Determination of acesulfame and sucralose in oral electrolyte maintenance solution by liquid chromatography

A method was developed for the direct, simultaneous determination of acesulfame and sucralose in oral electrolyte maintenance solution (OEMS). Analyte separation and quantitation were achieved by gradient reversed-phase liquid chromatography (LC) and UV absorbance at 192 nm, respectively. Detection at a second wavelength, 214 nm, was used to check sucralose peak purity; 20 microL OEMS was injected without preparation or dilution. System linearity was demonstrated as 192 nm peak area versus analyte concentration at 80-120% OEMS sweetener fortification (r > 0.999, and all residuals < 0.5%, for both acesulfame and sucralose). Spike recoveries for OEMS samples prepared at 3 spiking levels (80, 100, and 120% sweetener fortification) ranged from 100.3 to 102.0% for acesulfame, and from 97.9 to 102.3% for sucralose. In a second assessment of method accuracy, the same spiked OEMS samples were tested by 2 alternative methods: acesulfame (LC/UV at 230 nm) and sucralose (anion exchange-pulsed amperometric detection). Results for the alternative acesulfame method were within 1.2%, and for the alternative sucralose method within 6.0%, of the corresponding results obtained by the 192 nm method. Repeatability and intermediate precision RSD values were < 1 % for acesulfame and < 3% for sucralose. The limits of quantitation were 1.6 and 32 mg/L for acesulfame potassium and sucralose, respectively. Despite the weak UV absorptivity of sucralose and the consequent small size of its LC peak, no evidence was found for sucralose interference in any of the commercial OEMS flavors.     

Determination of isoflavones in ready-to-feed soy-based infant formula

An alkaline hydrolysis/liquid chromatography (LC) method was developed for determination of isoflavones in ready-to-feed soy-based infant formula. The method consists of a 15 min methanol extraction, 10 min alkaline hydrolysis, HCl neutralization, gravity filtration, aqueous dilution, and 50 min LC analysis with UV detection at 262 and 250 nm to quantify 6 isoflavone analytes: daidzin, glycitin, genistin, daidzein, glycitein, and genistein. The concentration averages for 10 commercial batches (microg aglycone/g formula) were daidzein, 6.12 +/- 1.23; glycitein, 1.19 +/- 0.16; genistein, 12.8 +/- 2.35; and total, 20.1 +/- 3.61. Validation experiments demonstrated extraction completion and analyte stability to alkaline hydrolysis. Spike recoveries ranged from 97.6 to 104.1%, and a series of accuracy assessments showed that isoflavone concentration determined by the method was within 5% of the true value. The relative standard deviation values for repeatability ranged from 0.4 to 2.2% (n = 10), and from 0.3 to 2.7% (n = 4) for intermediate precision. Isoflavone peak purity was verified by comparing sample and standard peak area ratios (262/250 nm). The limits of detection and quantitation (microg/ formula) ranged from 0.02 to 0.05 and 0.08 to 0.18 microg/g, respectively. The difference between our concentrations and those reported by others in 1995-1998 is attributable to the well-established seasonal variation in soybean isoflavone levels. Although the method was applied exclusively to ready-to-feed formula in the present study, it is equally suitable for powder and concentrated liquid infant formulas.     

Development and validation of column high-performance liquid chromatographic and ultraviolet spectrophotometric methods for citalopram in tablets

Column high-performance liquid chromatographic (LC) and UV spectrophotometric methods for the quantitative determination of citalopram, a potent and selective serotonin reuptake inhibitor, in tablets were developed. The parameters linearity, precision, accuracy, specificity, robustness, limit of detection, and limit of quantitation were studied according to International Conference on Harmonization guidelines. Chromatography was carried out by the reversed-phase technique on an ACE C18 column with a mobile phase composed of 0.30% triethylamine solution-acetonitrile (55 + 45, v/v) adjusted to pH 6.6 with 10% ortho-phosphoric acid at a flow rate of 1.0 mL/min and 25 degrees C. The UV spectrophotometric method was performed at 239 nm. The linearity of the LC method was in the range of 10.00-70.00 microg/mL, and 2.50-17.50 microg/mL for the UV spectrophotometric method. The interday and intraday assay precision was < 1.5% (relative standard deviation) for the LC and UV spectrophotometric methods. The recoveries were in the range 100.70-101.35% for the LC method and 98.48-98.65% for the UV spectrophotometric method. Statistical analysis by Student's t-test showed no significant difference between the results obtained by the 2 methods. The proposed methods are highly sensitive, precise, and accurate and can be used for the reliable quantitation of citalopram in tablets.     

