Effect of pore packing defects in 2-d ordered mesoporous carbons on ionic transport

Ordered mesoporous materials show great importance in energy, environmental, and chemical engineering. The diffusion of guest species in mesoporous networks plays an important role in these applications, especially for energy storage, such as supercapacitors based on ordered mesoporous carbons (OMCs). The ion diffusion behavior in two different 2-D hexagonal OMCs was investigated by using cyclic voltametry and electrochemical impedance spectroscopy. In addition, transmission electron microscopy, small-angle X-ray diffraction, and nitrogen cryosorption methods were used to study the pore structure variations of these two OMCs. It was found that, for the OMC with defective pore channels (termed as pore packing defects), the gravimetric capacitance was greatly decayed when the voltage scan rate was increased. The experimental results suggest that, for the ion diffusion in 2-D hexagonal OMCs with similar mesopore size distribution, the pore packing defect is a dominant dynamic factor.     

A heterogeneous model for gas transport in carbon molecular sieves

A dual resistance model with distribution of either barrier or pore diffusional activation energy is proposed in this work for gas transport in carbon molecular sieve (CMS) micropores. This is a novel approach in which the equilibrium is homogeneous, but the kinetics is heterogeneous. The model seems to provide a possible explanation for the concentration dependence of the thermodynamically corrected barrier and pore diffusion coefficients observed in previous studies from this laboratory on gas diffusion in CMS. The energy distribution is assumed to follow the gamma distribution function. It is shown that the energy distribution model can fully capture the behavior described by the empirical model established in earlier studies to account for the concentration dependence of thermodynamically corrected barrier and pore diffusion coefficients. A methodology is proposed for extracting energy distribution parameters, and it is further shown that the extracted energy distribution parameters can effectively predict integral uptake and column breakthrough profiles over a wide range of operating pressures.     

Mesoporous carbon nanosheet-assembled flowers towards superior potassium storage

Potassium-ion batteries(PIBs) are attracted tremendous interest for large-scale energy storage systems(ESSs) owing to their economic merits.However,the main challenges of the PIBs are sluggish K-ion diffusion and large volume variations in the potassium repeated intercalation/deintercalation.Herein,mesoporous carbon nanosheet-assembled flowers(abbreviated as F-C) are designed as an original anode for superior-performance PIBs.Specifically,the F-C anode exhibits a high K-storage capacity(e.g.,381 mAh/g at 50 mA/g during the 2~(nd) cycle),excellent rate performance(e.g.,101 mAh/g at 2.0 A/g) and superior long cycle capability.Such excellent K-ion storage property is largely benefited from the large surface area(～141 m~2/g) and reasonable pore volume(0.465 cm~3/g),which not only stimulates rapid Kions diffusion and relieves the huge volume strain,but also exposes extensive active sites for K-ion capacitive storage.     

Simulations of Guest Transport in Clathrates of Dianin’s Compound and Hydroquinone

Clathrates have been proposed for use in a variety of applications including gas storage, mixture separation and catalysis due to the potential for controlled guest diffusion through their porous lattices. Here molecular dynamics simulations are employed to study guest transport in clathrates of hydroquinone (HQ) and Dianin’s compound (DC). Systems investigated were HQ with methanol and acetonitrile, and DC with methanol and ethanol. Simulations were set up with one guest in the pore, two guests in the pore and one vacancy in the pore and a filled pore, and free‐energy barriers for movement between cavities of the pore were estimated for all cases. Comparison between these simulations indicates that guest transport most likely proceeds by molecules moving from full to empty cavities consecutively, one by one, rather than in a concerted manner. Thus, the presence of empty cavities is very important for guest transport, which becomes more energetically demanding in fully loaded systems. Flexibility of the host can assist guest transport. In the studied DC clathrates transport occurs via an intermediate conformation in which the hydroxyl group of the alcohol guest molecule participates in the hydrogen‐bonded ring of the host. We also address the issue of the number of methanol guest molecules that DC accommodates, for which conflicting information exists. We found that this is likely to be temperature dependent and suggest that under some conditions the system is most likely non‐stoichiometric.     

