The Spectrophotometry Determination of Mn(III) in the Presence of Mn(IV)

Abstract

The spectra of complex of Mn(III) and Mn(IV) with pyrophosphoric acid are investigated. The molar absorption coefficient of the complex of Mn(III) with pyrophosphoric acid is 80.6/Mcm at 510nm which is close to that of Mn(IV), 110/Mcm, however, the molar absorption coefficient of the complex of Mn(HI) with pyrophosphoric acid is only 4.98/Mcm at 398nm which is much less than that of Mn(IV), 390/Mcm. Based on this absorbance difference between Mn(III) and Mn(IV) at wavelength 398nm and 510nm, a procedure of determination of Mn(III) in the presence of Mn(IV) has been developed.     

On-line precipitation/dissolution system for the preconcentration and determination of manganese traces by atomic absorption spectrometry

Flame atomic absorption spectrometry was used for the determination of Mn in biological material following preconcentration by precipitation. The proposed preconcentration method is based on the continuous precipitation of Mn(II) as hydrated Mn(IV) oxide in ammonia buffer and dissolution of the precipitate with hydrogen oxalate or dilute nitric acid. The sensitivity of the Mn determination is increased by the presence of hydrogen peroxide, which raises the rate of oxidation of Mn(II) to Mn(IV). By using a time-based technique (at a sample loading rate of 4 ml min⁻¹) a concentration factor of up to 55 was obtained using 24 ml of sample. The effect of concurrent cations was investigated; the most adverse effect was exerted by Fe(III), which interfered at concentrations 50 times higher than that of Mn(II).     

Optimization of the Sample Preparation Procedure for the Determination of Trace Elements in Auricularia auricula by Inductively Coupled Plasma-Optical Emission Spectrometry

This study aimed to develop a precise and accurate method of sample preparation of Auricularia auricula for inductively coupled plasma-optical emission spectrometry-based trace element determination and to compare concentrations of seven trace elements (Mg, Fe, Mn, Zn, Ni, Cr, Sr) in six A. auricula samples belonging to three varieties with two cultivation substrates. Five sample preparation procedures, microwave-assisted digestion, nitric acid digestion with hot plate heating, nitric acid and perchloric acid digestion with hot plate heating, nitric acid digestion with ash content, and aqua regia digestion with ash content, were compared. The performance of the procedures was determined based on the precision and accuracy of the results and the limits of detection of the elements. The best results, with limits of detection of 0.60–6.60?ng?·?mL^?1 and recoveries for spiked samples between 93.80 and 105.00%, were found using nitric acid digestion with ash content. Six A. auricula samples were analyzed using the proposed procedure. Among the tested elements, the concentration of Fe was highest in all six A. auricula samples up to a maximum concentration of 284.83?µg?·?g^?1. The concentrations of Mn, Cu, and Ni increased in mixed stands (basswood, birch, and mongolica) compared with pine sawdust cultivation.     

Multielemental Analysis of Human Serum by Dynamic Reaction Cell–Inductively Coupled Plasma Mass Spectrometry

The selection of the most suitable dilution methods for determination of trace elements in human serum using inductively coupled plasma mass spectrometry is reported. The trace elements were Al, V, Cr, Fe, Mn, Co, Cu, Zn, As, Cd, Sn, Tl, and Pb. The performance of various dilution methods was assessed by precision, linearity, detection limits, quantification limits, fortified recoveries, and the analysis of reference materials. The results demonstrate that diluted solution containing only nitric acid is most suitable for As, Cr, Mn, and Co in serum. Dilute solutions containing nitric acid and Triton X-100 were most appropriate for Cu, Zn, Cd, and Tl. The optimum conditions for Al, V, Mn, Fe, Cr, Co, Sn, and Pb used tetra-n-butylammonium hydroxide, Triton X-100, and ethylenediamine tetraacetic acid.     

Determination of lead and manganese in biological samples and sediment using slurry sampling and flame atomic absorption spectrometry

