Radiation synthesis and characterization of poly(N,N-dimethylaminoethyl methacrylate-co-N-vinyl 2-pyrrolidone) hydrogels

In this study, radiation synthesis and characterization of swelling behavior and network structure of poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA), and poly(N,N-dimethylaminoethyl methacrylate-co-N-vinyl 2-pyrrolidone) (P(DMAEMA-co-VP)), hydrogels were investigated. PDMAEMA and P(DMAEMA-co-VP) hydrogels in the rod forms were prepared by irradiating the ternary mixtures of DMAEMA/VP/cross-linking agent, ethyleneglycol dimethacrylate (EGDMA), by gamma rays at ambient temperature. In composition ranges where the three components were completely miscible, water was also added to the ternary mixture to provide the formation of homogeneous polymerization and gelation. The influence of irradiation dose, comonomer, VP, and cross-linking agent, EGDMA, content on the total percentage gelation and monomer conversion were investigated. The effect of pH and temperature on the swelling behavior of hydrogels have also been examined. Hydrogels showed typical pH response and temperature responses, such as low-pH and low temperature swelling and high-pH and high temperature deswelling. Polymer-solvent interaction parameter (χ) and enthalpy and entropy changes appearing in the χ parameter for the P(DMAEMA-co-VP)-water system were determined by using Flory-Rehner theory of swelling equilibrium. The negative values for ΔH and ΔS indicate that prepared pure PDMAEMA and P(DMAEMA-co-VP) hydrogels have lower critical solution temperature (LCST) and Flory-Rehner theory of swelling equilibrium provides a satisfactory agreement to the experimental swelling data of the hydrogels.     

The Influence of Temperature and Drug Concentrations Prednisolone in NIPAAm Copolymer

Controlled delivery systems would be more beneficial and ideal if the drug could be delivered with respond to external environmental change. It could be used to overcome the shortcomings of conventional dosage forms. Therefore, the correct amount of drug would be released upon the stimulation of such a temperature and concentration change. The purpose of study is to investigate the influence of temperature and drug concentration from poly(2-hydroxyethyl methacrylate and N-isopropylacrylamide)/poly(HEMA-NIPAAm). The macroporous structure 5HEMA15NIPAAm was showed the most rapid responsiveness in swelling ratio, polymer volume fraction, swelling and deswelling kinetics. The high drug loading capacity was achieved at or below ambient temperature, whilst the release profile was revealed sustain release of conventional anti-inflammatory drug; prednisolone 21 hemisuccinate sodium salt. In general, drug loading capacity and drug diffusion kinetics are influence by the porosity of hydrogels, temperature, and drug concentration.     

Tailoring thermoresponsive nanostructured poly(N-isopropylacrylamide) hydrogels made with poly(acrylamide) nanoparticles

The thermoresponsive behavior and mechanical properties of nanostructured hydrogels, which consist of poly(acrylamide) nanoparticles embedded in a cross-linked poly(N-isopropylacrylamide) hydrogel matrix, are reported here. Nanostructured hydrogels exhibit a tuned volume phase transition temperature (T _VPT), which varies with nanoparticle content in the range from 32 up to 39–40 °C. Moreover, larger equilibrium water uptake, faster swelling and de-swelling rates, and larger equilibrium swelling at 25 °C were obtained with nanostructured hydrogels compared with those of conventional ones. Elastic and Young’s moduli were larger than those of conventional hydrogels at similar swelling ratios. The tuned T _VPT and the de-swelling rate were predicted with a modified Flory–Rehner equation coupled with a mixing rule that considers the contribution of both polymers. These behaviors are explained by a combination of hydrophilic/hydrophobic interactions and by the controlled inhomogeneities (nanoparticles) introduced by the method of synthesis.     