A validated high-performance liquid chromatographic assay for determination of lumiracoxib in human plasma

Lumiracoxib {2-[(2-fluoro-6-chlorophenyl)amino]-5-methyl-benzeneacetic acid} is a highly selective and potent cyclooxygenase-2 (COX-2) inhibitor, which is chemically distinct from other coxibs in that it contains a carboxylic group and is weakly acidic. In the present study, a liquid-liquid extraction-based reversed-phase HPLC method with UV detection was validated and applied for the analysis of lumiracoxib in human plasma. The analyte was separated on a reversed-phase column with acetonitrile and 0.05% trichloracetic acid in water (35:65, v/v) as mobile phase at a flow rate of 1 mL/min, and UV detection at 270 nm. The retention times for lumiracoxib and niflumic acid (internal standard) were 16.9 and 10.4 min, respectively. The validated quantitation range for lumiracoxib was 10-10,000 ng/mL. The developed procedure was applied to assess the pharmacokinetics of lumiracoxib following administration of a single oral 200 mg dose to a healthy male volunteer.     

Reversed-phase liquid chromatographic determination of riboflavin in feeds

A method for determination of riboflavin in animal feeds using liquid chromatography (LC) was developed for feed samples fortified with riboflavin at 1 mg/lb or greater (up to 10,000 mg/lb). Feed samples were extracted in 0.1 N HCl with heating on a steam bath for 30 min, followed immediately by mechanical shaking for 30 min. Sample extracts were diluted to target volume with 2% acetic acid and filtered; riboflavin was determined by LC on a reversed-phase C18 column with 2% acetic acid-acetonitrile (85 + 15) mobile phase for separation and fluorescence detection with excitation at 460 nm and emission at 530 nm. The extraction was compared with that of the AOAC Official Method for riboflavin in food and feed premixes. The 2 method extractions were not significantly different from each other at the 95% confidence level. The developed method also had good linearity over 4 orders of magnitude, recovery of 95-99% from spiked feed samples, a limit of detection of riboflavin at 0.00034 microg/mL in solution, a limit of quantitation of 0.023 mg/lb in feed, and good ruggedness.     

High-performance liquid chromatographic analysis of steroid hormones

In the present work, a practical, rapid, reliable and isocratic reversed-phase high-performance liquid chromatographic (HPLC) method is described for the qualitative and quantitative analysis of estriol, estradiol-17 beta, estrone, testosterone, and progesterone. Chromatographic separation is complete in 16 min using a mobile phase of 50% acetonitrile (v/v) in water. The order of elution is estriol, testosterone, estradiol-17 beta, estrone, and progesterone; retention times are 2.5, 5.5, 5.6, 6.9, 16.3 min, respectively. Absorbance maxima of individual steroids is the limiting factor in quantitative determination. The recommended wavelengths for UV monitoring are E3 214, E2 280, T 254, E1 214, and P4 254 nm.     

Simultaneous LC Determination of Quercetin, Kaempferol and Isorhamnetin in Rabbits after Intragastric Administration of an Ethanol Extract from Pollen Typhae

A simple and rapid reversed-phase LC method was developed and validated for simultaneous determination of three flavonoids, quercetin (QU), kaempferol (KA) and isorhamnetin (IS), in rabbit blood plasma. The plasma was deproteinized using 10% trichloroacetic acid and extracted by n-butanol–acetoacetate solvent prior to LC analysis. The analyte was separated on a reversed-phase column with acetonitrile and 0.1% phosphoric acid in water (27:73, v/v) as mobile phase at a flow-rate of 0.8 mL min^?1, and UV detection wavelength at 369 nm. By this developed method, the concentrations of QU, KA and IS were linearly related to their responses in the range of 0.05–2.5 μg mL^?1. The precision and accuracy for QU, KA and IS in plasma were within ±15% except for the limit of quantitation (LOQ), where they were within ±20%. The validated method has been successfully applied in the pharmacokinetic study of QU, KA and IS in rabbits after intragastric administration of an ethanol extract from traditional Chinese medicine Pollen Typhae.     

