Uncertainty of inductively coupled plasma mass spectrometry based measurements: an application to the analysis of urinary barium, cesium, antimony and tungsten

The wide use of barium (Ba), cesium (Cs), antimony (Sb) and tungsten (W) in many industrial and agricultural fields causes the increased release of these metals into the environment, laying the basis for health risk. To assess the exposure for the general population, the development of adequate and reliable analytical techniques becomes compulsory. This study refers to the quantification of urinary Ba, Cs, Sb and W levels by both quadrupole (Q) and sector field (SF) inductively coupled plasma mass spectrometry (ICP-MS). The two procedures were compared for their performances and their measurement uncertainties. The limits of detection were (Q and SF) 23.0 and 5.21 ng L(-1) for Ba; 21.1 and 7.52 ng L(-1) for Cs; 1.09 and 0.43 ng L(-1) for Sb; and 0.36 and 0.49 ng L(-1) for W. The trueness was better than 93.3% and the precision less than 12% for both techniques. Relative expanded uncertainties of the analytical procedures, at the median levels found in the general population, were below 5% for all the elements with both ICP-MS techniques. The uncertainties related to the calibration and repeatability were the parameters most influencing the final analytical performance. The urinary median values observed in healthy subjects from central Italy were 1146, 4301, 60.8 and 48.5 ng L(-1) for Ba, Cs, Sb and W, respectively.     

ICP-MS determination of Pt in biological fluids of patients treated with antitumor agents: evaluation of analytical uncertainty

The estimation of the uncertainty associated to the analytical methods is necessary in order to establish the comparability of results. Methods of Pt determination in biological fluids lack very often of information about uncertainty of results, with likely implications when results are used to interpret the mechanism of action of platinum compound or when they are considered to optimise the clinical therapies.An inductively coupled plasma-mass spectrometer (ICP-MS) method for the determination of Pt in biological fluids (plasma, ultrafiltrate and urine) of patients treated with antitumor agents has been developed and validated. The limits of quantification (LOQ) in the three matrices were 1.0, 0.1, and 2.0 μg/l, respectively.Intraday and interday precisions and accuracies were in good agreement with the FDA criteria for the validation of analytical methods. The validation study was implemented by assessing the uncertainty evaluation for Pt determination in the different matrices according to EURACHEM/CITAC Guide.     

Highly sensitive routine method for urinary 3-hydroxybenzo[a]pyrene quantitation using liquid chromatography-fluorescence detection and automated off-line solid phase extraction

Many workers and also the general population are exposed to polycyclic aromatic hydrocarbons (PAHs), and benzo[a]pyrene (BaP) was recently classified as carcinogenic for humans (group 1) by the International Agency for Research on Cancer. Biomonitoring of PAHs exposure is usually performed by urinary 1-hydroxypyrene (1-OHP) analysis. 1-OHP is a metabolite of pyrene, a non-carcinogenic PAH. In this work, we developed a very simple but highly sensitive analytical method of quantifying one urinary metabolite of BaP, 3-hydroxybenzo[a]pyrene (3-OHBaP), to evaluate carcinogenic PAHs exposure. After hydrolysis of 10 mL urine for two hours and concentration by automated off-line solid phase extraction, the sample was injected in a column-switching high-performance liquid chromatography fluorescence detection system. The limit of quantification was 0.2 pmol L(-1) (0.05 ng L(-1)) and the limit of detection was estimated at 0.07 pmol L(-1) (0.02 ng L(-1)). Linearity was established for 3-OHBaP concentrations ranging from 0.4 to 74.5 pmol L(-1) (0.1 to 20 ng L(-1)). Relative within-day standard deviation was less than 3% and relative between-day standard deviation was less than 4%. In non-occupationally exposed subjects, median concentrations for smokers compared with non-smokers were 3.5 times higher for 1-OHP (p<0.001) and 2 times higher for 3-OHBaP (p<0.05). The two urinary biomarkers were correlated in smokers (ρ=0.636; p<0.05; n=10) but not in non-smokers (ρ=0.09; p>0.05; n=21).     

