Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟

以CexZr1-xO2固溶体做载体,制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂(x=1,0.75,0.5,0.25,0).应用Brunauer-Emmet-Teller(BET)比表面积分析、X射线衍射(XRD)和H2程序升温还原(H2-TPR)等手段对催化剂进行相关表征,并系统研究了催化剂在饮食油烟催化燃烧中的催化活性.BET结果表叫催化剂的比表面积随Ce/Zr摩尔比的减小而减小.XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上.H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好.催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧,降低了反应温度.随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化,催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2＞Pt/γ-Al2O3/Ce0.25Zr0.75O2＞Pt/γ-Al2O3/Ce0.75Zr0.25O2＞Pt/γ-Al2O3/CeO2＞Pt/γ-Al2O3/ZrO2.     

Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟（英文）

以CexZr1-xO2固溶体做载体,制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂（x=1,0.75,0.5,0.25,0）.应用Brunauer-Emmet-Teller（BET）比表面积分析、X射线衍射（XRD）和H2程序升温还原（H2-TPR）等手段对催化剂进行相关表征,并系统研究了催化剂在饮食油烟催化燃烧中的催化活性.BET结果表明催化剂的比表面积随Ce/Zr摩尔比的减小而减小.XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上.H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好.催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧,降低了反应温度.随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化,催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2〉Pt/γ-Al2O3/Ce0.25Zr0.75O2〉Pt/γ-Al2O3/Ce0.75Zr0.25O2〉Pt/γ-Al2O3/CeO2〉Pt/γ-Al2O3/ZrO2.     

Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟

以CexZr1-xO2固溶体做载体, 制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂(x=1, 0.75, 0.5, 0.25, 0). 应用Brunauer-Emmet-Teller (BET)比表面积分析、X射线衍射(XRD)和H2程序升温还原(H2-TPR)等手段对催化剂进行相关表征, 并系统研究了催化剂在饮食油烟催化燃烧中的催化活性. BET结果表明催化剂的比表面积随Ce/Zr摩尔比的减小而减小. XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上. H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好. 催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧, 降低了反应温度. 随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化, 催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2>Pt/γ-Al2O3/Ce0.25Zr0.75O2>Pt/γ-Al2O3/Ce0.75Zr0.25O2>Pt/γ-Al2O3/CeO2>Pt/γ-Al2O3/ZrO2.     

Effect of composite supports on the methanation activity of Co-Mo-based sulphur-resistant catalysts

The effects of composite supports of CeO2-Al2O3,MgO-Al2O3,TiO2-Al2O3 or ZrO2-Al2O3 on the methanation activity of supported Co-Mo-based sulphur-resistant catalysts were investigated.The catalysts were further characterized by nitrogen adsorption measurement,X-ray diffraction and X-ray photoelectron spectroscopy.The catalyst of 5%CoO-15%MoO3 supported on CeO2-Al2O3,MgO-Al2O3,TiO2-Al2O3 or ZrO2-Al2O3 composite oxides,respectively,showed different catalytic performances of syngas methanation in the presence of hydrogen sulphide as compared with that of the 5%CoO-15%MoO3/Al2O3 catalyst.The Co-Mo/CeO2-Al2O3 catalyst shows the highest methanation activity among the tested catalysts.The enhanced methanation activity may be attributed to the improvement of the dispersion of active metal species and the inhibition of the formation of S6+.     

Simultaneous removal of ethanol, acetaldehyde and nitrogen oxides over V-Pd/γ-Al_2O_3-TiO_2 catalyst

V-Pd/γ-Al2O3-TiO2 catalysts with different vanadium contents were prepared by a combined sol-gel and impregnation method. X-ray diffraction (XRD), N2 adsorption-desorption (BET), X-ray photoelectron spectroscopy (XPS) and catalytic removal of ethanol, acetaldehyde and nitrogen oxides at low temperature (<300 ?C) were used to assess the properties of the catalysts. The results showed that the sample with 1wt% vanadium exhibited an excellent catalytic performance for simultaneous removal of ethanol, acetaldehyde and nitrogen oxides. The conversions of ethanol, acetaldehyde and nitrogen oxides at 250 ?C were 100%, 74.4% and 98.7%, respectively. V-Pd/γ-Al2O3-TiO2 catalyst with 1 wt% vanadium showed the largest surface area and higher dispersion of vanadium oxide on the catalyst surface, and possessed a larger mole fraction of V4+ species and unique PdO species on the surface, which can be attributed to the strong synergistic effect among palladium, vanadium and the carriers. The higher activity of V-Pd/γ-Al2O3-TiO2 catalyst is related to the V4+ and Pd2+ species on the surface, which might be favorable for the formation of active sites.     

