Effects of Sc2O3 and MgO passivation layerson the output power of AlGaN/GaN HEMTs

The low temperature (100°C) deposition of Sc₂O₃ or MgO layers is found to significantly increase the output power of AlGaN/GaN HEMTs. At 4 GHz, there was a better than 3 dB increase in output power of 0.5×100 μm² HEMTs for both types of oxide passivation layers. Both Sc₂ O₃ and MgO produced larger output power increases at 4 GHz than conventional plasma-enhanced chemical vapor deposited (PECVD) SiN_x passivation which typically showed ⩽2 dB increase on the same types of devices. The HEMT gain also in general remained linear over a wider input power range with the Sc₂O₃ or MgO passivation. These films appear promising for reducing the effects of surface states on the DC and RF performance of AlGaN/GaN HEMTs     

Influence of layer structure on performance of AlGaN/GaN high electron mobility transistors before and after passivation

Intentionally undoped and three different, doped layer structures are used to investigate properties of AlGaN/GaN high electron mobility transistors (HEMTs) before and after SiN passivation. For unpassivated devices, the drain current, transconductance, cutoff frequency, and microwave output-power increase with increased doping level, in spite of an increase in the gate-leakage current. After passivation, an overall performance improvement of all devices occurs. The passivation-induced sheet charge decreases from 2×10¹² cm⁻² in undoped structures to ∼0.7×10¹² cm⁻² in higher doped structures and performance improvement with passivation is less pronounced for higher doped devices. However, the output power of unpassivated and passivated devices on higher doped structures is much higher than that on the undoped-passivated counter-part. These results underline an advantage of the doped layer structure for the preparation of high-performance AlGaN/GaN HEMTs.     

蓝宝石衬底上使用氮化硅钝化的AlGaN/GaN高电子迁移率晶体管的研制与特性分析

本文研制了高性能的AlGaN/GaN高电子迁移率晶体管并进行了特性分析。诸如氮化铝插入层、氮化硅钝化、高宽窄比的T型栅、减小欧姆接触电阻和缩短漏源距离等技术被用于提高器件性能。使用半导体参数分析仪和矢量网络分析仪分别对前制器件的直流和交流特性进行了表征。所得80nm栅长的器件其最大漏极电流密度为1.41A/mm,该结果为到目前为止国内文献报道的最大值。同时测得峰值跨导为317mS/mm,特征频率为74.3GHz,最高振荡频率为112.4GHz。     

Fabrication and characterization of high performance AlGaN/GaN HEMTs on sapphire with silicon nitride passivation

AlGaN/GaN high electron mobility transistors(HEMTs)with high performance were fabricated and characterized.A variety of techniques were used to improve device performance,such as AlN interlayer,silicon nitride passivation,high aspect ratio T-shaped gate,low resistance ohmic contact and short drain-source distance. DC and RF performances of as-fabricated HEMTs were characterized by utilizing a semiconductor characterization system and a vector network analyzer,respectively.As-fabricated devices exhibited a maximum drain current density of 1.41 A/mm and a maximum peak extrinsic transconductance of 317 mS/mm.The obtained current density is larger than those reported in the literature to date,implemented with a domestic wafer and processes.Furthermore, a unity current gain cut-off frequency of 74.3 GHz and a maximum oscillation frequency of 112.4 GHz were obtained on a device with an 80 nm gate length.     

Traps centers and deep defects contribution in current instabilities for AlGaN/GaN HEMT's on silicon and sapphire substrates

AlGaN/GaN high electron mobility transistors (HEMTs) with Si and Al₂O₃ substrates reveals anomalies on I_ds-V_ds-T and I_gs-V_gs-T characteristics (degradation in drain current, kink effect, barrier height fluctuations, etc.). Stress and random telegraph signal (RTS) measurements prove the presence of trap centers responsible for drain current degradation. An explanation of the trapping mechanism responsible for current instabilities is proposed. Deep defects analysis performed by capacitance transient spectroscopy (C-DLTS), frequency dispersion of the output conductance (G_ds(f)), respectively, on gate/source and drain/source contacts and RTS prove the presence of deep defects localized, respectively, in the gate and in the channel regions. Defects detected by C-DLTS and G_ds(f) are strongly correlated, respectively, to barrier height inhomogeneities and kink anomalies. Gate current analysis confirms the presence of (G-R) centers acting like traps at the interface GaN/AlGaN. Finally, the localization of these traps defects is proposed.     

