噻吩光电化学聚合的研究

噻吩在水溶液中先经低聚反应,生成的低聚合物再在阳极氧化成膜,光照可促进低聚合物的形成,使噻吩在Pt、Au基低上选择性地进行光电聚合。即在低于噻吩电聚合电位下,形成明显光照点的聚噻吩膜。     

LOW POTENTIAL ELECTROPOLYMERIZATION OF ANISOTROPIC CONDUCTIVE POLYTHIOPHENE FILMS AND FABRICATION OF ELECTRICAL DEVICES

The complexation of thiophene with a Lewis acid with moderate acidity as a solvent, such as BF_3-ethyl ether (BFEE) remarkedly lowered the electrochemical polymerization potential. The positively chargedmetal surface of electrode in the process of electrochemical deposition enhanced the coordination interactionbetween π-electrons of thiophene unit and the metal, which makes thiophene rings lie parallel to the surfaceof electrode, resulting in a highly ordered polymeric structure. Because of the large intra-chain transferintegrals, the transport of charge is believed to be principally along the conjugated chains, which is muchgreater than the inter-chain hopping. The specific electrical resistance across the polythiophene film thicknessis more than 10~4 times than that along the surface plane of the film. In this paper we review the recentdevelopment of polymerization technique by low potential electrochemical method performed in our lab andseveral electrical devices in which the compact polythiophene films, such as anionic and cationic sieves, andlaminate film junction of undoped polythiophene derivatives were used.     

噻吩在M(111)(M=Pd,Pt, Au)表面的吸附

采用密度泛函理论(DFT), 选取DMol³程序模块, 对噻吩在M(111) (M=Pd, Pt, Au)表面上的吸附行为进行了探讨. 通过对噻吩在不同底物金属上的吸附能、吸附构型、Mulliken 电荷布居、差分电荷密度以及态密度的分析发现, 噻吩在Pd(111)面上的吸附能最大, Pt(111)面次之, Au(111)面最小. 吸附后, 噻吩在Au(111)面上的构型几乎保持不变, 最终通过S端倾斜吸附于top 位; 噻吩在Pd(111)及Pt(111)面上发生了折叠与变形, 环中氢原子向上翘起, 最终通过环平面平行吸附于hollow 位. 此外, 噻吩环吸附后芳香性遭到了破坏, 环中碳原子发生sp³杂化, 同时电子逐渐由噻吩向M(111)面发生转移, M(111)面上的部分电子也反馈给了噻吩环中的空轨道, 这种协同作用最终导致了噻吩分子稳定吸附于M(111)面.     

噻吩在M(111)(M=Pd,Pt,Au)表面的吸附(英文)

采用密度泛函理论(DFT),选取DMol3程序模块,对噻吩在M(111)(M=Pd,Pt,Au)表面上的吸附行为进行了探讨.通过对噻吩在不同底物金属上的吸附能、吸附构型、Mulliken电荷布居、差分电荷密度以及态密度的分析发现,噻吩在Pd(111)面上的吸附能最大,Pt(111)面次之,Au(111)面最小.吸附后,噻吩在Au(111)面上的构型几乎保持不变,最终通过S端倾斜吸附于top位;噻吩在Pd(111)及Pt(111)面上发生了折叠与变形,环中氢原子向上翘起,最终通过环平面平行吸附于hollow位.此外,噻吩环吸附后芳香性遭到了破坏,环中碳原子发生sp3杂化,同时电子逐渐由噻吩向M(111)面发生转移,M(111)面上的部分电子也反馈给了噻吩环中的空轨道,这种协同作用最终导致了噻吩分子稳定吸附于M(111)面.     

Improved Energy Conversion Efficiency of ZnO/Polythiophene Solar Cell in Ga-Doped ZnO Nanorod Array Photoanode

We reported the fabrication and doping effect of Ga-doped ZnO nanorods/electropolymerized polythio-phene(e-PT) hybrid photovoltaic(h-PV) devices. Ga-Doped ZnO nanorod array photoanode devices were fabricated via hydrothermally growing nanorods on sol-gel spin-coating ZnO seed layer, and then the nanorod array was immersed into a thiophene solution to yield a thin polythiophene film by electrochemically polymerization. Afterwards, a thin layer of Al was deposited on the surface of polythiophene to make an electrode for photovoltaic measurement. The ZnO nanorods with different Ga-doping contents were characterized by means of X-ray diffraction(XRD), scanning electron micrograph(SEM) and X-ray photoelectron spectroscopy(XPS). Photovoltaic J-V characterization was performed on the e-PT/ZnO bilayer and bulk heterojunction(BHJ) devices. Though the unsubstituted polythiophene is not an ideal polymer material for solar cells with high power conversion efficiency, it is a sound model for the study on the effect of dopant in hybrid materials. The results indicate that doping Ga can substantially improve the power conversion efficiency of the ZnO-polythiophene solar cell.     