Autothermal reforming of methane over Ni catalysts supported over ZrO2-CeO2-Al2O3

Ni catalysts supported on Al2O3, ZrO2-Al2O3, CeO2-Al2O3 and ZrO2-CeO2-Al2O3 were prepared by coprecipitation method, and their catalytic performances for autothermal reforming of methane to hydrogen were investigated. The Ni-supported catalysts were characterized by XRD, TPR and XPS. The relationship between the structures and catalytic activities of the catalysts was discussed. The results showed that the catalytic activity and stability of the Ni/ZrO2-CeO2-Al2O3 catalyst was better than those of other catalysts with the highest CH4 conversion, H2/CO and H2/COx ratio at 750 ℃. The catalyst showed a little deactivation along the reaction time during its 72 h on stream with the mean deactivation rate of 0.08%/h. The catalytic performance of the Ni/ZrO2-CeO2-Al2O3 catalyst was also affected by reaction temperature, no2 ： nCH4 molar ratio and nH2O ： nCH4 molar ratio. TPR, XRD and XPS measurements indicated that the formation of ZrO2-CeO2 solid solution could improve the dispersion of NiO, and inhibit the formation of NiAl2O3, and thus significantly promoted the catalytic activity of the Ni/ZrO2-CeO2-Al2O3 catalyst.     

Effect of Transition Metals (Cu, Co and Fe) on the Autothermal Reforming of Methane over Ni/Ce0.2Zr0.1Al0.7Oδ Catalyst

The transition metals (Cu, Co, and Fe) were applied to modify Ni/Ce0.2Zr0.1 Al0.7Oδcatalyst. The effects of transition metals on the catalytic properties of Ni/Ce0.2Zr0.1 Al0.7Oδautothermal reforming of methane were investigated. The Ni-supported catalysts were characterized by XRD, TPR and XPS. Tests in autothermal reforming of methane to hydrogen showed that the addition of transition metals (Cu and Co) significantly increased the activity of catalyst under the conditions of lower reaction temperature, and Ni/Cu0.05Ce0.2Zr0.1Al0.65Oδwas found to have the highest conversion of CH4 among all catalysts in the operation temperatures ranging from 923 K to 1023 K. TPR, XRD and XPS measurements indicated that the cubic phases of CexZr1-xO2 solid solution were formed in the preparation process of catalysts. Strong interaction was found to exist between NiO and CexZr1-xO2 solid solution. The addition of Cu improved the dispersion of NiO, inhibited the formation of NiAl2O4, and thus significantly promoted the activity of the catalyst Ni/Cu0.05Ce0.2Zr0.1Al0.65Oδ.     

Preparation and Characterization of Modified-ZrO2 Catalysts for the Reaction of Co Hydrogenation

ZrO2 in different structures and CexZr4-xO8 solid solutions have been prepared by a sol-gel related method with propionic acid as the solvent.The results of their characterization and CO hydrogenation performance eveluation show that ｔ-ZrO2 has better catalytic performance for CO hydrogenation to hydrocarbon than ｍ-ZrO2.Cerium(Ⅲ）acetate and zirconium (Ⅵ）acetylacetonate have been chosen as the most suitable starting materials for CexZr4-xO8 solid solution preparation.Ce-Zr reducibility properties are increased by the incorporation of zirconium oxide in the ceria structure.Ce2Zr2O8 exhibits a higher activity,lower methane selectivity and higher iso-C4 selectivity than tetragonal ZrO2.This implies that the formation mechanism of C4 hydrocarbons,especially that for the iso-C4 fraction is different over Ce2Zr2O8 and t-ZrO2.     