Uncertainty evaluation in the analysis of biological samples by sector field inductively coupled plasma mass spectrometry. Part A: measurements of Be,Cd, Hg,Ir, Pb,Pd, Pt,Rh, Sb,U, Tl and W in human serum

A protocol that utilises data (trueness/recovery, precision and robustness) from validation tests to calculate measurement uncertainty was described and applied to a sector field inductively coupled plasma mass spectrometry (SF‐ICP‐MS)‐based method for the determination of Be, Cd, Hg, Ir, Pb, Pd, Pt, Rh, Sb, U, Tl and W in human serum. The method was validated according to criteria issued by international bodies such as AOAC, Eurachem and ISO and the uncertainty in the analytical measurements was estimated following the Eurachem/Citac guide. The methodology was based on dilution of human serum with water and analysis by serum‐matched standard calibration. The method quantification limits ranged 0.02 µg/L (Tl, Ir) to 0.26 µg/L (Hg). The coefficients of regression were greater than 0.9991 over a range of two orders of magnitude of concentration. The mean trueness was 101% and the mean recovery on three levels of fortification (1‐, 1.5‐, and 2‐times the baseline serum level) ranged between 93.3% and 106%. The maximum relative standard deviation values for repeatability and within‐laboratory reproducibility were 12.8% and 13.5%. The method was robust to slight variations of some critical factors relevant to the sample preparation and SF‐ICP‐MS instrumentation. The relative expanded uncertainty over three levels of concentration ranged from 11.6% (Hg) to 27.6% (Pt), and the uncertainty on the within‐laboratory reproducibility, which included factors such as time, analyst and calibration, represented the main contribution to the overall uncertainty. Copyright © 2010 John Wiley & Sons, Ltd.     

Method for the determination of thorium and uranium in urine by ICP-MS

ICP-MS (inductively coupled plasma mass spectrometry) is shown as a very sensitive method for quantitative determination of Th and U concentration and excretion analysis in urine without any sample pretreatment. The current standard method for incorporation monitoring applies alpha-spectrometry, a very tedious and time consuming technique. ICP-MS offers an attractive alternative for monitoring of thorium and uranium body burdens in occupationally exposed subjects and also larger groups of the general population. A limit of determination of 0.5 ng/L in aqueous solutions and 1 ng/L in urine samples for both elements was achieved, with a precision of about ± 10% in the concentration range of appr. 10 ng/L. Due to the lack of a suitable reference material, the accuracy of the method was tested by comparing some of the results with those obtained by -spectrometry, especially for U. There was a sufficient agreement on both results.     

Determination of chloroplatinates by CE coupled to inductively coupled plasma sector field MS

In the present work the degradation of chloroplatinates emitted into the aquatic environment has been investigated in model studies. CE coupled to inductively coupled plasma sector field MS (ICP-SFMS) was employed as an analytical method of measurement. The CE-ICP-MS interface utilized the functional make-up flow design with a microconcentric nebulizer. [Pt(Cl(4))](2-) and [Pt(Cl(6))](2-) were separated within 5 min. During a measurement period of 6 h an excellent reproducibility of migration times (RSD 2.3%) could be achieved. The high sensitivity of ICP-SFMS resulted in an LOD of 80 ng/L platinum for the two compounds. External calibration using rhenium as internal standard was linear over three orders of magnitude. However, with external calibration a long-term drift of signal intensity was observed. In order to reduce the uncertainty of the obtained results, quantification of [PtCl(6)](2-) was performed for the first time by species-specific on-line isotope dilution MS using (194)[PtCl(6)](2-) as spike. The two different quantification strategies were compared in terms of their total combined uncertainty of measurement according to the EURACHEM guideline. The method was employed for monitoring the time-dependent degradation of [Pt(Cl(4))](2-) and [Pt(Cl(6))](2-) in water containing 0 and 2.8 mmol/L Cl(-) and river water. [Pt(Cl(6))](2-) was stable whereas [Pt(Cl(4))](2-) showed rapid degradation following pseudo first-order kinetics.     