Comparative study of AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors with Al2O3 and HfO2 gate oxide

AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors (MOSHFETs) with Al₂O₃ gate oxide which was deposited by atomic layer deposition (ALD) were fabricated and their performance was then compared with that of AlGaN/GaN MOSHFETs with HfO₂ gate oxide. The capacitance (C)-voltage (V) curve of the Al₂O₃/GaN MOS diodes showed a lower hysteresis and lower interface state density than the C-V curve of the HfO₂/GaN diodes, indicating better quality of the Al₂O₃/GaN interface. The saturation of drain current in the I_D-V_GS relation of the Al₂O₃ AlGaN/GaN MOSHFETs was not as pronounced as that of the HfO₂ AlGaN/GaN MOSHFETs. The gate leakage current of the Al₂O₃ MOSHFET was five to eight orders of magnitude smaller than that of the HfO₂ MOSHFETs.     

The effects of gate length variation and trapping effects on the transient response of AlGaN/GaN HEMT’s on SiC substrates

In AlGaN/GaN heterostructure field-effect transistors, the surface defects and dislocations may serve as trapping centers and affect the device performance via leakage current. In this paper we report results of our investigation of the trapping characteristics of Al_0.25Ga_0.75N/GaN HEMT using the Conductance Deep Level Transient Spectroscopy (CDLTS). Two deep level electronic defects were observed labeled E₁ and HL₁, with activation energies E_a1 = 1.36 eV and E_a2 = 0.63 eV. The hole-trap HL₁ is characterized for the first time in our studies. We identified the characteristics of the traps at the AlGaN/GaN interface adjoining the channel and the surface along the ungated region between the gate and the drain, as well as the effects of the surface traps.     

采用ALD Al2O3作为栅介质的薄势垒增强型AlGaN/GaN MIS-HEMT

本文报道了高性能的增强型（E-mode）氮化镓（GaN）基金属-绝缘体-半导体高电子迁移率晶体管（MIS-HEMT）,该器件势垒层为5-nm厚的铝镓氮（Al0.3Ga0.7N）,并采用氮化硅（SiN）钝化来控制二维电子气（2DEG）密度。与SiN钝化不同,采用原子层淀积（ALD）技术生长的氧化铝（Al2O3）不会增强异质结中的2DEG密度。刻蚀栅区的SiN介质可以耗尽沟道电子,之后采用ALD Al2O3作为栅介质,可以实现MIS结构。栅长为1 μm的E-mode MIS-HEMT具有657mA/mm的最大饱和电流（IDS）、187mS/mm的最大跨导（gm）和1V的阈值电压（Vth）。与相应的E-mode HEMT对比,由于Al2O3栅介质的引入,使器件的性能得到了很大的提升。本文对于同时实现高的Vth和IDS提供了很好的方法。     

Effect of PECVD of SiO2 passivation layers on GaN and InGaP

Thin (200 ) layers of SiO₂ were deposited by plasma enhanced chemical vapor deposition onto GaN and InGaP patterned with transmission line measurement contact pads. The sheet resistance of n-GaN and n- and p-InGaP was measured as a function of N₂O/SiH₄ ratio, rf chuck power, pressure and substrate temperature during the SiO₂ deposition. The sheet resistance ratio before and after the deposition varied from 0.7 to 1.2, reflecting a competition between mechanisms that decrease doping (hydrogen passivation, ion-induced deep traps) and those that increase it (creation of shallow donor states in n-type material through preferential ion of the group V elements, gettering of hydrogen in p-type material). Under most conditions, SiO₂ deposition creates minimal changes to the electrical properties of GaN and InGaP.     

原子层沉积氧化铝薄膜对多晶太阳能电池表面钝化的影响

A stack of Al2O3/SiNx dual layer was applied for the back side surface passivation of p-type multi-crystalline silicon solar cells, with laser-opened line metal contacts, forming a local aluminum back surface field （local Al-BSF） structure. A slight amount of Al2O3, wrapping around to the front side of the wafer during the thermal atomic layer deposition process, was found to have a negative influence on cell performance. The different process flow was found to lead to a different cell performance, because of the Al2O3 wrapping around the front surface. The best cell performance, with an absolute efficiency gain of about 0.6% compared with the normal full Al-BSF structure solar cell, was achieved when the Al2O3 layer was deposited after the front surface of the wafer had been covered by a SiNx layer. We discuss the possible reasons for this phenomenon, and propose three explanations as the Ag paste, being hindered from firing through the front passivation layer, degraded the SiNx passivation effect and the Al2O3 induced an inversion effect on the front surface. Characterization methods like internal quantum efficiency and contact resistance scanning were used to assist our understanding of the underlying mechanisms.     

