溶胶-凝胶固相微萃取涂层及其在农药残留分析中的应用

利用溶胶-凝胶(sol-gel)技术制备固相微萃取(SPME)涂层材料.通过硅醇盐前驱体与涂层聚合物羟基硅油(OH-TSO)的水解共聚的方法,成功地制备了聚二甲基硅氧烷sol-gel 涂层的SPME 萃取头,并以农药的混合标准水溶液为研究对象,用直接-固相微萃取-气相色谱法(GC)对涂层的性能进行考察,制成的萃取头适用于多种农药残留的萃取分离分析.     

固相微萃取活性炭涂层萃取头对水中有机物的定性分析

对自制的固相微萃取（SPME）活性炭（AC）涂层萃取头进行了评价。该涂层富集能力强,对苯系物（BTEX）的富集率达到14．5～19．2倍;热稳定性好,最高使用温度可达290℃;使用寿命长,260℃解吸条件下可反复使用140次以上。其与聚二甲基硅氧烷（PDMS）涂层相比,尽管萃取量略小,但其具有更高精密度和准确度,而且其萃取和解吸平衡时间减少为聚二甲基硅氧烷（PDMS）涂层的一半以上。应用AC涂层SPME法和液-液萃取（LLE）法对松花江水进行了气相色谱-质谱（GC-MS）定性比较分析。两种方法分别检测到50种（主要是挥发和半挥发性的弱极性和非极性）和44种（主要是挥发性差、与正己烷相容性较强）化合物。     

基于自制聚苯胺顶空固相微萃取涂层快速监测水体和牛奶中的痕量多溴联苯醚

采用电化学沉淀法,成功地制备了多孔、高效聚苯胺固相微萃取涂层,并建立了顶空固相微萃取-气相色谱(HS-SPME-GC)快速测定水体和牛奶中的痕量多溴联苯醚的方法。详细研究了萃取模式、萃取温度、萃取时间、顶空体积及离子强度对萃取效率的影响。在优化实验条件下,本法测定的6种多溴联苯醚的线性范围为1~4000 ng/L(除BDE-154和BDE-153分别为1~3000 ng/L、1~2500 ng/L外),相关系数大于0.99,检出限(S/N=3)在0.08~0.20 ng/L之间,相对偏差小于8.5%(n=7)。自制聚苯胺涂层对多溴联苯醚的萃取效率优于商品化100μm-PDMS纤维。将本法用于河水和牛奶中痕量多溴联苯醚的测定,实际样品回收率分别在90%和80%以上。     

固相微萃取-气相色谱/质谱联用快速鉴定香稻香味特征化合物2-乙酰基吡咯啉

建立了固相微萃取-气相色谱/质谱(SPME-GC/MS)联用快速鉴定香稻香味特征化舍物2-乙酰基吡咯啉的方法.香米加入内标物2,4,6-三甲基吡啶,密封,在80℃水浴条件下经固相微萃取(萃取纤维头为100 μm聚二甲基硅氧烷)提取2 h,提取物经毛细管气相色谱柱HP-5MS(30 mx0.25mm×0.25μm)分离,...     

聚硅氧烷富勒烯固相微萃取涂层的性能

高分子聚硅氧烷富勒烯首次被用作固相微萃取涂层材料,利用顶空固相萃取气相色谱法对该涂层进行了评价。与商用的聚二甲基硅氧烷相比,自制涂层在选择性、灵敏度、热稳定性、使用寿命及萃取量等方面的性能均优于商用聚二甲基硅氧烷。     

聚苯乙烯-丙烯酸丁酯新型固相微萃取吸附质的研究与应用

合成了苯乙烯-丙烯酸丁酯共聚物,研究了此聚合物作为固相微萃取吸附质的性能。用顶空萃取法对水中低级芳烃化合物进行了萃取实验,考察了此高聚物涂层的热稳定性及单体比例与萃取率的关系。将自制涂层与商品聚二甲基硅氧烷(PDMS)涂层对低级芳烃化合物的萃取效果进行了比较。     