Open-channel chip-based solid-phase extraction combined with inductively coupled plasma-mass spectrometry for online determination of trace elements in volume-limited saline samples

In this study, we used an automated online chip-based solid-phase extraction (SPE)-inductively coupled plasma-mass spectrometry (ICP-MS) system for analyzing trace elements in small-volume saline samples (～15 μL). The proposed method involved the adsorption of trace metal ions in the interior of a functionalized poly(methyl methacrylate) (PMMA) channel in order to separate these ions from saline matrices. The adsorption of transition metal ions was presumably dominated by the surface complexation between the carboxylate moieties in the interior of the PMMA channel and the metal ions, which facilitated the formation of metal-carboxylate complexes. The components of the proposed online analytical system used for the simultaneous detection of multiple trace metals in saline samples involved microdialysis (MD) sampling, an established chip-based SPE procedure, and ICP-MS. The SPE-ICP-MS hyphenated system was optimized, and then, the analytical reliability of this system was further confirmed by using it to analyze the certified reference materials-SRM 2670 (human urine) and SRM 1643e (artificial saline water). The satisfactory analytical results indicated that the proposed on-chip SPE device could be readily used as an interface for coupling the MD probe with the ICP-MS system. The dramatically reduced consumption of chemicals and "hands-on" manipulations enabled the realization of a simplified and relatively clean procedure with extremely low detection limits in the range of 5.86-76.91 ng L(-1) for detecting Mn, Co, Ni, Cu, and Pb in 15-μL samples by ICP-MS. The effectiveness of an online MD-chip-based SPE-ICP-MS technique for continuous monitoring of trace elements in a simulated biological system was also demonstrated. To the best of our knowledge, this is the first paper to report the direct exploitation of a PMMA chip as an SPE adsorbent for online sample pretreatment and trace metal preconcentration prior to ICP-MS measurement.     

Determination of platinum group elements and gold in geological materials: a review of recent magnetic sector and laser ablation applications

Inductively coupled plasma mass spectrometry (ICP-MS) has been used extensively as a rapid and accurate instrumental technique for determinations of platinum group elements (PGEs) and gold. Methods based upon ICP-MS have been important in analyses of many types of samples, and especially of geological materials containing very low concentrations of these elements. Recently, analytical methods based upon ICP-MS have been improved and widened in scope by the introduction of new magnetic sector (or high resolution) spectrometers, and laser ablation (LA) sampling. Detection limits attainable for PGEs and Au using magnetic sector instruments in analytical procedures cited here are as low as 0.01-0.02 pg g⁻¹; instruments have a dynamic range of up to nine orders of magnitude. This review describes applications of the techniques to analyses of PGEs and gold in minerals, nodules, meteorites, ice, sediments, airborne particulates and reference materials. The period covered is 1998-2002.     

Displacement solid-phase extraction on mercapto-functionalized magnetite microspheres for inductively coupled plasma mass spectrometric determination of trace noble metals

A flow injection online displacement solid-phase extraction (DSPE) via magnetic immobilization of mercapto-functionalized magnetite microspheres onto the inner walls of a knotted reactor (KR) coupled with inductively coupled plasma mass spectrometry was developed for selective preconcentration and determination of trace noble metals (Ru, Rh, Pd, Pt, Ir and Au) in complex matrices. Online DSPE of 2.7 mL aqueous solution gave the enhancement factors of 32-46 for the six noble metals in comparison with direct nebulization of aqueous sample solution, and the detection limits (3 s) of 2.1 ng L(-1) for Ru, 1.9 ng L(-1) for Rh, 2.5 ng L(-1) for Pd, 1.8 ng L(-1) for Ir, 1.9 ng L(-1) for Pt and 1.7 ng L(-1) for Au. The sample throughput of the developed method was about 20 samples h(-1), and the relative standard deviation for eleven replicate determinations of the noble metals at the 30 ng L(-1) level ranged from 1.2% to 2.1%. The recoveries of Ru, Rh, Pd, Pt, Ir and Au still maintained 90% even after successive 140 cycles of DSPE. The developed method was successfully applied to selective determination of trace Ru, Rh, Pd, Pt, Ir and Au in complex matrices.     

