用PIV测试涡旋波流场的速度和剪应力分布

采用PIV瞬态流场测试技术,对二维槽道中的涡旋波流场不同相位上的速度分布和应力分布进行了测试和计算,本文定量地描述了槽道中涡旋波的形成过程及发展规律。通过调整振荡流的振幅和活塞行程,分析了Re数和Sr数对涡旋波流动的影响,得出了槽道内剪应力的分布状况以及平均剪切应力的周期性变化规律。深入分析了涡旋波流场强化传递现象的本质。     

应用PIV技术测试涡旋波流场

涡旋波流动作为一种特殊的流动现象,可以使流体在相对较宽的槽道中产生较强的波动和对流混合,从而在小Re数条件下起到强化传质的效果。本文利用PIV流场显示技术,对振荡流在非对称槽道中所形成的涡旋波的产生机理和发展规律进行了实验研究和定量分析,测得了涡旋波流场的速度矢量图,阐明了涡旋波流场周期性变化的特点。分析了Re数和St数对涡旋波流动的影响,并得出了旋涡涡心位置以及涡心处涡量的动态变化规律。     

槽道内涡波流场的POD分析

对槽道内涡波流场的瞬态速度矢量场进行了2DPIV测量实验,将2DPIV测量的矢量场数据进行POD分析,根据POD分解的各阶模态的能量比确定了表征涡波流场主导结构的前15阶模态。结果表明,POD分解的前15阶模态发现槽道内涡波流场是由槽道壁面剪切层诱导的涡列以及伴随的波状主流组成;流场中大尺度的涡旋发展为涡对,对波状主流的脉动频率产生影响;根据涡波流场中的驻点和鞍点,获取了流场的大尺度涡对、平均流场以及Helmholtz涡环等明显特征;最后根据POD分解的前15阶模态对槽道内涡波流场进行重组,重组流场表征了槽道内层流状态下波状主流的形态和涡旋共存的涡波结构以及驻点和鞍点的位置处涡旋的变化等主要特征,有效地剔除了PIV测量流场中的随机信息,保留了PIV测量流场的主导特征。     

槽道内涡波流场的POD分析

对槽道内涡波流场的瞬态速度矢量场进行了2DPIV测量实验,将2DPIV测量的矢量场数据进行POD分析,根据POD分解的各阶模态的能量比确定了表征涡波流场主导结构的前15阶模态。结果表明,POD分解的前15阶模态发现槽道内涡波流场是由槽道壁面剪切层诱导的涡列以及伴随的波状主流组成;流场中大尺度的涡旋发展为涡对,对波状主流的脉动频率产生影响;根据涡波流场中的驻点和鞍点,获取了流场的大尺度涡对、平均流场以及Helmholtz涡环等明显特征;最后根据POD分解的前15阶模态对槽道内涡波流场进行重组,重组流场表征了槽道内层流状态下波状主流的形态和涡旋共存的涡波结构以及驻点和鞍点的位置处涡旋的变化等主要特征,有效地剔除了PIV测量流场中的随机信息,保留了PIV测量流场的主导特征。     

碳纳米管增强Nb-Si基复合材料界面应力传递的研究

基于均匀化理论,建立了碳纳米管增强Nb-Si基复合材料的代表体积元模型,并采用剪切滞后模型对碳纳米管增强Nb-Si基复合材料界面上的应力分布和传递机制进行了研究,探讨了分子间作用力、杨氏模量比β、长径比α、体积分数?等对其应力分布和传递机制的影响。结果表明,复合材料界面应力分布的变化主要集中在碳纳米管的两端,最大的应力都是分布在加载端或拔出端,然后向另一端传递;分子间作用力、杨氏模量比、长径比、体积分数等参数对界面应力的传递均有一定的影响,其中长径比和体积分数的影响最明显,体积分数为0.02时拔出端的界面剪切应力值相对于体积分数为0.0025时增大幅度达到近7倍,而长径比从200减小到50时,其应力传递距离增大了近8倍。     

