A new eccentric-cylinder rheometer

A new eccentric-cylinder rheometer with guard-ring equipment was constructed as an auxiliary set-up to a Rheometrics Mechanical Spectrometer, type 7200, which enables measurements with the eccentric disk technique. Experimental tests with Newtonian fluids and polymer solutions of relatively low viscosity show that this instrument yields reliable plots of shear viscosity and first normal-stress coefficient over several decades of the effective average shear rate. These coincide very well with plots from a commercial cone-and-plate rheometer even for higher relative eccentricities (up to 0.75). However, no systematic effects of eccentricity, to be expected for higher shear rates, could be observed with these fluids, so that supplementary tests applying fluids with more pronounced viscoelastic properties are to be carried out.     

Stability of Couette flow of liquids with power law viscosity

The stability of the Couette flow of the liquid with the power law viscosity in a wide annular gap has been investigated theoretically in this work with the aid of the method of small disturbances. The Taylor number, being a criterion of the stability, has been defined using the mean apparent viscosity value in the main flow. In the whole range of the radius ratio, R _i /R _o and the flow index, n, considered (R _i /R _o 0.5, n = 0.25–1.75 ), the critical value of the Taylor number Ta _c is an increasing function of the flow index, i.e., shear thinning has destabilizing influence on the rotational flow, and dilatancy exhibits an opposite tendency.In the wide ranges of the flow index, n > 0.5, and the radius ratio, R _i /R _o > 0.5, the wide-gap effect on the stability limit is predicted to be almost the same for non-Newtonian fluids as for Newtonian ones. The ratio on the critical Taylor numbers for non-Newtonian and Newtonian fluids: Ta _c (n) and Ta _c (n = 1) obey a generalized functional dependence: Ta _c (n)/Ta _c (n = 1) = g(n), where g(n) is a function corresponding to the solution for the narrow gap approximation.Theoretical predictions have been compared with experimental results for pseudoplastic liquids. In the range of the radius ratio R _i /R _o > 0.6 the theoretical stability limit is in good agreement with the experiments, however, for R _i /R _o < 0.6, the critical Taylor number is considerably lower than predicted by theory.     

The influence of flow-induced non-Newtonian fluid properties on turbulent drag reduction

Friction factors and velocity profiles in turbulent drag reduction can be compared to Newtonian fluid turbulence when the shear viscosity at the wall shear rate is used for the Reynolds number and the local shear viscosity is used for the non-dimensional wall distance. On this basis, an apparent maximum drag reduction asymptote is found which is independent of Reynolds number and type of drag reducing additive. However, no shear viscosity is able to account for the difference between the measured Reynolds stress and the Reynolds stress calculated from the mean velocity profile (the Reynolds stress deficit). If the appropriate local viscosity to use with the velocity fluctuation correlations includes an elongational component, the problem can be resolved. Taking the maximum drag reduction asymptote as a non-Newtonian flow, with this effective viscosity, leads to agreement with the concept of an asymptote only when the solvent viscosity is used in the non-dimensional wall distance.     

Flow behaviour of molten 2,4,6-trinitrotoluene (TNT) between concentric cylinders

The flow behaviour of pure and commercial molten TNT when subjected to very high rates of shear in a rotational viscometer over the temperature range 82.0 to 95.4°C is presented. All data obtained suggest that the behaviour of molten TNT is Newtonian, contrary to the conclusions of some published work, and the temperature dependence of the viscosity of pure TNT is adequately described by an Arrhenius-type relationship of the form = A e ^B/T whereA = 0.000 541,B = 3 570 andT is the Kelvin temperature. A similar relationship is obtained for commercial TNT. Under some instrumental conditions discontinuities are seen in the shear stress—shear rate flow curves. An analysis of these discontinuities shows them to be caused by the transition from laminar to turbulent flow. Possible implications for processibility and initiation of explosives are discussed.     