On the re-assessment of the optimum conditions for the determination of platinum, palladium and rhodium in environmental samples by electrothermal atomic absorption spectrometry and microwave digestion

The experimental conditions for the determination of platinum, palladium and rhodium by graphite furnace atomic absorption spectrometry (GFAAS) are re-assessed. A certified material (BCR-723) was used as a working sample and analyzed using various extraction and atomization procedures in order to find the optimal experimental conditions that enable the quantitative and reproducible detection of platinum, palladium and rhodium in environmental matrices. Evidently, literature observations regarding the atomization conditions were proven fairly adequate. However, the provision of the optimum extraction conditions revealed several parameters that lie behind the reported uncertainties. The appropriate combination between extraction conditions and atomization programs afforded a considerable improvement in the recoveries and analytical features of platinum, palladium and rhodium determination with GFAAS. Cross-examination of the analytical data with various CRMs (certified reference materials) was used to validate the robustness of the method in heterogeneous matrices bearing different element levels. Under the optimum experimental conditions the method permits the determination at concentrations as low as (LOD(3S/N)) 1.9 ng g(-1), 0.45 ng g(-1) and 0.6 ng g(-1) for Pt, Pd and Rh, respectively affording recoveries in the range of 93-101%. The method was successfully applied to the assessment of Pt, Pd and Rh accumulation in real road dust and soil samples in Greece.     

On the Use of ICP-MS for Measuring Plutonium in Urine

The analytical protocols currently used to measure plutonium in urinary excretion consist of radiochemical purification, the source preparation by electroplating and alpha spectrometry measurements. Such a procedure is of limited relevance to the individual monitoring of workers exposed to plutonium and mixed oxides. The use of ICP-MS, which takes much shorter counting time, was investigated with the aim of assessing the capabilities of this analytical tool for the determination of urinary excretion of plutonium. It has been shown that the detection level of 1 mBq·1^-1 could be achieved after a radiochemical purification process for a standard ICP-MS set-up.     

Microwave-assisted solid phase extraction prior to ICP-MS determination of Pd and Pt in environmental and biological samples

A sensitive and selective microwave-assisted solid phase extraction procedure coupled to inductively coupled plasma-mass spectrometry (ICP-MS) is proposed for palladium (Pd) and platinum (Pt) quantification in environmental and biological samples. Pd and Pt were quantitatively retained on commercial thioureido propyl functionalised silica gel packed inside a home-made glass microcolumn, and later eluted with 0.5% thiourea solution under microwave irradiation, followed by ICP-MS determination. The main variables affecting the procedural stages (i.e., sorption and desorption) and ICP-MS determination were optimised. The best conditions found were: (a) sorption: sample acidity, 1?M HCl; sample flow rate, 3?mL?min^?1; (b) desorption: microwave radiation, power 800?W; eluent concentration, 0.5% thiourea; eluent flow rate, 0.5?mL?min^?1; (c) ICP-MS determination: nebuliser feeding, free aspiration (0.3?mL?min^?1); internal standard, Rh (5?µg?L^?1). Analyte recoveries were higher than 90% and concentration factors up to 90 and 92 were achieved for Pd and Pt, respectively. Depending on the conditions, the methodological limits of detection were down to 0.2?ng?L^?1 for both analytes and repeatability, expressed as RSD%, varied between 1.3 and 11.0%. A method selectivity evaluation showed that most of the ICP-MS interferents were either quantitatively separated or more than 86% eliminated, except for Cu (elimination efficiency around 30%). Finally, the method was successfully used to determine Pd in certified reference materials (i.e. human urine and serum) and Pd and Pt in PM₁₀ airborne particulate matter fractions.     