GaN薄膜电子声成像和电子背散射衍射研究

采用扫描电声显微镜(SEAM)和电子背散射衍射(EBSD)对异质外延在Al2O3衬底上GaN界面区域成像测试分析。异质外延失配应力导致在Al2O3和GaN界面附近的微区晶格畸变在SEAM的声成像中可以清楚看到,而且受应力影响集中区域的微区衬度差异明显。利用EBSD色带图及质量参数分析了失配应力变化,晶格应变和弹性形变在200nm内可以得到释放。     

The influence of 1 nm AlN interlayer on properties of the Al0.3Ga0.7N/AlN/GaN HEMT structure

The sheet carrier concentrations, conduction band profiles and amount of free carriers in the barriers have been determined by solving coupled Schrödinger and Poisson equation self-consistently for coherently grown Al_0.3Ga_0.7N/GaN and Al_0.3Ga_0.7N/AlN/GaN structures on thick GaN. The Al_0.3Ga_0.7N/GaN heterojunction structures with and without 1 nm AlN interlayer have been grown by MOCVD on sapphire substrate, the physical properties for these two structures have been investigated by various instruments such as Hall measurement and X-ray diffraction. By comparison of the theoretical and experimental results, we demonstrate that the sheet carrier concentration and the electrons mobility would be improved by the introduction of an AlN interlayer for Al_0.3Ga_0.7N/GaN structure. Mechanisms for the increasing of the sheet carrier concentration and the electrons mobility will be discussed in this paper.     

Influence of dual-frequency plasma-enhanced chemical-vapor deposition Si<Subscript>3</Subscript>N<Subscript>4</Subscript> passivation on the electrical characteristics of AlGaN/GaN heterostructure field-effect transistors

The influence of dielectric stress on the direct current (DC) electrical characteristics of AlGaN/GaN heterostructure field-effect transistors (HFETs) has been investigated. Dual-frequency plasma deposition was used to vary the amount of stress induced by a passivating dielectric on the surface of the devices. Initial data suggested a strong influence from the induced dielectric stress, but the low-frequency, radio-frequency (RF) excitation of the plasma deposition process was found to induce a severe nonreversible damage to the exposed AlGaN surface through N ion bombardment. The consequence is a drastic reduction of the sheet carrier concentration and mobility of the two-dimensional electron gas (2DEG). Subsequently, an alternative damage-free technique using a helium precursor was used to obtain compressive films. Based on the results, uniform dielectric stress has a minimal impact on the polarization charges within the AlGaN barrier.     

Effects of surface passivation during atomic layer deposition of Al2O3 on In0.53Ga0.47As substrates

In this work we investigate the effect of different III-V surface passivation strategies during atomic layer deposition of Al₂O₃. X-ray photoelectron spectroscopy indicates that bare As-decapped and sulfur passivated In_0.53Ga_0.47As present residual oxides on the surface just before the beginning of the Al₂O₃ deposition while the insertion of a Ge interface passivation layer results in an almost oxide free Ge/III-V interface. The study of the initial growth regimes, by means of in situ spectroscopic ellipsometry, shows that the growth of Al₂O₃ on Ge leads to an enhanced initial growth accompanied by the formation of Ge-O-Al species thus affecting the final electrical properties of the stack. Alternatively, deposition on decapped and S-passivated In_0.53Ga_0.47As results in a more controlled growth process. The sulfur passivation leads to a better electrical response of the capacitor that can be associated to a lower oxide/semiconductor interface trap density.     

Atomic-layer-deposited Al2O3 and HfO2 on GaN: A comparative study on interfaces and electrical characteristics

Al₂O₃, HfO₂, and composite HfO₂/Al₂O₃ films were deposited on n-type GaN using atomic layer deposition (ALD). The interfacial layer of GaON and HfON was observed between HfO₂ and GaN, whereas the absence of an interfacial layer at Al₂O₃/GaN was confirmed using X-ray photoelectron spectroscopy and transmission electron microscopy. The dielectric constants of Al₂O₃, HfO₂, and composite HfO₂/Al₂O₃ calculated from the C-V measurement are 9, 16.5, and 13.8, respectively. The Al₂O₃ employed as a template in the composite structure has suppressed the interfacial layer formation during the subsequent ALD-HfO₂ and effectively reduced the gate leakage current. While the dielectric constant of the composite HfO₂/Al₂O₃ film is lower than that of HfO₂, the composite structure provides sharp oxide/GaN interface without interfacial layer, leading to better electrical properties.     

