原位固相接枝改性碳酸钙/聚丙烯复合材料的制备

用马来酸酐（MAH）在碳酸钙（CaCO3）表面引入双键,通过原位固相接枝法将聚丙烯蜡（PPW）化学键合在CaCO3表面,制得3种接枝率的CaCO3-MAH-PPW。 将这3种改性CaCO3填充聚丙烯（PP）制备复合材料,研究了PP/CaCO3界面作用对复合材料强度的影响。 结果表明,CaCO3表面经PPW接枝改性后在PP中的分散性提高,与PP相容性变好;随着改性CaCO3表面PPW接枝率的提高,CaCO3与PP之间界面作用逐渐增强。 当PPW接枝率为4.48 mg PPW/g CaCO3时,CaCO3与PP之间的界面作用最强,复合材料拉伸强度下降最小,杨氏模量提升最大,当m(PP)∶m(CaCO3)=100∶50时,杨氏模量达0.86 GPa,是纯PP的1.63倍;而PPW化学接枝率为2.49 mg PPW/g CaCO3时,CaCO3与PP之间的界面作用适中,复合材料缺口冲击强度提升最大,且当m(PP)∶m(CaCO3)=100∶10时,缺口冲击强度达3.91 kJ/m2,是纯PP的1.35倍。     

磨盘碾磨制备PA6/PP/SBS共混物的结构与性能

采用磨盘形力化学反应器,在室温下制备了PA6/PP超细混合粉体,与SBS共混制得PA6/PP/SBS共混物,测定了材料的力学性能并用TEM研究了材料在不同加工温度下相结构的变化.结果表明,通过固相力化学粉碎制备的PA6/PP混合微粉,改善了PA6与PP和SBS的相容性,促进了PA6及PP的分散和与SBS的相界面结合.在微粉填充量为4%～8%(质量分数)时,材料的拉伸强度大幅度提高,扯断伸长率保持不变.加工温度变化引起材料相结构的变化对材料性能产生显著影响.在PP熔融温度下加工,PP粒子产生粘连形成链状结构,可提高材料的力学性能.     

亚微米级四方相钛酸钡低温固相法制备及晶型控制

以八水合氢氧化钡和α-钛酸为原料,在相对低的焙烧温度下,制备出近似球形、亚微米级的钛酸钡。通过XRD、SEM、Raman和FTIR等手段对钛酸钡样品进行表征,样品具有高结晶度,颗粒均一性良好。晶型转变的初步探究表明,立方相为主的钛酸钡可以在400℃发生晶相转变,成为以四方相为主的钛酸钡。     

双单体固相共聚改性聚丙烯技术及其机理研究

在马来酸酐(MAH)固相接枝改性聚丙烯(PP)的过程中加入合适比例的异氰脲酸三烯丙酯(TAIC)作为共聚单体,可以大大提高MAH在PP上的接枝率,同时可以有效抑制在普通固相接枝过程中PP的严重降解,得到了性能较好的高极性PP.与普通固相接枝法与熔体接枝法对比,双单体固相共聚接枝改性PP是一种得到高极性PP的有效方法.本文同时对双单体在固相接枝反应中的作用机理进行了探讨.     

固相力化学改性高聚物的方法研究

在固相应力作用下高聚物分子结构可被削弱或破坏,化学键可能发生畸变或断裂。固相力化学改性高聚物是研究各种高聚物因机械力影响而发生化学或物理化学变化的方法。由于该方法具有适用性广、产品纯净、操作方便、效率高、简便、节能、无污染等优点而成为高聚物改性的重要方法之一。本文系统综述了高聚物的固相剪切粉碎、固相磨盘型碾磨粉碎、高能...     

固相力化学方法回收利用废弃聚丙烯/废旧电路板的研究

采用固相力化学技术制备废旧电路板非金属材料(WPCB)改性粉体,填充废弃聚丙烯(PP),制备了高性能废旧PP/WPCB复合材料,研究了固相剪切对WPCB粒度、粒度分布以及PP/WPCB复合材料结构、流变性能和力学性能的影响。结果表明,磨盘碾磨使WPCB粉体体积粒径由282.4μm降到63.5μm,比表面积由0.06m2/g提高到0.14m2/g,粒度分布明显变窄,玻纤与环氧树脂剥离效果明显。固相力化学方法制备WPCB粉体填充废旧PP后,其分散大幅改善,加工性能明显优于未碾磨体系,复合材料力学性能优于纯PP和未经固相力化学处理的PP/WPCB复合材料,相对于纯PP拉伸强度提高14.6%,弯曲模量提高82.5%,缺口冲击强度提高11.2%。得到的材料表面色泽均一、成本低廉,具有良好工业化前景。     