The steady shear viscosity of filled polymeric liquids described by a linear superposition of two relaxation mechanisms

Filled polymeric liquids often exhibit apparent yielding and shear thinning in steady shear flow. Yielding results from non-hydrodynamic particle—particle interactions, while shear thinning results from the non-Newtonian behavior of the polymer melt. A simple equation, based on the linear superposition of two relaxation mechanisms, is proposed to describe the viscosity of filled polymer melts over a wide range of shear rates and filler volume fraction.The viscosity is written as the sum of two generalized Newtonian liquid models. The resulting equation can describe a wide range of shear-thinning viscosity curves, and a hierarchy of equations is obtained by simplifying the general case. Some of the parameters in the equation can be related to the properties of the unfilled liquid and the solid volume fraction. One adjustable parameter, a yield stress, is necessary to describe the viscosity at low rates where non-hydrodynamic particle—particle interaction dominate. At high shear rates, where particle—particle interactions are dominated by interparticle hydrodynamics, no adjustable parameters are necessary. A single equation describes both the high and low shear rate regimes. Predictions of the equation closely fit published viscosity data of filled polymer melts. n power-law index - n ₁,n ₂ power-law index of first (second) term - shear rate - steady shear viscosity - ₀ zero-shear rate viscosity - _{0, 1}, _{0, 2} zero-shear rate viscosity of first (second) term - time constant - ₁, ₂ time constant of first (second) term - µ _r relative viscosity of filled Newtonian liquid - ₀ yield stress - ø solid volume fraction - ø _m maximum solid volume fraction     

On the relaxation of shear and normal stresses of viscoelastic fluids following constant shear rate experiments

By means of a cone and plate rheometer the relaxation of the shear stress and the first normal stress difference in polymer liquids upon cessation of a constant shear rate were examined. The experiments were conducted mostly in a high shear rate region of relevance for the processing of these materials. The relaxation behavior at these shear rates can only be measured accurately under extremely precise specifications of the rheometer. To determine under which conditions the integral normal thrust is a convenient measure for the relaxing local first normal stress difference the radial distribution of the pressure in the shear gap was measured. The shape of relaxation of both the shear stress and the first normal stress difference could be closely approximated for the entire measured shear rate and time range by a two parameter statistical function. In the range of measured shear rates, one of the parameters, the standard deviationS, is equal for the shear and the normal stress, and is independent of the shear rate within the limit of experimental error. The second parameter, the mean relaxation timet _50, of the shear stress andt _50, of the first normal stress difference, can be calculated approximately from the viscosity function and only a single relaxation experiment.     

Linear rheology of viscoelastic emulsions with interfacial tension

Emulsions of incompressible viscoelastic materials are considered, in which the addition of an interfacial agent causes the interfacial tension to depend on shear deformation and variation of area. The average complex shear modulus of the medium accounts for the mechanical interactions between inclusions by a self consistent treatment similar to the Lorentz sphere method in electricity. The resulting expression of the average modulus includes as special cases the Kerner formula for incompressible elastic materials and the Oldroyd expression of the complex viscosity of emulsions of Newtonian liquids in time-dependent flow.     

Experimental investigations of the stability limit of the helical flow of pseudoplastic liquids

