Development and certification of a coal fly ash certified reference material for selected polycyclic aromatic hydrocarbons

The development and certification of a coal fly ash certified reference material (CRM) for polycyclic aromatic hydrocarbons (PAH) is described; this is the first natural matrix CRM for organic environmental analysis in China. The homogeneity and stability of this material have been tested by HPLC. The concentrations of several PAH were determined by use of two independent, different methods – solvent extraction–HPLC analysis with UV detection coupled with fluorescence detection (FLD) and solvent extraction, isolation with a silica column, and GC analysis with flame ionization detection (FID). Five certified values were determined: phenanthrene 7.1 ± 2.6 μg g^–1, anthracene 2.0 ± 0.8 μg g^–1, fluoranthene 7.4 ± 1.9 μg g^–1, pyrene 7 ± 2 μg g^–1, and benzo[a]pyrene 1.3 ± 0.3 μg g^–1. Reference values for several other PAH are also suggested.     

Preparation and certification of two freshwater sediments certified reference materials for polycyclic aromatic hydrocarbons

Two freshwater sediments certified reference materials (CRMs) for 16 polycyclic aromatic hydrocarbons (PAHs) have been developed by the Institute for Environmental Reference Materials (IERM) of Ministry of Environmental Protection (MEP) in China. The methodology for preparing the CRMs of PAHs in sediments is described in this paper. The collected natural sediment samples were air-dried, ground, homogenised, packed, sterilised and tested on stability and homogeneity. Homogeneity results showed that the between-unit variation was confirmed to be below 4.5% for each compound. Stability was assessed after storage of samples for 16 months at temperature less than 30°C and in shade. The certification of the natural sediment matrix CRMs for PAHs was based on the agreement of results using different analytical techniques including gas chromatography/mass spectrometry (GC/MS) and reversed-phase liquid chromatography (LC) by no less than eight collaborating laboratories including IERM. Results of the homogeneity showed that the calculated u_bb′ was 0.9–2.5% for environmental river standard-4 (ERS-4) and 9–2.3% for environmental lake standard-1 (ELS-1), whereas stability results of total 16 PAHs indicated that the calculated u_rel,lts was 4.2% for ERS-4 and 2.2% for ELS-1. Certified values of 16 PAHs in ERS-4 varied from 8.5 to 167 μg/kg and ranged from 0.036 to 2.8 mg/kg in ELS-1.The good comparability, together with the independent confirmation of the assigned mass fraction by using different methods, confirmed that the CRMs are suitable for the method validation and quality control in soil or sediments analysis.     

The trace analysis of polycyclic aromatic hydrocarbons (PAH) adsorbed on coal fly ash

Summary (Carbon-14)-labeled 3,4-benzopyrene was deposited on coal fly ash and alumina (as reference material), desorbed by means of liquid extraction and determined with the help of liquid scintillation counting. Recoveries between 8 and 50 percent were found. A thermal treatment reduces the recovery of 3,4-benzopyrene significantly. The chemical composition of coal fly ash and the type of extractant have a less pronounced effect.

---

Spurenanalyse an Flugasche adsorbierter polycyklischer aromatischer Kohlen Wasserstoffe

Zusammenfassung Mit¹⁴C indiziertes 3,4-Benzopyren wurde als Bezugssubstanz an Flugasche und Tonerde adsorbiert, durch Flüssigextraktion desorbiert und mittels Scintillationszählung bestimmt. Die Wiederfindungsraten betrugen zwischen 8 und 50%. Wärmebehandlung setzt die Wiederfindungsrate beträchtlich herab. Die chemische Zusammensetzung der Flugasche und die Art des Extraktionsmittels haben geringen Einfluß.

