%. Advantages offered by using ACCbs as a chromogen for cyanide assay are: (i) high selectivity and sensitivity of the coordination site of the reagent towards cyanide ion; (ii) fast reaction, since legation takes place at the axial position of the reagent; (iii) good solubility and stability of the reagent in aqueous solutions over a wide pH range; (iv) high stability of the reagent (ACCbs) and the colored complex product (DCCbs) and (v) possible absorbance measurements at three different wavelengths.     

流动注射褪色光度法测定食品中的亚硫酸盐

基于亚硫酸盐在碱性条件下与碱性品红的褪色反应,建立了流动注射光度分析测定食品中亚硫酸盐的新方法.在38样/h采样频率下检出限为0.016μg/mL,SO32-质量浓度在0.04～1.5 μg/mL范围符合朗伯比耳定律,测定1.2μg/mL SO32- 11次,相对标准偏差为0.41%.该法可用于食品中亚硫酸盐的测定.     

A clean method for flow injection spectrophotometric determination of cyclamate in table sweeteners

A flow system based on the multicommutation is proposed for fast and clean determination of cyclamate. The procedure exploits the reaction of cyclamate with nitrite in acidic medium and the spectrophotometric determination of the excess of nitrite by iodometry. The flow system was designed with a set of solenoid micro-pumps to minimize reagent consumption and waste generation. The detection limit was estimated as 30 μmol L⁻¹ (99.7% confidence level) with linear response ranging up to 3.0 mmol L⁻¹. The coefficient of variation was estimated as 1.7% for a solution containing 2.0 mmol L⁻¹ cyclamate (n = 20). About 60 samples can be analyzed per hour, consuming only 3 mg KI and 1.3 μg NaNO₂, and generating 2.0 mL of effluent per determination, thus providing an environmentally friendly alternative to previously proposed procedures. Common artificial and natural sweeteners did not interfere when present in concentrations 10-times higher than cyclamate. The procedure was successfully applied for determination of cyclamate in artificial table sweeteners with results in agreement with the reference method at the 95% confidence level.     

Cobalt phthalocyanine as a novel molecular recognition reagent for batch and flow injection potentiometric and spectrophotometric determination of anionic surfactants

Cobalt(II) phthalocyanine [Co(II)Pc] is used as both an ionophore and chromogen for batch and flow injection potentiometric and spectrophotometric determination of anionic surfactants (SDS), respectively. The potentiometric technique involves preparation of a polymeric membrane sensor by dispersing [Co(II)Pc] in a plasticized PVC membrane. Under batch mode of operation, the sensor displays a near-Nernstian slope of −56.5 mV decade⁻¹, wide response linear range of 7.8 × 10⁻⁴ to 8.0 × 10⁻⁷ mol L⁻¹, lower detection limit of 2.5 × 10⁻⁷ mol L⁻¹ and exhibits high selectivity for anionic surfactants in the presence of many common ions. Under hydrodynamic mode of operation (FIA), the slope of the calibration plot, limit of detection, and working linear range are −51.1 mV decade⁻¹, 5.6 × 10⁻⁷ and 1.0 × 10⁻³ to 1.0 × 10⁻⁶ mol L⁻¹, respectively. The spectrophotometric method is based on the use of [Co(II)Pc] solution in dimethylsulfoxide (DMSO) as a chromogenic reagent. The maximum absorption of the reagent at 658 nm linearly decreases with the increase of anionic surfactant over the concentration range 2-30 μg mL⁻¹. The lower limit of detection is 1 μg mL⁻¹ and high concentrations of many interfering ions are tolerated. Flow injection spectrophotometric measurements are carried out by injection of the surfactant test solution in a stream of the reagent in DMSO. The sample throughput, working range and lower detection limit are 25-30 samples h⁻¹, 4-60 and 2 μg mL⁻¹, respectively. The potentiometric and spectrophotometric techniques are applied to the batch and flow injection measurements of anionic surfactants in some commercial detergent products. The results agree fairly well with data obtained using the standard methylene blue spectrophotometric method.     