Ammonia adsorption on and diffusion into thin ice films grown on Pt(111)

Ammonia adsorption on and diffusion into thin ice films grown on a Pt(111) surface were studied using Fourier transform infrared spectroscopy (FTIR) and thermal desorption spectroscopy. After exposing the crystalline ice film to ammonia molecules at 45 K (ammonia/ice film), we have detected an intriguing feature at 1470 cm(-1) in the FTIR spectra, which is derived from the adsorption of ammonia on the ice with a characteristic structure which appears in thin film range. The peak intensity of this feature decreases gradually as the thickness of the substrate ice increases. In addition, we have detected a feature at 1260 cm(-1) which appears after annealing the ammonia/ice film. The feature corresponds to the ammonia molecules which reach the ice/Pt(111) interface through the ice film. Intriguingly, the intensity of this feature decreases with the ice thickness and there is a linear relation of the peak intensity of the features at 1470 and 1260 cm(-1). We propose a model in which the solubility of the ammonia molecules is much higher for the thin ice film than that for the ideal ice.     

Highly ordered polymer films of amphiphilic, regioregular polythiophene derivatives

The fabrication and characterization of highly ordered thin films made from amphiphilic, regioregular polythiophene derivatives are described. Films of poly(3-(11-(2-tetrahydropyranyloxy)undecyl)thiophene (PTHPUDT) were prepared by the Langmuir-Blodgett technique. The amphiphilic nature of the polymer affords layer-by-layer deposition and the formation of multilayer films of head-to-head and tail-to-tail Y-type structure. X-ray diffraction studies indicate bilayer separations of approximately 30 A. Anisotropic optical absorption in the plane of the film indicates that the thiophene backbones are preferentially oriented along the dipping direction. Further, polarized light microscopy studies indicate that these films are highly birefringent and that the optical retardation is uniform over the entire film. Ellipsometry studies confirm the sizable magnitude of the birefringence. Optical second-harmonic generation studies of multilayer films provide information regarding both the thiophene orientation within the film and the anisotropic distribution of chromophores in the surface plane. Taken together, these data offer strong evidence of highly ordered films in which the hydrophobic polythiophene chains lie parallel to the substrate surface with their alkyl chains oriented normal to the surface, as dictated by the hydrophilic nature of the alkyl chain's terminal tetrahydropyran functional group. As such, these films offer the potential for elucidating the connection between polymer morphology and physical property in materials that are otherwise subject to a sufficiently complex distribution of morphologies that such a correspondence is precluded.     

碱性介质中甘氨酸在Pt电极上解离吸附和氧化反应的原位红外反射光谱研究

运用原位红外反射光谱研究了碱性介质中甘氨酸在Pt电极上的解离吸附和氧化反应行为,并利用纳米Pt膜电极的异常红外效应鉴定反应过程中生成的表面吸附物种.结果表明:甘氨酸在Pt电极上极易发生解离,生成强吸附于电极表面上的氰基负离子,该吸附物种在低于0V电位下能稳定存在,并抑制甘氨酸的进一步反应.当电位高于0.2V时,氰基负离子被氧化为氰酸根离子进入溶液,使甘氨酸发生氧化反应,生成氰酸盐和碳酸盐等产物.     

环己烯对噻吩在CuY分子筛上吸附的影响机制

A CuY zeolite prepared by liquid phase ion exchange was characterized by X-ray photoelectron spectroscopy, pyridine in situ Fourier transform infrared (in situ FTIR) spectroscopy, and ammonia temperature programmed desorption. The effect of cyclohexene on the adsorption of thiophene over the prepared CuY zeolite was explored by in situ FTIR. In particular, the role of the zeolite's Br?nsted acidity was investigated in the adsorption process. The results show that the percentage of Cu⁺ on the surface of the CuY zeolite can reach 77%. The surface acidity of the CuY zeolite mainly comprises medium and strong Br?nsted acidity and Lewis acidity. According to the adsorption results, cyclohexene negatively influences thiophene adsorption on the Br?nsted or Lewis acid sites in CuY by competitive adsorption. Although polymerization of thiophene and cyclohexene can occur easily on the HY or REY zeolites, the presence of Br?nsted acids in the CuY zeolite was not sufficient to polymerize either thiophene or cyclohexene. This difference may be caused by an anti-synergistic effect between the Cu ions of the CuY zeolite and neighboring Br?nsted acid sites, the result of which inhibits the polymerization of adsorbed thiophene and cyclohexene.     

聚噻吩制备条件对其结构和导电性能的影响

通过改变聚噻吩合成条件(温度、浓度、反应时间)得到各种不同样品, 用FESEM, FTIR光谱, Raman光谱, XRD, UV-Vis光谱和TG等手段对样品进行研究. 结果表明, 不同的制备条件会影响噻吩环的连接方式, 直接影响聚噻吩结构的分布. 导电性能研究表明, 聚噻吩的结构差异和其导电性能直接相关, 实验证明以α-α相连接的聚噻吩有更高的电导率.     