     

Performance of a chromatographic procedure used in the certification of reference material for polycyclic aromatic hydrocarbons in sewage sludge

Semi-automatic capillary gas chromatographic method with classical flame ionization detection, which satisfies the conditions for required performance and gave acceptable results within the framework of an interlaboratory certification programme for PAHs in sewage sludge, is described. The interesting feature of the procedure is that it incorporates automatic operations such as sample fractionation by semi-preparative HPLC, fraction collection at signal level recognition and evaporation under nitrogen flow. Multiple injections in the GC capillary column are performed in the on-column mode via an autosampler with temperature-programmable injector. Automatic data acquisition and chromatogram treatment are made via computer software. This partially automatic procedure releases personnel from tedious and time-consuming tasks and its robust character was validated through the certification of reference material for PAHs in sewage sludge, demonstrating its reliable performance.     

Preparation of a reference mussel tissue material for polycyclic aromatic hydrocarbons and trace metals determination

Due to high cost of certified reference materials (CRMs), reference materials (RMs) are preferred to check the method performance in environmental analysis. In this work, a laboratory reference material (LRM) was prepared and characterised to carry out the quality control in monitoring analysis of eight polycyclic aromatic hydrocarbons (PAHs) and nine trace metals in mussel tissue. Mussels were collected in a naturally polluted area. Before the reference material was bottled, the mussel tissue was stabilised by freeze-drying, ground and sieved. For the material characterisation, several statistical tests were applied to check the homogeneity of the analytes in the tissue, and a stability test was performed to study the effect of the storage temperature in the analyte concentration. Other characteristics such as specific density, moisture and lipid contents as well as particle size distribution of the material were determined. Although the LRM had a homogeneous distribution for all PAHs and almost all metals, the stability study showed different results at both storage temperatures studied. For both PAHs and trace metals, the material was suitable to assure the quality control of the analysis.     

Standard reference materials for the determination of polycyclic aromatic hydrocarbons

Summary Since 1980 a number of Standard Reference Materials (SRM's) have been issued by the National Bureau of Standards (NBS) to assist in validating measurements for the determination of polycyclic aromatic hydrocarbons (PAH) and other polycyclic aromatic compounds (PAC). These SRM's are certified for selected PAC and range in analytical difficulty from calibration solutions to complex natural matrix materials, such as air and diesel particulate matter, shale oil, and crude oil. In the past year three new SRM's have been introduced: (1) SRM 1647a Priority Pollutant PAH in Acetonitrile, (2) SRM 1491 Aromatic Hydrocarbons in Hexane/Toluene, and SRM 1597 Complex Mixture of PAH from Coal Tar. The SRM's available from NBS for use in the determination of PAC are described and the concentrations of PAC determined in the natural matrix SRM's are summarized and compared. The primary analytical techniques used for the measurement of PAC in these SRM's were gas chromatography, liquid chromatography, and gas chromatography/mass spectrometry.

---

Standardreferenzmaterialien für die Bestimmung von polycyclischen aromatischen Kohlenwasserstoffen

     

Homogeneity tests and certification analyses of coal fly ash reference materials by instrumental neutron activation analysis

The instrumental neutron activation analysis technique (INAA) was used for homogeneity tests and certification analyses of coal fly ash reference materials ENO, ECH, and EOP prepared at the Institute of Radioecology and Nuclear Techniques (IRANT), Koice, Czechoslovakia. Quantitative estimation of a degree of inhomogeneity was suggested. The relative standard deviations due to inhomogeneity were found to be <1% for macroconstituents and <3% for minor and trace elements for sample weights about 25 mg. The results of determination of the elements Al, As, Ba, Ca, Ce, Co, Cr, Cs, Dy, Eu, Fe, Ga, Hf, In, K, La, Mn, Na, Nd, Ni, Rb, Sb, Sc, Sm, Sr, Ta, Th, Ti, U, V, W, and Zn were compared with the IRANT certified or information values. NBS SRM 1633a Trace Elements in Coal Fly Ash was also analyzed as a control sample and the results for the above elements were compared with the NBS certified, information or literature available values. From these comparisons, inference was made on the quality of the IRANT specified values for the element contents.     