Novel crosslinked thermoresponsive hydrogels with controlled poly(ethylene glycol)—poly(propylene glycol) multiblock copolymer structure

New thermoresponsive crosslinked hydrogels with controlled multiblock copolymer structure were prepared from equimolar amounts of α,ω-diamino poly(propylene glycol)s with molecular weights (MW) 230, 400, and 2,000 g mol^?1 and diepoxy-terminated poly(ethylene glycol)s of approximate MW 1,000; 2,000; and 4,000 g mol^?1. Their thermoresponsive character was investigated on the 10–70 °C interval, while the swelling behavior was tested at 21, 37, and 50 °C. All hydrogels displayed temperature sensitivity, but a volume phase transition was noticed only in the case of poly(propylene glycol) (PPG)₂₀₀₀-containing hydrogels. The volume phase transition temperature (T _VPT ) depended on the MW of the hydrophilic poly(ethylene glycol) (PEG) chains attached to the PPG₂₀₀₀ block, as well as on the added salts. Longer PEG blocks determined a shift of T _VPT towards higher values, while the influence of the salt added was in agreement with the Hofmeister series, except for NaH₂PO₄ which determined the destruction of the hydrogel network. The equilibrium swelling degree depended on the MW of both PEG and PPG blocks, as well as on temperature. The analysis of the swelling process indicated a modification of the gel characteristics with temperature and second-order kinetics for the water penetration into the hydrogel.     

Effects of intercalated hydrotalcite on drug release behavior for poly(acrylic acid-co-N-isopropyl acrylamide)/intercalated hydrotalcite hydrogels

The influence of positively charged intercalated hydrotalcite (IHT) in the anionic poly(acrylic acid-co-N-isopropyl acrylamide), poly(AA-co-NIPAAm)/hydrotalcite nanocomposite hydrogels on the drug release behavior for the drugs with different charges was investigated in this study. Results show that the loading amount and release ratio of indomethacin are affected by the swelling ratio in saline solution and related to the affinity in the alcohol solution, respectively. The loading amount and release ratio of caffeine are affected by the swelling ratio. The loading amount of crystal violet (CV) increased with an increase of the content of intercalating agent in IHT of the gel but the fractional release of CV in the gels decreases with increase in intercalating agent content. The result of release and loading for phenol red in the hydrogels is contrary to CV.     

“Smart” carboxymethylchitosan hydrogels crosslinked with poly(N-isopropylacrylamide) and poly(acrylic acid) for controlled drug release

Carboxymethylchitosan (CMC) hydrogels containing thermo-responsive poly(N-isopropylacrylamide) (poly(NIPAAm)) and pH-responsive poly(acrylic acid) (poly(AA)) were prepared via a free radical polymerization in the presence of hexamethylene-1,6-di-(aminocarboxysulfonate) crosslinking agents. A proper ratio of CMC to NIPAAm and AA used in the reaction was investigated such that the thermo- and pH-responsive properties of the hydrogels were obtained. Water swelling of the hydrogels was improved when the solution pH was in basic conditions (pH 10) or the temperature was below its lower critical solution temperature (LCST). Effects of the change in solution temperature and pH on water swelling properties of the hydrogel as well as the releasing rate of an entrapped drug were also investigated. The hydrogels were not toxic and showed antibacterial activity against Straphylococcus aureus (S. aureus). The pH- and thermo-responsive properties of this novel “smart” hydrogel might be efficiently used as dual triggering mechanisms in controlled drug release applications.     

Synthesis, characterization and thermoreversible behaviours of poly(dimethyl siloxane)/poly(N-isopropyl acrylamide) semi-interpenetrating networks

Simultaneous and sequential poly(N-isopropyl acrylamide) (PNIPAAm)/poly(dimethyl siloxane) (PDMS) semi-interpenetrating polymer networks (IPNs) with different linear PDMS contents were prepared by free radical polymerization method. Their phase morphologies have been characterized by FTIR, DSC and SEM. The simultaneous semi-IPNs exhibited phase transition temperatures (T_pt) shifted higher temperature from glass transition temperatures (T_g) of their respective homopolymers, suggesting a heterophase morphology and only physical entanglement between the PNIPAAm network and linear PDMS with high molecular weight (Mn≈9000 g/mol). For sequential semi-IPNs, the shift of T_pts towards lower temperature suggested that the chemical interaction between the constituents of the IPNs increased with increasing PDMS content in the network. In addition, these semi-IPNs were characterized for their thermo-sensitive behaviour by equilibrium swelling studies. The results showed that incorporation of hydrophobic PDMS polymer into the thermo- and pH-sensitive PNIPAAm and P(NIPAAm-co-IA) (itaconic acid) hydrogels by semi-IPN formation decreased swelling degrees of IPNs without affecting their LCSTs whereas addition of acrylated PDMS (Tegomer V-Si 2250) as crosslinker instead of N,N^′-methylenebisacrylamide (BIS) into the structures of these hydrogels changed their LCSTs along with their swelling degrees.     