Comparison of interfacial and electrical properties between Al2O3 and ZnO as interface passivation layer of GaAs MOS device with HfTiO gate dielectric

GaAs metal–oxide–semiconductor(MOS) capacitors with HfTiO as the gate dielectric and Al2O3 or ZnO as the interface passivation layer(IPL) are fabricated. X-ray photoelectron spectroscopy reveals that the Al2O3 IPL is more effective in suppressing the formation of native oxides and As diffusion than the ZnO IPL. Consequently, experimental results show that the device with Al2O3 IPL exhibits better interfacial and electrical properties than the device with ZnO IPL: lower interface-state density(7.21012 eV1cm2/, lower leakage current density(3.60107A/cm2 at Vg D1 V) and good C–V behavior.     

Towards metal electrode interface scavenging of rare-earth scandates: A Sc2O3 and Gd2O3 study

Amorphous Gd₂O₃ and Sc₂O₃ thin films were deposited on Si by high-pressure sputtering (HPS). In order to reduce the uncontrolled interfacial SiO_x growth, firstly a metallic film of Gd or Sc was sputtered in pure Ar plasma. Subsequently, they were in situ plasma oxidized in an Ar/O₂ atmosphere. For post-processing interfacial SiO_x thickness reduction, three different top metal electrodes were studied: platinum, aluminum and titanium. For both dielectrics, it was found that Pt did not react with the films, while Al reacted with them forming an aluminate-like interface and, finally, Ti was effective in scavenging the SiO₂ interface thickness without severely compromising gate dielectric leakage.     

Effective passivation of defects in Ge-rich SiGe-on-insulator substrates by Al2O3 deposition and subsequent post-annealing

A method of Al₂O₃ deposition and subsequent post-deposition annealing (Al₂O₃-PDA) was proposed to passivate electrically active defects in Ge-rich SiGe-on-insulator (SGOI) substrates, which were fabricated using Ge condensation by dry oxidation. The effect of Al₂O₃-PDA on defect passivation was clarified by surface analysis and electrical evaluation. It was found that Al₂O₃-PDA could not only suppress the surface reaction during Al-PDA in our previous work [Yang H, Wang D, Nakashima H, Hirayama K, Kojima S, Ikeura S. Defect control by Al-deposition and the subsequent post-annealing for SiGe-on-insulator substrates with different Ge fractions. Thin Solid Films 2010; 518: 2342-5.], but could also effectively passivate p-type defects generated during Ge condensation. The concentration in the range of 10¹⁶-10¹⁸ cm⁻³ for defect-induced acceptors and holes in Ge-rich SGOI drastically decreased after Al₂O₃-PDA. As a result of defect passivation, the electrical characteristics of both back-gate p-channel and n-channel metal-oxide-semiconductor field-effect transistors fabricated on Ge-rich SGOI were greatly improved after Al₂O₃-PDA.     

Optimization of Al2O3/ZrO2 nanolaminate structure for thin-film encapsulation of OLEDs

We report thin-film moisture barriers based on Al₂O₃/ZrO₂ nanolaminates grown by ALD for an encapsulation of OLEDs. In order to optimize the moisture-barrier performance of the nanolaminates, the most important factors affecting the performance were sought by measuring WVTR of the nanolaminates via an electrical Ca test. We found out that both the number of interfaces in the nanolaminates and the thickness of ZrO₂ in a unit layer were responsible for the performance. By optimizing the nanolaminate structure, the moisture-barrier performance was enhanced up to 350% from a single layer of the same thickness. The WVTR of 30-nm-thick optimized nanolaminate barrier was 2 × 10⁻⁴ g/(m² day) or less at ambient condition. A storage-lifetime measurement of an OLED with a 100-nm-thick encapsulation layer showed that it could exceed 70,000 h if stored at ambient condition.     

高效太阳电池硅衬底特性对原子层沉积Al2O3薄膜钝化性能的影响

Atom layer deposition （ALD）-Al2O3 thin films are considered effective passivation layers for p-type silicon surfaces. A lower surface recombination rate was obtained through optimizing the deposition parameters. The effects of some of the basic substrate characteristics including material type, bulk resistivity and surface morphology on the passivation performance of ALD-Al2O3 are evaluated in this paper. Surface recombination velocities of 7.8 cm/s and 6.5 cm/s were obtained for p-type and n-type wafers without emitters, respectively. Substrates with bulk resistivity ranging from 1.5 to 4 Ω · cm were all great for such passivation films, and a higher implied Voc of 660 mV on the 3 Ω · cm substrate was achieved. A minority carrier lifetime （MCL） of nearly 10 μs higher was obtained for cells with a polished back surface compared to those with a textured surface, which indicates the necessity of the polishing process for high-efficiency solar cells. For n-type semi-finished solar cells, a lower effective front surface recombination velocity of 31.8 cm/s was acquired, implying the great potential of （ALD）-Al2O3 thin films for high-efficiency n-type solar cells.