流动注射光度法直接测定海水中的微量苯胺

基于苯胺与亚硝酸盐的重氮化反应及反应产物与甲萘酚的显色,借助流动分析技术,实现了海水中苯胺含量的分析测定。体系以30.9g/L的NaCl做载液、人工海水配制标准样品,对各个影响因素进行了优化。苯胺浓度在0.01～1.0mg/L范围内与相对峰高呈线性关系,线性方程ΔH(mV)=200.53ρ+1.0728(n=8,ρ为苯胺浓度mg/L),相关系数R2=0.9982。方法的检出限(3σ)为0.005mg/L,相对标准偏差(RSD)为4.8%(n=11)。考察了共存离子、不同盐度样品对分析测定的影响。用于实际海水样品的分析,回收率为95.8%～106.6%。     

Hybrid sequential injection-flow injection manifold for the spectrophotometric determination of total sulfite in wines using o-phthalaldehyde and gas-diffusion

A new automated spectrophotometric method for the determination of total sulfite in white and red wines is reported. The assay is based on the reaction of o-phthalaldehyde (OPA) and ammonium chloride with the analyte in basic medium under SI conditions. Upon on-line alkalization with NaOH, a blue product is formed having an absorption maximum at 630 nm. The parameters affecting the reaction - temperature, pH, ionic strength, amount concentration and volume of OPA, amount concentration of ammonium chloride, flow rate and reaction coil length - and the gas-diffusion process - sample and HCl volumes, length of mixing coil, donor flow rate - were studied. The proposed method was validated in terms of linearity (1-40 mg L⁻¹, r = 0.9997), limit of detection (c_L = 0.3 mg L⁻¹) and quantitation (c_Q = 1.0 mg L⁻¹), precision (s_r = 2.2% at 20 mg L⁻¹ sulfite, n = 12) and selectivity. The applicability of the analytical procedure was evaluated by analyzing white and red wine samples, while the accuracy as expressed by recovery experiments ranged between 96% and 106%.     

流动注射光度法测定盐酸普鲁卡因

在盐酸介质中,利用盐酸普鲁卡因－亚硝酸钠－α萘胺的重氨化－偶合反应,建立了流动注射光度法测定盐酸普鲁卡因的新方法。利用控制加 权形心单纯形优化法选择最佳实验条件,测定的线性范围为0－30μg/mL,该法已用于药物中盐酸普鲁卡因含量的测定。     

Rapid determination of chromium(VI) in electroplating waste water by use of a spectrophotometric flow injection system

A new rapid and sensitive FI method is reported for spectrophotometric determination of trace chromium(VI) in electroplating waste water. The method is based on the reaction of Cr(VI) with sodium diphenylamine sulfonate (DPH) in acidic medium to form a purple complex (lambda(max) = 550 nm). Under the optimized conditions, the calibration curve is linear in the range 0.04-3.8 microg ml(-1) at a sampling rate of 30 h(-1). The detection limit of the method is 0.0217 microg ml(-1), and the relative standard deviation is 1.1% for eight determinations of 2 microg ml(-1) Cr(VI). The proposed method was applied to the determination of chromium in electroplating waste water with satisfactory results.     

Development of novel detection reagent for simple and sensitive determination of trace amounts of formaldehyde and its application to flow injection spectrophotometric analysis

In this paper, a novel detection reagent for formaldehyde determination is proposed, and is applied to a simple and highly sensitive flow injection method for the spectrophotometric determination of formaldehyde. The method is based on the reaction of formaldehyde with methyl acetoacetate in the presence of ammonia. The increase in the absorbance of the reaction product was measured at 375 nm. An inexpensive light emitting diode (LED)-based UV detector (375 nm) was, for the first time, used. Under the optimized experimental conditions, formaldehyde in an aqueous solution was determined over the concentration range from 0.25 to 20.0 × 10⁻⁶ M with a liner calibration graph; the limit of detection (LOD) of 5 × 10⁻⁸ M (1.5 μg L⁻¹) was possible. The relative standard deviation of 12 replicate measurements of 5 × 10⁻⁶ M formaldehyde was 1.2%. Maximum sampling throughput was about 21 samples/h. The effect of potential interferences such as metals, organic compounds and other aldehyde was also examined. The analytical performance for formaldehyde determination was compared with those obtained by the conventional acetylacetone method, which uses visible absorption spectrophotometry. Finally, the proposed method was successfully applied to the determination of formaldehyde in natural water samples.     