非对称槽道中涡旋波的特性研究

利用PIV流场显示技术，对振荡流体在非对称槽道中涡旋波的产生、发展和消失的规律进 行了实验研究和分析，测得了涡旋波流场的速度矢量图，阐明了涡旋波流场周期性变化的特 点. 结合涡动力学方程，深入分析并揭示了做周期性运动的流体能在槽道中产生波的特性这 一规律，从中发现：流体周期变化的非定常性和不对称的槽道结构是形成涡旋波流动的主要 因素. 本文对涡旋波流场中各个旋涡的速度分布和涡量进行了测量和计算，分析了涡旋波 强化传质的机理，并研究了Re数对涡旋波流动的影响     

二维后向台阶流流动特性的实验研究

利用PIV技术,通过系统对150相似文献   

低Reynolds数NACA0012翼型绕流的流动特性分析

在水槽中应用PIV测速技术研究了NACA0012翼型在Reynolds数为8200时的流动特性,重点关注了翼型绕流结构中主频和扰动增长速率随迎角的变化。结果表明,分离剪切层的扰动增长符合指数规律;且随着迎角的增大,转捩过程加速,表现为扰动增长率逐渐增大,转捩的起始位置逐渐向上游移动。在所有实验迎角情况下,流场均由脱落旋涡主导,但其主导作用随着迎角的增大而削弱。     

大尺寸液桥热毛细对流失稳性地面实验研究

开展大尺寸液桥浮力-热毛细对流地面实验, 探究流场转捩的临界条件及临界状态附近的流动情况. 通过粒子图像测速方法(PIV) 获得流体速度场, 研究液桥内部定常和转捩后的流场结构以及流体运动规律;并用红外热像仪测量液桥自由面温度分布, 研究流体流动的时空演化和温度振荡. 实验发现大尺寸半浮区液桥浮力-热毛细对流临界值与几何参数有关, 在大普朗特(Prandtl) 数情况下, 流场存在由稳定态向不稳定态再到混沌的转捩过程, 在临界马兰哥尼(Marangoni) 数附近, 流场内会出现行波现象, 流动模式也会随高径比的变化而发生变化;当继续增大马兰哥尼数, 流动会进入混沌状态.      

混杂短纤维增强复合材料弹性模量预测

在现代工程结构中,纤维增强复合材料具有较高的刚度重量比、优异的耐久性和设计灵活性等优点,因此得到了广泛应用．本文结合细观力学中的Mori-Tanaka方法和Halpin-Tsai方法推导了混杂碳纤维和玻璃纤维增强复合材料有效弹性模量的解析表达式．通过引入参数λ,提出了计算随机方向混合纤维增强复合材料弹性模量的新模型,分析了纤维长径比和体积分数对复合材料弹性模量的影响．结果表明,复合材料的弹性性能对纤维长径比和体积分数非常敏感．根据提出的理论,混杂纤维增强复合材料的弹性模量处于单一纤维（纯碳纤维或纯玻璃纤维）增强复合材料弹性模量之间．对于单一纤维增强复合材料,采用Halpin-Tsai方法计算的复合材料弹性模量高于Mori-Tanaka方法计算结果．     

The 7th International Conference on Fluid Mechanics May 24-27,2015,Qingdao,China

正http://www.icfm7.org First Announcement and Call for PapersThe objective of International Conference on Fluid Mechanics(ICFM)is to provide a forum for researchers to exchange new ideas and recent advances in the fields of theoretical,experimental,computational Fluid Mechanics as well as interdisciplinary subjects.It was successfully convened by the Chinese Society of Theoretical and Applied Mechanics(CSTAM)in Beijing(1987,     

INFORMATION FOR CONTRIBUTORS

Contributions： The Journal, Acta Mechanica Solida Sinica, is pleased to receive papers from engineers and scientists working in various aspects of solid mechanics. All contributions are subject to critical review prior to acceptance and publication.     