Rational Design of Covalent Organic Frameworks as Gas Diffusion Layers for Multi-atmosphere Lithium-Air Batteries

Non-aqueous Li-air batteries, despite their high energy density and low cost, have not been deployed practically due to their instability in ambient air, where moisture causes parasitic reactions and shortens their life drastically. Here, we demonstrate the rational design of nanoporous covalent organic frameworks (COFs) as effective gas diffusion layers (GDLs) to address this constraint. The COF GDLs, with a tailor-made pore size of ≈1.4 nm and superhydrophobicity, can limit the intrusion of organic electrolytes and moisture into the gas diffusion channels, enabling high capacity, fast kinetics, and excellent stability of the Li-air batteries. Moreover, we achieve multi-atmosphere Li-air batteries, which can stably cycle under open ambient air (relative humidity up to 95 %) and even in various atmospheres with looping oxygen, humid air, and carbon dioxide. The design principles of our COF GDLs can be universally applied in energy storage and electrochemical systems using organic electrolytes.     

Radical Covalent Organic Frameworks: A General Strategy to Immobilize Open‐Accessible Polyradicals for High‐Performance Capacitive Energy Storage

Ordered π‐columns and open nanochannels found in covalent organic frameworks (COFs) could render them able to store electric energy. However, the synthetic difficulty in achieving redox‐active skeletons has thus far restricted their potential for energy storage. A general strategy is presented for converting a conventional COF into an outstanding platform for energy storage through post‐synthetic functionalization with organic radicals. The radical frameworks with openly accessible polyradicals immobilized on the pore walls undergo rapid and reversible redox reactions, leading to capacitive energy storage with high capacitance, high‐rate kinetics, and robust cycle stability. The results suggest that channel‐wall functional engineering with redox‐active species will be a facile and versatile strategy to explore COFs for energy storage.     

恒电位阶跃法研究贮氢合金MlNi_(3.75)Co_(0.65)Mn_(0.4)Al_(0.2)中氢的扩散行为

本文用恒电位阶跃法研究了不同放电深度 (DOD)和不同温度下贮氢合金MlNi3.75Co0 .6 5Mn0 .4 Al0 .2 中氢的扩散行为 .结果表明 :室温下该合金中氢的扩散系数随DOD的增大而增大 ,在5 0 %DOD的该合金中 ,氢的扩散系数随温度的升高而增大 ,扩散活化能为 19.87kJ/mol     

Colloidal Supercapattery: Redox Ions in Electrode and Electrolyte

Redox chemistry is the cornerstone of various electrochemical energy conversion and storage systems, associated with ion diffusion process. To actualize both high energy and power density in energy storage devices, both multiple electron transfer reaction and fast ion diffusion occurred in one electrode material are prerequisite. The existence forms of redox ions can lead to different electrochemical thermodynamic and kinetic properties. Here, we introduce novel colloid system, which includes multiple varying ion forms, multi‐interaction and abundant redox active sites. Unlike redox cations in solution and crystal materials, colloid system has specific reactivity‐structure relationship. In the colloidal ionic electrode, the occurrence of multiple‐electron redox reactions and fast ion diffusion leaded to ultrahigh specific capacitance and fast charge rate. The colloidal ionic supercapattery coupled with redox electrolyte provides a new potential technique for the comprehensive use of redox ions including cations and anions in electrode and electrolyte and a guiding design for the development of next‐generation high performance energy storage devices.     

Recent Advances in Porous Carbon Materials for Electrochemical Energy Storage

Climate change and the energy crisis have promoted the rapid development of electrochemical energy‐storage devices. Owing to many intriguing physicochemical properties, such as excellent chemical stability, high electronic conductivity, and a large specific surface area, porous carbon materials have always been considering as a promising candidate for electrochemical energy storage. To date, a wide variety of porous carbon materials based upon molecular design, pore control, and compositional tailoring have been proposed for energy‐storage applications. This focus review summarizes recent advances in the synthesis of various porous carbon materials from the view of energy storage, particularly in the past three years. Their applications in representative electrochemical energy‐storage devices, such as lithium‐ion batteries, supercapacitors, and lithium‐ion hybrid capacitors, are discussed in this review, with a look forward to offer some inspiration and guidelines for the exploitation of advanced carbon‐based energy‐storage materials.     