Certification of a new NIST fly ash standard reference material

In June 1993 the National Institute of Standards and Technology (NIST) released the third version of Constituent Elements in Coal Fly Ash Standard Reference Material (SRM 1633b). This material is intended for quality assurance purposes in evaluating the analytical methods used for the determination of constituent elements in coal fly ash or in materials with similar matrices. It has been certified for 23 major, minor and trace elements using ten different analytical techniques. For an element to be certified in a NIST SRM, its concentration is usually determined by at least two independent analytical techniques. The concentrations of additional 24 elements are provided for information only purposes in the new fly ash. Current plans are to certify the concentrations of a number of rare earths upon completion of additional analytical work now in progress. Homogeneity testing was accomplished using instrumental neutron activation analysis and X-ray fluorescence. This presentation summarizes the preparation of this new material and the analytical results used for certification.     

加替沙星纯度标准物质研制

研制加替沙星纯度标准物质。采用质量平衡法和氢谱定量核磁法对加替沙星纯度标准物质候选物进行纯度定值,采用卡尔费休法和热重分析法准确测量了影响主成分纯度的水分含量,并考察了水分含量的稳定性。开展了加替沙星纯度定值、均匀性检验、稳定性考察以及不确定度评估。结果表明,加替沙星纯度标准物质的纯度值为93.1%,扩展不确定度为0.6%(k=2),水分含量为6.6%,特性量值均匀性良好,6个月稳定性可靠,被认定为国家二级标准物质,编号为GBW(E) 100476。研制的加替沙星纯度标准物质填补了国内空白,同时也为吸湿性较强的药物纯度标准物质研制过程中水分测定提供了参考与借鉴。     

Development of a certified reference material for lead in noodles powder

Accreditation and Quality Assurance - Food Safety and Standards Authority of India has set maximum permissible level of lead in noodle at 2.5 mg/kg. The standardized lead measurement is of high...     

Certified reference material for quantification of polycyclic aromatic hydrocarbons in sediment from the National Metrology Institute of Japan

The National Metrology Institute of Japan has issued a certified reference material (CRM) of freshwater lake sediment for polycyclic aromatic hydrocarbon (PAHs) analyses. The certification used three extraction techniques: pressurized liquid extraction (PLE) with toluene, PLE with dichloromethane/ethyl acetate (1:1 by volume), and alkaline extraction (1 M KOH in methanol) in combination with microwave-assisted extraction. Both gas chromatography/mass spectrometry (GC/MS) and liquid chromatography/dopant-assisted atmospheric pressure photoionization/MS (LC/DA-APPI/MS) analyses were used. Certified values are provided for 18 PAHs at 1–25 μg kg⁻¹ except for perylene (2.08 × 10³ μg kg⁻¹), and information values are provided for two. Since the values of PAHs in the CRM are much lower than those in other CRMs and are comparable to those found at sites with little human influence, the CRM is suitable for PAH monitoring in sediment and soil samples.     

Development of a certified reference material for the determination of perfluorooctanoic acid

A certified reference material (CRM) for the determination of perfluorooctanoic acid (PFOA) has been issued as NMIJ CRM 4056-a by the National Metrology Institute of Japan, National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). Purity (kg kg^?1) based on a titration method was determined by subtracting the mass fractions of impurities measured using liquid chromatography/mass spectrometry (LC/MS) from those of acids expressed as PFOA measured by a neutralization potentiometric titration. To validate an obtained result, purity based on a mass balance method was determined by subtracting the mass fractions of impurities, measured using LC/MS, Karl-Fischer titration (KFT), and vacuum evaporation, from 1 kg kg^?1. Results from both titration and mass balance methods were in agreement within the accepted limits of uncertainty. The certified purity of NMIJ CRM 4056-a was determined to be 0.959 kg kg^?1, calculated as the mean of the results obtained with the two methods. The standard uncertainty of the certified purity was evaluated from purity evaluations as well as from sample homogeneity and stability obtained from LC/MS and KFT analyses. Consequently, the expanded uncertainty was estimated to be 0.005 kg kg^?1 with a coverage factor of k = 2.     