The stability of the laminar helical flow of pseudoplastic liquids has been investigated with an indirect method consisting in the measurement of the rate of mass transfer at the surface of the inner rotating cylinder. The experiments have been carried out for different values of the geometric parameter = R ₁/R ₂ (the radius ratio) in the range of small values of the Reynolds number,Re < 200. Water solutions of CMC and MC have been used as pseudoplastic liquids obeying the power law model. The results have been correlated with the Taylor and Reynolds numbers defined with the aid of the mean viscosity value. The stability limit of the Couette flow is described by a functional dependence of the modified critical Taylor number (including geometric factor) on the flow indexn. This dependence, general for pseudoplastic liquids obeying the power law model, is close to the previous theoretical predictions and displays destabilizing influence of pseudoplasticity on the rotational motion. Beyond the initial range of the Reynolds numbers values (Re>20), the stability of the helical flow is not affected considerably by the pseudoplastic properties of liquids. In the range of the monotonic stabilization of the helical flow the stability limit is described by a general dependence of the modified Taylor number on the Reynolds number. The dependence is general for pseudoplastic as well as Newtonian liquids.Nomenclature C _i concentration of reaction ions, kmol/m³ - d = R ₂ –R ₁ gap width, m - F _M () Meksyn's geometric factor (Eq. (1)) - F ₀ Faraday constant, C/kmol - i _l density of limit current, A/m³ - k _c mass transfer coefficient, m/s - n flow index - R ₁,R ₂ inner, outer radius of the gap, m - Re = V _m ·2d·/µ _m Reynolds number - Ta _c = _c ·d^3/2·R ₁ ^1/2 ·/µ _m Taylor number - Z _i number of electrons involved in electrochemical reaction - = R ₁/R ₂ radius ratio - µ apparent viscosity (local), Ns/m² - µ _m mean apparent viscosity value (Eq. (3)), Ns/m² - µ _i apparent viscosity value at a surface of the inner cylinder, Ns/m² - density, kg/m³ - _c angular velocity of the inner cylinder (critical value), 1/s     

The squeezing flow of a model suspension fluid

The paper is concerned with the squeezing flow of a model suspension fluid. The numerical solution obtained by a time-dependent Boundary Element Method is compared to an asymptotic solution at large radius. It is found that the kinematics are Newtonian in character, and the fibres quickly align themselves radially. Consequently, the squeezing force is only weakly dependent on the initial orientations of the fibres and the device can be used for measuring the effective viscosity of the suspension. The effective viscosity found from the squeezing flow agrees surprisingly well with experimental data and numerical data derived from the falling sphere geometry at low volume fractions ( < 0.1).     

Rheological characterization of highly branched poly(ethyleneterephthalate)

Linear and highly branched poly(ethyleneterephthalate) samples were synthesized and characterized in terms of intrinsic viscosity, molecular weight and melt viscosity over a wide range of shear rates at several temperatures, in the range from 265° to 295 °C. Linear samples exhibited Newtonian behavior over a wide range of shear rates, while the branched ones became shear thinning at relatively low shear rates. Our experimental data, as well as data previously reported, were found to be described by a proposed correlation between the melt viscosity ratio and a branching index. Moreover, the activation energy for melt flow was found for the highly branched samples to be a little higher than that of the linear samples.     

A slit viscometer for the measurement of the viscosity of aqueous systems at high temperatures

A slit viscometer has been constructed to measure the viscosity of aqueous systems at temperatures up to 140 °C. Liquid is forced backwards and forwards through the slit by the use of varying air pressure. The flow rate is obtained from the time for the liquid to pass conductivity probes located in liquid reservoirs either side of the slit. The pressure difference between two points on the slit wall is determined using a differential pressure transducer. By varying the slit height measurements can be made on liquids with viscosities in the range 10 to 10^–3 Pa s. Shear rates from 10 to 10⁴ s^–1 can be achieved. A simple microcomputer control system enables the shear stress to be automatically increased and decreased stepwise. Representative data on polysaccharide solutions and strach suspensions are presented. The viscometer is particularly well-suited for following temperature-dependent biopolymer transitions and the thermal depolymerisation of water soluble polymers.     

Numerical solution for the flow of viscoelastic fluids around an inclined circular cylinder.

Finite difference solutions have been obtained by the perturbation method to investigate the influence of shear thinning and elasticity on the flow around an inclined circular cylinder of finite length in a uniform flow. In this numerical analysis a generalized upper-convected Maxwell model, in which the viscosity changes according to the Cross model, has been used.The local flow over the cylinder is only slightly deflected. However, in the wake flow behind the cylinder the particle path is remarkably influenced by the axial flow and rapidly flows up parallel to the cylinder's axis. Then it gradually rejoins direction of the incoming flow. It is found that viscoelastic fluids are prone to flow axially in the vicinity of the cylinder. The numerical predictions generally agree with the flow visualization results.The numerical solutions also demonstrate that elasticity has a strong effect on the velocity profile especially around both ends of the cylinder; elasticity increases the asymmetric profiles of both circumferential velocity and axial velocity with respect to equal to 90° and decreases a difference in the circumferential velocity between the windward end and the leeward end.For non-Newtonian fluids, the length of the wake flow is influenced by not only the Reynolds number but also the cylinder diameter and it is larger for the cylinder with the smaller diameter at the same Reynolds number.Partly presented at the 9th Australasian Fluid Mechanics Conference, University of Auckland, New Zealand, 8–12 December, 1986     

