Determination of carbaryl by flow injection with luminol chemiluminescence inhibition detection

A flow-injection procedure is described for the determination of carbaryl based on its inhibition effect on luminol-cobalt(II) chemiluminescence reaction in alkaline medium in the presence of hydrogen peroxide. The calibration data over the range 5.0?×?10^?7 to 20?×?10^?6?M give a correlation coefficient (r ²) of 0.9972 with relative standard deviations (RSD; n?=?4) in the range of 1.0–2.1% with a limit of detection (3?×?blank noise) of 2.37?×?10^?7?M for carbaryl. The sample throughput was 120?h^?1. The effects of some carbamates, anions, and cations were studied on luminol CL system for carbaryl determination. The proposed method has been applied to determine carbaryl in natural waters.     

Determination of N-methylcarbamate pesticides in water and vegetable samples by HPLC with post-column chemiluminescence detection using the luminol reaction

In this paper we proposed a reverse high performance liquid chromatography method for the simultaneous determination of three N-methylcarbamates (NMCs) named carbofuran, carbaryl and methiocarb, using the post-column chemiluminescence (CL) detection with the luminol reaction. This method is based on the enhancing effect of these analytes on the CL emission generated by the oxidation of luminol with potassium permanganate in alkaline medium. The separation was reached in less than 14 min using a C18 column and an isocratic binary mobile phase consisting of acetonitrile:water (50:50, v/v) pumped at a flow rate of 1 mL min⁻¹. CL reagents (luminol and KMnO₄) were incorporated by means of a peristaltic pump and were firstly mixed using a three-way connector. Then this stream was mixed with the eluate using another three-way connector just before reaching the detection cell. The optimization of variables affecting the CL reaction (reaction medium, concentration, flow rate of reagents and distance between both connectors) were optimized by means of experimental designs. Ethiofencarb, a NMC which has nowadays fallen into disuse was used as internal standard. For the analysis of theses pesticides in real water samples a pre-treatment step consisting of solid phase extraction (SPE) was conducted in order to reach sensitivity levels below the legal maximum concentration permitted. In the case of vegetable sample, SPE was used for matrix cleaning purpose.     

Determination of photoirradiated high polar benzoylureas in tomato by HPLC with luminol chemiluminescence detection

This study reports the first analytical application of luminol chemiluminescence reaction for the sensitive detection of two benzoylurea insecticides (diflubenzuron and triflumuron). Off-line experiments demonstrated that previously irradiated traces of these benzoylurea insecticides largely enhanced the chemiluminescence emission yielded from the oxidation of luminol in methanol:water mixtures, by potassium permanganate in alkaline medium, the enhancement being proportional to the concentration of both pesticides. The two benzoylureas were determined in tomato samples by coupling liquid chromatography with post-column photoderivatization and detection based on this chemiluminescence reaction. Tomato samples were extracted using the QuEChERS method based on extraction with acetonitrile and dispersive solid-phase clean-up using primary and secondary amine (PSA). Interferences due to matrix effect were overcome by using matrix-matched standards. The optimised method was validated with respect to linearity, limits of detection and quantification, precision and accuracy. Under the optimised conditions, calibrations graphs were linear between 0.05 and 0.50 μg mL⁻¹ for diflubenzuron and between 0.10 and 1.00 μg mL⁻¹ for triflumuron. Method detection limits were 0.0025 and 0.0131 μg mL⁻¹ (equivalent to 0.0005 and 0.0026 mg kg⁻¹) and quantification limits were 0.05 and 0.10 μg mL⁻¹ (equivalent to 0.01 and 0.02 mg kg⁻¹) for diflubenzuron and triflumuron, respectively. In both cases, quantification limits were lower than the maximum residue levels (MRLs) established by the European legislation. The relative standard deviation of intra-day precision was below 10% and recoveries were between 79.7% and 94.2% for both pesticides.     