Development of bovine serum albumin certified reference material

We present the development process for National Institute of Metrology (NIM) bovine serum albumin (BSA) certified reference material (CRM). Each CRM unit contains about 200 mg of purified BSA. The moisture, ignition residue, molecular weight, and high-performance liquid chromatography (HPLC) purity were analyzed and mass spectrometry based protein identification was carried out to ensure the material was BSA. Both amino acid based isotope dilution mass spectrometry (IDMS) and a purity deduction method were selected for value assignment. The certified value was the average of the IDMS and the purity deduction result. HPLC purity analysis was used to examine the homogeneity and stability of solid BSA CRM. Fifteen units were selected for between-bottle homogeneity examination and seven subsamples from the same bottle were selected for within-bottle homogeneity examination. Statistics showed the CRM passed both the between-bottle and the within-bottle homogeneity examination. The CRM stability under storage conditions (-20 °C) was tested for 18 months and no trend was observed. Uncertainties from the balance, amino acid purity, hydrolysis, method reproducibility, homogeneity, and stability were taken into account in uncertainty evaluation. The final certified value of NIM BSA CRM is (0.963±0.038) g/g.     

Microheterogeneity evaluation of polycyclic aromatic hydrocarbons in particulate standard reference materials

With the emergence of highly sensitive analytical techniques, the microanalysis of natural-matrix materials employing smaller sample sizes is increasingly more common, which subsequently warrants a homogeneity assessment for the individual components at the appropriate sampling level. Pressurized liquid extraction (PLE) in combination with gas chromatography/mass spectrometry (GC/MS) has been used to determine the sampling constants and evaluate the relative homogeneity of trace levels of polycyclic aromatic hydrocarbons (PAHs) for two previously certified particulate standard reference materials, SRM 1649a Urban Dust and SRM 1650b Diesel Particulate Matter, in the milligram sampling range. Fluoranthene, pyrene, benz[a]anthracene and benzo[e]pyrene within SRM 1650b Diesel Particulate Matter were deemed to be homogeneous, based on relatively small sampling constants (K _S<100 mg), whereas the larger sampling constants (K _S>100 mg) obtained for all PAHs in SRM 1649a Urban Dust suggest more material heterogeneity. The material heterogeneity of ten individual PAHs (phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, benzo[k]fluoranthene, benzo[e]pyrene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene and benzo[ghi]perylene) was also described via nonlinear relationships (i.e., power law) between subsampling error S _s (%) and sample mass, which are used to predict analyte-specific minimum sample masses that result in a specific level of analytical uncertainty. Electronic supplementary material Supplementary material is available for this article at and is accessible for authorized users.     

Micellar microwave-assisted extraction combined with solid-phase microextraction for the determination of polycyclic aromatic hydrocarbons in a certified marine sediment

A method for the determination of polycyclic aromatic hydrocarbons (PAHs) in marine sediments using microwave-assisted extraction with a micellar medium combined with solid-phase microextraction (SPME) and gas chromatography-mass spectrometry (GC-MS) has been developed. Two kinds of SPME fibers (100 μm polydimethylsiloxane and 85 μm polyacrylate) and different micellar media were compared for the extraction efficiency of the 16 EPA priority PAHs. The polyacrylate fiber with a micellar medium of polyoxyethylene-10-laurylether provides the highest extraction efficiency. The method is remarkable for presenting lower equilibrium times and considerably higher reproducibilities than the obtained in aqueous medium. The LODs obtained ranged between 0.28 ng/ml for fluorene and 7.66 ng/ml for indeno[1,2,3-cd]pyrene. The method has been applied to the determination of PAHs in a certified marine sediment (SRM 1941a), obtaining recoveries between 58.6 and 111.5% for three- to five-ring PAHs with precision close to or lower than the certified values.     

