Contact angle and adsorption behavior of carboxylic acids on α-Al2O3 surfaces

There is good correlation of contact angle measurements and contact angles calculated from surfactant adsorption density data for an electrically neutral surface, as reported in a previous paper for the system hematite-aqueous solution-ketone, with surfactant hexadecyl sulfonic acid. The same method is not sufficient when the hematite surface is electrically charged. Data was collected to develop the appropriate form of an electrostatic term for the analysis. Acid-base titration was used to evaluate surface electrical properties versus pH for the hematite used in the study. Surfactant adsorption isotherms were measured at pH of 4.5, 5.5, 6, and 7 to use in developing an equation for effect of surface potential on contact angle. After adding a term for the contribution of the electric field, the contact angles calculated from adsorption data follow the measured contact angles well.     

More Convenient and Suitable Methods for Sphere Tensiometry

Two new convenient and suitable gravimetric methods of measuring surface and interfacial tensions of liquids and contact angles of liquids on a spherical surface by pulling a sphere through the interface were examined. First, the accuracy of numerical integration was increased. Second, two methods which treat the experimental data were presented and compared. Both methods can be used for determination of the contact angle and interfacial tension at the same time.     

On some relations between advancing, receding and Young's contact angles

Problems of experimental determination and theoretical verification of equilibrium contact angles are discussed basing on the literature data. A relationship between the advancing and receding contact angles versus the equilibrium contact angle is described and then verified using the literature contact angles determined on paraffin wax and polypropylene. Using the proposed relationship and experimentally determined equilibrium contact angles, obtained by plotting the advancing and receding contact angles versus the contact angle hysteresis or by applying vibration of the system liquid drop/solid surface, it is found that the same value of the surface free energy for paraffin wax is calculated from the contact angles of water and ethylene glycol. However, in the case of polypropylene some inconsistency appears between the equilibrium contact angles of the probe liquid used and the calculated surface free energy. More experimental data of the equilibrium contact angle are needed to verify further the relationship.     

巯基乙胺自组装膜表面润湿性的变化

报道了巯基乙胺自组装膜在不同的时间尺度内表面润湿性的特征变化.利用接触角滴定方法对其表面状态进行实时监控表明,自组装膜由固/液界面转移至固/气界面后,接触角在短时间内经历了一个快速升高过程和一个相对较慢的变化过程.从表面自由能的角度,讨论了该现象的机理.采用不同pH值的缓冲溶液进行接触角滴定,得到了巯基乙胺自组装膜的滴定曲线,从而确定表面pKb值为1.7±0.2.从接触角滴定曲线在长时间内的变化趋势中发现,pK_b值无显著变化,但曲线整体向上平移,并且滴定曲线中上下平台的差值随时间增长而减小.     

Factors influencing the contact angle value. The contact angle,as a characteristic of the properties of solid surfaces

A survey of publications concerning the properties of solids in relation to wetting phenomena is presented. Factors influencing the contact angle value as well as problems of objective approach to research into wetting phenomena are discussed. Peculiarities of the direct and reverse processes during the formation of the solid—liquid—vapor three-phase contact and the inevitability of contact angle hysteresis for polar solids and liquids are analyzed. It is suggested that contact angle hysteresis is due to high energy of the interaction between the liquid and the solid and hence a long relaxation time of the three-phase contact system. Specific features of the response of a solid surface to all surface processes (“chemomechanics”) is discussed. Cleaning of solid surfaces as well as surface preparation for repeated measurements is considered. It is shown that good reproducibility of results is possible if conditions for sample preparation are met. The results of determination of the activation energy for wetting of glass surface with water are presented. The influence of the structure of solids (their hardness) on the contact angle values is demonstrated. Inevitability of the presence of different-type active sites characterized by different dissociation constants (pK_a) on the surface of solids is discussed. The pK_a values and content of these surface sites obtained from potentiometric titration and wetting data are estimated. The estimates thus obtained are in reasonable agreement with each other and can thus be used in practical applications. However, potentiometric titration is currently inappropriate for evaluating the content of individual surface sites as well as the surface charge.     

