Highly selective iodide electrode based on the copper(II)-N,N'-bis(salicylidene)-1,2-bis(p-aminophenoxy)ethane tetradentate complex.

In this paper, a new PVC-based liquid-membrane anion-selective electrode based on a copper(II) of N,N'-bis(salicylidene)-1,2-bis(p-aminophenoxy)ethane tetradentate complex (Cu(II)BBAP) is described, which displays a preferential potentiometric response to iodide ion at pH 2.0 and an anti-Hofmeister selectivity sequence: I->SCN->ClO4->NO2->H2PO4->NO3->SO4(2-)>Br->Cl-. The electrode exhibits a near-Nernstian potential linear range of 8.2x10(-7)-1.0x10(-1) M with a detection limit of 5.3x10(-7) M and a slope of -58.8 mV per decade. The A.C. impedance technique and the UV/Vis spectroscopy technique were used to analyze the response mechanism. The electrode could be applied to determine iodide in medicine analysis, and the obtained results were fairly satisfactory.     

Investigation of the effects of Au-colloid modification on cobalt hexacyanoferrate film growth and mass transport by electrochemical quartz crystal microbalance

The growth of cobalt hexacyanoferrate (CoHCF) films on bare and Au-colloid-modified electrodes in nitrate or sulfate solutions was monitored by electrochemical quartz crystal microbalance. The average efficiency of CoHCF film growth for Au colloid modified electrodes is 23 and 12 ng cm(-2) s(-1) in KNO3 and K2SO4 solutions, respectively, while those values for the bare gold electrode are 15 and 9 ng cm(-2) s(-1), respectively. In K2SO4 solution, the apparent molar masses for the Au-colloid-modified electrode at lower and higher potential is 58.4 and 37.3 g mol(-1), respectively, which is larger than those for the bare gold electrode (51.7 and 26.3 g mol(-1), respectively). The respective results were also obtained in KNO3 solution. Furthermore, the difference of the apparent molar masses at lower and higher potential for Au-colloid-modified electrodes is smaller than that for bare gold electrodes in the same electrolyte. Additionally, the mechanism of charge propagation is dependent on different anions in electrolyte solutions at higher potentials where the second redox reaction of CoHCF occurs. Therefore, the existence of Au colloids can accelerate CoHCF film growth and weaken the effect of anions on mass transport.     

In situ characterisation of the aqueous gold colloid interface using CO as a surface probe: IR spectroscopic studies

Fourier transform infrared (FTIR) spectra are presented of CO gas-treated protected gold colloids prepared from hydrazinium hydrate reduction of an Au(III) precursor which reproducibly feature a weak, shortlived peak at ca. 2169 cm(-1). When the gold colloid was treated with 99% isotopically enriched (13)CO gas, the IR peak shifted to a frequency of 2114 cm(-1) which indicated that it represented a simple gold monocarbonyl species. The value of 2169 cm(-1) for the CO stretching frequency suggests the peak represents CO physisorbed on oxidised gold atoms on the colloid surface. The peak is not observed when the concentration of the colloidally dispersed gold is reduced either by use of lower starting salt concentrations or by aggregation. It is also not observed when solutions of the protecting agent or reducing agent or the dispersion medium (water) or even the starting Au(III) salts are CO-treated individually. This confirms that the spectral feature is uniquely associated with colloidally dispersed gold. In general, the work has shown that the surfaces of Au colloids in situ have partially oxidised Au character which is of interest in systems where supported nanoparticulate gold derived from colloid preparations are considered for low temperature oxidation catalysts for CO.     

Strong inclusion of inorganic anions into β-cyclodextrin immobilized to gold electrode

The inclusion of inorganic anions such as SO(4)(2-), NO(3)(-), and HPO(4)(2-) into the cavity of β-cyclodextrin monolayers on Au was examined by X-ray photoelectron spectroscopy (XPS), a quartz crystal microbalance (QCM), and chronocoulometric measurements of the competitive inclusion with ferrocene. The inclusion amounts of ferrocence in 0.2 M Na(2)SO(4), NaNO(3), and Na(2)HPO(4) solutions were less than 6% of the adsorption amount of β-cyclodextrin on Au, resulting in the apparent inhibition of the ferrocene redox reaction. The surface association constants of these anions reached about 10 on a logarithmic scale and were much higher than those for the inclusion of common organic guest compounds. A stronger anion inclusion was also demonstrated by the QCM response corresponding to the replacement of a preincluded organic guest with sulfate upon the injection of the sulfate solution. Quantitative analysis of the XPS data suggested a 1:1 association for each of these anions per surface β-cyclodextrin. There was no detectable inclusion for ClO(4)(-), Cl(-), and Br(-).     