A procedure was developed for the determination of lead (Pb) and manganese (Mn) using slurry sampling. The two elements were detected using flame atomic absorption spectrometry with a slotted tube atom trap. Slurries were prepared by adding nitric acid solution (0.30%, w/v) to a powdered sample (0.10 g). After homogenization by ultrasonic bath for 15 min, the slurries were introduced directly into the detection equipment. Some conditions of the procedure were evaluated, such as acid concentration, presence of surfactants, and sonication time. Under optimized conditions, the LODs and LOQs achieved were 0.8 and 2.6 microg/g for Pb and 0.5 and 1.6 microg/g for Mn, respectively. The precision obtained varied between 3.1 and 5.8% (Mn), and 2.6 and 5.4% (Pb) for slurries of shrimp and sediment. The analytical curves were established using aqueous standards in nitric acid solutions. The accuracy of the method was assessed through the determination of Pb and Mn in the following certified reference materials: ERM-CE 278 (mussel tissue), CRM 397 (human hair), and SRM 1646a (estuarine sediment). The proposed procedure was successfully applied to the determination of Pb and Mn in six samples of shrimp powder, seasoning, and river sediment. The levels of Mn detected varied from 2.2 to 71.3 microg/g; Pb was detected in only one sediment sample (4.3 microg/g).     

Determination of trace elements in Syrian medicinal plants and their infusions by energy dispersive X-ray fluorescence and total reflection X-ray fluorescence spectrometry

X-ray fluorescence (XRF) and total-reflection X-ray fluorescence (TXRF) techniques suited well for a multi-element determination of K, Ca, Mn, Fe, Cu, Zn, Rb, and Sr in some Syrian medicinal plant species. The accuracy and the precision of both techniques were verified by analyzing the Standard Reference Materials (SRM) peach-1547 and apple leaves-1515. A good agreement between the measured concentrations of the previously mentioned elements and the certified values were obtained with errors less than 10.7% for TXRF and 15.8% for XRF. The determination of Br was acceptable only by XRF with an error less than 24%. Furthermore, the XRF method showed a very good applicability for the determination of K, Ca, Mn, Fe, Cu, Zn, Rb, Sr, and Br in infusions of different Syrian medicinal plant species, namely anise (Anisum vulgare), licorice root (Glycyrrhiza glabra), and white wormwood (Artemisia herba-alba).     

Electrocatalytic Determination of Vitamin C Using Calixarene Modified Carbon Paste Electrodes

Effect of in situ complexation of some ions with variable valencies, like Co(II), Ni(II), Mn(II), Cu(II) and Pb(II) on the the electrooxidation of Vitamin C (L ‐ascorbic acid) was studied by cyclic voltammetry using carbon paste electrodes modified with p‐tert‐butylcalix[4]arene and p‐tert‐butylcalix[6]arene in perchloric acid, acetic acid and ammonium acetate media. Pb(II) was found to bind strongly with p‐tert‐butylcalix[4]arene in acetate medium, resulting in its being retained at the electrode surface and catalyzing the oxidation of ascorbic acid. The overpotential was reduced by about 200 mV with an increase in the peak currents. Linearity was observed over the range of 0.07–400 ppm with a detection limit of 30 ppb by differential pulse voltammetry. Interferences of some common substances like sugars and amino acids were studied and the modified electrode was used for the determination of vitamin C in commercial samples.     

Atomic absorption spectrometry for the automatic indirect determination of ascorbic acid based on-the reduction of manganese dioxide.

A new and simple flow injection method followed by atomic absorption spectrometry has been developed for the indirect determination of ascorbic acid. The proposed method is based on oxidation of ascorbic acid to dehydroascorbic acid using a solid-phase manganese dioxide (30% m/m suspended on silica gel beads) reactor. The flow of the sample through the column reduces the MnO2 to Mn(II) in an acidic carrier stream of 6.3 mM HNO3 (pH 2.2) with flow rate of 4.0 ml/min at room temperature; Mn(II) is measured by atomic absorption spectrometry. The absorbance of Mn(II) is proportional to the concentration of ascorbic acid in the sample. The calibration curve was linear up to 30 mg/L, with a detection limit of 0.2 mg/L for a 220 microL injected sample volume. The developed procedure was found to be suitable for the determination of AsA in pharmaceuticals and foods with a relative standard deviation better than 1.09% and a sampling rate of about 95 h(-1). The results exhibit no interference from the presence of large amounts of organic compounds. The reliability of the method was established by parallel determination against the 2,6-dichlorophenol-indophenol methods.     

Synthesis and Study of Unsymmetrical Schiff Base Mn(III) Complexes with Pendant Aza-crown or Morpholino Groups as Catalyst in Aerobic Oxidation for p-Xylene to p-Toluic Acid

A series of novel unsymmetrical Schiff base Mn(III) complexes with pendant aza-crown or morpholino groups have been synthesized and studied as catalysts in aerobic oxidation of `p-xylene to p-toluic acid (PTA). The oxidation of p-xylene to p-toluic acid with air at 120°C under normal atmospheric pressure occurred efficiently in the presence of aza-crown ether substituted unsymmetrical Schiff base Mn(III) complexes. Significant selectivity (up to ～90%) and conversion levels (up to ～40%) were obtained. The effect of the aza-crown ring appended in Mn(III) Schiff base complexes on the oxidation of p-xylene were also investigated by comparison with the morpholino group pendant analogues. The addition of alkali metal ions accelerates the rate of conversion of p-xylene to p-toluic acid.     