Newtonian stratified flow through an abrupt expansion

The present paper is devoted to the numerical simulations of stratified generalized Newtonian flow. The main feature of the algorithm is to include the coordinates of the interface as primitive unknowns of the flow problem together with the nodal velocity components and pressures calculated on a deformable finite element mesh. Newton-Raphson's iterative method is used for solving the non-linear problem. Special attention is given to the location of the intersection between the interface and a solid boundary, when it is unknown at the outset. The method is applied to the creeping stratified flow of two Newtonian fluids through a one-to-four abrupt expansion; the results remain valid for the contraction problem. It is found that, under appropriate conditions, the small Newtonian corner vortex can increase by a large factor, both in size and intensity; the degrees of freedom of the simulation are the ratios of flow-rate and of viscosity of the fluids.     

Flow of an inelastic Non-Newtonian fluid through an abrupt contraction: A recalculation

The axi-symmetric flows of Newtonian and Non-Newtonian fluids through a sudden one-to-four contraction are numerically simulated. As the Non-Newtonian constitutive equation the inelastic form of the four-constant Oldroyd implicit rheological model is used. Because of the Non-Newtonian viscosity, a single non-dimensional parameter cannot be found to characterize the equations of motion. Therefore in this work the equations of motion are solved using dimensional values, that is, with actual increase of the mass flow.     

Orthogonal superposition of small and large amplitude oscillations upon steady shear flow of polymer fluids

The orthogonal superposition of small and large amplitude oscillations upon steady shear flow of elastic fluids has been considered. Theoretical results, obtained by numerical methods, are based on the Leonov viscoelastic constitutive equation. Steady-state components, amplitudes and phase angles of the oscillatory components of the shear stress, the first and second normal stress differences as functions of shear rate, deformation amplitude and frequency have been calculated. These oscillatory components include the first and third harmonic of the shear stresses and the second harmonic of the normal stresses. In the case of small amplitude superposition, the effect of the steady shear flow upon the frequency-dependent storage modulus and dynamic viscosity has been determined and compared with experimental data available in literature for polymeric solutions. The predicted results have been found to be in fair agreement with the experimental data at low shear rates and only in qualitative agreement at high shear rates and low frequencies. A comparison of the present theoretical results has also been made with the predictions of other theories.In the case of large amplitude superposition, the effect of oscillations upon the steady shear flow characteristics has been determined, indicating that the orthogonal superposition has less influence on the steady state shear stresses and the first difference of normal stresses than the parallel superposition. However, in the orthogonal superposition a more pronounced influence has been observed for the second difference of normal stresses.     

Flow birefringence and rheological measurements on shear induced micellar structures

Aqueous solutions of cationic surfactant systems with strongly binding counterions show the striking phenomenon of shear induced phase transitions. At low shear rates or angular frequencies, the solutions exhibit Newtonian flow. At high rates of shear, however, the rheological properties change dramatically. Above a well defined threshold value of the velocity gradient, a supermolecular structure can be formed from micellar aggregates. This shear induced structure (SIS) behaves like a gel and exhibits strong flow birefringence. The formation of the shear induced structure is very complicated and depends on the specific conditions of the surfactant system. In this paper we discuss new results which have been obtained from rheological measurements and from flow birefringence data. We examine the stability of the shear induced state as a function of temperature, surfactant concentration and salt concentration and we analyse the effect of solubilisation of alcohols and hydrocarbons. The results are interpreted in terms of a kinetic model which accounts for the observed behavior.Dedicated to the 60. birthday of Prof. H. Harnisch, Hoechst AGPartly presented at the 2nd Conference of European Rheologists, Prague, June 17–20, 1986     

