共查询到15条相似文献,搜索用时 109 毫秒
1.
针对脉冲激光引信应用于中小口径常规弹药过程,由于体积严格受限而造成引信内部电磁干扰严重的问题,结合发射、接收模块工作原理,说明在其内部采取电磁干扰抑制措施的必要性。通过分析发射、接收模块电磁干扰产生机理,提出采用双重屏蔽方法抑制辐射干扰,采用线性阻抗稳定网络、缓冲网络和共差模合成扼流圈结合的多重滤波技术抑制传导干扰。对各措施作用效果进行仿真与实验,结果表明:厚度为1.55 mm钢材料对辐射干扰具有良好屏蔽效果;接收模块输出干扰信号峰峰值减小至70 mV,约为原干扰信号的1/40。这些方法大幅度降低了脉冲激光引信内部的电磁干扰,且工作稳定可靠。 相似文献
2.
3.
4.
5.
6.
激光引信接收光学组件的研究与测试 总被引:1,自引:0,他引:1
根据大气激光通信传输方程和黑体辐射理论提出了计算激光引信中接收光学系统接收视场的方法,通过接收视场确定了接收光学系统的初始结构参数,设计了焦距为15 mm,视场角为2ω≮±7°的柱透镜光学系统.采用倒置法,将线阵CCD探测器置于准直物镜的焦面上接收信号,解决了接收光学系统后截距过短无法安置线阵CCD的问题,扩大了测量范围,又保证了精度,测量误差为1%.针对激光引信的结构特点,设计了测量激光引信接收光学系统视场角的自动测试系统.实验测试结果表明该引信的视场角都在合格范围内,重复精度≤5%,满足设计的要求. 相似文献
7.
基于LabVIEW激光引信回波模拟装置设计 总被引:4,自引:1,他引:3
激光引信回波模拟装置是激光引信测试设备的重要组成部分。介绍了激光引信回波模拟装置的组成,设计了用于该装置的硬件电路和软件控制系统。硬件电路采用单片机完成控制指令的接收和控制信号的产生,使用串行扩展芯片GM8125将单片机AT89S52的串行口扩展成5个,满足了激光引信回波模拟装置串口资源要求。软件控制系统基于LabVlFⅣ设计,主要包括串口通信程序和控制指令的产生程序,控制指令经串口通信传送给硬件电路。实验结果表明,该装置满足激光引信测试设备的要求。 相似文献
8.
9.
根据大气激光通信传输方程和黑体辐射理论提出了计算激光引信中接收光学系统接收视场的方法,通过接收视场确定了接收光学系统的初始结构参数,设计了焦距为15 mm,视场角为2ω≮±7°的柱透镜光学系统.采用倒置法,将线阵CCD探测器置于准直物镜的焦面上接收信号,解决了接收光学系统后截距过短无法安置线阵CCD的问题,扩大了测量范围,又保证了精度,测量误差为1%.针对激光引信的结构特点,设计了测量激光引信接收光学系统视场角的自动测试系统.实验测试结果表明该引信的视场角都在合格范围内,重复精度≤5%,满足设计的要求. 相似文献
10.
11.
根据定向起爆部对引信提出的时间匹配和空间匹配的要求,针对弹目交会相对运动环境,在惯性坐标系下3个相互垂直的2维平面内,建立了弹目相对速度下脉冲激光方位探测引信系统的最佳起爆延时和最佳起爆方位角模型,并对相关时间匹配和空间匹配特性进行了量化及数值仿真分析。结果表明:模型与弹目交会角、目标初始方位角、发射激光束与弹丸速度夹角、引信中心至目标尾部距离、目标外型参数、目标速度、破片飞散速度、弹丸内部结构参数、弹丸速度等目标区环境信息有关 相似文献
12.
Zhen Zhang 《中国物理 B》2023,32(1):13202-013202
We designed, assembled, and tested a reliable laser system for 87Rb cold atom fountain clocks. The laser system is divided into four modules according to function, which are convenient for installing, adjusting, maintaining, and replacing of the modules. In each functional module, all optical components are fixed on a baseplate with glue and screws, ensuring the system's structural stability. Mechanical stability was verified in a 6.11g RMS randomvibration test, where the change in output power before and after vibration was less than 5%. Thermal stability was realized by optimizing of the structure and appropriate selection of component materials of the modules through thermal simulation. In the laser splitting and output module, the change in laser power was less than 20% for each fiber in thermal cycles from 5 ℃ to 43 ℃. Finally, the functionality of the laser system was verified for a rubidium fountain clock. 相似文献
13.
14.
Measurement of small-signal and large-signal responses of packaged laser modules at high temperature
Ning Hua Zhu Ji Min Wen Hai Peng Song Shang Jian Zhang Liang Xie 《Optical and Quantum Electronics》2006,38(15):1245-1257
In this paper, the pulsed injection method is extended to measure the chip temperature of various packaged laser modules,
such as the DFB laser modules, the FP laser modules, and the EML laser modules. An optimal injection condition is obtained
by investigating the dependence of the lasing wavelength on the width and period of the injection pulse in a relatively wide
temperature range. The small-signal frequency responses and large-signal performances of packaged laser modules at different
chip temperature are measured. The adiabatic small-signal modulation characteristics of packaged LD are first extracted. In
the large-signal measurement, the effects of chip temperature, bias current and driving signal on the performances of the
laser modules are discussed. It has been found that the large-signal performances of the EML modules depend on the different
red-shift speeds of the DFB and EAM sections as chip temperature varying, and the optimal characteristics may be achieved
at higher temperature. 相似文献