Partitioning study of polycyclic aromatic hydrocarbons between water and some selected water-insoluble phases

An investigation on the partitioning of naphthalene and phenanthrene between water and some water-insoluble phases has been carried out by Uv-vis-NIR spectrophotometry. The analysis of the experimental results emphasized the role of intermolecular interactions and structural features of the hosting phases as driving forces of the partitioning of these polycyclic aromatic hydrocarbons. The critical comparison of the resulting distribution constants allowed to evaluate the potentials of some extracting phases to set up sensitive analytical methods and/or effective environment remediation technologies.     

Production of certified reference material

Summary Carbon has been determined in 31 European reference steels in the range of 11–2561 g/g C, using an absolute calibration method.High-purity calcium carbonate was used as the calibration material and weighing was carried out by means of a balance with extremely small weighing error. Both synthetic calibration samples and test samples were processed alternatingly under identical conditions, and the analyses were completed in the shortest possible time.In 28 of the cases examined, results were lower than the certificate values, by an average of 27 g/g. The interval of uncertainty of the accuracy was 6 g/g (probability 99%).

---

Herstellung zertifizierter ReferenzmaterialienGenaue Bestimmung von Kohlenstoff in Stählen im Bereich von 11–2561g/g

Zusammenfassung Die Kohlenstoffgehalte von 31 europäischen zertifizierten Referenzstählen im Arbeitsbereich von 11–2561 g/g Kohlenstoff wurden durch absolute Eichung überprüft.Die hinreichende Reinheit des Eichmittels Calciumcarbonat wurde sichergestellt und ein Wägesystem mit einem hinreichend kleinen Wägefehler benutzt.Das gleiche Verhalten von synthetischen Eichproben und Analysenproben im Analysenprozeß wurde hergestellt und beide Probearten wechselweise unter konstanten Systembedingungen innerhalb kürzester Zeitspanne untersucht. In 28 der untersuchten Fällen wurden im Mittel um 27 ppm tiefere Werte gefunden als in den Zertifikaten angegeben. Das Unsicherheitsintervall der Richtigkeit der gefundenen Werte lag mit einer Wahrscheinlichkeit von 99% im Mittel bei 6 g/g.

---

Abbreviations CRM Certified reference material - ppm g/g The author thanks Mr. E. Weichert for his excellent direction of the practical work.     

Development of an analytical method for polycyclic aromatic hydrocarbons and their derivatives

Garlic and onion, are well known for their medical value, especially in against cancer and anticardiovacular diseases. "Alliins" (S-alk(en)yl-L-cysteine sulphoxides) are sources of major active compounds in Allium plants. Se incorporation into garlic significantly increases activities of garlic in cancer prevention and inhibition. Selenomethionine, selenocysteine and Se-methylselenocysteine have been identified in garlic and onion. Previously we identified gamma-glutamyl-Se-methyl-L-selenocysteine, in extracts of garlic cultivated in Se-rich soil [Med. Res. Rev. 16 (1) (1996) 111], suggesting the possible existence of Se-alk(en)yl-L-cysteine selenoxides (Se-"alliins") in garlic. Several comparative experiments were carried out to demonstrate the existence of Se-"alliins" in Se-enriched garlic and onion. We found that there was one similar time-dependent Se signal in HPLC-inductively coupled plasma MS chromatograms of cold-water extracts of freeze-dried garlic powder and fresh garlic. This signal was lost when the extracts of garlic powder and fresh garlic were stored for 1 day at >4 degrees C, but remained in fresh onion extract at the same storage conditions. These phenomena and possible mechanisms are discussed. An additional experiment showed that Allium species cultivated in Se-rich soil might contain two different Se-"alliins".