Determination of nanomolar concentrations of phosphate in freshwaters using flow injection with luminol chemiluminescence detection

A simple and rapid flow injection (FI) method is reported for the determination of phosphate (as molybdate reactive P) in freshwaters based on luminol chemiluminescence (CL) detection. The molybdophosphoric heteropoly acid formed by phosphate and ammonium molybdate in acidic conditions generated chemiluminescence emission via the oxidation of luminol. The detection limit (3× standard deviation of blank) was 0.03 μg P l⁻¹ (1.0 nM), with a sample throughput of 180 h⁻¹. The calibration graph was linear over the range 0.032–3.26 μg P l⁻¹ (r²=0.9880) with relative standard deviations (n=4) in the range 1.2–4.7%. Interfering cations (Ca(II), Mg(II), Ni(II), Zn(II), Cu(II), Co(II), Fe(II) and Fe(III)) were removed by passing the sample through an in-line iminodiacetate chelating column. Silicate interference (at 5 mg Si l⁻¹) was effectively masked by the addition of tartaric acid and other common anions (Cl⁻, SO₄²⁻, HCO₃⁻, NO₃⁻ and NO₂⁻) did not interfere at their maximum admissible concentrations in freshwaters. The method was applied to freshwater samples and the results (26.1±1.1–62.0±0.4 μg P l⁻¹) were not significantly different (P=0.05) from results obtained using a segmented flow analyser method with spectrophotometric detection (24.4±4.45–84.0±16.0 μg P l⁻¹).     

Mg-Al-carbonate layered double hydroxides as a novel catalyst of luminol chemiluminescence

The interlayer carbonate in Mg-Al layered double hydroxides as a novel catalyst of luminol chemiluminescence has been reported for the first time, which has great potential in further applications of luminol chemiluminescence for sensitive sensors, catalyst-conjugated probes.     

A rapid spectrophotometric assay of some organophosphorus pesticide residues in vegetable samples

A rapid and sensitive spectrophotometric method for the determination of some organophosphorus insecticides, i.e. malathion, dimethoate and phorate is described. It is based on the oxidation of organophosphorus pesticide with slight excess of N-bromosuccinimide (NBS) and the unconsumed NBS is determined with rhodamine B (lambda max: 550 nm). Beer's law is obeyed in the concentration range 0.108-1.08, 0.056-0.56 and 0.028-0.28 microg mL(-1) for malathion, phorate and dimethoate, respectively. The method has been successfully applied for the determination of organophosphorus pesticide residues in various vegetable samples.     

Photodegradation and flow-injection determination of simetryn herbicide by luminol chemiluminescence detection

A novel and simple flow injection chemiluminescence method is reported for the determination of simetryn, a common herbicide. The method is based on the direct oxidation of luminol by the photoproducts of the simetryn in alkaline medium in the absence of catalyst/oxidant. The linear concentration range was 0.01 - 2 microg mL(-1) simetryn with a correlation coefficient (r(2)) of 0.9997 and relative standard deviations (RSD; n = 4) in the range of 0.9 - 2.3%. The limit of detection (S/N = 3) was 7.5 ng mL(-1) with a sample throughput of 100 h(-1). The proposed method has been applied to determine simetryn in natural waters using Sep-Pak C(18) cartridges for solid phase extraction (SPE) procedure. The recoveries were in the range of 97 +/- 1 to 104 +/- 2%. The mechanism of chemiluminescence reaction has also been discussed briefly.     

Determination of arsenic(V) in freshwaters by flow injection with luminol chemiluminescence detection

A simple and rapid flow injection (FI) method is reported for the determination of arsenic(V) based on luminol chemiluminescence (CL) detection. The molybdoarsenic heteropoly acid formed by arsenic and ammonium molybdate in the presence of ammonium vanadate in acidic conditions generated chemiluminescence emission via the oxidation of luminol. The limit of detection was 0.15 μg L^?1, with a sample throughput 120 h^?1. A linear calibration graph was obtained over the range 0.15 to 7.5 μg L^?1 (r ² = 0.9989; n = 9) with relative standard deviation (n = 4) in the range 0.8 to 2.5%. Interfering cations were removed by passing the sample through an in-line iminodiacetate chelating column and phosphate (at 0.6 mg L^?1) was removed off-line by magnesium-induced coprecipitation (MAGIC) method. The method was applied to freshwater samples and the results obtained were in reasonable agreement with the results obtained using HGAAS as the reference method.     