Influence of the work of adhesion on the dynamic wetting of chemically heterogeneous surfaces

The velocity dependence of the dynamic contact angle for a glycerol-water mixture wetting two different chemically heterogeneous surfaces (mixed thiols on gold and partially methylated titania, 16 samples in all) was studied. The molecular kinetic theory (MKT) of wetting was used to interpret the dynamic contact angle data. The equilibrium displacement frequency ( K 0) was predominantly determined by the viscous contribution from the bulk liquid, with a minor contribution from the surface. The mean distance between surface sites (lambda) decreased with increasing work of adhesion. The contact line friction coefficient zeta 0 was found to vary exponentially with the work of adhesion, enabling the unit flow volume of the liquid to be obtained.     

Contact angle interpretation in terms of solid surface tension

Recent experimental (low-rate) dynamic contact angles for 14 solid surfaces are interpreted in terms of their solid surface tensions. Universality of these experimental contact angle patterns is illustrated; other reasons that can cause data to deviate from the patterns are discussed. It is found that surface tension component approaches do not reflect physical reality. Assuming solid surface tension is constant for one and the same solid surface, experimental contact angle patterns are employed to deduce a functional relationship to be used in conjunction with the Young equation to determine solid surface tensions. The explicit form of such a relation is obtained by modifying Berthelot’s rule together with experimental data; essentially constant solid surface tension values are obtained, independent of liquid surface tension and molecular structure. A new combining rule is also derived based on an expression similar to one used in molecular theory; such a combining rule should allow a better understanding of the molecular interactions between unlike solid–liquid pairs.     

Solvatochromism as an alternative for contact angle measurements in the characterisation of modified polymer surfaces

Polyolefine surfaces have been pre-treated by UV/ozone and UV/water methods. The increase in polar groups on a polymer surface and the contribution of these polar groups to the adhesion of the polymer has been investigated by using contact angles and tensile strength tests. Because contact angle measurements do not give information about the specific polar groups on the surface we have used solvatochromic analyses to identify specific polar groups. The results showed that solvatochromic analyses is a promising method to discriminate between different kinds of polar groups and therefore solvatochromic surface characterisation may become an important surface analytical tool in adhesive technology.     

Ceforanide: a new and efficient corrosion inhibitor for mild steel in HCl solution

The corrosion inhibition properties of ceforanide for mild steel in HCl solution were analyzed by electrochemical impedance spectroscopy, potentiodynamic polarization, and gravimetric methods. The increase in inhibitor concentration and immersion time showed a positive effect on inhibition efficiency. The experimental data showed a frequency distribution and therefore a modeling element with frequency dispersion behavior and a constant phase element have been used. In aqueous acid solution, mild steel reacts by evolution of hydrogen. Visual observations showed that the hydrogen evolution decreased (i.e., corrosion inhibition effect increased) with increasing concentration of ceforanide. Potentiodynamic polarization study revealed that ceforanide acted as a mixed type of inhibitor. The results obtained from different methods are in good agreement. The adsorption behavior of ceforanide is experimentally investigated by contact angle measurement on metal surface. The contact angle of metal surface to the acid solution increased with inhibitor concentration; thereby confirming the increased hydrophobic nature of metal surface to the acid solution having inhibitors.     

Contact-Angle Titrations of Cysteamine Selfassembled Monolayers on Gold--A Sensitive Tool for Monitoring the Surface Modification Process

The self-assembled monolayers (SAMs). which were prepared by spontaneous adsorption of cysteamine on gold surface, were characterized using contact-angle titrations. Contact-angle titration data acquired for the cysteamine SAMs exhibited a smooth transition in contact angle between plateau regions at low and high pH value. The surface pK_b, was estimated to be 1.8±0.2, much lower than that in solution. The electroactive azobenzene group was anchored to the monolayer via amide surface reaction. Thus the formed SAMs were further subjected to exchange in dilute pentanethiol soluition. At each stage of modification, the surface was monitored by con-tact-angle titration and cyclic voltanimetry. It was found that the titration curves obviously shifted to the higher contact-angle direction with the increase of surface hydrophobicity. The results are in good agreement with the cyclic voltammetric measurements, demonstrating that the contact-angle titration is a useful technique for monitoring the step by step surface reactions.     