Determination of aliskiren in tablet dosage forms by a validated stability-indicating RP-LC method

A reversed-phase liquid chromatography (RP-LC) method is validated for the determination of aliskiren in tablet dosage form. The LC method is carried out on a Waters XBridge C(18) column (150 × 4.6 mm i.d.), maintained at 25°C. The mobile phase consisted of acetonitrile:water (95:5, v/v)/phosphoric acid (25 mM, pH 3.0) (40:60, v/v), run at a flow rate of 1.0 mL/min, with photodiode array detector set at 229 nm. The chromatographic separation is obtained with aliskiren retention time of 3.68 min, and it is linear in the range of 10-300 μg/mL (r = 0.9999). The limits of detection and quantitation are 2.38 and 7.93 μg/mL, respectively. The specificity and stability-indicating capability of the method are proven through degradation studies, which also showed that there is no interference of the formulation excipients, showing that peak is free from any coeluting peak. The method showed adequate precision, with a relative standard deviation (RSD) values lower than 0.92%. Good values of accuracy were also obtained, with a mean value of 99.55%. Experimental design is used during validation to calculate method robustness. The proposed method is applied for the analysis of the tablet dosage forms, contributing to improve the quality control and to assure the therapeutic efficacy.     

High-performance liquid chromatographic determination of hippuric acid in human urine

A method is described for the determination of urinary hippuric acid by high-performance liquid chromatography. The method used ethyl acetate extraction for partial clean up of the urine. The separation was carried out on a reversed-phase column using 20% methanol in 0.01 M aqueous potassium phosphate containing 0.5% acetic acid as a mobile phase. The column effluent was monitored with a UV detector at 254 nm. Hippuric acid was separated from other normal urine constituents in less than 10 min. Metabolites of xylene and styrene did not interfere with the assay. Analytical recoveries from urine were excellent and peak height and concentration were linearly related.     

Validation of an HPLC method for quantitation of MDMA in tablets

An isocratic reversed-phase high-performance liquid chromatography (HPLC) method is developed and validated for the quantitation of 3,4-methylenedioxymethamphetamine (MDMA) in tablets. The chromatographic separation is achieved with potassium phosphate buffer (pH 3.2)-acetonitrile (9:1, v/v) as mobile phase, a Chromspher B column, and UV detection at 210 nm. The calibration curve is linear from 1.4 to 111 microg/mL. The percent relative standard deviation for intra- and interday precision studies is 2.7% each. The measurement uncertainty is estimated to 9%. The method is specific and successfully used for routine quantitation of MDMA in tablets.     

Methylammonium formate as a mobile phase modifier for totally aqueous reversed-phase liquid chromatography

Although alkylammonium ionic liquids (ILs) such as ethylammonium nitrate and ethylammonium formate have been used as mobile phase "solvents" for liquid chromatography (LC), we have shown that the IL methylammonium formate (MAF), in part because of its lower viscosity as compared to other ILs, can be an effective replacement for methanol (MeOH) in reversed-phase LC. Plots of log retention factor versus the fraction of MeOH and MAF in the mobile phase indicate quite comparable solvent strength slope values of 2.50 and 2.05, respectively. Using a polar endcapped C18 column, furazolidone and nitrofurantoin using 20% MAF-80% water could be separated in 22 min but no baseline separation is possible using MeOH as the modifier, even down to 10%. Suppression of silanol peak broadening effects by MAF is important, permitting a baseline separation of pyridoxine, thiamine, and nicotinamide using 5% MAF-95% water at 0.7 mL/min. Using 5% MeOH-95% water, severe peak broadening for thiamine is evident. The compatibility of MAF as a mobile phase modifer at the 5% level for LC with mass spectrometry detection of water-soluble vitamins is also shown.     

Determination of major phenolic compounds in water by reversed-phase liquid chromatography after pre-column derivatization with benzoyl chloride

A simple reversed-phase LC method capable of detecting ng/ml quantities of phenolic compounds in water is described. Pre-column derivatization with benzoyl chloride is used for the separation and determination o-cresol, m-cresol, p-cresol, phenol, resorcinol, catechol and hydroquinone in water. The benzoyl derivatives formed within in 15 min, were extracted with dietyl ether, and then analyzed by liquid chromatography with UV detection at 232 nm. With a mobile phase of acetonitrile-tetrahydrofuran-water (54:6:40, v/v) the seven derivatives were eluted in 15 min. The detection limits were between 0.05 and 0.50 ng/ml for 50 ml of a standard water sample. The method was applied to the analysis of phenols in wine and river water. The recovery of the derivatives from pure water was 81-94% with relative standard deviations of 2.5-5.0%.     