Flow injection analysis of ultratrace orthophosphate in seawater with solid-phase enrichment and luminol chemiluminescence detection

Solid-phase extraction technique had been applied to extract molybdophosphoric heteropoly acid (MoP) paired with cetyltrimethylammonium bromide (CTAB) from seawater matrix using C18 sorbent. Chemiluminescence emission could be generated via MoP reaction with alkaline luminol. Based on these, a novel on-line solid-phase extraction method coupled with flow injection (FI) analysis and luminol chemiluminescence detection had been established to determine ultratrace orthophosphate in seawater. The MoP-CTAB compound could be efficiently extracted on an in-line Sep-Pak C18 cartridge, and rapidly eluted by 0.3 mol l⁻¹ sulphuric acid-ethanol solution. Then the compound was reduced by luminol to produce chemiluminescence light, which could be detected using a luminescence analyzer. Experimental parameters were optimized using a univariate experimental design. Using artificial seawater with salinity of 35 as a matrix, the standard curve with a linear range between 0.005 and 0.194 μmol l⁻¹ had been obtained, and the recovery and the detection limit of the proposed method were found to be 92.5% and 0.002 μmol l⁻¹, respectively. The relative standard deviation (R.S.D.), which was determined over eight hour, was 4.66% (n = 7) for the artificial seawater at a concentration of 0.097 μmol l⁻¹ orthophosphate. Si of 200 μmol l⁻¹ would not interfere with the detection of 0.012 μmol l⁻¹ orthophosphate compound. Three typical seawater samples were analyzed using both the proposed method and the magnesium hydroxide-induced coprecipitation (MAGIC) method, and the results of the two methods showed no significant difference using the t test. Compared to the MAGIC method, the proposed method was more sensitive, time saving and easy for on-line analysis.     

鲁米诺-铁氰化钾化学发光体系测定左旋多巴

铁氰化钾在碱性条件能氧化鲁米诺而发光,左旋多巴能大大增强该发光强度。基于此现象并结合流动注射技术,建立起一种直接测定左旋多巴的流动注射化学发光分析法。方法检出限为1.2×10-10g mL,左旋多巴质量浓度在5 0×10-10～5.0×10-8g mL范围内与发光强度呈良好的线性关系。相对标准偏差为2.9%(左旋多巴5.0×10-9g mL,n=11)。该方法可用于片剂中左旋多巴量的测定。     

A novel immunochromatographic assay based on a time-resolved chemiluminescence strategy for the multiplexed detection of ractopamine and clenbuterol

A novel multiplexed immunochromatographic assay (ICA) based on a time-resolved chemiluminescence (CL) strategy was developed for quantitative detection of β-agonists, by utilizing ractopamine (RAC) and clenbuterol (CLE) as the models. Different from conventional multiplexed ICA methods which usually require two or more test lines, this strategy was developed for detection of two β-agonists by using only one test line on the nitrocellulose membrane. In this study, horseradish peroxidase and alkaline phosphatase were used as the signal probes to label RAC antibody and CLE antibody, respectively. The two CL reactions with flash type and glow type kinetics characteristics were triggered simultaneously by injecting the coreactants, then the signals for RAC and CLE detections were recorded at 3 s and 300 s after coreactants injection, respectively. Owing to the utilization of CL detection, this protocol showed ideal sensitivity for quantitation. Under the optimal conditions, the detection limits for RAC and CLE were 0.17 ng mL⁻¹ and 0.067 ng mL⁻¹ (S/N = 3), respectively. The whole assay process can be accomplished within 20 min without complicated sample pretreatment. The proposed method was successfully applied for the detection of RAC and CLE in spiked swine urine. It opens up a new pathway for designing a low cost, time-efficiency and multiplexed strategy for rapid screening and field assay.     

