Melt miscibility of HDPE/UHMWPE,LDPE/UHMWPE,and LLDPE/UHMWPE blends detected by dynamic rheometer

The dynamic rheological behavior of high density polyethylene (HDPE)/ultrahigh molecular weight polyethylene (UHMWPE) blends, low density polyethylene (LDPE)/UHMWPE blends and linear low density polyethylene (LLDPE)/ UHMWPE blends was measured in parallel plate rheometer at 200°C. The analysis of log-additivity rule, Cole-Cole plots and Han curves of the three series blends indicated that the LDPE/UHMWPE blends were miscible in the melt, while the HDPE/UHMWPE blends and LLDPE/UHMWPE blends showed phase separation. The DSC results of LLDPE/UHMWPE blends and HDPE/UHMWPE blends were consistent with the rheological properties, while for the thermal properties of LDPE/UHMWPE blends, results revealed three endothermic peaks, which indicated a liquid-solid phase separation in LDPE/UHMWPE blends.     

Thermal decomposition of polymethylmethacrylate synthesized with anionic catalysts

TG and DTA data are used to show that the thermal decomposition of polymethylmethacrylate (PMMA) synthesized with anionic catalysts depends on the nature of the catalyst. It is found that the thermal stability of PMMA obtained by using anionic amide catalysts is higher than that of radical PMMA and of PMMA obtained with other anionic catalysts, and depends on the temperature of polymerization and on the molecular weight of the polymer.     

IR and Py-GC/MS spectral simulation of polymer film by quantum chemical and quantum molecular dynamics calculations using the polymer models

We have simulated IR and pyrolysis gas chromatography mass spectrometry (Py-GCMS) spectra of six polymers (PE, PP, PS, PET, N6, PVDF) with the density-functional theory and quantum molecular dynamics calculations on model oligomers. In the former calculations, experimental harmonic frequencies of the polymers have been assigned from the simulated IR spectra. In the latter QMD calculations on thermal decomposition of polymer models, the approximated mass spectra of six (PE, PP, PS, PET, N6, PVDF) polymers were almost in good accordance with the experimental results in Py-GC/MS, although we adjusted the decomposition temperatures to 2240, 2520, and 2800 K as the average absolute deviation of 8%.     

Structure and spacing of cellulose microfibrils in woody cell walls of dicots

The structure of cellulose microfibrils in situ in wood from the dicotyledonous (hardwood) species cherry and birch, and the vascular tissue from sunflower stems, was examined by wide-angle X-ray and neutron scattering (WAXS and WANS) and small-angle neutron scattering (SANS). Deuteration of accessible cellulose chains followed by WANS showed that these chains were packed at similar spacings to crystalline cellulose, consistent with their inclusion in the microfibril dimensions and with a location at the surface of the microfibrils. Using the Scherrer equation and correcting for considerable lateral disorder, the microfibril dimensions of cherry, birch and sunflower microfibrils perpendicular to the [200] crystal plane were estimated as 3.0, 3.4 and 3.3 nm respectively. The lateral dimensions in other directions were more difficult to correct for disorder but appeared to be 3 nm or less. However for cherry and sunflower, the microfibril spacing estimated by SANS was about 4 nm and was insensitive to the presence of moisture. If the microfibril width was 3 nm as estimated by WAXS, the SANS spacing suggests that a non-cellulosic polymer segment might in places separate the aggregated cellulose microfibrils.     

Organelle sensor: amperometric determination of nadh by immobilized mitochondrial electron transport particles

A new sensor for NADH was developed by making use of an immobilized subcellular organelle. Mitochondria was used as a model system for assembling an organelle sensor. Mitochondrial electron transport particles (ETP) were prepared from beef heart muscle and entrapped in the membrane formed of agar gel. The membrane-bound ETP was found capable of NADH oxidation: $$NADH + \tfrac{1}{2}O_2 + H^ + \xrightarrow{{ETP}}NAD^ - + H_2 O$$ The membrane was tightly attached to the surface of an oxygen electrode capable of amperometric detection of O2. The sensor responded to NADH in solution with a resulting electric output. The response was enhanced by the addition of 2,4-dinitrophenol (DNP). NADH was determined in the concentration range 1–300 µM. NADH was alternatively determined for 2 weeks without replacing the ETP-bound membrane.     