固相微萃取新型活性炭涂层萃取头的研究

利用合成的有机硅树脂胶粘剂和活性炭微粉首次制成活性涂层萃取头。通过苯系物(BTEX)表征了涂层表观结构、厚度及萃取性能。对苯、甲苯、乙苯、对二甲苯、邻二甲苯等进行固相微萃取,结果表明:该萃取头热稳定性好,最高使用温度可达290℃;使用寿命长,250℃解吸条件下反复使用140余次以后,膜层没有脱落或性能下降的现象。该涂层对苯系物的最低检出质量浓度在0 21～0 94μg L之间。与100μm的商品聚二甲基硅氧烷(PDMS)涂层相比,对苯系物的富集能力整体上相当。     

聚吡咯-离子液体固相微萃取涂层的电沉积制备及其在苯类化合物气相色谱检测中的应用

在0.1 mol/L吡咯-0.1 mol/L对甲苯磺酸-4g/L 1-丁基-3-甲基咪唑四氟硼酸盐水溶液中,通过循环伏安法在不锈钢丝表面制备了新型聚吡咯-离子液体(Polypyrrole-ionic liquid,PPY-IL)涂层.此涂层呈菜花状结构,粒度比PPY小.以5种苯类化合物(即1,2-二甲苯、1,2,4-三氯苯、1,2-二氯苯、1,2,4-三甲苯和1,3,5-三甲苯)为目标分析物,对所得萃取头性能进行了考察.在优化的实验条件(萃取温度:50℃；萃取时间:40 min;搅拌速率:600 r/min; NaCl浓度:0.2 g/mL)下,对这些苯类化合物进行顶空固相微萃取-气相色谱检测,其线性范围为0.6～800 μg/L,单根多次萃取的相对标准偏差小于4.5％(n=5),多根萃取头平行萃取的相对标准偏差为4.5％～12.4％(n=5).PPY-IL萃取头有良好的稳定性,在使用150次后萃取性能仅有很小的变化；在温度升至290℃时不分解.与聚吡咯和聚二甲基硅氧烷萃取头相比,本萃取头对这些苯类化合物有更高的萃取能力.     

溴代十六烷吡啶从碱性氰化液中固相萃取金的研究

基于溴代十六烷吡啶(CPB)与Au(CN)2-络阴离子生成的离子缔合物可被反相键合硅胶固相萃取柱萃取、富集,建立了一种从碱性氰化液中高富集倍数固相萃取金的方法。在碱性介质中,溴代十六烷吡啶(CPB)与Au(CN)2-络阴离子生成离子缔合物,该离子缔合物可被反相键合硅胶固相萃取柱萃取、富集,富集的离子缔合物可用乙醇洗脱,洗脱液经处理后用分光光度法测定,反相键合硅胶固相萃取柱不被破坏而且可重复使用。方法用于从碱性氰化液中固相萃取痕量金,萃取回收率可超过98%,研究了反向固相萃取金的机理,同时提出了一种从碱性氰化液中提取金的新工艺。     

顶空固相微萃取/气相色谱-质谱法测定液态化妆品中8种增塑剂

建立了顶空固相微萃取(HS-SPME)/气相色谱-质谱(GC-MS)同时测定液态化妆品中8种邻苯二甲酸酯类增塑剂(PAEs)的分析方法,并对萃取涂层、萃取温度、搅拌速率、盐浓度等参数进行了优化。最终采用65μm聚二甲基硅氧烷/二乙烯基苯(PDMS/DVB)固相微萃取纤维头,调节待萃取液盐浓度为360 g.L-1,在搅拌速率600 r/min及萃取温度90℃条件下萃取60 min,在250℃进样口解吸4 min后供GC-MS分析。结果表明,该方法对除邻苯二甲酸二苯酯(DPhP)外的7种目标化合物的线性范围为10～2 000μg.kg-1,检出限为0.7～13.6μg.kg-1,回收率为83%～97%,相对标准偏差(RSD)为2.5%～10.0%;由于DPhP在萃取涂层上的保留较弱,其回收率为70%,检出限为75μg.kg-1,RSD为13.9%。该方法能很好地富集基体中的目标化合物,满足液态化妆品中多种PAEs的分析要求。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.