Viscosity measurements with a magnetoviscometer in the zero-shear and transition region of polypropylenes

Streaming of a non-Newtonian fluid around a sphere is of special importance not only for measuring viscosities with falling spheres, but also for many problems connected with polymer processing. Using the mentioned measuring principle, attention has to be paid to the following points: The sphere is moving in a fluid (melt) of finite extension which requires the application of wall and perhaps end corrections. These are possibly not the same for Newtonian and non-Newtonian fluids. To calculate the viscosity with the help of Stokes law the steady-state velocity is necessary, and it is essential, how long it takes the sphere to reach it. To compare our results with other data, an average shear rate has to be calculated, since there is no uniform shear rate around the sphere. Velocities being very low in our experiments result in very small Reynolds numbers (Re < 10^–3), which allows the application of Stokes law practically without corrections.The experiments were performed at zero shear and in the transition region above. It turned out, that it is usually not possible to extrapolate from shear-dependent viscosity data to zero-shear viscosity.Dedicated to Prof. A. Neckel on the occasion of his 60th birthday     

Characterization of yield stress fluids with concentric cylinder viscometers

The methods normally employed for shear rate calculations from concentric cylinder viscometer data generally are not applicable for fluids with a yield stress. In cylindrical systems with large radius ratios, as usually is the case with suspensions, the yield stress induces two possible flow regimes in the annulus. Unless the yield value is exceeded everywhere in the gap only part of the fluid can be sheared while the remaining region behaves like a solid plug. A correct calculation of the shear rate must take into account the presence of a variable effective gap width determined by the extent of the sheared layer. For time-independent yield stress fluids, a two-step procedure, which does not require any specific flow model, is proposed for analysing the experimental torque-speed data. Under the partially sheared condition, the shear rate can be computed exactly, whereas for the fully sheared flow the Krieger and Elrod approximation is satisfactory. The method is assessed by examining both semi-ideal data generated with a Casson fluid with known properties, and experimental data with an industrial suspension. A more complicated problem associated with characterization of time-dependent yield stress fluids is also identified and discussed. An approximate procedure is used to illustrate the dependence of the shear rate on time of shear in constant-speed experiments.     

The stability of the helical flow of pseudoplastic liquids in a narrow annular gap with a rotating inner cylinder

