Hydrophilic segmented block copolymers based on poly(ethylene oxide) and monodisperse amide segments

Segmented block copolymers based on poly(ethylene oxide) (PEO) flexible segments and monodisperse crystallizable bisester tetra‐amide segments were made via a polycondensation reaction. The molecular weight of the PEO segments varied from 600 to 4600 g/mol and a bisester tetra‐amide segment (T6T6T) based on dimethyl terephthalate (T) and hexamethylenediamine (6) was used. The resulting copolymers were melt‐processable and transparent. The crystallinity of the copolymers was investigated by differential scanning calorimetry (DSC) and Fourier Transform infrared (FTIR). The thermal properties were studied by DSC, temperature modulated synchrotron small angle X‐ray scattering (SAXS), and dynamic mechanical analysis (DMA). The elastic properties were evaluated by compression set (CS) test. The crystallinity of the T6T6T segments in the copolymers was high (>84%) and the crystallization fast due to the use of monodisperse tetra‐amide segments. DMA experiments showed that the materials had a low T_g, a broad and almost temperature independent rubbery plateau and a sharp flow temperature. With increasing PEO length both the PEO melting temperature and the PEO crystallinity increased. When the PEO segment length was longer than 2000 g/mol the PEO melting temperature was above room temperature and this resulted in a higher modulus and in higher compression set values at room temperature. The properties of PEO‐T6T6T copolymers were compared with similar poly(propylene oxide) and poly(tetramethylene oxide) copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4522–4535, 2007     

DSC studies of solid polymeric electrolytes

Relations are demonstrated between the conductivity, phase structure and thermal history of some solid polymeric electrolytes. The results obtained for systems based on commercially available polymers, e.g. (ethylene oxide), and for specially synthesized materials are presented. Special emphasis is placed on the correlation between the crystallinity, glass transition temperature, melting temperature and conduction properties of the polymeric electrolytes.This work was supported financially by the Rector of Warsaw University of Technology according to research program 503/164/220/1.     

Solid polymer electrolytes I,preparation, characterization,and ionic conductivity of gelled polymer electrolytes based on novel crosslinked siloxane/poly(ethylene glycol) polymers

A series of crosslinked siloxane/poly(ethylene glycol) (Si–PEG) copolymers were synthesized from the reactive methoxy‐functional silicone resin (Si resin) and PEGs with different molecular weights via two kinds of crosslinking reactions during an in situ curing stage. One of the crosslinking reactions is the self‐condensation between two methoxy groups in the Si resin, and another one is an alkoxy‐exchange reaction between the methoxy group in the Si resin and the OH group in PEG. The synthesized crosslinked copolymers were characterized by Fourier transform infrared spectroscopy, DSC, and ¹³C NMR. The crosslinked copolymers were stable in a moisture‐free environment, but the Si? O? C linkages were hydrolyzed in humid conditions. The gel‐like solid polymer electrolytes (SPEs) were prepared by impregnating these crosslinked Si–PEG copolymers in a propylene carbonate (LiClO₄/PC) solution. The highest conductivity reached 2.4 × 10^?4 S cm^?1 at 25 °C and increased to 8.7 × 10^?4 S cm^?1 at 85 °C. The conductivities of these gel‐type SPEs were affected by the content of LiClO₄/PC, the molecular weights of PEGs, and the weight fraction of the Si resin. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2051–2059, 2004     

Poly(ethylene oxide)/poly(2vinylpyridne)/lithium perchlorate blends as solid polymer electrolytes: Composition/property/structure interrelationship

Poly(ethylene oxide) (MW 600,000)/poly(2vinylpyridine) (MW 200,000)/LiClO₄ blends have been prepared by the solution blending process. The ionic conductivities of the blends containing lower weight fractions (15, 17.5, 20 and 22.5%) of poly (2vinylpyridine) initially increases as the salt content is increased, reaches a maximum at an ethylene oxide/Li⁺ mole ratio of 10 and decreases as the salt content is further increased. Blends, which have higher weight fractions of poly(2vinylpyridine) (25 and 35%) display different electric behavior, i.e., the ionic conductivity continously increased as the salt content is increased to an ethylene oxide/Li⁺ mole ratio of 2. Thermal, ⁷Li solidstate NMR and semiempirical MNDO molecular orbital studies indicate that this contrasting behavior may be explained by the structure and ratios of the solvates (mixed solvate or homosolvate) of LiClO₄ present in the blends. © 1995 John Wiley & Sons, Inc.     