A sensor based on incorporating Ni2+ into ZnO nanoparticles-multi wall carbon nanotubes-poly methyl metacrylat nanocomposite film modified carbon paste electrode for determination of carbohydrates

The ZnO nanoparticles (ZnONPs) were synthesized with gelatin as stabilizer via the sol-gel method and were characterized by transmission electron microscope (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). An electrochemical sensor based on ZnO nanoparticles-multi wall carbon nanotubes-poly methyl metacrylat (ZnONPs-MWCNT-PMMA) composite film was developed by incorporating Ni²⁺ into the ZnONPs-MWCNT-PMMA film modified carbon paste electrode (Ni²⁺/ZnONPs-MWCNT-PMMA/CPE). The electrochemical activity of Ni²⁺/ZnONPs-MWCNT-PMMA/CPE was illustrated in 0.10 M NaOH using cyclic voltammetry. The Ni²⁺/ZnONPs-MWCNT-PMMA/CPE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple. Ni²⁺/ZnONPs-MWCNT-PMMA/CPE also show good electrocatalytic activity toward the oxidation of carbohydrates (glucose, fructose and sorbitol). The Ni²⁺/ZnONPs-MWCNT-PMMA/CPE gives a good linear range with a detection limit of 8, 6, and 9 μM towards the determination of glucose, fructose and sorbitol, respectively by amperometry. Furthermore, the modified sensor was successfully applied to the sensitive determination of carbohydrates in real samples.     

Electroactive shape memory effect of radiation cross-linked SBS/LLDPE composites filled with carbon black

The poly(styrene-b-butadiene-b-styrene) (SBS) triblock copolymer and linear low-density polyethylene (LLDPE) were blended and irradiated by γ rays to prepare shape memory polymer (SMP). Different weight fractions of conductive carbon black (CB) were filled into SMP to form a novel electroactive shape memory CB/SBS/LLDPE composite. The CB reinforced radiation cross-linked SBS/LLDPE blends for the improvement of the mechanical weakness and conductivity of SBS/LLDPE bulk and for wide practical engineering uses. The electroactive shape memory CB/SBS/LLDPE composites were investigated by electrical properties, mechanical, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and electroactive shape memory effects. It is found that the tensile strength, storage modulus, and resistance against mechanical and thermal mechanical cycle loading in the developed composites increased due to the role of reinforcement of CB. The melting temperatures and volume resistance of the composites decreased with the increment of CB for excellent electrical conductivity of CB. The electroactive shape memory effects of developed CB/SBS/LLDPE composites were affected by CB weight fractions and applied voltage, while good shape recovery could be obtained in the shape recovery test. When the CB fraction is more than 5 wt%, full recovery can be observed after tens of seconds and shape recovery speed increased with CB fractions and voltage increasing. However, the shape recovery rate decreases slightly with increment of cycle times.     

Effect of Cl substituent in the aromatic tetracycline ring on its reactivity with solvated electrons

Decomposition yields of tetracycline hydrochloride /TC.HCl/ and chlorotetracycline hydrochloride /ClTC?HCl/ in methanol solution saturated with Ar or N₂O were determined. Rate constants of the reaction e_s with some antibiotics were obtained: $$\begin{gathered} k/e_s^ - + ClTC \cdot HCl/ = 2 \cdot 49 \times 10^8 dm^3 \cdot mole^{ - 1} \cdot s^{ - 1} ; \hfill \\ k/e_s^ - + TC \cdot HCl/ = 2 \cdot 86 \times 10^8 dm^3 \cdot mole^{ - 1} \cdot s^{ - 1} \cdot \hfill \\ \end{gathered} $$ On the basis of the diffence between decomposition yields: ΔG=G_?TC.HCl^?G?ClTC.HCl′ 7-C?Cl group decomposition yield and the rate constant $$k/e_s^ - + Cl - C - 7/ = 7 \cdot 94 \times 10^8 dm^3 \cdot mole^{ - 1} \cdot s^{ - 1} $$ were determined. It was demonstrated by¹H NMR that the radical formed by degradation of 7-C?Cl group is recombined with the H atoms leading to ClTC.HCl being converted into tetracycline hydrochloride /TC.HCl/.     