固相萃取-气相色谱/串联质谱法测定废棉中18种邻苯二甲酸酯类增塑剂

建立了固相萃取-气相色谱/串联质谱(SPE-GC/MS)对废棉中18种邻苯二甲酸酯类增塑剂的分析方法.样品用乙酸乙酯-正己烷提取,HC-C18固相萃取柱富集与净化,经HP-5MS毛细管色谱柱分离,选择离子扫描(SIM)模式,外标法定量.18种增塑剂在0.1～10μg/mL(DIHP,DINP,DIDP为0.5～50μg...     

固相萃取/液相色谱-串联质谱法测定麦卢卡蜂蜜特征化合物

建立了固相萃取/液相色谱-串联质谱(SPE/LC-MS/MS)同时测定麦卢卡蜂蜜中4种特征化合物2'-甲氧基苯乙酮(2'-MAP)、2-甲氧基苯甲酸(2-MBA)、3-苯基乳酸(3-PA)和4-羟基苯基乳酸(4-HPA)的方法。蜂蜜样品用含1%甲酸水溶液溶解,经HLB固相萃取柱净化,Thermo Hypersil Gold C18(50 mm×2.1 mm,1.9μm)色谱柱分离,0.1%甲酸水溶液和0.1%甲酸乙腈为流动相进行梯度洗脱。4种化合物在电喷雾正/负离子多重反应监测模式(MRM)下同时进行检测,外标法定量。结果表明,2'-MAP、2-MBA和4-HPA在0.01~1.0 mg/L、3-PA在0.1~10.0 mg/L范围内线性关系良好,相关系数(r2)均大于0.99。方法检出限(LODs)和定量下限(LOQs)分别为0.1~1.0 mg/kg和0.5~5.0 mg/kg。蜂蜜样品的平均加标回收率为79.4%~98.3%,相对标准偏差(n=6)为3.2%~8.7%。利用该方法对采集于新西兰不同产地的12个品种的114个巢蜜样本和4个国家的50个商品化蜂蜜进行了验证。该法灵敏度和准确度高,分析速度快,可为判别单花种、多花种及非麦卢卡蜂蜜提供参考。     

分散固相萃取净化/液相色谱-串联质谱法测定化妆品中7种氨基苯甲醚

建立了同时测定化妆品中7种氨基苯甲醚类化合物(邻氨基苯甲醚、间氨基苯甲醚、对氨基苯甲醚、2,4-二氨基苯甲醚、2,5-二氨基苯甲醚、3,4-二氨基苯甲醚、3,3'-二甲氧基联苯胺)的分散固相萃取净化液相色谱-串联质谱(LC-MS/MS)分析方法。样品用甲醇-水(1∶1,含0.1%甲酸)溶液提取,经PSA分散固相萃取净化后,样液经Welch Ultimats XB-C_(18)(4.6 mm×150 mm,5μm)色谱柱分离,多反应监测(MRM)模式检测,以保留时间和特征离子对定性,外标法定量。结果表明,7种氨基苯甲醚类化合物在0.10~200.0μg/L浓度范围内线性关系良好,相关系数均大于0.998;方法检出限(S/N=3)为0.4~10.9μg/kg。样品日内回收率为64.7%~98.1%,相对标准偏差(RSD,n=6)为1.2%~10.6%;日间精密度(n=5)为2.3%~9.8%。对30个不同水剂类化妆品检测发现,其中1个样品检出3,3'-二甲氧基联苯胺,含量为5.3μg/kg。该方法准确可靠,适用于化妆品中7种氨基苯甲醚的同时测定。     

SnO2 /MWCNTs纳米复合材料的低热固相制备及其超电容特性研究

采用十二烷基三甲基溴化铵(DTAB)辅助固相法制备SnO2/MWCNTs纳米复合材料,X射线衍射(XRD)、透射电镜(TEM)测试表明,SnO2纳米颗粒均匀包裹在MWCNTs表面.循环伏安和恒流充放电测试表明,与SnO2颗粒和纯MWCNTs相比,SnO2/MWCNTs纳米复合材料在1.0 mol·L-1 Na2SO4电解液中的电化学电容性质得到明显改善.当SnO2质量分数为11%时,在电流密度0.2 A·g-1下,SnO2的电容值最大可达217.3 F·g-1.     