Autothermal Reforming of Methane over Ni Catalysts Supported on CuO-ZrO2-CeO2-Al2O3

Ni catalysts supported on various mixed oxides of Al2O3 with rare earth oxide and transitional metal oxides were synthesized. The studies focused on the measurement of the autothermal reforming of methane to hydrogen over Ni catalysts supported on the mixed oxide ZrxCe30-xAl70Oδ (x=5, 10, 15). The catalytic performance of Ni/Zr10Ce20Al70Oδ was better than that of other catalysts. XRD results showed that the addition of Zr to Ni/Ce30Al70Oδ prevented the formation of NiAl2O4 and facilitated the dispersion of NiO. Effects of CuO addition to Zr10Ce20Al70Oδ were also investigated. The activity of Ni catalyst supported on CuO-ZrO2-CeO2-Al2O3 was somewhat affected and the Ni/Cu5Zr10Ce20Al65Oδ showed the best catalytic performance with the highest CH4 conversion, yield of H2, selectivity for H2 and H2/CO production ratio in operation temperatures ranging from 650 to 750℃.     

Additive effects of alkaline-earth metals and nickel on the performance of Co/γ-Al_2O_3 in methane catalytic partial oxidation

Nano-sized γ-alumina (γ-Al2O3) was first prepared by a precipitation method. Then, active component of cobalt and a series of alkaline- earth metal promoters or nickel (Ni) with different contents were loaded on the γ-Al2O3 support. The catalysts were characterized by N2 adsorption-desorption, X-ray diffraction (XRD) and thermogravimetry analysis (TGA). The activity and selectivity of the catalysts in catalytic partial oxidation (CPO) of methane have been compared with Co/γ-Al2O3, and it is found that the catalytic activity, selectivity, and stability are enhanced by the addition of alkaline-earth metals and nickel. The optimal loadings of strontium (Sr) and Ni were 6 and 4 wt%, respectively. This finding will be helpful in designing the trimetallic Co-Ni-Sr/γ-Al2O3 catalysts with high performance in CPO of methane.     

铂基催化剂用于柴油烃氧化

The catalytic performance of Pt-based catalysts for the total oxidation of hydrocarbons was investigated.The activity of supported Pt catalysts(Pt/Al2O3,Pt/ZrO2,Pt/TiO2,and Pt/H-ZSM-5)depends on the metal oxide support.Pt/Al2O3 showed the highest catalytic activity when the catalysts were aged at 750°C for 50 h in air.The activity of Pt/Al2O3 was dependent on the valence state of the Pt surface.Pt/Al2O3 with the Pt surface in the metallic state was more active than with the surface in the cationic state.The surface density of acid and basic sites on the Al2O3 support controlled the valence state of the Pt surface and stability of the Pt particles in the highly dispersed state,respectively.     

Catalytic Combustion of Methane over MnOx／ZrO2-Al2O3 Catalysts

MnOx/Al2O3 and MnOx/ZrO2-Al2O3 catalysts were prepared by incipient wetness impregnation of Mn(CH3COO)2 on the corresponding supports, followed by the characterization using X-ray diffraction (XRD). temperature programmed reduction (TPR) and BET surface area techniques. The result shows the BET surface area of ZrO2-Al2O3 is lower than that of Al2O3 due to the loading of ZrO2.However tile resulted MnOx/ZrO2-Al2O3 catalyst exhibits higher activity for methane combustion than MnOx/Al2O3, because the addition of ZrO2 onto Al2O3 is beneficial for the dispersion of Mn species and the improvement of the lattice oxygen activity in MnOx. subsequently the activation of methane during combustion. The optimum loading of Zr in MnOx/ZrO2-Al2O3 is in the range of 5%-10% correlated with the calcination temperatures of catalyst supports.     

Surface Acidity/Basicity and Catalytic Reactivity of CeO2/7-Al2O3 Catalysts for the Oxidative Dehydrogenation of Ethane with Carbon Dioxide to Ethylene

Dehydrogenation of ethane to ethylene in CO2 was investigated over CeO2/γ-Al2O3 catalysts at 700℃ in a conventional flow reactor operating at atmospheric pressure. XRD, BET and microcalori-metric adsorption techniques were used to characterize the structure and surface acidity/basicity of the CeO2/γ-Al2O3 catalysts. The results show that the surface acidity decreased while the surface basicity increased after the addition of CeO2 to γ-A12O3. Accordingly, the activity of the hydrogenation reaction of CO2 increased, which might be responsible for the enhanced conversion in the dehydrogenation of ethane to ethylene. The highest ethane conversion obtained was about 15% for the 25%CeO2/γ-Al2O3. The selectivity to ethylene was high for all the CeO2,γ-A12O3 and CeO2/γ-Al2O3 catalysts.     