The IUPAC aqueous and non-aqueous experimental pKa data repositories of organic acids and bases

Accurate and well-curated experimental pKa data of organic acids and bases in both aqueous and non-aqueous media are invaluable in many areas of chemical research, including pharmaceutical, agrochemical, specialty chemical and property prediction research. In pharmaceutical research, pKa data are relevant in ligand design, protein binding, absorption, distribution, metabolism, elimination as well as solubility and dissolution rate. The pKa data compilations of the International Union of Pure and Applied Chemistry, originally in book form, have been carefully converted into computer-readable form, with value being added in the process, in the form of ionisation assignments and tautomer enumeration. These compilations offer a broad range of chemistry in both aqueous and non-aqueous media and the experimental conditions and original reference for all pKa determinations are supplied. The statistics for these compilations are presented and the utility of the computer-readable form of these compilations is examined in comparison to other pKa compilations. Finally, information is provided about how to access these databases.     

On the determination of HCl+ (A,v′) vibrational populations from HCl+ (A→X) fluorescence spectra: direct comparison between photoionization and penning ionization

Using a beam apparatus, we have measured the HCl⁺ (A,v′→X,v″) fluorescence spectra of HCl⁺ (A,v′) ions formed in HeI (58.4 nm), and NeI (73.6 nm) photoionization and, for the first time, in He (2³ S) Penning ionization under single collision conditions with a wavelength bandwidth around 1 nm. In addition, we have studied Ne (3s ³ P _{2, 0}) Penning ionization of HCl at three different collision energies. The procedure and the problems in extracting HCl⁺ (A,v′) vibrational populations from the data are discussed in some detail. Thedirect comparison of photoionization and Penning ionization data allows definitive conclusions to be drawn on the question whether final state interactions in the Penning reaction change the “nascent” vibrational population (determined by electron spectrometry); for He (2³ S)+HCl, such changes are shown to be absent within the experimental uncertainty (<±10%). For Ne (3s ³ P _{2, 0})+HCl, the HCl⁺ (A,v′=0, 1) populations are also found to be close to those measured by electron spectrometry and essentially independent of collision energy in the range 34–96 meV. From measurements of the fluorescence intensity as a function of HCl density, we have evidence for a fast loss of HCl⁺ (A,v′) ions in collisions with HCl (rate constant around 5·10^?9 cm³s^?1).     

Structural and thermal properties of HDPE/n-AlN polymer nanocomposites

High-density polyethylene (HDPE) containing various volume fractions (0–20 vol%) of aluminum nitride nanoparticles (n-AlN) is prepared by melt mixing. Structural and morphological characterizations of the prepared composites are carried out by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), and atomic force microscopy (AFM). Thermal stability and degradation kinetics of HDPE/AlN (nano) composites are investigated by Thermogravimetric analysis (TG). HR-TEM micrographs confirm fairly uniform dispersion of AlN nanoparticles, as well as the existence of long interconnected chain-like aggregates. AFM images also confirm homogeneous dispersion of n-AlN in the polymer matrix. Roughness analysis from the AFM data indicates the presence of substantial undulation from the mean surface level. Thermogravimetric data indicate small improvement in the thermal stability of the composites. Kinetic parameters, viz., the activation energy (E _a), frequency factor (A), and reaction order (n) are estimated using the isoconversional methods of Kissinger, Flynn–Wall–Ozawa (FWO), KAS, and Friedman. Activation energies (E _a) calculated by the above four models display nearly similar features and are enhanced by the presence of AlN nanoparticles. Kinetics of degradation of HDPE-AlN (nano) composites follows a first-order reaction.     

Low surface area carbonized silica obtained by the pyrolysis of dichloromethane: A column packing for adsorption and exclusion chromatography

Carbonized silica has been used as column packing for HPLC. Up to now it has been obtained by the pyrolysis of the vapour of benzene as well as aliphatic and aromatic alcohols. This paper reports on the properties of carbonized silica obtained by the pyrolysis of dichloromethane and used as column packing in HPLC.     