Direct determination of methionine sulfoxide in milk proteins by enzyme hydrolysis/high-performance liquid chromatography

A direct and simultaneous HPLC/UV determination of methionine and methionine sulfoxide in enzyme-hydrolyzed milk proteins is described. Protein hydrolysis is accomplished by a three-enzyme (pronase, leucine aminopeptidase, prolidase) 20-h/37 degrees C digestion. A gradient elution reversed-phase HPLC system with UV detection at 214 nm and 280 nm is then used to determine the quantitative releases of methionine sulfoxide, methionine, tyrosine, and tryptophan. The ease of methionine oxidation by a wide variety of oxidants, coupled with the quantitative release of both methionine and its sulfoxide by the three-enzyme hydrolysis, renders the approach valuable for identifying oxidized milk proteins. The relatively simple method proved accurate and precise in its application to commercial milk products, finding methionine sulfoxide levels as high as 74% of the total methionine.     

Liquid chromatographic analysis of vitamin B6 in soy-based infant formula

A liquid chromatographic (LC) method is described for determination of total vitamin B6 in soy-based infant formula. Total vitamin B6 is quantitated by using ion-pair LC after precolumn transformation of phosphorylated and free vitamers into pyridoxol. The limit of detection is 0.3 ng and the limit of quantitation is 1.0 ng on-column (injection volume = 100 microL). Linear response ranged from 39 to 616 ng/mL (r2 = 0.99986). Analysis of a soy-based infant formula control fortified at 6 different concentration levels gave recoveries that averaged 104%. Assay of SRM 1846 gave results within the certified range (8.6 +/- 0.086 mg/kg versus the certified value of 8.4 +/- 1.0 mg/kg). The method provides a rapid and specific assay for the analysis of total vitamin B6 in fortified soy-based infant formula.     

Qualitative and quantitative reversed-phase liquid chromatography of a new bisisoxazolylnaphthoquinone

The main objective of this study was to develop and test the applicability of a sensitive, accurate, and precise liquid chromatographic (LC) method for evaluating the stability characteristics of a new bisisoxazolylnaphthoquinone, 2-(3,5-dimethyl-4-isoxazolylamino)-N-(3,5-dimethyl-4-isoxazolyl)-1,4-naphthoquinone-4-imine compound 1. The method was shown to be selective and stability-indicating. Isocratic elution with a mobile phase of methanol-water (75 + 25, v/v) on a reversed-phase column with UV detection at ambient temperature completely resolved compound 1 from its degradation products. The LC system was calibrated by plotting peak responses versus known concentrations of a reference standard by using an internal standardization procedure. Complete elution occurred after 12 min with a peak symmetry factor of 0.95 for the drug peak. The kinetic degradation of compound 1 was studied over a pH range of 0.88-14.00 to determine the kinetic parameters involved in its decomposition path in aqueous solution.     

反相高效液相色谱法测定阿德福韦酯及其降解产物

建立了一快速、简单地测定阿德福韦酯及其降解产物阿德福韦单特戊酸甲基酯、阿德福韦的反相高效液相色谱方法。以Inertsil CN-3化学键合硅胶为固定相,以乙腈-25 mmol/L磷酸盐缓冲液(pH 4.0)(体积比为33∶67)为流动相,流速1.0 mL/min,检测波长260 nm。阿德福韦酯、阿德福韦的质量浓度分别为1.861~181.7 mg/L和2.018~197.2 mg/L时与峰面积呈良好的线性关系(r分别为0.9999和0.9998);阿德福韦酯及阿德福韦平均加样回收率分别为99.5%~10     

High Performance Liquid Chromatographic Analysis of Desipramine in Human Plasma Using a Microbore Column Technique

Abstract

A reversed-phase, isocratic HPLC method has been developed for the quantitation of desipramine in human plasma. the method involved the use of cloimpramine as an internal standard. the chromatographic separation was accomplished with a mobile phase comprising acetonitrile-aqueous solution (60:40. v/v) containing 10 mM disodium hydrogenphosphate and 80 mM sodium dodecyl sulfate adjusted to pH 2. the mobile phase was pumped at a flow rate of 0.5 ml/min. the column used was a microbore column (2 mm I.D. × 100 mm) packed with a C18 reversed-phase material (5μm ODS Hypersil). Plasma samples were extracted at basic pH with diethyl ether followed by back-extraction into 0.1 N sulfuric acid. Using UV detection at 250 nm, the lower limit of sensitivity was 10 ng/ml. the inter- and intra-assay coefficients of variation were found to be less than 10%. the assay procedure was applied to a long term oral dosing study in patients to monitor the plasma concentration of desipramine.     