Preparation and characterization of sodium carboxymethylcellulose/poly(N-isopropylacrylamide)/clay semi-IPN nanocomposite hydrogels

A new kind of pH-/temperature-responsive semi-interpenetrating polymer network hydrogels based on linear sodium carboxymethylcellulose (CMC) and poly(N-isopropylacrylamide) (PNIPA) cross-linked by inorganic clay (CMC/PNIPA/Clay hydrogel) was prepared. The temperature- and pH-responsive behaviors, the mechanical properties of these hydrogels were investigated. The CMC/PNIPA/Clay hydrogels exhibited a volume phase transition temperature around 32 °C with no significant deviation from the conventional PNIPA hydrogels. The swelling ratio of the CMC/PNIPA/Clay hydrogels gradually decreased with increasing the contents of clay. The influence of pH value on swelling behaviors showed that there is a maximum swelling ratio at pH 5.9. Moreover, the CMC/PNIPA/Clay hydrogels exhibited excellent mechanical properties with high tensile stress and elongation at break in excess of 1200%.     

Dual temperature‐ and pH‐sensitive hydrogels from interpenetrating networks and copolymerization of N‐isopropylacrylamide and sodium acrylate

Hydrogels responsive to both temperature and pH have been synthesized in the forms of sequential interpenetrating networks (IPNs) of N‐isopropylacrylamide (NIPAAm) and sodium acrylate (SA) and compared with the crosslinked random copolymers of N‐isopropylacrylamide and SA. Whereas the stimuli‐sensitive behaviors of copolymer hydrogels were strongly dependent on the ionic SA contents, the IPN hydrogels exhibited independent swelling and thermal behaviors of each network component. The sequences and media in the synthesis of IPNs influenced the swelling capacities of the IPNs, but not the temperature or pH ranges at which the swelling changes occurred. In IPNs, a more expanded primary gel network during the synthesis of the secondary network contributed to the better swelling of the final IPNs. Both the swelling and thermal behaviors of the IPNs suggest that poly(N‐isopropylacrylamide) and poly(sodium acrylate) are phase separated regardless of their synthesis conditions. The presence of the poly(sodium acrylate) network did not influence the temperature or the extent of phase transition of the poly(N‐isopropylacrylamide) network in the IPNs, but did improve the thermal stability of the IPNs. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3293–3301, 2004     

Diffusion of poly(ethylene glycol) and ectoine in NIPAAm hydrogels with confocal Raman spectroscopy

The diffusion behavior of poly(ethylene glycol) (PEG) in N-isopropylacrylamide (NIPAAm) hydrogels was investigated using confocal Raman spectroscopy with regard to temperature (25°C, 30°C and 35°C), PEG concentration (10 and 40?wt.%), PEG molecular weight (2,000 and 12,000?g/mol) and addition of the compatible solute ectoine (0.1 and 2?wt.%). Swelling and shrinking of the gels was observed by means of confocal Raman spectroscopy. The swelling behavior of NIPAAm gels in aqueous solutions of PEG and ectoine was found to resemble the swelling behavior in pure water with regard to temperature, i.e., the gel shrinks with increasing temperature. However, the presence and concentration of PEG and ectoine influence the swelling behavior by lowering the volume phase-transition temperature of the gel and facilitating shrinking. In some cases, a re-swelling of the gel was observed after the initial shrinking at the onset of PEG diffusion, which can be explained by PEG changing the chemical potential in the gel phase as it diffuses into the sample allowing the water to re-enter. The expulsion of water from the gel during shrinking and the so-caused increase of PNIPAAm and PEG concentrations in some cases led to the PEG diffusion seemingly being faster in more shrunken gels despite of their higher diffusion resistance.     