In Situ Characterization of Proteins Using Laserspray Ionization on a High-Performance MALDI-LTQ-Orbitrap Mass Spectrometer

The MALDI-LTQ-Orbitrap XL mass spectrometer is a high performance instrument capable of high resolution and accurate mass (HRAM) measurements. The maximum m/z of 4000 precludes the MALDI analysis of proteins without generating multiply charged ions. Herein, we present the study of HRAM laserspray ionization mass spectrometry (MS) with MS/MS and MS imaging capabilities using 2-nitrophloroglucinol (2-NPG) as matrix on a MALDI-LTQ-Orbitrap XL mass spectrometer. The optimized conditions for multiply charged ion production have been determined and applied to tissue profiling and imaging. Biomolecules as large as 15 kDa have been detected with up to five positive charges at 100 K mass resolution (at m/z 400). More importantly, MS/MS and protein identification on multiply charged precursor ions from both standards and tissue samples have been achieved for the first time with an intermediate-pressure source. The initial results reported in this study highlight potential utilities of laserspray ionization MS analysis for simultaneous in situ protein identification, visualization, and characterization from complex tissue samples on a commercially available HRAM MALDI MS system. Graphical Abstract

?     

Impact of PS/SiO2 morphologies on the SERS activity of PS/SiO2/Ag nanocomposite particles

To understand the relationship between the morphology of carboxyl-functionalized polystyrene/silica (PS/SiO₂) nanocomposite microspheres and the surface-enhanced Raman scattering (SERS) performance of PS/SiO₂/Ag nanocomposite particles, core-shell and raspberry-like PS/SiO₂ composite microspheres were used as templates to prepare PS/SiO₂/Ag nanocomposite particles. The core-shell and raspberry-like structured PS/SiO₂ templates were prepared via in situ sol-gel reaction by hydrolysis tetraethyl orthosilicate (TEOS) in alkali solution. Silver nanoparticles (10–50 nm) were loaded on the PS/SiO₂ templates’ surface by chemical reduction. The morphology and structure of the PS/SiO₂/Ag particles were characterized by TEM, SEM, X-ray diffraction (XRD), and ultraviolet-visible (UV-vis) spectroscopy. Rhodamine 6G (R6G) was selected as a model chemical to study the enhancement performance of substrate constructed by PS/SiO₂/Ag nanocomposite. Results indicated that the PS/SiO₂/Ag nanocomposite prepared based on the core-shell templates showed higher SERS activity. The beneficial effect was associated with a lower specific area of core-shell structure and the larger average diameter of nanosilvers than that of the raspberry-like templates.     

Extraction and chemical investigation of jute (Corchorus olitorius,Linn.) seed protein

Studies were made on the protein solubility of deoiled jute (Corchorus olitorius, Linn.) seed in aqueous solution over various pHs and in different concentrations of NaCl at pH 8.0. Chemical analysis of the seed protein showed 16 amino acids, of which 9 were essential. Gel filtration on Sephadex G-200 revealed the presence of four components, and their molecular weights were determined by two standard methods. Extractable jute seed proteins in salt solution were separated into six fractions electrophoretically (SDS-PAGE). The molecular weights of the six fractions were found to be 118,000; 103,000; 96,000; 67,500; 48,500; and 15,000.     

Preparation and evaluation of PANI/PTT electromagnetic shielding fabric by in-situ chemical polymerization

To prepare the flexible and stretchable electromagnetic shielding (EMS) fabric with environmental stability, this paper uses polytrimethylene terephthalate (PTT) fabric as substrate, the aniline monomer as raw material, hydrochloric acid (HCl) as the doping agent, ammonium persulfate (APS) as the oxidant to produce polyaniline (PANI)/PTT electromagnetic shielding fabric by in-situ chemical polymerization. It studies the influence of APS and HCl concentration on the surface electrical resistance and the absorption loss of electromagnetic shielding fabric. It can be observed that an increasing APS and HCl facilitate the absorption and spread of PANI into PTT fabric to form a conductive network, and improve the absorption loss efficiency, while the excess APS and HCl will hinder the PANI polymerization. The high electrical conductivity and absorption loss of the PANI/PTT fabric are obtained at the concentration of An 0.4 M, APS 0.4 M, HCl 1.25 M, and polymerization reaction time 120 min. Meanwhile, in-situ polymerization of PANI does not introduce new impurities and destroy the molecular structure of PTT.     