Pt/γ-Al2O3催化剂活性位的表征及其噻吩加氢脱硫催化活性

A series of Pt/γ Al 2O 3 catalysts with different content of Pt were characterized by using low temperature FT IR spectroscopy of adsorbed CO, while their catalytic activity for HDS was investigated with thiophene as a model substrate. On the basis of the experimental results, it has been obtained that the pseudo zero order rate of the thiophene HDS reaction is well linearly proportional to the total area of the two IR bands at 2?080 and 1?850 cm -1 of CO adsorbed on Pt/γ Al 2O 3, and that the Pt sites for CO adsorption may be the active centers for thiophene HDS reaction.     

原位傅里叶变换红外光谱研究Y型分子筛表面酸性对吸附有机分子的影响

采用吡啶原位吸附傅里叶变换红外(Py-FTIR)光谱对液相离子交换(LPIE)和固相离子交换(SSIE)法制备的CeY分子筛以及HY和NaY的酸性进行了测定. 在原位条件下采用单探针分子噻吩、环己烯和苯对其在分子筛上的吸附过程进行了研究; 以噻吩和环己烯、噻吩和苯组成的双探针分子对吸附过程中存在的竞争吸附、催化反应以及吸附机理进行了系统研究. 结果表明, HY和L-CeY 分子筛表面强Brönsted (B)酸性位可导致吸附在其表面的噻吩发生低聚反应以及吸附的环己烯产生二聚环己烯碳正离子. 低聚的噻吩和吸附的环己烯在分子筛上发生强的化学吸附, 进一步抑制和阻碍噻吩硫化物与分子筛吸附活性中心发生作用, 从而降低了吸附剂的选择性以及吸附硫化物的能力. 吸附剂表面Lewis (L)酸中心是吸附的主要活性中心, 大量弱的L 酸, 有利于噻吩吸附. 并且, S-CeY分子筛表面弱的L酸对吸附噻吩具有一定的选择性, 它受到环己烯的影响较小, NaY吸附剂对噻吩、环己烯和苯选择性较差, 它只与吸附质作用的先后有关.     

Growth of novel polythiophene and polyphenyl films via surface polymerization by ion-assisted deposition

Surface polymerization by ion-assisted deposition (SPIAD) is used here to grow novel polythiophene and polyphenyl thin films on a silicon surface by hyperthermal, mass-selected thiophene cations coincident with a thermal beam of alpha-terthiophene or p-terphenyl neutrals. X-ray photoelectron spectroscopy (XPS) observes a large enhancement in film growth for SPIAD compared with either thiophene ions or alpha-terthiophene exposure alone. Changes in S/Si and C/Si ratios from XPS, direct observation of higher polymerization products by mass spectrometry, characteristic vibrations in the Raman data, and enhanced stability in a vacuum all indicate that 200 eV SPIAD polythiophene films are most efficiently polymerized at a 1/150 ion/neutral ratio. Other ion/neutral ratios are less efficient at film growth, in the order 1/150 > 1/450 > 1/900 > direct ion deposition > 1/50. Changes in C/Si ratios and higher polymerization products indicate polymerization occurs in SPIAD polyphenyl films grown with a 1/100 ion/neutral ratio. Furthermore, thiophene ions are found to incorporate into some, but not all, of the polymerization products observed in mass spectrometry.     

铂纳米粒子电极上NO吸附和还原的CV及原位FTIR研究

运用电化学循环伏安法(CV)和原位傅里叶变换红外反射光谱(in situ FTIRS)研究了酸性介质中铂纳米粒子电极(nm-Pt/GC)上NO吸附及其电催化还原过程.结果表明,NO分子的吸附是电催化还原的重要步骤.在铂纳米粒子电极上饱和吸附的NO存在两种不同键合强度的吸附态,其中弱吸附的NO(NOW)在0.60 V至-0.05 V电位区间还原生成N2O和NH4+;而强吸附的NO(NOS)则在-0.05 V至-0.15 V区间还原,其产物为NH+.     

