A new design and coatings for piezoelectric crystals in measurement of trace amounts of sulfur dioxide

A new design for the coated piezoelectric crystal detector cell is described; this provides very high sensitivity. Triethanolamine and quadrol are the new substrates used for the detection of sulfur dioxide. The new design and the new coatings together make possible the selective detection of sulfur dioxide in nitrogen even at p.p.b. levels.     

A new calibration method for the determination of trace amounts of mercury in air and biological materials

Summary A new calibration method for the determination of mercury by CVAAS using collector preconcentration is described. The main piece of a developed calibration device is a special valve which links a closed Hg — saturated gas flow with an open flow of the carrier gas to the AA — spectrometer. This principle allows the direct injection of defined Hg-saturated gas volumes into the sample gas-flow. In this way the known systematic errors of traditional methods by contamination and loss, caused above all by the manual handling of mercury vapor or solution, are avoided. Instrumental and procedural aspects of the application are discussed and the reliability relating to the mercury determination in air and biological materials is evaluated. The new method is superior to the other calibration methods in every way. In the 1 ng Hg range the within-run precision is better than 1%, and the day-to-day precision better than 2%. The accuracy was validated by determining various biological SRMs. All the results in the g/g and ng/g level corresponded well to certified values. The new method is also a simple and reliable way of carrying out the necessary internal quality control.     

Sensitive detection of trace hemoglobin using fluorescence method based on functionalized quantum dots

The fluorescence quenching of quantum dots by hemoglobin has been demonstrated to depend on surface functionalization, and this property has been utilized to construct a novel fluorescent method for rapid, sensitive, and selective detection of trace hemoglobin in urine at microgram level. This method shows low interference and high selectivity for hemoglobin with a limit of detection of 4.3 μg L^?1 in water and 66.1 μg L^?1 in urine, which are lower than those of currently used methods in labs and clinics. Spike and recovery tests in raw, acidified, and alkalized urine samples exhibit good recovery rates for the spiked concentrations close to the limit of detection.

Determination of trace amounts of bromide by flow injection/stopped-flow detection technique using kinetic-spectrophotometric method

A simple, sensitive and selective method for the determination of bromide in seawater by using a flow injection/stopped-flow detection technique was examined. The detection system was developed for a new kinetic-spectrophotometric determination of bromide in the presence of chloride matrix without any extraction and/or separation. The detection was based on the kinetic effect of bromide on the oxidation of methylene blue (MB) with hydrogen peroxide in a strongly acidic solution. Large amounts of chloride could enhance the sensitivity of the method as an activator. The decolorisation of the blue color of MB was used for the spectrophotometric determination of bromide at 746 nm. A stopped-flow approach was used to improve the sensitivity of the measurement and provide good linearity of the calibration over the range of 0-3.2 μg ml⁻¹ of bromide. The relative standard deviation was 0.74% for the determination of 2.4 μg ml⁻¹ bromide (n = 5). The detection limit (3σ) was 0.1 μg ml⁻¹ with a sampling frequency of 12 h⁻¹. The influence of potential interfering ions was studied. The proposed method was applied to the determination of bromide in seawater samples and provided satisfactory results.     

A sensitive flow-injection method for determination of trace amounts of nitrite

A new sensitive colour reaction for nitrite determination is presented. In acidic medium, nitrite was reacted with safranine to form a diazonium salt which caused the reddish-orange dye colour of the solution to change to blue. The carrier stream, into which the sample solution was injected, was doubly distilled water. The reagent solution stream, which contained safranine dye, hydrochloric acid and potassium chloride, was mixed with the carrier in a 3-m length of silicon tubing (bore 0.5 mm) maintained at 30°C in a thermostatic bath. The absorbance intensity was measured at 520 nm. The detection limit was 20 ng ml⁻¹ and the RSD% of 20 injections of 1 μg ml⁻¹ of nitrite was 0.65%. Analysis can be done at a rate of up to 30 h⁻¹. Under the optimum conditions in the concentration range of 30–4000 ng ml⁻¹ of nitrite ion, a linear calibration graph was obtained (r=0.9999). The method was applied successfully to the determination of nitrite in sausages.     