Solute-solvent interactions in acid-base dissociation: nine protonated nitrogen bases in water-DMSO solvents

A titration method utilizing glass electrodes and silver-silver chloride electrodes in a cell without liquid junction has been used to determine the acidic dissociation constants at 15, 25, and 35°C of nine protonated nitrogen bases in mixtures of water and dimethyl sulfoxide (DMSO). The mole fraction of DMSO in the mixed solvents was 0.2, 0.4, 0.6, and 0.8. The cell was calibrated with HCl (molality=0.01 mole-kg^?1) in the mixed solvents, and the ionic strength and chloride molality remained substantially unchanged during the titration with added base. This method minimizes the errors resulting from the formation of AgCl ₂ ^? in the media rich in DMSO. The pK _a of all the protonated bases passes through a minimum at a solvent composition close to that at which H₂O-DMSO mixtures display a maximum solvent structure. The results are discussed in terms of the preferential solvation of ions by the two types of solvent molecules. They are consistent with the hypothesis that increased solvent structure is accompanied by increased desolvation of the cation acids.     

Relating surface-enhanced Raman scattering signals of cells to gold nanoparticle aggregation as determined by LA-ICP-MS micromapping

The cellular response to nanoparticle exposure is essential in various contexts, especially in nanotoxicity and nanomedicine. Here, 14-nm gold nanoparticles in 3T3 fibroblast cells are investigated in a series of pulse-chase experiments with a 30-min incubation pulse and chase times ranging from 15 min to 48 h. The gold nanoparticles and their aggregates are quantified inside the cellular ultrastructure by laser ablation inductively coupled plasma mass spectrometry micromapping and evaluated regarding the surface-enhanced Raman scattering (SERS) signals. In this way, both information about their localization at the micrometre scale and their molecular nanoenvironment, respectively, is obtained and can be related. Thus, the nanoparticle pathway from endocytotic uptake, intracellular processing, to cell division can be followed. It is shown that the ability of the intracellular nanoparticles and their accumulations and aggregates to support high SERS signals is neither directly related to nanoparticle amount nor to high local nanoparticle densities. The SERS data indicate that aggregate geometry and interparticle distances in the cell must change in the course of endosomal maturation and play a critical role for a specific gold nanoparticle type in order to act as efficient SERS nanoprobe. This finding is supported by TEM images, showing only a minor portion of aggregates that present small interparticle spacing. The SERS spectra obtained after different chase times show a changing composition and/or structure of the biomolecule corona of the gold nanoparticles as a consequence of endosomal processing.     

A novel electrochemical DNA biosensor construction based on layered CuS–graphene composite and Au nanoparticles

A novel CuS–graphene (CuS-Gr) composite was synthesized to achieve excellent electrochemical properties for application as a DNA electrochemical biosensor. CuS-Gr composite was prepared by a hydrothermal method, in which two-dimensional graphene served as a two-dimensional conductive skeleton to support CuS nanoparticles. A sensitive electrochemical DNA biosensor was fabricated by immobilizing single-stranded DNA (ss-DNA) labeled at the 5′ end using 6-mercapto-1-hexane (HS-ssDNA) on the surface of Au nanoparticles (AuNPs) to form ssDNA-S–AuNPs/CuS-Gr, and hybridization sensing was done in phosphate buffer. Cyclic voltammetry and electrochemical impedance spectroscopy were performed for the characterization of the modified electrodes. Differential pulse voltammetry was applied to monitor the DNA hybridization using an [Fe(CN)₆]^3?/4? solution as a probe. Under optimum conditions, the biosensor developed exhibited a good linear relationship between the current and the logarithm of the target DNA concentration ranging from 0.001 to 1 nM, with a low detection limit of 0.1 pM (3σ/S). The biosensor exhibited high selectivity to differentiate one-base-mismatched DNA and three-base-mismatched DNA. The results indicated that the sensing platform based on CuS-Gr provides a stable and conductive interface for electrochemical detection of DNA hybridization, and could easily be extended to the detection of other nucleic acids. Graphical abstracts

?