Self-diffusion study of poly (ethylene oxide)-poly (propylene oxide)-poly (ethylene oxide) block copolymers in aqueous solution

The self-diffusion of poly (ethylene oxide)-poly (propylene oxide)-poly (ethylene oxide) block copolymers dissolved in deuterated water was investigated by means of pulsed field gradient NMR (PFG-NMR). The polymer forms micelles in the solution and, with increasing temperature, clouding and phase demixing occurs. The self-diffusion coefficient indicates the association of the polymer molecules in the vicinity of the cloud point because of its maximum with increasing temperature. Above the cloud point, two kinds of diffusing species are observed due to phase separation. The faster diffusing species is attributed to the polymer-poor phase. The self-diffusion coefficient of the polymer-rich phase species decreases with increasing temperature above the cloud point due to further association and dehydration. The correlation length of the diffusing associates, calculated from the self-diffusion coefficient and the viscosity by means of the Stokes-Einstein equation is nearly independent of temperature and concentration up to 30 wt-% polymer concentration. The correlation length is about 1.4 nm. It shows a slight maximum at the cloud point.     

Synthesis and characterization of poly(ethylene oxide)/polylactide/poly(ethylene oxide) triblock copolymer

Poly(ethylene oxide/polylactide/poly(ethylene oxide) (PEO/PL/PEO) triblock copolymers, in which each block is connected by an ester bond, were synthesized by a coupling reaction between PL and PEO. Hydroxyl‐terminated PLs with various molecular weights were synthesized and used as hard segments. Hydroxyl‐terminated PEOs were converted to the corresponding acid halides via their acid group and used as a soft segment. Triblock copolymers were identified by Fourier transform infrared spectroscopy, ¹H NMR, and gel permeation chromatography. Differential scanning calorimetry (DSC) and X‐ray diffractometry of PEO/PL/PEO triblock copolymers suggested that PL and PEO blocks were phase‐separated and that the crystallization behavior of the PL block was markedly affected by the presence of the PEO block. PEO/PL/PEO triblock copolymers with PEO 0.75k had two exothermic peaks (by DSC), and both peaks were related to the crystallization of PL. According to thermogravimetric analysis, PEO/PL/PEO triblock copolymer showed a higher thermal stability than PL or PEO. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2545–2555, 2002     

Effects of the conductivity of sulfonated poly(phenylene oxide) lithium by the complexation of poly(ethylene oxide)

In the present paper, the structure and conductivity for the complex of sulfonated poly(phenylene oxide) lithium (SPPOLi) and poly(ethylene oxide) (PEG) were studied. Glass transition temperature change determined by differential scanning calorimeter analysis desmonstrated that the two components had some compatibility. X-ray diffraction showed that PEG could decrease the regularity of SPPOLi to some extent. The compatibility and PEG's effect on the regularity may be due to the interaction between the lithium ions of SPPOLi and the oxygen atoms of PEG. Under polarization by electric field, the bands between lithium ions and sulfonation groups relaxed. Meanwhile, the complexation of oxygen atoms could enhance the dissociation of the polymeric lithium salts. Then lithium ions were transported in the process of alternate complexing and decomplexing. The action between lithium ions and oxygen atoms could explain the improvement on the conductivity of SPPOLi.     

Crosslinked poly(ethylene oxide) modified with tetraalkylammonium salts as phase transfer catalyst

Radiation crosslinked poly(ethylene oxide)s (PEO) modified with two tetraalkylammonium salts: allyldimethyldodecylammonium bromide and ethylmethacrylate dimethyldodecylammonium bromide were prepared. They have been characterized by elemental analysis, IR, ¹H-NMR spectra, and DSC measurements. Their activity as phase transfer catalysts (PTC) in the model displacement reaction of 1-bromooctane with aqueous sodium cyanide were studied. The reaction kinetics were followed under pseudo-first-order conditions. Small amounts of onium salt inserted into the PEO network gave rise to a five time increase in the rate constant. The recovered catalysts could be re-used without loss of activity. © 1995 John Wiley & Sons, Inc.     