Characterization of stimuli-sensitive polymers for biomedical applications

Stimuli-sensitive polymers were synthesized by copolymerizing varying ratios of N-isopropyl acrylamide(NIPAAm) and acrylic acid(AAc). The influence of polyelectrolytes on the lower critical solution temperatures(LCSTs) of these temperature/pH sensitive polymers was investigated in the pH range of 2-12. Polyelectrolyte complexes were prepared by mixing poly(NIPAAm-co-AAc) as anionic polyelectrolyte with poly(allyl amine)(PAA) or poly(L-lysine)(PLL) as cationic polyelectrolytes, respectively. Back titration was performed to determine the pK_a values of PAAc in poly(NIPAAm-co-AAc) and to study the effect of comonomer ionization on the cloud point temperature. The effect of polyelectrolyte complex formation on the conformation of PLL was studied as a function of temperature by means of circular dichroism(CD). The swelling ratio of poly(NIPAAm-co-AAc) hydrogels as a function of pH at various temperature was obtained by measuring the weight of the hydrogels in buffer solutions. The LCSTs of the poly(NIPAAm-co-AAc) were strongly affected by pH, polyelectrolyte solutes, AAc content, and charge density. The influence of more hydrophobic PLL as a polyelectrolyte on the cloud point of PNIPAAm/water in the copolymer was stronger than that of poly(allyl amine)(PAA). Indomethacin was loaded into these hydrogels, and controlled release of this molecule from the hydrogel was determined under various temperature and pH conditions using UV/Vis spectrophotometry.     

Preparation of hydrogel from green polymer

A new method was used for the production of hydrogels from green polymer with a higher swelling ratio. These hydrogels were synthesized first by graft copolymerization between acrylamide (AM) and poly(vinyl alcohol) (PVA) with alkaline or kraft lignin (AM‐PVA‐g‐lignin) and then by mixing with acrylamide monomer. The kraft and alkaline lignins were isolated from pulping liquor and characterized using UV and FT‐IR spectroscopy, and the formed hydrogels were characterized using FT‐IR spectroscopy and scanning electron microscopy (SEM). Compared with kraft lignin hydrogel, the alkaline lignin hydrogel had very high swelling ratios and slower water uptake and deswelling rates attributed to its compatible network structure. The hydrogels formed were used also to study the influence of sodium chloride on the absorption capacity at room temperature and swelling ratios at different temperatures. Copyright © 2004 John Wiley & Sons, Ltd.     

Dynamic deswelling studies of poly(N-vinyl-2-pyrrolidone/itaconic acid) hydrogels swollen in water and terbinafine hydrochloride solutions

Deswelling kinetics of water and terbinafine hydrochloride adsorbed poly(N-vinyl-2-pyrrolidone/itaconic acid) P(VP/IA) hydrogels were investigated. Hydrogels were prepared by irradiating the ternary mixture of VP/IA and cross-linking agent ethylene glycol dimethacrylate (EGDMA) in water by γ-rays at ambient temperature. Hydrogels swelled in pure water and terbinafine hydrochloride (TER-HCl) solutions at room temperature and deswelling or water loss were investigated between 4 and 45 °C temperature range and on human skin. The influence of IA content, % swelling, temperature and TER-HCl content on the water loss from gel matrix were investigated. Induction time for 80% water loss from hydrogel systems are found to increase from 9.6 to 21.2 h by increasing IA content in the gel system at 25 °C and decreased by 11 h with addition of TER-HCl in the gel system. Kinetic analyses had shown that the basic properties affecting the water loss behavior of these hydrogels are the IA and TER-HCl content and temperature of the medium.     

Polyampholyte-tuned lyotrop lamellar liquid crystalline systems

The influence of a polyampholyte, i.e., poly(N,N′-diallyl-N,N′-dimethyl-altmaleamic carboxylate) (PalH), on the lamellar liquid crystalline (LC) system sodium dodecyl sulfate (SDS)/decanol/water was investigated by means of microdifferential scanning calorimetry, small-angle X-ray diffraction (SAXS), and cryo-scanning electron microscopy. After incorporating PalH into the lamellar liquid crystalline system, SAXS measurements show that three different LC phases exist: i.e., a swelling, slightly swelling, and non-swelling one. At pH 4, the positively charged polymer with an extended conformation can directly adsorb at the anionic head groups of the surfactant and more compact vesicles are formed at room temperature. At pH 9, the electrostatic interactions between the polyampholyte (in a more coiled conformation) and the sulfate head groups of the SDS are leveled off and incompact vesicles are formed at room temperature. That means in presence of the polyampholyte the morphology of the LC phase, i.e., the supramolecular vesicle structure, can be tuned by varying the pH and/or the temperature.