Catalytic determination of nanogram amounts of Mn(II) by the aerial oxidative coupling reaction of 3-methyl-2-benzothiazolinone hydrazone with N,N-dimethylaniline

Summary A new catalytic method for the determination of nanogram level of Mn(II) is developed, which is based on its catalytic effect on the aerial oxidative coupling reaction of 3-methyl-2-benzothiazolinone hydrazone (MBTH) withN, N-dimethylaniline (DMA) to form an indamine dye (_max=590 nm) in the presence of 1,10-phenanthroline (phen) as an activator. A detection limit of <0.05 ng Mn(II)/ml can be achieved and as low as 10^–9 M Mn(II) can easily be determined by measuring the absorbance of the dye at a fixed time (50 min at 30° C). The proposed method was successfully applied to the determination of manganese in natural waters by using 0.02–4 ml of water samples without preconcentration and separation.     

Synthesis,characterization and crystal structure of a novel three-dimensional supramolecular architecture formed by manganese(II) and pyridine-2,5-dicarboxylic acid

A novel three-dimensional supramolecular compound formed by Mn(II) and pyridine-2,5-dicarboxylic acid of formula [Mn(Pydc)₂(H₂O)₂] (Pydc?=?pyridine-2,5-dicarboxylic acid) has been synthesized and characterized by elemental analyses, IR, electronic spectra, thermogravimetric analysis and X-ray diffraction techniques. The X-ray structure shows that the central Mn(II) ion is coordinated by two water molecules and two chelated Pydc ligands. Water molecules coordinate with Mn(II) ions in the cis mode. Intermolecular hydrogen bonds play an important role in stabilization of the lattice and construction of the supramolecular network.     

Atomabsorptionsspektrophotometrische Bestimmung von Kobalt,Kupfer, Mangan und Zink in Multivitaminpräparaten nach Abtrennung mittels Anionenaustausches

Zusammenfassung Eine störungsfreie Methode zur Bestimmung von Kobalt, Kupfer, Mangan und Zink in Multivitaminpräparaten unter Anwendung der Atomabsorptionsspektrophotometrie wurde beschrieben. Nach dem Auflösen der Probe in konz. Salzsäure werden die genannten Elemente auf einer Säule des stark basischen Anionenaustauschers Dowex 1 adsorbiert, und zwar aus einer Mischung von 50 Vol.% Hexon, 40 Vol.% Isopropanol und 10 Vol.% 12-m Salzsäure. Dadurch werden sie von Matrixbestandteilen (z. B. Eisen und organischen Substanzen) getrennt und sind dann nach Elution mit 6-m Salzsäure (Co, Cu und Mn) und 2-m Salpetersäure (Zink) quantitativ bestimmbar. Die Methode wurde zur Analyse von 5 Multivitaminpräparaten herangezogen.

---

Atomic absorption spectrophotometric determination of cobalt, copper, manganese and zinc in multivitamin preparations after separation by means of anion exchange

Summary A trouble-free method of determining cobalt, copper, manganese and zinc in multivitamin preparations using atomic absorption spectrophotometry is described. After dissolving the sample in concentrated hydrochloric acid the elements specified are adsorbed on a column of the strongly basic anion exchanger Dowex 1 (from a mixture of 50 vol% hexon, 40 vol% isopropanol and 10 vol% 12M hydrochloric acid). They are thereby separated from matrix components (e. g. iron and organic substances) and can then be determined quantitatively after elution with 6M hydrochloric acid (Co, Cu and Mn) and 2M nitric acid (Zn). The method was used to analyse five multivitamin preparations.

     

Ion-Exchange Separtion and Determination of Mn,Co, Zn and Ni with Xylenol Orange as Post-Column Reagent

ABSTRACT

A method for the simultaneous determination of Mn, Co, Zn and Ni which combines Ion-chromatography and a post column reaction with xylenol orange is described. Using 0.07 M oxalic acid (pH adjusted to 5.5 with lithium hydroxide) as eluent, Mn, Co, Zn and Ni were first separated on a 4x250mm IonpacCS-5 column having both sulphonic acid and Alkyl quaternary ammonia functional groups and then transferred to a post-column reaction coil, where the elements react with xylenol orange. The coloured complexes formed were spectrophotometrically measured at 570 nm. The procedure has been successfully applied for the determination of Co, Zn and Ni in Al-bronze.     