Bis-dimethylaminobenzaldehyde Schiff-base cobalt(II) complex as a neutral carrier for a highly selective iodide electrode.

A new solvent polymeric membrane electrode based on N,N'-bis-(dimethylaminobenzaldehyde)-glycine cobalt(II) [Co(II)-BDMABG] as a neutral carrier is described, which displays a preferential potentiometric response to iodide ion and an anti-Hofmeister selectivity sequence in the following order: I- > ClO4- > Sal- > SCN- > NO2- > Br- > NO3- > Cl- > SO3(2-) > SO4(2-). The electrode exhibits a near-Nernstian potential linear range of 9.0 x 10(-7)-1.0 x 10(-1) M with a detection limit of 6.8 x 10(-7) M and a slope of -53.0 mV/decade in pH 2.0 of a phosphate buffer solution at 20 degrees C. The response mechanism is discussed in view of the A.C. impedance technique and the UV spectroscopy technique. The electrode was successfully applied to the determination of iodide in Jialing River and Spring in Jinyun Mountains with satisfactory results.     

Suppressed electrostatic ion chromatography with tetraborate as eluent and its application to the determination of inorganic anions in snow and rainwater

Tetraborate is investigated as the eluent ion for suppressed electrostatic ion chromatography (EIC) using a zwitterionic stationary phase. Good separation of a range of inorganic anions (SO4(2-), Cl-, NO3-, Br-, NO3-, ClO3-, and I-) was obtained, with detection limits for highly conducting ions (SO4(2-), Cl-, NO2-, Br- , and NO3-) being less than 8 x 10(-8) M, and for weakly conducting anions (ClO3- and I-) being 2.7 x 10(-7) and 5.8 x 10(-7) M, respectively. Calibration curves were linear up to 1.8 mM of each analyte. Retention times were found to increase with increasing eluent concentration and a linear relationship was observed between log k' and log[Na2B4O7] for all analytes. This behaviour is attributed to the progressive formation of a binary electrical double layer at the surface of the zwitterionic stationary phase. Retention times of analytes could be manipulated by varying the concentration of the eluent. This new suppressed-EIC system was applied to the determination of inorganic anions (SO4(-2) , CI-, NO3-, NO2-, and Br-) in snow and rainwater samples.     

Hexacyanoferrate as the Electrochemical Probe for 2-Mercaptobenzothiazole Modified Gold Electrode

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｒａｔｅｏｆｅｌｅｃｔｒｏｎｔｒａｎｓｆｅｒｉｓｍｕｃｈａｆｅｃｔｅｄｂｙｓｅｖｅｒａｌｆａｃｔｏｒｓ，ｓｕｃｈａｓｅｌｅｃｔｒｏｄｅｍａｔｅｒｉａｌ，ｅｌｅｃｔｒｏｄｅｆａｂｒｉｃａｔｉｏｎｔｅｃｈｎｉｑｕｅｓ，ｐｏｌ...     

阴离子对RhCl（CO）（TPPTS）2催化1—己烯氢甲酰化反应的影响

在烯烃氢甲酰化反应两相催化体系中,为提高催化剂活性及选择性,有采用外加无机盐的报道［１～３］．从这些文献可以看出,某些无机盐在反应中起到催化助剂的作用．我们曾经研究了硫酸钠及其它金属硫酸盐中的阳离子对反应的影响［４,５］．在引入这些阳离子的同时,还有...     