A study of the chemiluminescence behavior of myoglobin with luminol and its analytical applications

A chemiluminescence signal at 425 nm was observed when ferric state myoglobin was mixed with luminol in alkaline medium. Because the signal was remarkably enhanced in the presence of Fe(CN)₆ ^4–, analytical applications were investigated in a flow-injection system. The increase in chemiluminescence was linearly dependent on myoglobin concentration in the range 0.1 to 100 nmol L^–1, and the limit of detection was 0.04 nmol L^–1 with relative standard deviation 3.2% (3). It was also found that binding of Mb with the ligands CN^–, SCN^–, and F^– significantly inhibited the chemiluminescence reaction. The linear dynamic ranges for the ligands were 1.0–300.0, 0.1–3.0, and 0.5–100.0 nmol L^–1, and the limits of detection (S/N=3) 0.4, 0.04, and 0.2 nmol L^–1, for F^–, CN^–, and SCN^–, respectively. The relative standard deviations were 5.32%, 6.13%, and 3.38% for 0.1 nmol L^–1 CN^–, 0.5 nmol L^–1 SCN^–, and 1.0 nmol L^–1 F^–, respectively. At a flow rate of 2.0 mL min^–1 the assay could be accomplished in 1 min, including sampling and washing. The method has been successfully applied to the determination of myoglobin in human urine and F^– in water samples. A possible mechanism of chemiluminescence production by myoglobin and luminol is presented.     

鲁米诺-铁氰化钾化学发光体系测定双嘧达莫

在碱性条件下,铁氰化钾氧化鲁米诺产生化学发光,双嘧达莫对该体系的化学发光有显著的增强作用。基于此并结合流动注射技术建立了测定双嘧达莫的新方法。该方法检出限为5.7×10-11g mL(IUPAC),线性范围为1.0×10-10～5.0×10-8g mL,对5.0×10-9g mL双嘧达莫平行测定11次,其相对标准偏差为1.9%。     

A novel fluorescent epoxy resin for organophosphate pesticide detection

In this work,a novel bisbenzimidazolylpyridine-functionalized fluorescent epoxy resin was synthesized for organophosphate pesticide detection.The epoxy resin was characterized by Fourier-transform infrared spectroscopy(FT-IR),proton nuclear magnetic resonance spectroscopy(~1H NMR),gel permeation chromatography(CPC),differential scanning calorimetry(DSC) and fluorescence spectroscopy.After loading with Eu(Ⅲ) ions,the epoxy resin showed a strong fluorescence emission.The fluorescence emission was observed to be instantaneously quenched when exposed to trace amount of diethyl chlorophosphate in solution.The Stern-Volmer quenching constants K_(sv) for quenching at617 nm was determined to be 0.377 × 10~3 L/mol.This sensitive emission-quenching function and easy processing nature of the polymeric support enable the resin to be a promising chemosensor candidate for the detection of organophosphates.     

Enzymatic assay with detection by enhanced luminol chemiluminescence in a reversed micellar system: determination of l-amino acids and glucose

A detection system for hydrogen peroxide, i.e., luminol chemiluminescence (CL) in a hexadecyltrimethylammonium bromide (CTAB) reversed micellar system, was coupled to enzyme reactions. The use of CTAB reversed micellar medium allows one to conduct both the oxidase enzymatic and CL detection reactions simultaneously at mild pH (l-amino acid system, pH 8.7; glucose system, pH 8.5) in the absence of any co-oxidant or catalyst. Based on this result, simple and unique determinations of l-amino acids and glucose as substrates were developed. The calibration graph for a representative amino acid, l-phenylalanine, was linear in the concentration range 4.0×10^?6?200×10^?6M with a relative standard deviation of 5.78% (five determinations). The method established for l-phenylalanine was also applicable for the assay of fourteen other l-amino acids. The calibration graph for glucose was linear in the concentration range 5.4×10^??540×10^?6M with a relative standard deviation of 4.27% (eight determinations). This method was compared with a standard spectrophotometric method (hexokinase) and successfully applied to the determination of glucose in human serum.     

Surface molecular imprinting for chemiluminescence detection of the organophosphate pesticide chlorpyrifos

We report on a surface molecular imprinting strategy for synthesizing core-shell particles whose shell is imprinted with chlorpyrifos (CPF). The particles were prepared by copolymerization of the methacryloyl groups on the surface of silica particles modified with 3-methacryloxypropyl trimethoxysilane a functional monomer and a cross-linking agent. The imprinted particles exhibit larger binding capacity, faster binding kinetics, and higher recognition selectivity for CPF. Combined with highly sensitive chemiluminescence assay, the method was applied to the determination of CPF with a detection limit of 0.92?nM which is about 2 orders of magnitude lower than that by conventional CL method. The method also displays repeatability for more than 200 times.