Storage of hydrogen at 303 K in graphite slitlike pores from grand canonical Monte Carlo simulation

Grand canonical Monte Carlo (GCMC) simulations were used for the modeling of the hydrogen adsorption in idealized graphite slitlike pores. In all simulations, quantum effects were included through the Feynman and Hibbs second-order effective potential. The simulated surface excess isotherms of hydrogen were used for the determination of the total hydrogen storage, density of hydrogen in graphite slitlike pores, distribution of pore sizes and volumes, enthalpy of adsorption per mole, total surface area, total pore volume, and average pore size of pitch-based activated carbon fibers. Combining experimental results with simulations reveals that the density of hydrogen in graphite slitlike pores at 303 K does not exceed 0.014 g/cm(3), that is, 21% of the liquid-hydrogen density at the triple point. The optimal pore size for the storage of hydrogen at 303 K in the considered pore geometry depends on the pressure of storage. For lower storage pressures, p < 30MPa, the optimal pore width is equal to a 2.2 collision diameter of hydrogen (i.e., 0.65 nm), whereas, for p congruent with 50MPa, the pore width is equal to an approximately 7.2 collision diameter of hydrogen (i.e., 2.13 nm). For the wider pores, that is, the pore width exceeds a 7.2 collision diameter of hydrogen, the surface excess of hydrogen adsorption is constant. The importance of quantum effects is recognized in narrow graphite slitlike pores in the whole range of the hydrogen pressure as well as in wider ones at high pressures of bulk hydrogen. The enthalpies of adsorption per mole for the considered carbonaceous materials are practically constant with hydrogen loading and vary within the narrow range q(st) congruent with 7.28-7.85 kJ/mol. Our systematic study of hydrogen adsorption at 303 K in graphite slitlike pores gives deep insight into the timely problem of hydrogen storage as the most promising source of clean energy. The calculated maximum storage of hydrogen is equal to approximately 1.4 wt %, which is far from the United States Department of Energy (DOE) target (i.e., 6.5 wt %), thus concluding that the total storage amount of hydrogen obtained at 303 K in graphite slitlike pores of carbon fibers is not sufficient yet.     

Molecular simulation of adsorption and diffusion of hydrogen in metal-organic frameworks

Metal-organic frameworks (MOFs) are thought to be a set of promising hydrogen storage materials; however, little is known about the interactions between hydrogen molecules and pore walls as well as the diffusivities of hydrogen in MOFs. In this work, we performed a systematic molecular simulation study on the adsorption and diffusion of hydrogen in MOFs to provide insight into molecular-level details of the underlying mechanisms. This work shows that metal-oxygen clusters are preferential adsorption sites for hydrogen in MOFs, and the effect of the organic linkers becomes evident with increasing pressure. The hydrogen storage capacity of MOFs is similar to carbon nanotubes, which is higher than zeolites. Diffusion of hydrogen in MOFs is an activated process that is similar to diffusion in zeolites. The information derived in this work is useful to guide the future rational design and synthesis of tailored MOF materials with improved hydrogen adsorption capability.     

二维金属有机框架纳米片的合成及在超电容和电催化领域的应用

二维金属有机框架(2D MOF)纳米片具有丰富且易暴露的表面活性位点、 高度有序的孔结构以及多样且可调的化学成分, 在电化学能量存储与转化中有利于降低反应电位, 提高扩散速率和反应速率. 关于2D MOF应用于电化学存储与转化的研究已有大量报道. 本文综合评述了近几年2D MOF的合成进展及其在超电容(SC)、 析氧反应(OER)、 析氢反应(HER)、 氧还原反应(ORR)和二氧化碳还原反应(CRR)的应用, 并对2D MOF作为电催化材料的研究现状和发展前景进行了总结与展望.     

碳化硅衍生碳/球形天然石墨复合材料的制备及其结构调控

为满足储能领域对于材料兼具高能量密度和高功率密度的需求, 本文旨在将具有特殊孔隙结构的碳化物衍生碳与具有高导电性和高能量存储密度的石墨化碳(球形天然石墨)相复合, 制备得到一种多孔碳化硅衍生碳/球形天然石墨(SiC-CDCs@NG)复合材料. 采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、拉曼光谱、N₂吸/脱附等方法对材料的组成、结构、形貌、孔结构和比表面积等进行了表征. 结果表明,SiC-CDCs@NG材料具有较大的且可调节的比表面积和微孔体积, 微孔孔径集中在0.5-0.7 nm范围内; 通过改变NG/Si 摩尔比, 可以有效调控CDCs壳和NG核在复合材料中的组成分布、CDCs微孔的体积、孔径分布和比表面积.     