Isophthaldihydroxamic acid as analytical reagent: Spectrophotometric determination of manganese

The reactivity of isophthaldihydroxamic acid against inorganic ions is established. The spectrophotometric study of its reaction with Mn(II) shows that a complex of stoichiometry 1:2 (Mn:L) is formed (? = 3760 liters · mol^?1 · cm^?1 at 490 nm). A spectrophotometric method is developed for the determination of manganese in the range 3–9 ppm.     

Mn(III)‐Mediated Chlorination of Conjugated Ketones

Mn(III)‐Cl formed by the reaction of Mn(OAc)₃ and hydrochloric acid in situ, reacted with α,β‐unsaturated ketones readily to afford α,β‐dichloroketones in good yields under mild conditions. The products are key precursors for synthesis of conjugated alkynones and other organic compounds.     

An Efficient Aerobic Oxidation for p-Xylene to p-Toluic Acid using Azacrown Ether-tethered Mn(III) Schiff Base Complexes as Catalysts

The oxidation of p-xylene to p-toluic acid with air at 110°C under normal atmospheric pressure occurs efficiently in the presence of crown Mn(III) Schiff base complexes [Formula: See Text] (n=1-4). Significant conversion levels (up to 75%) and selectivity (up to 92-96%) are obtained; the effect of the azacrown ether pendants in Mn(III) Schiff base complexes on the oxidation of p-xylene are also investigated by comparison with the crown-free analogues [Formula: See Text] Moreover, addition of alkali metal ions accelerates the rate of conversion of p-xylene to p-toluic acid.     

Crystal structure of the copper complex of the Schiff base from 1-(N,N-dimethylaminomethyl)-2-formylcymantrene and (S)-alanyl-(S)-alanine

The mechanism of stereoselective syntheses of amino acids via glycine Schiff base/metal complexes is discussed on the basis of data from the X-ray structure determination of (OC)₃Mn[η⁵-C₅H₃(CH₂NMe₂)(CHNCHMeC(O)N---CHMeCOO)Cu]. The absolute configuration of the latter complex is S (the Mn and Cu atoms are trans with respect to the Cp plane).     

A Porphyrin‐Based Porous rtl Metal–Organic Framework as an Efficient Catalyst for the Cycloaddition of CO2 to Epoxides

A porous rtl metal–organic framework (MOF) [Mn₅L(H₂O)₆?(DMA)₂]?5DMA?4C₂H₅OH ( 1? Mn) (H₁₀L=5,10,15,20‐tetra(4‐(3,5‐dicarboxylphenoxy)phenyl)porphyrin; DMA=N,N′‐dimethylacetamide) was synthesized by employing a new porphyrin‐based octacarboxylic acid ligand. 1? Mn exhibits high Mn^II density in the porous framework, providing it great Lewis‐acid heterogeneous catalytic capability for the cycloaddition of CO₂ with epoxides. Strikingly, 1? Mn features excellent catalytic activity to the cycloaddition of CO₂ to epoxides, with a remarkable initial turnover frequency 400 per mole of catalyst per hour at 20 atm. As‐synthesized 1? Mn also exhibits size selectivity to different epoxide substrates on account of their steric hindrance. The high catalytic activity, size selectivity, and stability toward the epoxides on catalytic cycloaddition of CO₂ make 1? Mn a promising heterogeneous catalyst for fixation and utilization of CO₂.     

Synthesis,crystal structure and magnetic properties of [Mn(LH)2(H2O)2] n with a two-dimensional layered structure and three-dimensional hydrogen bonding network

A new manganese polymer [Mn(LH)₂(H₂O)₂] _n (LH₂ = iminodiacetic acid) (1) has been prepared and structurally and magnetically characterized. The polymer has a two-dimensional (2D) layered structure with the unique Mn atom on an inversion center, surrounded by six oxygen atoms. In each layer, all iminodiacetic acid entities are coordinated to Mn atoms in a bridging/bidentate mode, thus linking the [Mn(LH)₂(H₂O)₂] monomeric units together to form a 2D layered polymer. Hydrogen bonding is responsible for an extended three-dimensional network. Analysis of variable-temperature magnetic susceptibility data (2–300) K shows that the polymer displays weak antiferromagnetic exchange interaction with a coupling constant, J = –0.28 cm^–1.