Determination of phenols by flow injection and liquid chromatography with on-line quinine-sensitized photo-oxidation and quenched luminol chemiluminescence detection

An on-line quinine-sensitized photo-oxidation with quenched chemiluminescence (CL) detection method is developed for phenols using flow injection (FI) and liquid chromatography (LC). This detection method is based on the decrease of light emission from the luminol CL reaction due to the photo-oxidation of phenols that scavenge the photogenerated reactive oxygen species (e.g. singlet oxygen () and superoxide (O₂⁻)). On-line photo-oxidation is achieved using a coil photo-reactor made from fluoroethylene-propylene copolymer tubing ( mm i.d.) coiled around a mercury UV lamp. A buffer of pH 7 and a concentration of 350 μM for quinine sulfate are determined optimum for the sensitized photo-oxidation. Using a carrier system flow rate of 60 μl/min, calibration curves taken by FI for 10 phenolic compounds in aqueous solutions showed this decreasing sensitivity order: 4-chlorophenol, phenol, 4-nitrophenol, 3-hydroxy-l-kynurenine, 2-nitrophenol, salicylate, 3-nitrophenol, catechol, 2,4-dinitrophenol, and 2,4-dichlorophenol. This detection method using two tandem coil photo-reactors is also applied for the LC separation of phenol, 4-nitrophenol and 4-chlorophenol on an octadecyl (C18) silica LC column using acetonitrile-H₂O (40:60, v/v) as a mobile phase. The quenched CL detection limits (about 1 μM or 20 pmol) for phenol and 4-chlorophenol are comparable to those for UV detection at 254 nm. Some selectivity in the quenched CL detection is evident by no interference in the FI phenol response even when benzaldehyde and phenethanol concentrations are 8 and 15 times that of phenol.     

Sensitive determination of captopril by flow injection analysis with chemiluminescence detection based on the enhancement of the luminol reaction

This work reports a novel flow injection (FI) method for the determination of captopril, 1-[(2S)-3-mercapto-2-methylpropionyl]-l-proline (CPL), based on the enhancement CPL affords on the chemiluminescence (CL) reaction between luminol and hydrogen peroxide. For this purpose alkaline luminol and hydrogen peroxide solutions were mixed online, the sample containing CPL was injected into an aqueous carrier stream, mixed with the luminol-hydrogen peroxide stream and pumped into a glass flow cell positioned in front of a photomultiplier tube (PMT). The increase in the CL intensity was recorded in the form of FI peaks, the height of which was related to the CPL mass concentration in the sample. Different chemical and instrumental parameters affecting the CL response were investigated. Under the selected conditions, the log-log calibration curve was linear in the range 5-5000 μg l⁻¹ of CPL, the limit of detection was 2 μg l⁻¹ (at the 3σ level), the R.S.D., s_r was 3.1% at the 100 μg l⁻¹ level (n=8) and the sampling rate was 180 injections h⁻¹. The method was applied to the determination of CPL in pharmaceutical formulations with recoveries in the range 100±3%.     

Determination of ATP via the photochemical generation of hydrogen peroxide using flow injection luminol chemiluminescence detection

The determination of ATP using the coupling between a photochemical reaction and a chemiluminescence reaction in a flow injection (FI) system is described. The method is based on the reaction of glucose with ATP catalyzed by hexokinase and Mg²⁺ ions. The glucose that is not consumed by ATP is subsequently photooxidized using 9,10-anthraquinone-2,6-disulfonate as a sensitizer. The hydrogen peroxide produced in the photochemical reaction is monitored through the chemiluminescence reaction with luminol catalyzed by hematine. There is a linear relationship between the decrease in the chemiluminescence response and the ATP concentration at a constant concentration of glucose. Under the optimum conditions, the calibration graph is linear in the range 0.20–50.5 mg L^–1 with a throughput of 25 samples per hour and relative standard deviations between ±0.62 and ±1.42%. The limit of detection is 0.07 mg L^–1. The method was used for the determination of ATP in pharmaceuticals, milk, and soils.