Oxidation of highly unstable <4 nm diameter gold nanoparticles 850 mV negative of the bulk oxidation potential

Here we describe the oxidation of <4 nm diameter Au nanoparticles (NPs) attached to indium tin oxide-coated glass electrodes in Br(-) and Cl(-) solution. Borohydride reduction of AuCl(4)(-) in the presence of hexanethiol or trisodium citrate (15 min) led to Au NPs <4 nm in diameter. After electrochemical and ozone removal of the hexanthiolate ligands from the thiol-coated Au NPs, Au oxidation peaks appeared in the range 0-400 mV vs Ag/AgCl (1 M KCl), which is 850-450 mV negative of the bulk Au oxidation peak near 850 mV. The oxidation potential of citrate-coated Au NPs is in the 300-500 mV range and those of 4 and 12 nm diameter Au NPs in the 660-780 mV range. The large negative shift in potential agrees with theory for NPs in the 1-2 nm diameter range. The oxidation potential of Au in Cl(-) solution is positive of that in Br(-) solution, but the difference decreases dramatically as the NP size decreases, showing less dependence on the halide for smaller NPs.     

Ion-selective electrodes for anionic surfactants using a cyclam derivative as ionophore

The cyclam derivative 1,4,8,11-tetra(n-octyl)-1,4,8,11-tetraazacyclotetradecane (L) has been used as carrier for the preparation of PVC-based membrane ion-selective electrodes for anionic surfactants. Different membranes were prepared using L as ionophore, tetra-n-octylammonium bromide (TOAB) as cationic additive and dibutyl phthalate (DBP) or o-nitrophenyl octyl ether (NPOE) as plasticizers. The final used electrode contained a membrane of the following composition: 56% DBP, 3.4% ionophore, 3.8% TOAB and 36.8% PVC. This electrode displays a Nernstian slope of -60.0+/-0.9 mV/decade in a 2.0 x 10(-3) to 7.9 x 10(-6) mol dm(-3) concentration range and a limit of detection of 4.0 x 10(-6) mol dm(-3). The electrode can be used for 144 days without showing significant changes in the value of slope or working range. The electrode shows a selective response to dodecyl sulfate (DS-) and a poor response to common inorganic cations and anions. The selective sequence found was DS->ClO4->HCO3->SCN->NO3- approximately CH3COO- approximately I->Cl->Br->IO3- approximately NO2- approximately SO3(2-)>HPO4(2-)>C2O4(2-)>SO4(2-), i.e. basically following the Hoffmeister series except for the hydrophilic anion bicarbonate. Most of the potentiometric coefficients determined are relatively low indicating that common anions would not interfere in the DS- determination. A complete study of the response of the electrode to a family of surfactant was also carried out. The electrode showed a clear anionic response to DS- and to Na-LAS and a much poorer response to other anionic surfactants and to non-ionic surfactants. Also the electrode shows certain non-linear cationic response in the presence of cationic and zwitterionic surfactants. The electrode was used for the determination of anionic surfactants in several mixtures, and the results obtained were compared to those found using a commercially available sensor.     

ZrO2负载碳纳米管吸附去除水中氟的研究

以ZrO2负载多壁碳纳米管(ZrO2-MWCT)为吸附剂,系统研究了其对水中F-的吸附、脱附性能。结果表明,F-在ZrO2-MWCT吸附剂上的吸附等温线可以用Freundlich方程模拟,吸附动力学符合拟二级动力学方程,吸附速率随着F-初始浓度的提高而减低。当pH为4~5时,F-在ZrO2-MWCT吸附剂上的吸附量最大。水中阴离子的存在降低ZrO2-MWCT对F-的吸附量,不同阴离子对F-影响的大小顺序为:CO32->SO42->Cl->NO3-。吸附饱和的ZrO2-MWCT可用0.1mol/L的NaOH脱附再生,经4次再生后,其吸附量仍为14.55mg/g。     

Phosphate adsorption on synthetic goethite and akaganeite

Low crystalline iron hydroxides such as goethite (alpha-FeOOH) and akaganeite (beta-FeOOH) were synthesized, and the selective adsorption of phosphate ions from phosphate-enriched seawater was examined. The results of the distribution coefficients (K(d)) of oxoanions in mixed anion solutions at pH 8 follow the selectivity order Cl-, NO3-, SO4(2-) < CO3(2-), HPO4(2-) for goethite, and Cl-, CO3(2-) < NO3- < SO4(2) < HPO4(2-) for akaganeite. In seawater, both adsorbents show high selectivity for phosphate ions despite the presence of large amounts of major cations and anions in seawater. The adsorption isotherms fitted better with the Freundlich equation and the maximum uptake of phosphate from phosphate-enriched seawater was 10 mg P/g at an equilibrium phosphate concentration of 0.3 mg P/L on both adsorbents. The phosphate adsorption/desorption cycles show that akaganeite is an excellent adsorbent even after 10 cycles and its chemical stability is good.     