Sensitive spectrophotometric method for trace amounts of uranium

A sensitive spectrophotometric method for the determination of uranium with Pyrogallol Red (PGR) and cetyltrimethylammonium bromide (CTAB) is described. The sensitivity of the colour reaction between uranium and Pyrogallol Red is greatly increased in the presence of cetyltrimethylammonium bromide. The blue ternary complex (λ_max580 nm) has composition 1:2:4 [U(VI):PGR:CTAB] at pH 5.6. Beer's law is obeyed over the range 19.0-0.24 ppm of uranium and the molar absorptivity is 3.3 × 10⁴ l.mole⁻¹.cm⁻¹ at 620 nm. A tentative structure for the ternary complex is suggested. A simple method is suggested for evaluation of stability constants of such ternary complexes.     

Enrichment method for trace amounts of rare earth elements using chemofiltration and XRF determination

A preconcentration method for subsequent determination of rare earth elements (REE) by X-ray fluorescence (XRF) spectrometry was developed. The method is based on using (o-[3,6-disulfo-2-hydroxy-1-naphthylazo]-benzenearsonic acid) (Thorin) as a complexing agent which is retained on a polyamide membrane by a chemofiltration process. The pH dependence of the chemofiltration of these metal ions on the membrane and other variables, such as flow-rate, contact time, kinetic of complex formation, etc. were determined. The membrane containing the chemofiltrate formed a thin film, which eliminated the interelemental effects when measured by XRF. The detection limits were 23, 23 and 49 ng/mL for Sm(III), Eu(III) and Gd(III), respectively. High enrichment factors were obtained. The method was successfully applied to the preconcentration of Sm(III), Eu(III) and Gd(III) from different samples. Received: 8 March 2000 / Revised: 9 May 2000 / Accepted: 15 May 2000     

Enrichment method for trace amounts of rare earth elements using chemofiltration and XRF determination

A preconcentration method for subsequent determination of rare earth elements (REE) by X-ray fluorescence (XRF) spectrometry was developed. The method is based on using (o-[3,6-disulfo-2-hydroxy-1-naphthylazo]-benzenearsonic acid) (Thorin) as a complexing agent which is retained on a polyamide membrane by a chemofiltration process. The pH dependence of the chemofiltration of these metal ions on the membrane and other variables, such as flow-rate, contact time, kinetic of complex formation, etc. were determined. The membrane containing the chemofiltrate formed a thin film, which eliminated the interelemental effects when measured by XRF. The detection limits were 23, 23 and 49 ng/mL for Sm(III), Eu(III) and Gd(III), respectively. High enrichment factors were obtained. The method was successfully applied to the preconcentration of Sm(III), Eu(III) and Gd(III) from different samples. Received: 8 March 2000 / Revised: 9 May 2000 / Accepted: 15 May 2000     

A new resonance scattering spectral method for the determination of trace amounts of iodate with rhodamine 6G

Under the conditions of 0.04 mol L⁻¹ HCl-8.0 × 10⁻⁴ mol L⁻¹ KI, there is a fluorescence peak at 540 nm and a synchronous fluorescence peak at 540 nm for rhodamine 6G (RhG). When there is IO₃⁻, it reacts with exceed I⁻ to form I₃⁻. And I₃⁻ and RhG combine into ion association particles. The particles exhibit three resonance scattering peaks at 320, 400 and 595 nm. And there is fluorescence quenching at 540 nm. Iodine concentration is proportional to the intensity of the resonance scattering intensity at 400 nm in the range of 1.0-20 × 10⁻⁷ mol L⁻¹. And a new resonance scattering spectral (RSS) method has been described for the determination of IO₃⁻ in salt samples. The spectral results have been verified that the formation of (RhG-I₃)_n association particles and solid-liquid interfaces are the main factor that cause the fluorescence quenching and resonance scattering effects.     

A new method for atmospheric nitrogen dioxide measurements using the combination of a stripping coil and fluorescence detection.

A new stripping coil for the collection of nitrogen dioxide (NO2) has been developed to increase its versatility and efficiency. Nitrogen dioxide measurements based on quantitative collection through a reaction coil into an alkaline solution has been examined. Nitrogen dioxide is collected in a 0.1 N NaOH solution. This collection system has an efficiency of nearly 100%. The absorbed nitrogen dioxide has been measured by fluorescence detection with sub-ppbv detection limits. The excitation wavelength at 360 nm and the produced emission wavelength at 405 nm were suitable for nitrite ion measurements.     