Dynamic contact angles under evaporation

Wetting kinetics in the presence of heat transfer, evaporation, and Marangoni effect has been explored using a method used by Joanny and de Gennes [C. R. Acad. Sci. Ser. II 299, 279 (1984)]. The method solves for the dynamic contact angle alpha by equating the rate of surface work to the rate of dissipation. The result in the form of dynamic contact angle alpha as a function of capillary number Ca agrees well with existing experimental data. Qualitative comparisons have been made in cases where quantitative data do not exist. Finally, a form of contact line instability is predicted, for which some experimental justifications are seen.     

Contact angle hysteresis of bovine serum albumin (BSA) solution/metal (Au-Cr) coated glass substrate

Bovine serum albumin (BSA) has an extraordinary property to carry biomolecules. An experimental study on the wettability of BSA is presented in this study. The variations in the surface tension and the equilibrium contact angle with the change in BSA concentration are also reported. The surface tension and the contact angle are measured with pendant and sessile drop techniques, respectively. A nonlinear decrement in the surface tension with the increment in the BSA concentration is observed. An equilibrium contact angle of a BSA solution with particular concentration is determined by studying the hysteresis in the contact angle from dynamic contact angle measurements. The needle-in-drop technique is used to study the hysteresis of the contact angle. It is observed that the obtained surface tension and the equilibrium contact angle vary with the BSA concentration. In this reported study, for the considered combination of the BSA concentration and solid surface, the liquid drop does not recede as the drop volume decreases, which represents nonreceding contact angle condition. The increment in the contact angle with the increment in the BSA concentration is observed. Finally, it is observed that the inclusion of the proteins not only changes the surface tension but also changes the contact angle.     

Contact angle interpretation: re-evaluation of existing contact angle data

We have recently shown that static contact angles measured by conventional goniometer techniques could be meaningless in the context of the Young equation. There is an abundance of contact angles in the literature that are of unknown status. Here, we explored whether one should completely neglect the literature contact angle data. Existing static contact angles for 34 different types of solid surfaces from Zisman and co-workers were evaluated in terms of their solid surface tensions using experimental contact angle patterns. A fortran computer program was implemented to automate these procedures. It was found that literature contact angles do not have to be discarded completely; they can be used to determine solid surface tensions, with caution. The surface tensions for the 34 solid surfaces from Zisman et al. are also reported.     

化学力显微镜对自组装单分子膜的力滴定研究

The concept of force titration was firstly proposed based on the technique of Chemical Force Microscopy (CFM). Self-Assembled Monolayer (SAM) on substrate surface can be titrated with buffer solutions at a nanometer scale by measuring the adhesion force between the SAM-modified substrate and probe tip. The plot of adhesion force vs pH value was termed as force titration curve. As an example, the titration behavior of w-mercaptoundecanoic acid monolayer on gold has been studied. It was found that there is a big hump around pH 5~6 in its force titration curve. Taking the contact angle titration result together, an interaction model for the monolayer was suggested from the chemical hysteresis point of view.     

Prediction of solid-fluid interfacial tension and contact angle

Two simple equations have been developed using the lattice theory and the regular solution assumption to predict the solid-vapor and solid-liquid interfacial tension. The required parameters are the liquid critical temperature and volume, the solid melting temperature and the molar volume of liquid and solid compounds. To confirm the models, the predicted solid-fluid interfacial tension values have been used to predict the contact angle of the liquid drop on the solid surface applying Young's equation. Agreement of the predicted contact angle with the experimental data reveals the reliability of the developed models.     