Structure and electrochemistry of 4,4'-dithiodipyridine self-assembled monolayers in comparison with 4-mercaptopyridine self-assembled monolayers on Au(111)

4,4'-Dithiodipyridine (PySSPy) monolayers on Au(111) were investigated by cyclic voltammetry, X-ray photoelectron spectroscopy (XPS) and in situ scanning tunneling microscopy (STM). The studies were performed in solutions of different anions and pHs (0.1 M H2SO4, 0.1 M HClO4, 0.1 and 0.01 M Na2SO4, 0.1 and 0.01 M NaOH). The cyclic current-potential curves in H2SO4 show current peaks at about 0.4 V, which are absent for all other electrolytes at this potential. The XPS data suggest that PySSPy adsorbs via the S endgroup on the gold surface and the S-S bond breaks during adsorption. From the chemical shift of the N(ls) peak, it is concluded that in acidic media the self-assembled monolayer (SAM) is fully protonated, whereas in basic solution it is not. The pKa is estimated to be 5.3. STM studies reveal the existence of highly ordered superstructures for the SAM. In Na2SO4 and H2SO4, a (7 x mean square root of 3) structure is proposed. However, whereas in Na2SO4 solutions the superstructure does not change with potential, in 0.1 M H2SO4 the superstructure is observed only negative of the current peak at +0.4 V. At more positive potentials, the film becomes disordered. The results are compared to those for 4-mercaptopyridine (PyS) SAMs. XPS experiments and current-potential curves indicate that both molecules adsorb in the same manner on Au(111), that is, even in the case of PySSPy the adspecies is PyS. The STM results, however, call for a more subtle interpretation. While in Na2SO4 solutions the observed superstructures are the same for both SAMs, markedly different structures are found for PySSPy and PyS SAMs in 0.1 M H2SO4.     

One-pot preparation of mono-dispersed and physiologically stabilized gold colloid

We have developed a rapid and simple method for the preparation of nearly mono-dispersed gold colloids with a fairly high concentration above 10 mM using hydroxylamine as the reducing agents, in the presence of α-methoxy-ω-mercaptoethyl-poly(ethylene glycol)(MeO-PEG-SH). It was found that a hydroxylamine acted not only as a reducing agent, but also as a nucleation agent under alkaline reaction conditions. Though the colloid concentration was fairly high, the dispersion stability was remarkably improved even in a high ionic strength in the range greater than 1 M NaCl, in which conventional citrate gold colloids immediately flocculate and precipitate. The obtained colloid was successfully re-dispersed in aqueous media after lyophilization. In addition, the prepared gold colloid reduced a protein adsorption significantly on its surface. Concerning these results, the obtained colloidal dispersion may be suitable for biological applications, since a regionally concentrated colloidal dispersion with dispersion stability is required for bio-labeling and bio-imaging systems.Electronic Supplementary Material Supplementary material is available for this article at     

Electrical Control of Alkanethiols Self-Assembly on a Gold Surface as an Approach for Preparation of Microelectrode Arrays

 It is shown by capacitive monitoring that the self-assembly of alkanethiols on gold electrodes and desorption of these self-assembled monolayers from the electrodes are controlled by the electrode potential. At neutral pH, chemical adsorption of alkanethiols was observed at an electrode potential of +300 mV vs SCE, but only physical adsorption was detected when the electrode potential was −1400 mV vs SCE. At electrode potentials between these values (−300 mV, −600 mV), chemical adsorption of alkanethiols occurred, but the alkanethiol monolayers were not stable in the absence of the alkanethiol in the bulk solution and were desorbed from the gold electrode. The desorption rate was higher at more negative electrode potentials. These results can be used in designing methods for electrically addressable immobilization of different receptors on (micro)electrode arrays. This has been demonstrated by deposition of two different types of alkanethiols onto a two-electrode array. Received June 24, 1998. Revision October 19, 1998.     