Photocrosslinking of Polyglycidol and Its Derivative: Route to Thermoresponsive Hydrogels

Hydrogels of biologically well‐tolerated, high‐molar‐mass polyglycidol (PGl) and its thermoresponsive derivative poly(glycidol‐co‐ethyl glycidyl carbamate) have been obtained by direct UV crosslinking in the solid state. Polymers with molar masses up to 1.45 × 10⁶ g mol⁻¹ were crosslinked in the presence of benzophenone or (4‐benzoylbenzyl)trimethylammonium chloride as photosensitizers. The photosensitizer concentration was varied from 2 to 10 wt%. The influence of polymer composition and photosensitizer type and amount on the crosslinking efficiency, swelling and temperature behavior of the obtained hydrogels was investigated. The photocrosslinking of PGl and poly(glycidol‐co‐ethyl glycidyl carbamate) led to hydrogels with swelling degrees up to 1700%. The swelling degrees of the hydrogels decreased with the increase of the environmental temperature indicating the thermoresponsive nature of gels. The swelling of obtained gels can be controlled by varying the composition of the copolymer precursor and by the network density.     

Gradual phase transition of poly(N-isopropylacrylamide-co-acrylic acid) gel induced by electric current

The copolymer gels showing gradual phase transition induced by temperature were synthesized by redox random copolymerization of N-isopropylacrylamide (NIPAAm) and acrylic acid (AAc) monomer under a constant electric current. The behavior of gradual phase transition induced by temperature was examined by measuring the thermal properties, pKa values and swelling ratio. The experimental results indicate that temperature-induced gradual phase transitions of poly(NIPAAm-co-AAc) gel are mainly driven by transport before polymerization and protonation/ionization of the AAc, caused by the electric current.     

Characterisation of N-vinyl-2-pyrrolidone-based hydrogels prepared by a Diels-Alder click reaction in water

N-vinyl-2-pyrrolidone-based hydrogels were prepared by the Diels-Alder reaction in water for the first time. Copolymers of N-vinyl-2-pyrrolidone(VP) and furfuryl methacrylate(FM) were synthesised by free radical polymerisation in toluene at 70 °C by using 2,2′-azobisisobutyronltrile as an initiator. Polymeric dienophile (PEG-AMI) was prepared from N-alaninyl maleimide (AMI) and poly(ethylene glycol) (PEG) by using N,N′-dicyclohexylcarbodiimide (DCC) as a dehydrating agent. The prepared dienes and dienophile were then dissolved in water and mixed, leading to gelation via Diels-Alder reaction after some time. The gelation times of different copolymers and PEG-AMI in different solvents and at different temperatures were measured by the vial inversion method, and the swelling behaviour of dried hydrogels was studied using a general gravimetric method. The gelation time was shorter in water than in organic solvents, and the gelation time decreased with the increase of temperature and FM content in copolymers. Conversely, the swelling ratios increased with the decrease of temperature and FM content in the copolymers. Disassembly experiments suggested that N,N-dimethylformamide (DMF) could accelerate the retro-DA reaction.     

Fast responsive poly(N-isopropylacrylamide) hydrogels prepared in phenol aqueous solutions

Fast responsive poly(N-isopropylacrylamide) (PNIPAAm) hydrogels with improved properties were prepared in phenol aqueous solutions with different concentrations. Due to the expanded network structure in water, the resulted hydrogels are capable of absorbing a large amount of water, i.e. exhibits a much increased swelling ratio at room temperature. Importantly, the hydrogels demonstrated much faster response rate than that of traditional PNIPAAm hydrogel upon external temperature increase.     

Swelling of ferrogels of poly(acrylic acid) with ferric oxide nanoparticles stabilized by chitosan

The processes of swelling of poly(acrylic acid) ferrogels prepared via radical polymerization in an aqueous suspension of ferric oxide nanoparticles with the weighted average size of 23.5 nm obtained by laser evaporation method and stabilized by chitosan (М = 5.3 × 10⁵ and degree of deacetylation of 62%) are studied. The swelling of washed ferrogels depends on the content of chitosan and decreases abruptly at a polymer concentration exceeding 1 g/L. At a chitosan concentration above 1 g/L, the chemical network of poly(acrylic acid) is formed on the fluctuation network of chitosan in solution. As pH increases, these ferrogels are contracted owing to formation of an interpolymer complex of chitosan with poly(acrylic acid) subchains.