CO Selective Oxidation in Hydrogen-Rich Gas over Copper-Series Catalysts

The performances of CO selective oxidation in hydrogen-rich gas over four catalytic systems of CuO/ZrO2, CuO/MnO2, CuO/CoO and CuO/CeO2 were compared. The reducibility of these catalysts and the effect of CuO and CeO2 molar ratio of CuO/CeO2 catalysts on the activity of selective CO oxidation are investigated by XRD and TPR methods. The results show that the catalysts with the exception of CuO/ZrO2 have the interactions between CuO and CoO, CeO2 or MnO2, which result in a decrease in the reduction temperature. Among the catalysts studied, CuO/ZrO2 catalyst shows the lowest catalytic activity while CuO/CeO2 catalyst exhibits the best catalytic performance. The CuO(10%)/CeO2 catalyst attains the highest CO conversion and selectivity at 140 and 160℃. The addition of 9% H2O in the reactant feed decreases the activity of CuO/CeO2 catalyst but increases its CO selectivity.     

Effect of Ni Loading and CexZr1-xO2 Promoter on Ni-Based SBA-15 Catalysts for Steam Reforming of Methane

A series of Ni/SBA-15 catalysts with Ni contents ranging from 5wt% to 20wt% as well as 10wt%Ni/10wt?xZn-xO2/SBA-15 (z=0, 0.5, 1) were prepared. The structures of the catalysts were characterized using XRD, TPR, TEM and BET techniques. The catalytic activities of the catalysts for steam reforming of methane were evaluated in a continuous flow microreactor. The results indicated that both the Ni/SBA-15 and the Ni/CexZr1-xO2/SBA-15 catalysts had good catalytic activities at atmospheric pressure. The 10wt%Ni/SBA-15 catalyst exhibited excellent stability at 800癈 for time on stream of 740 h. After the reaction, carbon deposits were not formed on the surface of the catalyst. There existed a regular hexagonal mesoporous structure in the Ni/SBA-15 and the Ni/CexZr1-xO2/SBA-15 catalysts. The nickel species and the CexZr1-xO2 component were all confined in the SBA-15 mesopores. The CexZr1-xO2 could promote dispersion of the nickel species in the Ni/CexZr1-xO2/SBA-15 catalysts.     

Surface Acidity／Basicity and Catalytic Reactivity of CeO2／γ—A12O3 Catalysts for the Oxidative Dehydrogenation of Ethane with Carbon Dioxide to Ethylene

Dehydrogenation of ethane to ethylene in CO2 was investigated over CeO2/γ-Al2O3 catalysts at 700℃ in a conventional flow reactor operating at atmospheric pressure. XRD, BET and microcalorimetric adsorption techniques were used to characterize the structure and surface acidity/basicity of the CeO2/γ-Al2O3 catalysts. The results show that the surface acidity decreased while the surface basicity increased after the addition of CeO2 to γ-Al2O3. Accordingly, the activity of the hydrogenation reaction of CO2 increased, which might be responsible for the enhanced conversion in the dehydrogenation of ethane to ethylene. The highest ethane conversion obtained was about 15% for the 25?O2/γ-Al2O3. The selectivity to ethylene was high for all the CeO2, γ-Al2O3 and CeO2/γ-Al2O3 catalysts.     

Study of The Pd-B/ γ-Al2O3 Amorphous Alloy Catalyst

The Pd-B/γ-Al2O3 amorphous alloy catalyst and Pd/γ-Al2O3 crystalline metal catalyst were prepared by KBH4 reduction and routine impregnation,respectively.Pd-B/γ-Al2O3 and Pd/γ-Al2O3 catalysts were characterized by XRD and SEM.It was found that the catalytic activity of the Pd-B/γ-Al2O3 amorphous alloy catalyst was higher than that of the Pd/γ-Al2O3 crystalline metal catalyst in the anthraquinone hydrogenation.     