Simplified method for the determination of Ru, Pd, Re, Os, Ir and Pt in chromitites and other geological materials by isotope dilution ICP-MS and acid digestion

A method for the determination of low Ru, Pd, Re, Os, Ir and Pt abundances in geological reference materials by isotope dilution inductively coupled plasma mass spectrometry (ICP-MS) after acid digestion in a high pressure asher (HPA-S) is presented. The digestion technique is similar to that using Carius tubes but easier to handle and reaches higher temperatures. Osmium can be determined as OsO4 with ICP-MS directly after digestion through a sparging technique. The remaining elements are preconcentrated by means of anion column chromatography. The resin is digested directly without elution leading to high yields but this causes problems if Zr is present at higher levels in the silicate rich materials. The analytical results for international platinum group element (PGE) reference materials, chromitite CHR-Bkg, basalt TDB-1 and gabbro WGB-1, are presented and compared with literature data, demonstrating the validity of the described method. Although higher in concentration, PGEs determined for reference material WGB-1 were worse than for TDB-1 indicating a more inhomogeneous distribution of the platinum group mineral phases. The low PGE abundance chromitite standard, CHR-Bkg, is likely to be homogeneous for Ru, Re, Os and Ir and is recommended as a reference material for the study of chromitites. Detection limits (3s x total procedure blank) range from 0.012 ng (Re and Os) to 0.77 ng (Pt), which could be further improved by applying higher quality acids.     

Slurry sampling for the determination of arsenic, cadmium, and lead in mainstream cigarette smoke condensate by graphite furnace–atomic absorption spectrometry and inductively coupled plasma–mass spectrometry

The slurry sampling technique has been applied for the determination of As, Cd, and Pb in mainstream cigarette smoke condensate (MS CSC) by graphite furnace-atomic absorption spectrometry (GF-AAS) and inductively coupled plasma-mass spectrometry (ICP-MS). The MS CSC of the 1R4F Reference Cigarette was collected by electrostatic precipitation and was subsequently prepared as two slurry samples with and without the dispersing agent Triton X-100. Comparison of results determined by ICP-MS analyses of the 1R4F MS CSC slurry samples with those from the conventional microwave digestion method revealed good agreement. The precision of Triton X-100 slurry sampling and of microwave-assisted digestion was better than 10% RSD, and both were superior to slurry sampling without use of Triton X-100. The accuracy of the analytical results for the Triton X-100 slurry sample was further verified by graphite furnace-atomic absorption spectrometry (GF-AAS). For GF-AAS, the method limits of detection are 1.6, 0.04, and 0.5 microg x L(-1) for As, Cd, and Pb, respectively. For ICP-MS, the method limits of detection are 0.06, 0.01, and 0.38 microg x L(-1) for As, Cd, and Pb, respectively. The MS CSC of the 1R4F Reference Cigarette was collected in accordance with the Federal Trade Commission (FTC) smoking regime (35 mL puff volume of 2-s puff duration at an interval of 60 s) and the concentrations of As, Cd and Pb were 6.0+/-0.5, 69.3+/-2.8, and 42.0+/-2.1 ng/cigarette, respectively.     

Multi-element determination in earthworms with instrumental neutron activation analysis and inductively coupled plasma mass spectrometry: A comparison

Earthworms were collected from agricultural fields in Admont, Graz, Piber and Gumpenstein, Austria. Six earthworm samples were investigated with INAA and with ICP-MS in parallel for the element concentrations of As, Ba, Cd, Co, Cr, Cu, Fe, Hg, Pb, Rb, Sb, Se and Zn. With both techniques 14 elements were analysed in a wide concentration range (ng/g to mg/g) GF-AAS and HG-AAS were used for verification of some element concentrations. A comparison of analytical results between INAA and ICP-MS was discussed. In general, good agreement between ICP-MS and INAA was obtained, the relative difference values of most of the elements are within ±20% range, however, a methodical error for the determination of Hg by ICP-MS was found.     