Simple flow injection method for simultaneous spectrophotometric determination of Fe(II) and Fe(III)

The method is based on spectrophotometric determination of Fe(II) and Fe(III) at a single wavelength (530 nm) with the use of a dedicated reversed-flow injection system. In the system, EDTA solution is injected into a carrier stream (HNO₃) and then merged with a sample stream containing a mixture of sulfosalicylic acid and 1,10-phenanthroline as indicators. In an acid environment (pH ≅ 3) the indicators form complexes with both Fe(III) and Fe(II), but EDTA replaces sulfosalicylic acid, forming a more stable colourless complex with Fe(III), whereas Fe(II) remains in a complex with 1,10-phenenthroline. As a result, the area and minimum of the characteristic peak can be exploited as measures corresponding to the Fe(III) and Fe(II) concentrations, respectively. The analytes were not found to affect each other's signals, hence two analytical curves were constructed with the use of a set of standard solutions, each containing Fe(II) and Fe(III). Both analytes were determined in synthetic samples within the concentration ranges of 0.05–4.0 and 0.09–6.0 mg L⁻¹, respectively, with precision less than 1.5 and 2.6% (RSD) and with accuracy less than 4.3 and 5.6% (RE). The method was applied to determination of the analytes in water samples collected from artesian wells and the results of the determination were consistent with those obtained using the ICP-OES technique.     

A membraneless gas diffusion unit: design and its application to determination of ethanol in liquors by spectrophotometric flow injection

This work presents new design of a gas diffusion unit, called ‘membraneless gas diffusion (MGD) unit’, which, unlike a conventional gas diffusion (GD) unit, allows selective detection of volatile compounds to be made without the need of a hydrophobic membrane. A flow injection method was developed employing the MGD unit to determine ethanol in alcoholic drinks based on the reduction of dichromate by ethanol vapor. Results clearly demonstrated that the MGD unit was suitable for determination of ethanol in beer, wine and distilled liquors. Detection limit (3S/N) of MGD unit was lower than the GD unit (GD: 0.68%, v/v; MGD: 0.27%, v/v). The MGD design makes the system more sensitive as mass transfer is more efficient than that of GD and thus, MGD can perfectly replace membrane-based designs.     

A novel method for the spectrophotometric determination of nitrite in water

A rapid, simple, selective and sensitive method for the spectrophotometric determination of nitrite in water has been developed and optimum reaction conditions along with other analytical parameters have been evaluated. Nitrite reacts with barbituric acid in acidic solution to give the nitroso derivative, violuric acid. At analytical wavelength of 310 nm, Beer's law is obeyed over the concentration range 0.00–3.22 ppm of nitrite. The molar absorptivity is 15330 ± 259.7 (95%) with pooled standard deviation of 355.57 and R.S.D. of 2.32%. As well as the method is sensitive (2.99 × 10⁻³ μg NO₂ cm⁻²) and selective, it tolerates most of the potential interferents. It has been successfully applied to nitrite determination in natural waters by use of a calibration graph with determination limit of 1.66 μg NO₂ in 100 mL working solution corresponding to minimum 9.5 ppb NO₂–N in water samples. Lower concentrations of nitrite (3.0 μg NO₂/L sample) is precisely analyzed by using the method of dilution with sample, with R.S.D. of lower than 0.5%. The results were compared with standard N-(1-naphtyl)ethylenediamine dihydrochloride method and very good agreement between the data was observed. The method can easily be applied in the field.     

非镉柱还原-流动注射分光光度法检测硝酸盐

阐述了一种基于碱性条件下,采用还原液将硝酸盐还原为亚硝酸盐,从而实现淡水中硝酸盐的还原液-流动注射分光光度检测方法,通过优化实验确定了最优分析条件。硝酸盐浓度在50～2000μg/L范围内与峰高呈良好的线性关系,方法检出限3.5μg/L,相对标准偏差0.90%(n=15,500μg/L)。方法应用于环境水样中硝酸盐的检测,加标回收率为95.0%～100.2%。该方法避免了镉还原柱再生处理,简化了操作,易于实现无人值守式的在线自动监测。     

Flow injection kinetic spectrophotometric method for the determination of trace amounts of nitrite