A chemical enhancement method for the spectrophotometric determination of trace amounts of arsenic

A highly sensitive spectrophotometric method for the determination of 0.03-1.0 microg of arsenic is described. After extraction as AsI(3) into benzene, it is selectively stripped into water. Both the arsenic(III) and iodide present in the aqueous phase are made to react with iodate in acidic medium in the presence of chloride to form the anionic chloro complex, ICl(-)(2). The determination is completed after extraction of ICl(-)(2) species as an ion-pair with Rhodamine 6G into benzene and measuring the absorption of the extract at 535 nm. The coefficient of variation is 1.5% for 10 determinations of 0.5 microg of arsenic. The method has been applied to the determination of arsenic content in plant materials, high purity iron, copper base alloys and inorganic arsenic levels of natural waters.     

荧光猝灭法测定痕量NO2-

在HCl介质中,NO2-与5-氨基-1,2,3,4-四氢-1,4酞嗪二酮(ATPD)发生亚硝化反应,使ATPD的荧光猝灭,且其荧光猝灭程度与NO2-量呈线性关系,从而建立了测定痕量NO2-的新方法。该法线性范围为0.067~1.172μg/mL,方法检出限为0.70μg/L。本法已用于雨水中痕量NO2-的测定。     

A new method for using 18O to trace ozone deposition

Isotopically labelled ozone (¹⁸O₃) is an ideal tool to study the deposition of O₃ to plants and soil, but no studies have made use of it due to the technical difficulties in producing isotopically enriched ozone. For ¹⁸O₃ to be used in fumigation experiments, it has to be purified and stored safely prior to fumigations, to ensure that the label is present predominantly in the form of O₃, and to make efficient use of isotopically highly enriched oxygen. We present a simple apparatus that allows for the safe generation, purification, storage, and release of ¹⁸O₃. Following the purification and release of O₃, about half (by volume) of the ¹⁸O is present in the form of O₃. This means that for a given release of ¹⁸O₃ into the fumigation system, a roughly identical volume of ¹⁸O₂ is released. However, the small volume of this concurrent ¹⁸O₂ release (100 nmol mol^?1 in our experiment) results in only a minor shift of the much larger atmospheric oxygen pool, with no detectable consequence for the isotopic enrichment of either soil or plant materials. We demonstrate here the feasibility of using ¹⁸O as an isotopic tracer in O₃ fumigations by exposing dry soil to 100 nmol mol^{?1 18}O₃ for periods ranging from 1 to 11 h. The ¹⁸O tracer accumulation in soil samples is measured using gas chromatography/isotope ratio mass spectrometry (GC/IRMS), and the results show a linear increase in ¹⁸O/¹⁶O isotope ratio over time, with significant differences detectable after 1 h of exposure. The apparatus is adapted for use with fumigation chambers sustaining flow rates of 1 m³ min^?1 for up to 12 h, but simple modifications now allow larger quantities of O₃ to be stored and continuously released (e.g. for use with open‐top chambers or FACE facilities). Copyright © 2009 John Wiley & Sons, Ltd.     

A new catalytic polarographic system for determination of trace amounts of tungsten

A new catalytic polarographic system for the determination of trace amounts of tungsten is described. It is found that the tungsten-2-mercaptobenzothiazole (MBT) complex yields a sensitive catalytic hydrogen wave at -1.10 V (vs. SCE) in strongly acidic medium. The peak height is a linear function of tungsten concentration over the range 0.004-1.4 mug/ml in 0.9M H(2)SO(4)-20 mg/ml NaCl-0.01 mug/ml MBT medium. The method can be applied for determination of trace amounts of tungsten in geochemical materials.     

A new HPLC method with fluorescence detection for the determination of memantine in human plasma

A sensitive, selective, simple and fast HPLC method based on the formation of derivative with fluorescamine was developed for the determination of memantine (ME) in human plasma. Separation was achieved on a CN column (200 mm×4.6 mm) using acetonitrile-10 mM orthophosphoric acid containing 1 mL/L triethylamine (45:55, v/v) at a flow rate of 1 mL/min. Emission and excitation wavelengths were 480 and 380 nm, respectively. Amantadine was used as an internal standard. Calibration graphs were rectilinear over the range of 1.0-100.0 ng/mL. Limit of detection and limit of quantification were found to be 0.3 and 1.0 ng/mL, respectively. Intra-day and inter-day relative standard deviation values were found to be <2.03%. Average recovery was also found to be around 94%. Proposed method was applied for the pharmacokinetic study in a healthy volunteer after a single oral administration of 20 mg of ME.     