On the lifetime of evaporating sessile droplets

The evaporation of sessile droplets with a constant base radius (pinning mode) and a constant contact angle (depinning mode) has been experimentally observed. Here we analyzed the effect of substrate hydrophobicity on the lifetimes of evaporating droplets for the two modes. Theoretical predictions were obtained and compared with available experimental results. The theoretical analysis and experimental results show that linear methods of extrapolating limited experimental data for a transient droplet contact angle and base radius overpredict the droplet lifetime. Likewise, the linear extrapolation of limited experimental data for transient droplet volume underpredicts the droplet lifetime. Correct methods of extrapolating limited experimental data for transient droplet parameters are described, discussed, and validated. The new methods removed inconsistencies in the previous theory and experimental analysis. Master equations and master curves for the droplet lifetime for the two evaporation modes are obtained and experimentally confirmed.     

Equilibrium contact angles of liquid droplets on ideal rough solids

This work proposes a theoretical model for predicting the apparent equilibrium contact angle of a liquid on an ideal rough surface that is homogeneous and has a negligible body force, line tension, or contact angle hysteresis between solid and liquid. The model is derived from the conservation equations and the free-energy minimization theory for the changes of state of liquid droplets. The work of adhesion is expressed as the contact angles in the wetting process of the liquid droplets. Equilibrium contact angles of liquid droplets for rough surfaces are expressed as functions of the area ratios for the solid, liquid, and surrounding gas and the roughness ratio and wetting ratio of the liquid on the solid for the partially and fully wet states. It is found that the ideal critical angle for accentuating the contact angles by the surface roughness is 48°. The present model is compared with existing experimental data and the classical Wenzel and Cassie-Baxter models and agrees with most of the experimental data for various surfaces and liquids better than does the Wenzel model and accounts for trends that the Wenzel model cannot explain.     

Theoretical evaluation of nano- or microparticulate contact angle at fluid/fluid interfaces: analysis of the excluded area behavior upon compression

A novel method for the determination of the particle contact angle at the liquid/gas or liquid/liquid interface based on the excluded area concept revealed, in spite of its simplicity, some serious difficulties connected with the exact quantitative particle deposition at the interface and with changes in the particulate contact angle upon binary monolayer compression. The comprehensive theoretical consideration of the contact angle behavior made for such a system allowed considerable improvements: firstly, the prediction of direction of the particles' displacement at surface pressure increase is now possible and hence an unambiguous identification of particle hydrophobicity can be done. Secondly, the analytical relation describing the dependence of the particulate contact angle on the surface tension (surface pressure) was derived, allowing the prediction of whether or not particles of a given hydrophobicity will be expelled from the monolayer at certain surface pressure and of the area relinquished by the displaced particles. Thirdly, the transformation of this relation upon taking into consideration the initial conditions led to a linear dependence between excluded area and normalized surface tension allowing the determination of the particle contact angle and the exact number of deposited particles simultaneously and independently of each other. Finally, the application of the improved approach to the previously collected experimental data yielded reasonable values for both particle contact angle and number of deposited particles.     

Nanodrop of an Ising magnetic fluid on a solid surface

The density functional theory of inhomogeneous simple fluids is extended to an Ising magnetic fluid in contact with a solid surface, which is subjected to an external uniform or nonuniform magnetic field. The system is described by two coupled integral equations regarding the magnetic moment and fluid density distributions. The dependence of the contact angle that a nanodrop makes with the solid surface on the parameters involved in the magnetic interactions between the molecules of fluid and between the molecules of fluid and an external magnetic field is calculated. For the uniform magnetic field, the contact angle increases with increasing magnetic field, approaching an asymptotic value that depends on the strength of the fluid-fluid magnetic interactions. In the nonuniform field generated by a permanent magnet, the contact angle first increases with increasing magnetic field B(M) and then decreases, with the decrease being almost linear for large values of B(M). The obtained results are in qualitative agreement with the experimental data on the contact angle of magnetic drops on a solid surface available in the literature.