Comparing the deactivation behaviour of Co/CNT and Co/γ-Al2O3 nano catalysts in Fischer-Tropsch synthesis

An extensive study of Fischer-Tropsch (FT) synthesis on cobalt nano particles supported on γ-alumina and carbon nanotubes (CNTs) catalysts is reported.20 wt% of cobalt is loaded on the supports by impregnation method.The deactivation of the two catalysts was studied at 220 C,2 MPa and 2.7 L/h feed flow rate using a fixed bed micro-reactor.The calcined fresh and used catalysts were characterized extensively and different sources of catalyst deactivation were identified.Formation of cobalt-support mixed oxides in the form of xCoO yAl2O3 and cobalt aluminates formation were the main sources of the Co/γ-Al2O3 catalyst deactivation.However sintering and cluster growth of cobalt nano particles are the main sources of the Co/CNTs catalyst deactivation.In the case of the Co/γ-Al2O3 catalyst,after 720 h on stream of continuous FT synthesis the average cobalt nano particles diameter increased from 15.9 to 18.4 nm,whereas,under the same reaction conditions the average cobalt nano particles diameter of the Co/CNTs increased from 11.2 to 17.8 nm.Although,the initial FT activity of the Co/CNTs was 26% higher than that of the Co/γ-Al2O3,the FT activity over the Co/CNTs after 720 h on stream decreased by 49% and that over the Co/γ-Al2O3 by 32%.For the Co/γ-Al2O3 catalyst 6.7% of total activity loss and for the Co/CNTs catalyst 11.6% of total activity loss cannot be recovered after regeneration of the catalyst at the same conditions of the first regeneration step.It is concluded that using CNTs as cobalt catalyst support is beneficial in carbon utilization as compared to γ-Al2O3 support,but the Co/CNTs catalyst is more susceptible for deactivation.     

Catalytic Combustion of Methane over CO1-xMgxO/Al2O3/FeCrAl Monolithic Catalysts

A series of CoxMgxO/Al2O3/FeCrAl catalysts （x=0-1） were prepared. The structures of the catalysts were characterized using XRD, SEM, and TPR analyses. The catalytic activity of the catalysts for methane combustion was evaluated in a continuous flow microreactor. The results indicated that the active washcoats adhered well on the FeCrAl foils. The phases in the catalysts were Co--xMgxO solid solutions, α-Al2O3, and γ-Al2O3. The surface particle size of the catalysts varied with variations in the molar ratios of Co to Mg. The Co component of the Co1_xMgxO/Al2O3/FeCrAl catalysts played an important role in the catalytic activity for methane combustion. In the Co1-xMgxO/AluO3/FeCrAl series catalyst （x=0.2-0.8）, the catalytic activity in terms of x was in the order of 0.5〉0.2〉0.8 under the experimental conditions. The presence of Mg in these catalysts could promote the thermal stability to a large extent. There were strong interactions between the Co1-xMgxO oxides and the AluO3/FeCrAl supports.     

Catalytic activity and crystal structure modification of Pd/γ-Al_2O_3–TiO_2 catalysts with different Al_2O_3 contents

Pd/γ-Al_2O_3–TiO_2 catalysts containing various compositions of titania and alumina were prepared by sol–gel and wet-impregnation methods in attempt to study the particle size, nature of phases, morphology and structure of the composite samples. The ethanol oxidation experiments, N_2 adsorption–desorption,FTIR, XRD and XPS were conducted, and the effects of Al_2O_3 content on the surface area, phase transformation and structural properties of TiO_2 were investigated. The optimal value of ethanol conversion appeared on Pd/Al(0.05)–Ti and Pd/Al(0.90)–Ti catalysts irrespective of the ethanol oxidation temperature, and we call this as a double peaks phenomenon of catalytic activity. The XRD results reveal that the phase composition and crystallite size of the mixed oxides depend on Al_2O_3/TiO_2 ratio and calcination temperature. Al_2O_3 can effectively prevent the agglomeration of TiO_2 and this can be ascribed to the formation of Al–O–Ti chemical bonds in Al_2O_3–TiO_2 crystals. Binding energy and Pd surface concentration of the catalysts were modified apparently, which may also lead to catalyst activity changes.