WS2 超细粉体的固相法合成

WS2 超细粉体的固相法合成;WS2;固相反应;过硫系数;高能球磨;粒度     

Effect of CaCO3 Filler Component on Solid State Decomposition Kinetic of PP/LDPE/CaCO3 Composites

In this study, the effect of addition Calcium carbonate (CaCO₃) filler component on solid state thermal decomposition procedures of Polypropylene-Low Density Polyethylene (PP-LDPE; 90/10 wt%) blends involving different amounts (5, 10, 20 wt%) Calcium carbonate (CaCO₃) was investigated using thermogravimetry in dynamic nitrogen atmosphere at different heating rates. An integral composite procedure involving the integral iso-conversional methods such as the Tang (TM), the Kissinger-Akahira-Sunose method (KAS), the Flynn-Wall-Ozawa (FWO), an integral method such as Coats-Redfern (CR) and master plots method were employed to determine the kinetic model and kinetic parameters of the decomposition processes under non-isothermal conditions. The Iso-conversional methods indicated that the thermal decomposition reaction should conform to single reaction model. The results of the integral composite procedures of TG data at various heating rates suggested that thermal processes of PP-LDPE-CaCO₃ composites involving different amounts of CaCO₃ filler component (5, 10, 20 wt%) followed a single step with approximate activation energies of 226.7, 248.9, and 252.0 kJ.mol^{? 1} according to the FWO method, respectively and those of 231.3, 240.1 and 243.0 kJ mol^{? 1} at 5°C min^{? 1} according to the Coats-Redfern method, the reaction mechanisms of all the composites was described from the master plots methods and are P_n model for composite C-1, R_n model for composites C-2 and C-3, respectively. It was found that the thermal stability, activation energy and thermal decomposition process changed by the increasing CaCO₃ filler weight in composite structure.     

Structure and properties of poly(ethylene terephthalate)/Na+‐montmorillonite nanocomposites prepared by solid state shear milling (S3M) method

This article reported a novel technology, solid state shear milling (S³M), to prepare poly(ethylene terephthalate)/Na⁺‐montmorillonite nanocomposites using the pristine Na⁺‐MMT without organic modification so as to avoid the problem that the organic modifiers, used for MMT treatment will decompose at high processing temperature of PET, and the structure and properties of the obtained samples were investigated. XRD and TEM analyses showed that Na⁺‐MMT layers were partially delaminated and intercalated, and uniformly dispersed in the PET matrix when suffering from the strong three dimensional shearing forces of pan‐milling. DSC analysis showed that Na⁺‐MMT serves as a nucleating agent, increasing the crystallization rate as well as the crystallization temperature of PET. The properties such as thermal stability and tensile strength of the PET/Na⁺‐MMT nanocomposites prepared by S³M got remarkably improved. Solid state shear milling (S³M) method was a simple and efficient method to get polymer/Na⁺‐MMT nanocomposites with pretty good performances without organic modification of pristine Na⁺‐MMT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 807–817, 2008     

固相反应法合成Pt/MoO_3及其电催化作用

采用固相合成的方法制得直接甲醇燃料电池催化甲醇氧化的Pt/MoO3.XRD分析、循环伏安测试表明,Pt/MoO3对甲醇的氧化具有较好的催化作用,氧化峰电位出现在0.63V(vs.SCE),峰电流密度可达78.1mA·cm-2.     

Dielectric Properties of Colossal-Dielectric-Constant Na1/2La1/2Cu3Ti4O12 Ceramics Prepared by Spark Plasma Sintering