About the Dominance of Mesopores in Physisorption in Amorphous Materials

Amorphous, porous materials represent by far the largest proportion of natural and men-made materials. Their pore networks consists of a wide range of pore sizes, including meso- and macropores. Within such a pore network, material moisture plays a crucial role in almost all transport processes. In the hygroscopic range, the pores are partially saturated and liquid water is only located at the pore fringe due to physisorption. Therefore, material parameters such as porosity or median pore diameter are inadequate to predict material moisture and moisture transport. To quantify the spatial distribution of material moisture, Hillerborg’s adsorption theory is used to predict the water layer thickness for different pore geometries. This is done for all pore sizes, including those in the lower nanometre range. Based on this approach, it is shown that the material moisture is almost completely located in mesopores, although the pore network is highly dominated by macropores. Thus, mesopores are mainly responsible for the moisture storage capacity, while macropores determine the moisture transport capacity, of an amorphous material. Finally, an electrical analogical circuit is used as a model to predict the diffusion coefficient based on the pore-size distribution, including physisorption.     

Substituent engineering of covalent organic frameworks modulates the crystallinity and electrochemical reactivity

Covalent organic frameworks(COFs)are emerging as powerful electrochemical energy storage/conversion materials benefiting from the controlled pore and chemical structures,which are usually determined by the regulation of the molecular building blocks.In contrast,the substituents are not considered significant for the electrochemical reactivity as they are usually removed during carbonization,which is necessary for improving the electrical conductivity of an electrode material.Here we show that the substituents play key roles not only in synthesizing COFs but also in controlling the COF structures during carbonization and thus the related electrochemical reactivity.Five characteristic substituents were used when synthesizing a new COF structure and it was found that electron-withdrawing strength of the substituents significantly influences the crystallinity of the COFs by tuning the reactivity of building blocks,or even determines whether the crystalline COF can be constructed.Moreover,the differences in chemical groups,sizes,and thermal stabilities of the substituents result in varied pore-collapse behaviors and the structures of the carbonized COFs,which show diverse effects on the electrochemical performances.An optimal material shows the highest surface area of 2131 m²/g,rich pores around 1 nm,and the highest ratio of sp² carbon among the samples,corresponding to the largest double-layer specific capacity over 125 F/g in an ionic liquid electrolyte,while another material with the lowest surface area and N-doping level exhibits a high H₂O₂ production selectivity over 80%through selective oxygen reduction.This study shows guiding significance for the design of building blocks and substituents for COFs and further the carbonized carbons,and also exhibits the great potential of substituent engineering in modulating the electrochemical reactivity.     

金属-有机骨架材料中吸附气体的扩散速率

采用分子动力学方法,以甲烷为探针分子研究了不同压力条件下气体在具有不同孔道结构的金属-有机骨架材料(MOFs)中的扩散速率.通过计算气体在八种材料中的自扩散系数,并结合气体分子在材料中的质心分布图等,讨论了气体扩散速率与孔道结构之间的关系.研究结果表明:对于同时含有孔笼(pocket)和三维正交孔道(channel)结构的MOF材料(P-C材料),低压时甲烷气体吸附在孔笼结构中,随着压力的升高,气体分子开始进入正交孔道,同时其自扩散系数增加;而对于只含有三维立方孔道结构的IRMOF(isoreticular MOF)系列材料,在中低压范围内,气体分子在其中的自扩散系数随压力变化较小.当压力进一步升高时,气体分子在材料孔道中的吸附逐渐接近饱和,其自扩散系数均降低.因此,在不同MOF材料中气体分子扩散速率的差异主要取决于孔道结构的不同.对P-C材料,中低压下通过控制压力可以控制气体在其中的扩散速率,从而为MOF材料在气体存储、分离等方面的实际应用提供参考信息.     