Determination of dichloroanilines in human urine by gas chromatography/mass spectrometry: validation protocol and establishment of Reference Values in a population group living in central Italy

3,4- and 3,5-Dichloroanilines (DCAs) are common markers of some non-persistent pesticides, e.g. linuron, diuron, vinclozolin, and iprodione. The general population may be exposed to these DCAs and/or their precursors mainly through diet. Since adverse effects on human health, such as endocrine disruption, have been reported, biological monitoring is essential for exposure assessment both of occupationally exposed subjects and of the general population. A highly sensitive and selective gas chromatography/mass spectrometry (GC/MS) method has been developed for the determination of 3,4- and 3,5-DCAs in urine using 4-chloro-2-methylaniline as an internal standard. The selected ion monitoring (SIM) mode was employed for quantitation of the analytes. The sample treatment procedure is simple and fast and no derivatization is required. The overall method was validated including uncertainty measurement. The limit of detection (LOD) and the lower limit of quantitation (LLOQ) were determined to be 0.005 and 0.010 microg/L for both analytes. The method was then applied to the establishment of reference values for a population group living in a rural area of central Italy (Novafeltria, Marche). A total of 151 out of 153 samples were found to be positive for 3,5-DCA, and 81.7% were positive for 3,4-DCA. For this group, 3,4-DCA levels ranged from 0.01 to 6.19 microg/L, while 3,5-DCA urinary concentrations were between 0.02 and 6.71 microg/L.     

SI-traceable certification of the amount content of cadium below the ng g(-1) level in blood samples by isotope dilution ICP-MS applied as a primary method of measurement

The development and implementation of a method for the certification of cadmium in blood samples at low ng g(-1) and sub ng g(-1) levels is described. The analytical procedure is based on inductively coupled plasma isotope dilution mass spectrometry (ICP-IDMS) applied as a primary method of measurement. Two different sample digestion methods, an optimized microwave digestion procedure using HNO3 and H2O2 as oxidizing agents and a high-pressure asher digestion procedure, were developed and compared. The very high salt content of the digests and the high molybdenum content, which can cause oxide-based interferences with the Cd isotopes, were reduced by a chromatographic matrix separation step using an anion-exchange resin. All isotope ratio measurements were performed by a quadrupole ICP-MS equipped with an ultrasonic nebulizer with membrane desolvator. This sample introduction set-up was used to increase sensitivity and minimize the formation of oxides (less MoO+ interference with the Cd isotopes). Because of the very low Cd concentrations in the samples and the resulting need to minimize the procedural blank as much as possible, all sample-processing steps were performed in a clean room environment. Detection limits of 0.005 ng g(-1) Cd were achieved using sample weights of 2.7 g. The method described was used to recertify the cadmium content of three different blood reference materials from the Community Bureau of Reference (BCR) of the European Commission (BCR-194, BCR-195, BCR- 196). Cadmium concentrations ranged between approximately 0.2 ng g(-1) and approximately 12 ng g(-1). For these materials, SI-traceable certified values including total uncertainty budgets according to ISO and Eurachem guidelines were established.     

Reference values of urinary 3,5,6-trichloro-2-pyridinol in the Italian population--validation of analytical method and preliminary results (multicentric study)

The interlaboratory validation of analytical procedures for the assay of urinary 3,5,6-trichloro-2-pyridinol (TCP) in the general Italian population is reported. The determinations were performed by high-resolution gas chromatography (HRGS) with electron capture detection and HRGS with mass spectrometry (MS) in 2 laboratories. The urine samples were from 42 participants from 3 regions of Italy. The results were evaluated by interlaboratory quality control. Urinary TCP concentrations were above the detection limit (1.2 micrograms/L) in 88% of the population, with a mean detectable concentration [GM (GSD)] of 2.8 (1.9) micrograms/g creatinine (creat). (GM, geometric mean; GSD, geometric standard deviation.) The Mann-Whitney U test showed that wine consumption was a statistically significant variable (p < 0.05) for urinary concentrations of TCP. Analysis of variance of the logarithm of urinary TCP versus wine consumption and diet showed a statistically significant fit. The model used explained 30% of the total variance: wine consumption and diet accounted for 37 and 17% respectively of the explained variance.     