The stability of a laminar helical flow of pseudoplastic liquids in an annular gap with a rotating inner cylinder is investigated theoretically. The analysis is carried out under the assumption of a torroidal form of the secondary flow (torroidal Taylor vortices) for the narrow gap geometry. The power law model has been applied to describe the pseudoplasticity of liquids. The problem of the stability has been formulated with the aid of the method of small disturbances, and solved using the Galerkin method. In order to describe the stability limit the Reynolds and Taylor numbers defined with the aid of the mean viscosity value have been introduced. It has been found that pseudoplasticity has a considerably destabilizing influence on the Couette motion as well as on the helical flow in the initial range of the Reynolds number values (Re<30). A decrease of the flow index value,n, is accompanied by a decrease of the critical value of the Taylor number. This destabilizing effect of pseudoplasticity vanishes in the range of the larger values of the Reynolds number. In the rangeRe>30, the stability limit of the flow of pseudoplastic liquids can be described by a general dependence of the critical valueTa _c onRe, which is consistent with results obtained for the case of Newtonian fluids. a frequency number (Eq. (27)), 1/s - b wave number (Eq. (27)), 1/m - B = M/N parameter - d = R ₂ –R ₁ gap width, m - f(y, B, k) function of viscosity distribution (Eq. (7)) - f ₀ (x) function of viscosity distribution (narrow gap Eq. (35)) - F(x) = V(x)/V _m dimensionless distribution of axial flow velocity - G(x) = U(x) _i dimensionless distribution of angular flow velocity - K consistency coefficient, N sⁿ/m² - M = (P/L)R ₂ parameter of the stress field (Eq. (1)), N/m² - M ₀ torque per unit length, N - n flow index - N = M ₀/(2R ₂ ² ) parameter of the stress field (Eq. (1)), N/m² - p = 1/2n–1/2 parameter - pressure disturbance amplitude, N/m² - p pressure disturbance, N/m² - (P/L) pressure drop per unit length of the gap, N/m² - r radial coordinate, m - r _m location of the maximum value of the axial velocity, m - R ₁,R ₂ inner, outer radius of the annulus, m - Re = V _m 2d/ _m Reynolds number - S = (P/L · d/N) parameteer of the stress field (narrow gap) - t time, s - Ta = _i d ^3/2 R ₁ ^1/2 / _m Taylor number - U tangential velocity, m/s - U _i tangential velocity at the surface of the inner cylinder, m/s - V axial velocity, m/s - V _m mean axial velocity, m/s - V disturbance vector of velocity field, m/s - amplitude of theV _k -disturbance, m/s - X, Y, Z functions in Eqs. (36–38) - y = r/R ₂ dimensionless radial coordinate - x = (r—(R ₁+R ₂)/2)d radial coordinate (narrow gap) - L ₁ L ₄ linear operators in Eqs. (36–38) - = ad/V _m dimensionless frequency number - = b·d dimensionless wave number - component of the rate of strain tensor, 1/s - component of the rate of strain tensor corresponding to the disturbance, 1/s - = R ₁/R ₂ radius ratio - apparent viscosity, Ns/m² - ₀ apparent viscosity in the main flow, Ns/m² - µ disturbance of the apparent viscosity, Ns/m² - µ _m mean apparent viscosity, Ns/m² - density, kg/m³ - _ij component of the stress tensor, N/m² - angular velocity, rad/s - _i angular velocity of the inner cylinder, rad/s     

Messung der dynamischen Eigenschaften verdünnter Polymerlösungen

Zusammenfassung Ein neuartiges Rheometer zur Ermittlung der rheologischen Eigenschaften von Polymerlösungen im linear-viskoelastischen Bereich wird vorgestellt. Durch Anwendung der Laser-Doppler-Anemometrie, die eine im hydro-dynamischen Sinn störungsfreie Meßmethode darstellt, ist es möglich, niedrig-viskose bis hin zu wasserähnlichen Proben zu vermessen.Zur Bewältigung der in großer Zahl anfallenden Daten und Rechenoperationen findet ein Mikrocomputer-System Verwendung. Es erledigt im einzelnen die Aufgaben Versuchsablauf-Steuerung, Meßwerterfassung, Auswertung, Dokumentation und graphische Darstellung der Ergebnisse.Anhand von Messungen an newtonschen Flüssigkeiten werden der Funktionsnachweis erbracht und die Betriebsbereiche der Ringspaltsysteme unterschiedlichen Durchmessers ermittelt.Die viskoelastischen Eigenschaften von wäßrigen Polyethylenoxid- und Polyacrylamid-Lösungen niedriger Viskosität lassen sich über einen Frequenzbereich von 0,1 bis 100 Hz messen. Die Ergebnisse werden mit Hilfe der komplexen Viskositätsfunktion dargestellt. Daraus läßt sich als gleichwertige Darstellung das diskrete Relaxationsspektrum eines konkreten Stoffgesetzes gewinnen.

---

A novel rheometer for determining the elastic characteristics of polymeric solutions in the linear-viscoelastic region is described. Laser-Doppler anemometry, which does not introduce hydrodynamic disturbances, is used to enable low viscosity liquids including water-like samples to be measured.A microcomputer system is utilized to control the experiments, store and analyse the measured data, and provide graphical representations of the results. Measurements on Newtonian liquids verified the validity of the method and allowed the operational regions of the annulus systems with different diameters to be determined.The elastic characteristics of low viscosity aqueous solutions of polyethyleneoxide and polyacrylamide can be measured at frequencies from 0.1 to 100 Hz. The results are presented using the complex viscosity function. As a result the discrete relaxation spectrum of a special material law can be obtained as an equivalent representation.