Optimization of slitlike carbon nanopores for storage of hythane fuel at ambient temperatures

Carbons with slitlike pores can serve as effective host materials for storage of hythane fuel, a bridge between the petrol combustion and hydrogen fuel cells. We have used grand canonical Monte Carlo simulation for the modeling of the hydrogen and methane mixture storage at 293 K and pressure of methane and hydrogen mixture up to 2 MPa. We have found that these pores serve as efficient vessels for the storage of hythane fuel near ambient temperatures and low pressures. We find that, for carbons having optimized slitlike pores of size H congruent with 7 A (pore width that can accommodate one adsorbed methane layer), and bulk hydrogen mole fraction >or=0.9, the volumetric stored energy exceeds the 2010 target of 5.4 MJ dm(-3) established by the U.S. FreedomCAR Partnership. At the same condition, the content of hydrogen in slitlike carbon pores is approximately = 7% by energy. Thus, we have obtained the composition corresponding to hythane fuel in carbon nanospaces with greatly enhanced volumetric energy in comparison to the traditional compression method. We proposed the simple system with added extra container filled with pure free/adsorbed methane for adjusting the composition of the desorbed mixture as needed during delivery. Our simulation results indicate that light slit pore carbon nanomaterials with optimized parameters are suitable filling vessels for storage of hythane fuel. The proposed simple system consisting of main vessel with physisorbed hythane fuel, and an extra container filled with pure free/adsorbed methane will be particularly suitable for combustion of hythane fuel in buses and passenger cars near ambient temperatures and low pressures.     

有机微孔聚合物研究进展

有机微孔聚合物(MOPs)是一类新型的多孔材料,具有合成方法多样、化学和物理性质稳定、孔尺寸可调控、表面可修饰等优点。近年来,MOPs在物理吸附储存气体方面表现出巨大潜力,从而在储氢和温室气体封存方面成为研究的热点之一。本文首先介绍了MOPs的结构类型及特点,分别介绍了自具微孔聚合物、超交联聚合物、共价有机网络以及共轭微孔聚合物的最新进展,分析结构与性能间的关系,并对其在催化、分离和气体储存方面的应用做了简单总结。最后对MOPs未来的研究进行了展望。     

Multicomponent effective medium-correlated random walk theory for the diffusion of fluid mixtures through porous media

Molecular transport in nanoconfined spaces plays a key role in many emerging technologies for gas separation and storage, as well as in nanofluidics. The infiltration of fluid mixtures into the voids of porous frameworks having complex topologies is common place to these technologies, and optimizing their performance entails developing a deeper understanding of how the flow of these mixtures is affected by the morphology of the pore space, particularly its pore size distribution and pore connectivity. Although several techniques have been developed for the estimation of the effective diffusivity characterizing the transport of single fluids through porous materials, this is not the case for fluid mixtures, where the only alternatives rely on a time-consuming solution of the pore network equations or adaptations of the single fluid theories which are useful for a limited type of systems. In this paper, a hybrid multicomponent effective medium-correlated random walk theory for the calculation of the effective transport coefficients matrix of fluid mixtures diffusing through porous materials is developed. The theory is suitable for those systems in which component fluxes at the single pore level can be related to the potential gradients of the different species through linear flux laws and corresponds to a generalization of the classical single fluid effective medium theory for the analysis of random resistor networks. Comparison with simulation of the diffusion of binary CO(2)/H(2)S and ternary CO(2)/H(2)S/C(3)H(8) gas mixtures in membranes modeled as large networks of randomly oriented pores with both continuous and discrete pore size distributions demonstrates the power of the theory, which was tested using the well-known generalized Maxwell-Stefan model for surface diffusion at the single pore level.     

Relation between pore sizes of protein crystals and anisotropic solute diffusivities

The diffusion of a solute, fluorescein, into lysozyme protein crystals with different pore structures was investigated. To determine the diffusion coefficients, three-dimensional solute concentration fields acquired by confocal laser scanning microscopy (CLSM) during diffusion into the crystals were compared with the output of a time-dependent 3-D diffusion model. The diffusion process was found to be anisotropic, and the degree of anisotropy increased in the order: triclinic, tetragonal and orthorhombic crystal morphology. A linear correlation between the pore diffusion coefficients and the pore sizes was established. The maximum size of the solute, deduced from the established correlation of diffusion coefficients and pore size, was 0.73 +/- 0.06 nm, which was in the range of the average diameter of fluorescein (0.69 +/- 0.02 nm). This proves that size exclusion is the key mechanism for solute diffusion in protein crystals. Hence, the origin of solute diffusion anisotropy can be found in the packing of the protein molecules in the crystals, which determines the crystal pore organization.