In this work, a new, simple and sensitive flow injection catalytic kinetic spectrophotometric determination of nitrite is reported based on catalytic effect of nitrite on the redox reaction between sulfonazo III and potassium bromate in acidic media. The reaction was monitored by measuring the decrease in the absorbance of sulfunazo III at 570 nm. Various chemical (such as the effect of acidity, reagents concentrations) and instrumental parameters (flow rate, reaction coil length, injection volume and temperature) were studied and were optimized. Under the optimum conditions calibration graph was linear in the nitrite concentration ranges of 8.00 × 10⁻³-3.00 × 10⁻¹ μg/ml (with slope of 2.40) and 3.50 × 10⁻¹-1.80 μg/ml (with slope of 0.42). The detection limit was 6.00 × 10⁻³ μg/ml of nitrite, the relative standard deviation (n = 10) was 1.25% and 0.88% for 5.00 × 10⁻² and 2.00 × 10⁻¹ μg/ml of nitrite respectively. About 60 samples in 1 h can be analyzed. The interfering effects of various chemical species were studied. The method was successfully applied in the determination of nitrite in food and environmental samples.     

11-Molybdobismuthophosphate—A new reagent for the determination of ascorbic acid in batch and sequential injection systems

The guanidinium salt of the new heteropolymolybdate 11-molybdobismuthophosphate Gua₆PBiMo₁₁O₄₀ (11-MBP) was synthesized, characterized and used as a reagent for batch spectrophotometric (SP) and sequential injection determination of ascorbic acid (AsA). When compared to other Keggin's heteropolyanions, the reduction of 11-MBP with AsA is both fast and maximal within a pH range of 1.6-2.0. The stoichiometry of the reaction was determined using molar ratio and continuous variation methods and was shown to be 1:1. The molar absorptivity of the reduced form of 11-MBP was 6.0 × 10³ L mol⁻¹ cm⁻¹ at 720 nm. The reaction is also specific for AsA. Only cysteine, hydroquinone and hydroxyacids were found to interfere with the reaction, while no interference was observed with the common reducing agents, including reducing sugars, catecholamines, nitrite, sulfite and iron(II) ions. Batch SP and sequential injection analysis (SIA) systems were developed for the determination of AsA, with calibration ranges of the SP methods at 2 × 10⁻⁶-8 × 10⁻⁵ M for a 10 mm cell and 5 × 10⁻⁷-3 × 10⁻⁵ M for a 50 mm cell and a limit of detection at 3 × 10⁻⁷ M. The linear range of the SIA method was 6 × 10⁻⁶-5 × 10⁻⁴ M, with a detection limit of 2 × 10⁻⁶ M and a sample throughput of 15 h⁻¹. The proposed methods were successfully used for the determination of AsA in both pharmaceuticals and fruit juices, and the results were consistent with those provided by the 2,6-dichlorophenolindophenol method.     

Correction of iron interface in the spectrophotometric flow injection catalytic determination of molybdenum in plants

Iron interference in the spectrophotometric catalytic determination of molybdenum based on the iodide-hydrogen peroxide reaction can be corrected by using sulphosalicylic acid as masking and color-forming reagent. The catalytic influence of iron ions is circumvented to the extent of about 90% and correction of any remaining iron ions is possible by monitoring the colored iron(III)-salicylate complex at 490 nm. In this way, iron is also determined. With the proposed system, molybdenum can be determined in plant and food digests within the 0–100 μg Mo 1⁻¹ range in the presence of up to 25 mg Fe 1⁻¹, at a sampling rate of about 50 determinations h⁻¹. The relative standard deviation of 10 consecutive measurements was estimated as < 2%. Results for samples were comparable with those obtained by graphite furnace atomic absorption spectrometry. In addition, recoveries within the range 94–100% were calculated.     

Development of an integrated flow injection system for the electro-oxidative leaching of uranium from geological samples and its spectrophotometric determination with Arsenazo III

This work proposes a new procedure for on-line electro-oxidative leaching and spectrophotometric determination of uranium in ore samples. By associating a conventional flow injection system, used for uranium determination with Arsenazo III, with an on-line system for electro-oxidative leaching, a fully integrated system was assembled. The systems were integrated after achieving optimum conditions for uranium determination and leaching. According to the results obtained in the present work, a current density of 280 mA cm⁻² generated enough hypochlorite ions in the electrolyte solution (3.6 mol L⁻¹ HCl + 2% (w/v) NaCl) to promote quantitative oxidation of U(IV) to U(VI) thus improving the extraction efficiency. The slurry density did not significantly affect the performance of the system and the increasing temperature resulted in a decrease in extraction efficiency. This methodology was applied in the determination of U₃O₈ in four ore samples and the results obtained agreed with those obtained by ICP-MS after conventional wet acid digestion of the samples.     