A new and simple method to determine trace levels of sulfonamides in honey by high performance liquid chromatography with fluorescence detection

A novel method for the simultaneous analysis at trace level of sulfonamides (sulfaguanidine, sulfanilamide, sulfacetamide, sulfathiazole, sulfapyridine, sulfachloropyridazine, sulfamerazine, sulfameter, sulfamethazine, sulfadoxine, sulfadiazine, sulfamonomethoxine, sulfadimethoxine) in honey is described. Methanol has been used in the sample treatment step to avoid the emulsion formation and to break the N-glycosidic bond between sugars and sulfonamides. The determination is carried out by liquid chromatography in gradient elution mode, with fluorescence detection after the on-line pre-column derivatization with fluorescamine. The influence of parameters such as the mobile phase composition, column temperature, pH or injection volume, on the separation has been taken into account and the derivatization step has also been optimized. Recoveries of the compounds on spiked honey samples ranged from 56% for sulfadoxine to 96% for sulfacetamide, with relative standard deviations below 10%. The quantitation limits are between 4 and 15 ng g⁻¹.     

Kinetic-spectrophotometric method for the determination of trace amounts of bromide in seawater

A novel simple, sensitive and rapid kinetic-spectrophotometric method is proposed for the determination of trace amounts of bromide. The method is based on its catalytic effect on the oxidation of methylene blue (MB) by hydrogen peroxide in strongly acidic solution. The oxidation reaction is activated by large amounts of chloride and can be monitored spectrophotometrically by measuring the decrease in the absorbance of MB at 746 nm. The determination of bromide is performed by a fixed-time method at the first 100 s from the initiation of the reaction. Unlike other kinetic-spectrophotometric methods for the determination of bromide, the proposed method does not require heating the solution. Bromide can be determined in the range from 80 to 960 μg l⁻¹ with the detection limit of 35 μg l⁻¹. The relative standard deviation of ten replicate determination of 480 μg l⁻¹ bromide was 1.4%. The influence of potential interfering ions was studied. The proposed method was satisfactorily applied to the determination of bromide in seawater without interfering effect from chloride ion.     

A sensitive and selective detection method for thiol compounds using novel fluorescence probe

In this work, a sensitive and selective detection method based on fluorescence resonance energy transfer (FRET) was developed for analyzing thiol compounds by using a novel fluorescent probe. The new fluorescent probe contains a disulfide bond which selectively reacts with nucleophilic thiolate through the thiol-disulfide exchange reaction. An obvious fluorescence recovery can be observed upon addition of the thiol compound in the fluorescent probe solution due to the thiol-disulfide exchange reaction and the destruction of FRET. This novel probe was successfully used to determine dithiothreitol (DTT), glutathione (GSH) and cysteine (Cys). The limits of detection (LOD) were 2.0 μM for DTT, 0.6 μM for GSH, and 0.8 μM for Cys. This new detection method was further investigated in the analysis of compound amino acid injection.     

A sensitive spectrophotometric method for the determination of trace amounts of uranium (VI) using o-hydroxypropiophenone isonicotinoyl hydrazone

The reaction between uranium (VI) and o-hydroxypropiophenone isonicotinoyl hydrazone (OHPINH) has been investigated in HCl-sodium acetate buffers and a highly sensitive and simple procedure for the determination of uranium (VI) is suggested. The yellow colored complex showed maximum absorption at 380 nm in buffer solutions of pH 3. Beer's law is obeyed in the range of 0.47–17 g ml^–1. The molar absorptivity and Sandell sensitivity are found to be 1.15×10⁴ dm³ mol^–1 cm^–1 and 0.02 g cm^–2, respectively. The composition of the complex is found to be 11 between metal and reagent.     

茶叶中的茶多酚荧光检测方法

以石墨烯量子点为荧光探针,基于二氧化锰纳米片与石墨烯量子点之间发生有效的荧光共振能量转移,构建了一种茶叶中茶多酚含量的荧光检测新方法。MnO2纳米片使石墨烯量子点的荧光淬灭,而茶多酚能与MnO2发生氧化还原反应,将其还原成Mn^2+,使体系荧光恢复。茶多酚含量与荧光强度增量在20~750μg/mL范围内成线性相关,线性方程为F=1.0574c-114.9,线性相关系数为R=0.9936。将该方法用于茶叶中茶多酚含量的检测,结果与国标法接近。方法有望应用于食品中其它抗氧化物质的实时检测。