Single-laboratory validation of a liquid chromatographic/tandem mass spectrometric method for the determination of free and total carnitine in infant formula and raw ingredients

A reversed-phase liquid chromatographic/tandem mass spectrometric method was developed and validated for the determination of free carnitine (FC) and total carnitine (TC) in infant formula and raw ingredients. Preparation of samples for FC determination required only nonvolumetric dilution in water, followed by filtration. Determination of TC in whey-based samples required a common saponification procedure, which hydrolyzed the acylcarnitines to FC. L-Carnitine standards were prepared in water at 3 concentrations (7.5, 30, and 60 ng/mL). L-Carnitine-d3 was incorporated in the sample and standard preparations as a stable isotope internal standard (ISTD), which helped to normalize signal suppression due to fouling of the ionization source, or matrix effects. A short C8 column (50 x 2.1 mm id) was used for liquid chromatography, with mobile phases consisting of 0.1% heptafluorobutyric acid in water and methanol. L-Carnitine and the ISTD eluted at about 2 min, and the injection-to-injection cycle time was about 11 min. Multiple-reaction monitoring was used for quantitation by monitoring the ion transitions m/z 162 > 103 and 162 > 85 for L-carnitine, and m/z 165 > 103 and 165 > 85 for the ISTD. The values for overall method precision for a whey-based infant formula, a protein hydrolyzate infant formula, and a water-soluble vitamin/amino acid premix were relative standard deviations of 1.32, 1.86, and 3.33%, respectively. The overall mean recoveries were between 97.3 and 102.8%. Additionally, the method results showed good correlation with those obtained for a radioenzymatic assay done in-house.     

整体柱离子对色谱-间接紫外检测法快速测定N-甲基,丙基吗啉阳离子

建立了快速分析无紫外吸收的N-甲基,丙基吗啉阳离子的离子对色谱-间接紫外检测法。采用反相C18硅胶整体柱,以背景紫外吸收试剂-离子对试剂-有机溶剂为流动相。研究了背景紫外吸收试剂、检测波长、离子对试剂、有机溶剂、柱温、流速对吗啉阳离子测定的影响。最佳色谱条件为:(0.5 mmol/L对氨基苯酚盐酸盐-0.1 mmol/L庚烷磺酸钠)溶液-甲醇(9:1, v/v)为流动相,检测波长230 nm,柱温30 ℃,流速1.0 mL/min。在此条件下,N-甲基,丙基吗啉阳离子的保留时间为2.966 min,检出限为0.07 mg/L(S/N=3),峰面积的相对标准偏差为2.1%(n=5),保留时间的相对标准偏差为0.02%(n=5)。将此方法用于分析实验室合成的N-甲基,丙基吗啉离子液体,加标回收率为98.8%。结果表明本方法简便、快速。     

Effects of first dimension eluent composition in two-dimensional liquid chromatography

Comprehensive two-dimensional liquid chromatography (LC×LC) has received a great deal of attention during the past few years because of its extraordinary resolving power. The biggest advantage of this technique is that very high peak capacities can be generated in a relatively short time. Numerous approaches to maximize the peak capacity in LC×LC have been employed. In this work we investigate the impact of the first dimension mobile phase on selectivity. LC×LC has several potential advantages over one-dimensional LC (1DLC) in that unconventional solvents, at least in reversed-phase LC, can be used. For example, solvents which strongly adsorb in the UV in the first dimension are not problematic in LC×LC. This so because the UV detector is placed after the second dimensional column, as pulses of the first dimension eluent arrive at the second dimensional column, they elute well before the solutes of interest and therefore do not interfere at all with detection of solute peaks. So far, the most widely used solvents in reversed-phase 1DLC are methanol and acetonitrile. However, the "UV advantage" of 2DLC allows us to employ UV active solvents, such as acetone. We compare their differential selectivities to that of acetonitrile for the separation of 23 indole acetic acids of interest in plant biology. We also apply them to the separation of a maize seed extract, a very complex sample. In both sample sets, mobile phase composition can be an important parameter to increase the orthogonality of the two dimensions and thus, to increase the effective peak capacity of LC×LC.