Anion-induced adsorption of ferrocenated nanoparticles

Au nanoparticles fully coated with omega-ferrocenyl hexanethiolate ligands, with average composition Au225(omega-ferrocenyl hexanethiolate)43, exhibit a unique combination of adsorption properties on Pt electrodes. The adsorbed layer is so robust that electrodes bearing submonolayer, monolayer, and multilayer quantities of these nanoparticles can be transferred to fresh electrolyte solutions and there exhibit stable ferrocene voltammetry over long periods of time. The kinetics of forming the robustly adsorbed layer are slow; monolayer and submonolayer deposition can be described by a rate law that is first order in nanoparticle concentration and in available electrode surface. The adsorption mechanism is proposed to involve entropically enhanced (multiple) ion-pair bridges between oxidized (ferrocenium) sites and certain specifically adsorbed electrolyte anions on the electrode. Adsorption is promoted by scanning to positive potentials (through the ferrocene wave) and by high concentrations of Bu4N+ X- electrolyte (X- = ClO4(-), PF6(-)) in the CH2Cl2 solvent; there is no adsorption if X- = p-toluenesulfonate or if the electrode is coated with an alkanethiolate monolayer. The electrode double layer capacity is not appreciably diminished by the adsorbed ferrocenated nanoparticles, which are gradually desorbed by scanning to potentials more negative than the electrode's potential of zero charge. At very slow scan rates, voltammetric current peaks are symmetrical and nearly reversible, but exhibit E(fwhm) considerably narrower (typically 35 mV) than ideally expected (90.6 mV, at 298 K) for a one-electron transfer or for reactions of multiple, independent redox centers with identical formal potentials. The peak narrowing is qualitatively explicable by a surface-activity effect invoking large, attractive lateral interactions between nanoparticles and, or alternatively, by a model in which ferrocene sites react serially at formal potentials that become successively altered as ion-pair bridges are formed. At faster scan rates, both deltaE(peak) and E(fwhm) increase in a manner consistent with a combination of uncompensated ohmic resistance of the electrolyte solution and of the adsorbed film, as distinct from behavior produced by slow electron transfer.     

The effects of the specific adsorption of anion on the reactivity of the Ru(0001) surface towards CO adsorption and oxidation: in situ FTIRS studies

The dynamics of adsorption and oxidation of CO on Ru(0001) electrode in sulfuric acid solution have been studied using in situ FTIR spectroscopy under potential control and at open circuit, the latter at 20 and 55 degrees C. The in situ IR data show clearly that the bisulfate anion adsorbs on the Ru(0001) surface over the potential range from -200 mV to 350 mV (vs. Ag/AgCl) at 20 degrees C in the absence and presence of adsorbed CO; however, increasing the temperature to 55 degrees C and/or increasing the concentration of dissolved O(2) reduces the bisulfate adsorption. The formation of surface (hydro-) oxide at higher potentials replaces the bisulfate adsorbates. Both linear (CO(L)) and three-fold hollow bonded CO (CO(H)) adsorbates were produced following CO adsorption at Ru(0001) in H(2)SO(4), as was observed in our previous studies in HClO(4). However, the amount of adsorbed CO observed in H(2)SO(4) was ca. 10% less than that in HClO(4); in addition, the CO(L) and CO(H) frequencies were higher in H(2)SO(4), and the onset potential for CO(ads) oxidation 25 mV lower. These new results are interpreted in terms of a model in which the adsorbed bisulfate weakens the CO adlayer, allowing the active Ru oxide layer to form at lower potentials. Significantly different results were observed at open circuit in H(2)SO(4) compared both to the data under potential control and to our earlier data in HClO(4), and these observations were rationalized in terms of the adsorbed HSO(4)(-) anions (pre-adsorbed at -200 mV) inhibiting the oxidation of the surface at open circuit (after stepping from the initial potential of -200 mV), as the latter was no longer driven by the imposed electrochemical potential but via chemical oxidation by trace dissolved O(2). Results from experiments at open circuit at 55 degrees C and using oxygen-saturated H(2)SO(4) supported this model. The difference in Ru surface chemistry between imposed electrochemical control and chemical control has potential implications with respect to fuel cell electrocatalysis.     