A very sensitive flow system for the direct determination of copper in natural waters based on spectrophotometric detection

A very sensitive flow injection method with spectrophotometric detection has been developed for the on-line determination of copper in natural waters. The method exhibits a limit of detection three times lower than the most sensitive direct spectrophotometric method previously described and then allows the direct and simple in situ determination of copper in most natural waters.The method was based on the measurement of the absorbance of the coloured complex formed by copper with the chromogenic reagent di-2-pyridyl ketone benzoylhydrazone (dPKBH) in an alkaline medium. This complex presents stoichiometry 1:2 (Cu:dPKBH), and exhibits maximum absorbance at 370 nm. The manifold used was very simple, and consisted of two channels. The first one contained the sample while the second one contained the colorimetric reagent (3.3×10⁻⁴ M dPKBH in 10% ethanol), in a 1.6×10⁻² M phosphate buffer solution at pH 8. The performance of the system was optimised by using both univariate and modified simplex methodologies. When modified simplex was used, the best signal was obtained for a sample injection volume of 529 μl, a reaction coil length of 1.29 m, and a reagent flow rate of 4.8 ml min⁻¹. Under optimum conditions, the response was linear up to 3 mg l⁻¹ copper, the equation of the straight line being y=0.314x+5.2×10⁻⁴ (r²=0.998). The method allowed a sampling frequency of 40 samples per hour and exhibited a precision of 2.11% (as R.S.D., n=11). The limit of detection was 4.6 μg l⁻¹ (calculated as 3s_b/m, where s_b is the standard deviation of the y-intercept and m represents the slope of the straight line), and was therefore more sensitive than all the direct continuous methods reported previously.The method was successfully applied to the analysis of real water samples, with an average relative error of 5.32%.     

Rapid flow injection method for the determination of sulfite in wine using the permanganate-luminol luminescence system

A simple, rapid and sensitive chemiluminescence method for the determination of sulfite has been developed by combining flow-injection analysis and its sensitizing effect on the known chemiluminescence emission produced by the oxidation of luminol in alkaline medium; in this work permanganate has been proposed as oxidizing reactive. The optimum conditions for the chemiluminescence emission were established. The chemiluminescence was proportional to the sulfite concentration over the range 1.6 × 10⁻⁵ and 4.0 × 10⁻⁴ mol L⁻¹. The detection limit was 4.7 × 10⁻⁶ mol L⁻¹ of sulfite. The method has been satisfactorily used for the determination of free and bound sulfite in wines.     

Flow injection spectrophotometric determination of europium using chlortetracycline

A flow injection (FI) spectrophotometric determination of europium (III) is described, based on the complexation between europium (III), and chlortetracycline (CTC) in a Tris-buffer pH 8.0 medium. The resulting yellow-coloured complex is measured at its absorption maximum of 400 nm after 100 μl of sample or standard solution containing europium (III) are injected into the merged streams of CTC and Tris-buffer solutions. Optimum conditions for determining μg amounts of europium (III) are achieved by univariate method. Various types of reactors are also investigated. It is shown that the use of a single bead string reactor gives rise to the enhancement of peak height. A linear calibration curve over the range of 0.10-0.60 μg ml⁻¹ europium (III) is established with the regression equation (n=6) Y=34.93X+0.01 and the correlation coefficient of 0.9994 is obtained. A detection limit (3σ) of 0.01 μg ml⁻¹ of europium (III) and the relative standard deviation (R.S.D.) of 4.32% for determining 1.0 μg ml⁻¹ of europium (III) (n=7) are obtained. The recommended method has been applied to the quantitation of europium (III) in spiked water and stream sediment samples with average recoveries of 99.9 and 97.5%, respectively. The sampling rate is found to be 85 h⁻¹.