丙三醇在Pt电极上吸附和氧化过程的原位FTIR反射光谱研究

运用电化学循环伏安(CV)和原位FTIR反射光谱方法, 研究了丙三醇在Pt电极上的氧化过程。结果指出, 丙三醇的氧化是一个复杂的表面过程。其间包括脱水、吸附、解离等步骤。根据CV和红外实验数据, 本文提出了Pt电极上丙三醇解离吸附的表面反应机理和不同电位下丙三醇氧化的分子过程。     

纳米结构Pt膜方波电位法制备及特殊红外性能

运用方波电位法处理Pt微电极,制备一系列具有较高表面粗糙度的纳米结构薄膜.扫描隧道显微镜（STM）观察到薄膜由Pt金属岛组成,并测得所研制的薄膜虽然其平均厚度从58 nm 增加到139 nm,但Pt金属岛的平均尺度仅从102 nm增加到114 nm,而岛的平均高度也只在15～18 nm之间变化.以CO为探针分子,结合原位FTIR反射光谱研究,发现所制备的纳米结构薄膜上吸附态CO的红外吸收都给出类Fano光谱,初步归结为Pt金属岛的尺度效应.     

CO吸附原位红外光谱结合分子模拟计算研究FCC汽油加氢脱硫催化剂的选择性

以脱硫选择性不同的2组催化裂化汽油加氢脱硫催化剂为研究对象, 采用CO吸附原位红外光谱表征了2组催化剂的活性相特征, 并通过分子模拟计算方法比较了助剂Co加入前后噻吩和1-己烯在催化剂表面的电荷分布、吸附能及其加氢反应的活化能等, 探讨了助剂Co的加入对选择性加氢脱硫催化剂脱硫选择性的作用机理. 结果表明, 加氢脱硫催化剂CoMoS活性相的增加有利于提高催化剂的加氢脱硫/加氢降烯烃(HDS/HYD)选择性. 与1-己烯加氢位相比, Co的加入显著提高了噻吩分子加氢位的缺电子性, 噻吩在催化剂表面的吸附度增强, 显著降低噻吩加氢反应的能垒, 从而使噻吩加氢反应更易进行. 这也表明CoMoS为高HDS活性、高HDS/HYD选择性的活性相.     

Preparation and properties of a novel polythiophene,poly[(3‐hexyliminomethyl)thiophene] with a high regioregularity

Poly[(3‐hexyliminomethyl)thiophene]s (P3HITs) were synthesized from the polymerizations of 2,5‐dibromo‐(hexyliminomethyl)thiophene and 5‐bromo‐2‐iodo‐3‐(hexyliminomethyl)thiophene by Grignard metathesis method. The corresponding P3HITs with low regioregularity (70%) and high regioregularity (95%) were obtained, respectively. UV–vis and photoluminescence spectra of P3HIT were dependent on the regioregularity and solvent polarity. By hydrolysis of the imino groups in the side chains under acidic conditions, P3HIT was successfully converted into the polythiophene (P3TCHO) having aldehyde groups. This transformation was also performed facilely by exposing the P3HIT film to HCl gas to give the polythiophene having aldehyde moiety. The reverse way from aldehyde to imine was also successfully demonstrated by treating the film with triethylamine vapor. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Electrochromic properties of polythiophene polyrotaxane film

The electrochromic properties of a polythiophene polyrotaxane film consisting of a polythiophene backbone wrapped by the tetra-cationic cyclophane, cyclobis(paraquat-p-phenylene), were characterized. A naked reference polythiophene film, i.e., polythiophene without tetra-cationic cyclophane, was also characterized. The surface morphology and thickness of the film (L) were observed by atomic force microscopy. The surface of the naked reference polythiophene film has micrometer-scale polythiophene aggregates, which causes the darker color of the film and smaller color contrast in the electrochromic process. The polythiophene polyrotaxane gives a more homogeneous and brighter colored film owing to the suppression of molecular interactions between the polythiophene chains by the tetra-cationic cyclophanes. Potential-step chronoamperometric measurement provided the area density of the oxidizable sites (Γ) and the apparent diffusion coefficient of the charge transport in the film. From linear relationship between L and Γ, the concentrations of the oxidizable sites in the polythiophene polyrotaxane and naked reference polythiophene films were calculated to be 1.3 and 2.4 mmol cm(-3), respectively. Interestingly, the polythiophene polyrotaxane film afforded a significantly larger apparent diffusion coefficient than the naked reference polythiophene film. This result suggests that the rate-determining step of the charge transport is not the electron hopping between the polythiophene chains but the transport of charge-compensating counterions from the solvent into the polythiophene. We believe that the counteranions of the tetra-cationic cyclophane provide a pathway allowing the charge-compensating counteranions to migrate from the solvent to polythiophene. The polythiophene polyrotaxane film showed faster color change than the naked reference polythiophene film in the electrochromic reaction. These results indicate that our polythiophene polyrotaxane is a better electrochromic material than the naked reference polythiophene.     

Low potential electropolymerization of thiophene at a copper oxide electrode

Conductive polythiophene (PT) film was electrochemically deposited onto a copper electrode covered with an oxide film from distilled BF₃–diethyl ether (BFEE) solution containing 15 mM thiophene, and the oxidation potential of thiophene was relatively low (1.0 V versus Ag|AgCl). The obtained film was homogenous and flexible, and could be easily cut into any shape as desired.