Preface

This special issue of PARTICUOLOGY is devoted to the first UK-China Particle Technology Forum taking place in Leeds, UK, on 1-3 April 2007. The forum was initiated by a number of UK and Chinese leading academics and organised by the University of Leeds in collaboration with Chinese Society of Particuology, Particle Technology Subject Group （PTSG） of the Institution of Chemical Engineers （IChemE）, Particle Characterisation Interest Group （PCIG） of the Royal Society of Chemistry （RSC） and International Fine Particle Research Institute （IFPRI）. The forum was supported financially by the Engineering and Physics Sciences Research Council （EPSRC） of United Kingdom,     

基于鲁棒滤波的捷联导引头视线角速度估计方法

针对捷联导引头无法直接获取视线角速度等信息的问题,研究了鲁棒滤波在大气层外飞行器捷联导引头视线角速度估计中的应用。为了建立非线性滤波估计模型,考虑目标视线角速度的慢变特性,采用一阶马尔科夫模型建立了状态方程;推导了视线角速度的解耦模型,并建立了量测方程;考虑到实际应用中存在系统噪声统计特性失准的问题,基于Huber-Based鲁棒滤波方法,设计了视线角速度滤波器,并完成了基于Huber-Based滤波方法和扩展卡尔曼滤波方法的数学仿真。仿真结果表明Huber-Based滤波方法的视线角、视线角速度及视线角加速度估计精度分别达到0.1140'、0.1423'/s、0.0203'/s2,而扩展卡尔曼滤波方法的视线角、视线角速度及视线角加速度估计精度仅分别为0.6577'、0.6415'/s、0.0979'/s~2。仿真结果证明了该方法可以有效地估计出相对视线角速度等信息,并且在非高斯噪声的条件下,依然可获得较高的估计精度,具有一定的鲁棒性。     

Guide for authors

正Each of the sections below provides essential information for authors.We recommend that you take the time to read them before submitting a contribution to Acta Mechanica Sinica.We hope our guide to authors may help you navigate to the appropriate section.How to prepare a submission This document provides an outline of the editorial process involved in publishing a scientific paper in Acta Mechanica     

Use specification of multiscale materials for life spanned over macro-, micro-, nano-, and pico-scale

Multiscale material intends to enhance the strength and life of mechanical systems by matching the transmitted spatiotemporal energy distribution to the constituents at the different scale, say—macro, micro, nano, and pico,—, depending on the needs. Lower scale entities are, particularly, critical to small size systems. Large structures are less sensitive to microscopic effects. Scale shifting laws will be developed for relating test data from nano-, micro-, and macro-specimens. The benefit of reinforcement at the lower scale constituents needs to be justified at the macroscopic scale. Filling the void and space in regions of high energy density is considered.Material inhomogeneity interacts with specimen size. Their combined effect is non-equilibrium. Energy exchange between the environment and specimen becomes increasingly more significant as the specimen size is reduced. Perturbation of the operational conditions can further aggravate the situation. Scale transitional functions and/or f_j/j+1 are introduced to quantify these characteristics. They are represented, respectively, by , and (f_mi/ma,f_na/mi,f_pi/na). The abbreviations pi, na, mi, and ma refer to pico, nano, micro and macro.Local damage is assumed to initiate at a small scale, grows to a larger scale, and terminate at an even larger scale. The mechanism of energy absorption and dissipation will be introduced to develop a consistent book keeping system. Compaction of mass density for constituents of size 10⁻¹², 10⁻⁹, 10⁻⁶, 10⁻³ m, will be considered. Energy dissipation at all scales must be accounted for. Dissipations at the smaller scale must not only be included but they must abide by the same physical and mathematical interpretation, in order to avoid inconsistencies when making connections with those at the larger scale where dissipations are eminent.Three fundamental Problems I, II, and III are stated. They correspond to the commonly used service conditions. Reference is made to a Representative Tip (RT), the location where energy absorption and dissipation takes place. The RT can be a crack tip or a particle. At the larger size scales, RT can refer to a region. Scale shifting of results from the very small to the very large is needed to identify the benefit of using multiscale materials.