In the current study, we report on the dielectric behavior of colossal-dielectric-constant Na_1/2La_1/2Cu₃Ti₄O₁₂ (NLCTO) ceramics prepared by mechanochemical synthesis and spark plasma sintering (SPS) at 850 °C, 900 °C, and 925 °C for 10 min. X-ray powder diffraction analysis showed that all the ceramics have a cubic phase. Scanning electron microscope observations revealed an increase in the average grain size from 175 to 300 nm with an increase in the sintering temperature. SPS NLCTO ceramics showed a room-temperature colossal dielectric constant (>10³) and a comparatively high dielectric loss (>0.1) over most of the studied frequency range (1 Hz–40 MHz). Two relaxation peaks were observed in the spectra of the electrical modulus and attributed to the response of grain and grain boundary. According to the Nyquist plots of complex impedance, the SPS NLCTO ceramics have semiconductor grains surrounded by electrically resistive grain boundaries. The colossal dielectric constant of SPS NLCTO ceramics was attributed to the internal barrier layer capacitance (IBLC) effect. The high dielectric loss is thought to be due to the low resistivity of the grain boundary of SPS NLCTO.     

Polyamide‐6/natural clay mineral nanocomposites prepared by solid‐state shear milling using pan‐mill equipment

The polyamide‐6 (PA6)/natural clay mineral nanocomposites were successfully prepared by solid‐state shear milling method without any treatment of clay mineral and additives. PA6/clay mixture was pan‐milled to produce PA6/clay compounding powder, using pan‐mill equipment. The obtained powder as master batch was diluted with neat PA6 to prepare composites by a twin‐screw extruder. The clay silicate layers were found to be partially exfoliated and dispersed homogeneously at nanometer level in PA6 matrix. The rheological measurements and mechanical properties of nanocomposites were characterized. The shear viscosities of nanocomposites were higher than that of pure PA6, and tensile strength and tensile modulus increased, but Izod impact strength decreased, with increasing concentration of clay. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 249–255, 2006     

固体反应法制备纳米LaCo_yMn_(1-y)O_3系复合氧化物及其表征

采用研磨固相反应法制备 La Coy Mn1 - y O3钙钛矿型复合氧化物纳米微粒 .利用 XRD、TG-DTA、TEM技术研究了 La Coy Mn1 - y O3的形成过程 ,并考察了微粒形貌及其平均粒径 .用交流阻抗法和磁天平测定了样品的电导率和磁化率 ,结果表明 ,当取代量 y=0 .5时 ,其电导与磁化率均最小 ,并初步作了机理探讨 .     

固相萃取/液相色谱-串联质谱法测定油脂中的3-氯-1,2-丙二醇棕榈酸二酯

建立了固相萃取/液相色谱-串联质谱检测油脂中3-氯-1,2-丙二醇棕榈酸二酯(3-MCPD-DP)的分析方法。油脂经溶解后,以自填装PSA+C_(18)吸附剂的固相萃取柱净化,ThermoFisher Accucore C_(18)色谱柱分离,以10 mmol/L甲酸铵甲醇溶液和10 mmol/L甲酸铵异丙醇溶液为流动相梯度洗脱,电喷雾正离子模式扫描,多反应监测模式定性分析,内标法定量。对离子化条件、固相萃取吸附剂用量、洗脱条件、定容溶液等条件进行了考察。在优化条件下,3-MCPD-DP在0.5～1 000 ng/mL范围内线性关系良好(r~20.999),方法检出限(S/N≥3)与定量下限(S/N≥10)分别为0.025 mg/kg和0.050 mg/kg。在橄榄油样品中加标量为0.1～0.5 mg/kg时,3-MCPD-DP的平均回收率为90.8%～102%,相对标准偏差(RSD,n=6)为1.1%～3.0%。该方法前处理简单快速、灵敏度较高,可满足油脂中3-MCPD-DP的检测要求。     

Solid State Synthesis and Structural Characterization of Binuclear Cu(I)-SbPh3 Complex [Cu(SbPh3)2I]2

Dimeric complex [Cu(SbPh3)2I]2 has been synthesized by a solid state reaction at a low heating temperature and its crystal structure has been analyzed by X-ray crystallography. The crystal is monoclinic, space group P21/a (#14), a = 20.436(5), b=14.125(3), c=24.683(3)(A), β=110.67(1)°, Z=4, V=6666(2)(A)3; C72H60Sb4I2Cu2, Mr = 1792, Dc = 1.787 g.cm-3, μ(MoKα) = 31.88 cm-1, F(000)=3440, R=0.038 and Rw=0.043 for 5632 observed reflections (I≥3.0σ(I)) and 361 refined parameters. The result reveals the copper and the bridging iodide atoms form an approximately planar rhomboid array. Effects of the bulkiness of the ligands upon the structures of the analogous complexes are discussed.