纳米金双巯基修饰金电极差分脉冲伏安法测定多巴胺和抗坏血酸

在裸金电极上自组装4,4-二甲基联苯硫醇(MTP)膜(MTP/AuSAMs),再电还原氯金酸溶液修饰纳米金,得纳米金双巯基修饰金电极(NG/MTP/Au).研究了多巴胺(DA)和抗坏血酸(AA)在NG/MTP/Au上的电化学行为,发现该修饰电极对DA、AA的氧化具有良好的电催化作用,多巴胺(DA)和抗坏血酸(AA)的氧化峰电位差达到155mV,可以实现对此二组分混合溶液的选择性测定.差分脉冲法测得的峰电流与DA、AA浓度分别在5.0×10-7～1×10-4mol.L-1和3.5×10-6～1.0×10-3mol.L-1范围内呈线性关系,检测限(3σ)分别为1.5×10-7mol.L-1和1.2×10-6mol.L-1,相关系数0.998.     

Highly selective thiocyanate electrode based on bis-[N-(2-hydroxyethyl)salicylaldimino]copper(II) complex as a neutral carrier.

A novel selective thiocyanate electrode of a PVC membrane based on bis-[N-(2-hydroxyethyl)salicylaldimino]copper(II) [Cu(II)-BNSDM] as a neutral carrier is reported. The selectivity sequence of this electrode is as follows: SCN- > ClO4- > I- > Sal- > Br- > NO2- > Cl- > NO3- > H2PO4- > SO4(2-), which is an anti-Hofmeister selectivity sequence. The electrode exhibits a Nernstian potential linear range to thiocyanate from 1.0 x 10(-1) to 6.0 x 10(-6) mol/L with a detection limit of 2.0 x 10(-6) mol/L and a slope of (-59.0+/-0.2)mV/decade in pH 5.0 of a phosphate buffer solution at 25 degrees C. Electrochemical impedance spectroscopy (EIS) and UV spectroscopy techniques were performed to understand the response mechanism of the electrode. The electrode had the advantage of simplicity, high selectivity, fast response and low detection limit compared with the other electrode, which had been reported before. The electrode had been applied to wastewater analysis, and the obtained results were satisfactory.     

Heteropolynuclear complexes with the ligand Ph2PCH2SPh: theoretical evidence for metallophilic Au-M attractions

Addition of two equivalents of diphenylthiomethylphosphine (PPh2-CH2SPh) to the starting materials [Au(tht)2]A (tht = tetrahydrothiophene), AgCF3SO3, or [Cu(CH3CN)4]CF3SO3 produces the mononuclear derivatives [M(PPh2CH2SPh)2]A (M = Au, A = CF3SO3 (1a); M = Au, A = ClO4 (1b); M = Ag, A = CF3SO3 (4); M = Cu, A = CF3SO3 (5)) which are able to form the heterodinuclear complexes [AuM'(PPh2CH2SPh)2](CF3SO3)2 (M' = Ag (2), Cu (3)) with a P-Au-P environment. If the starting gold complex is [Au(C6F5)(tht)], reaction with the phosphine produces [Au(C6F5)-(PPh2CH2SPh)] (6) from which, by reaction with AgCF3SO3 or [Cu(CH3CN)4]CF3SO3, the "snake"-type linear complexes [Au2M(C6F5)2-(PPh2CH2SPh)2]CF3SO3 (M = Ag (7), Cu (8)) are obtained. If the silver starting complex is AgCF3CO2, reaction in a 1:1 ratio gives the tetranuclear complex [Au2Ag2(C6F5)2(PPh2CH2SPh)2-(CF3CO2)2] (9). When the molar ratio is 1:2 the trinuclear complex [AuAg2(C6F5) (CF3CO2)2(PPh2CH2SPh)] (10) is obtained. According to ab initio calculations, the presence of only one gold atom is enough to induce metallophilic attractions in the group congeners, and this effect can be modulated depending on the gold ligand.