Automated in situ trace element analysis of silicate materials by laser ablation inductively coupled plasma mass spectrometry

This paper describes the automated in situ trace element analysis of solid materials by laser ablation (LA) inductively coupled plasma mass spectrometry (ICP-MS). A compact computer-controlled solid state Nd:YAG Merchantek EO UV laser ablation (LA) system has been coupled with the high sensitivity VG PQII S ICP-MS. A two-directional communication was interfaced in-house between the ICP-MS and the LA via serial RS-232 port. Each LA-ICP-MS analysis at a defined point includes a 60 s pre-ablation delay, a 60 s ablation, and a 90 s flush delay. The execution of each defined time setting by LA was corresponding to the ICP-MS data acquisition allowing samples to be run in automated cycle sequences like solution auto-sampler ICP-MS analysis. Each analytical cycle consists of four standards, one control reference material, and 15 samples, and requires about 70 min. Data produced by Time Resolved Analysis (TRA) from ICP-MS were later reduced off-line by in-house written software. Twenty-two trace elements from four reference materials (NIST SRM 613, and fused glass chips of BCR-2, SY-4, and G-2) were determined by the automated LA-ICP-MS method. NIST SRM 610 or NIST SRM 613 was used as an external calibration standard, and Ca as an internal standard to correct for drift, differences in transport efficiency and sampling yield. Except for Zr and Hf in G-2, relative standard deviations for all other elements are less than 10%. Results compare well with the data reported from literature with average limits of detection from 1 ng x g(-1) to 455 ng x g(-1) and less than 100 ng x g(-1) for most trace elements.     

Mononuclear (Pd, Pt), heterodinuclear (PdAg, PtAg), and tetranuclear (Pd2Ag2, Pt2Ag2) 1,1-ethylenedithiolato complexes

lp;&-5q;1 The reactions of [Tl2[S2C=C[C(O)Me]2]]n with [MCl2L2] (1:1) or with [MCl2(NCPh)2] and PPh3 (1:1:2) give complexes [M[eta2-S2C=C[C(O)Me]2]L2] [M = Pt, L2 = 1,5-cyclooctadiene (cod) (1); L2 = bpy, M = Pd (2a), Pt (2b), L = PPh3, M = Pd (3a), Pt (3b)] whereas with MCl2 and QCl (2:1:2) anionic derivatives Q2[M[eta2-S2C=C[C(O)Me]2]2] [M = Pd, Q = NMe4 (4a), Ph3P=N=PPh3 (PPN) (4a'), M = Pt, Q = NMe4 (4b)] are produced. Complexes 1 and 3 react with AgClO4 (1:1) to give tetranuclear complexes [[ML2]2Ag2[mu2,eta2-(S,S')-[S2C=C[C(O)Me]2]2]](ClO4)2 [L = PPh3, M = Pd (5a), Pt (5b), L2 = cod, M = Pt (5b')], while the reactions of 3 with AgClO4 and PPh3 (1:1:2) give dinuclear [[M(PPh3)2][Ag(PPh3)2][mu2,eta2-(S,S')-S2C=C[C(O)Me]2]]]ClO4 [M = Pd (6a), Pt (6b)]. The crystal structures of 3a, 3b, 4a, and two crystal forms of 5b have been determined. The two crystal forms of 5b display two [Pt(PPh3)2][mu2,eta2-(S,S')-[S2C=C[C(O)Me]2]2] moieties bridging two Ag(I) centers.