Proton conducting membranes based on poly(vinyl chloride) graft copolymer electrolytes

The direct preparation of proton conducting poly(vinyl chloride) (PVC) graft copolymer electrolyte membranes using atom transfer radical polymerization (ATRP) is demonstrated. Here, direct initiation of the secondary chlorines of PVC facilitates grafting of a sulfonated monomer. A series of proton conducting graft copolymer electrolyte membranes, i.e. poly(vinyl chloride)‐g‐poly(styrene sulfonic acid) (PVC‐g‐PSSA) were prepared by ATRP using direct initiation of the secondary chlorines of PVC. The successful syntheses of graft copolymers were confirmed by ¹H‐NMR and FT‐IR spectroscopy. The images of transmission electron microscopy (TEM) presented the well‐defined microphase‐separated structure of the graft copolymer electrolyte membranes. All the properties of ion exchange capacity (IEC), water uptake, and proton conductivity for the membranes continuously increased with increasing PSSA contents. The characterization of the membranes by thermal gravimetric analysis (TGA) also demonstrated their high thermal stability up to 200°C. The membranes were further crosslinked using UV irradiation after converting chlorine atoms to azide groups, as revealed by FT‐IR spectroscopy. After crosslinking, water uptake significantly decreased from 207% to 84% and the tensile strength increased from 45.2 to 71.5 MPa with a marginal change of proton conductivity from 0.093 to 0.083 S cm^?1, which indicates that the crosslinked PVC‐g‐PSSA membranes are promising candidates for proton conducting materials for fuel cell applications. Copyright © 2008 John Wiley & Sons, Ltd.     

Phase behavior and Li+ Ion conductivity of styrene‐ethylene oxide multiblock copolymer electrolytes

Solid polymer electrolytes are attractive materials for use as battery separators. Here, a molecular weight series of polystyrene–polyethylene oxide (PEO) multiblock copolymers was synthesized by the thiol–norbornene click reaction. The subsequent materials were characterized both neat and with a lithium bis‐(trifluoromethane)sulfonimide salt loading [(Li)/(EO)] of 0.1. In general, neat samples demonstrated crystallinity scaling with PEO content. Lithium ion‐containing samples had broad scattering peaks, half of which displayed disordered scattering, even at the lowest block molecular weights (polystyrene = 1 kg/mol, PEO = 1 kg/mol). Fitting of disordered scattering data, using the random phase approximation, yielded χ_RPA and R_g values that were compared with recent predictive work by Balsara and coworkers. The predictions were accurate near the volume fraction f_PEO = 0.5 but deviated symmetrically with volume fraction asymmetry. Samples were also analyzed by electrochemical impedance spectroscopy for their potential to conduct lithium ions. Samples with f_PEO ≥ 0.5 demonstrated robust conductivity, whereas samples below this volume fraction conducted very poorly, with one exception (f_PEO = 0.24). This work expanded upon our recently reported approach to multiblock copolymer synthesis, demonstrating the improved access of materials to further our fundamental understanding of multiblock copolymers. Copyright © 2016 John Wiley & Sons, Ltd.     

Poly(ethylene oxide) electrolytes containing mixed salts

An unusual conductivity enhancement occurs in PEO-based ZnBr₂/LiBr electrolytes of composition, [xZnBr₂ + (1 ? x)LiBr](PEO)₁₆ with x = 0.00, 0.05, 0.50, 0.75, 1.00. The conductivity of the mixed-salt electrolytes is higher than that of either pure salt electrolyte. The highest conductivity, observed for x = 0.5, is two orders of magnitude higher than that of pure LiBr(PEO)₁₆ and one order higher than ZnBr₂(PEO)₁₆. In contrast, the conductivity of mixed Mg (CIO₄)₂/LiCIO₄ electrolytes, [xMg(CIO₄)₂ + (1 ? x) LiCIO₄](PEO)₁₆ where x = 0.00, 0.20, 0.50, 0.80, 1.00, increases monotonically with the mole fraction of the higher conductivity component, LiCIO₄(PEO)₁₆. The conductivity and differential scanning calorimetry (DSC) results suggest that the conductivity enhancement in the ZnBr₂/LiBr electrolytes results from a change in charge carrier type and concentration, whereas the conductivity change in the Mg(CIO₄)₂/LiCIO₄ electrolytes arises from a change in the microscopic viscosity of the electrolytes. © 1993 John Wiley & Sons, Inc.     

Single-ion and salt conductor polymer electrolytes based on poly(4-vinylpyridine) quaternized with poly(ethylene oxide) side chains

A new type of single-ion conductor with fixed cation was synthesized by spontaneous anionic polymerization of 4-vinylpyridine in the presence of short polyethylene oxide ( PEO ) chains as alkylating agents. These comblike polymers have low T_gs and are amorphous with the shorter PEO s. Their conductivities are unaffected by the nature of the anion ( Br ⁻, ClO ₄⁻, and tosylate) and are controlled by the free volume and the mobility of the pendant cation. By comparison of the results at constant free volume, it is shown that the charge density decreases with the increasing length of pendant PEO demonstrating that PEO acts only as a plasticizing agent. Best conductivity results (σ = 10⁻⁵ S cm⁻¹ at 60°C) are obtained with PEO side chains of molecular weight 350. With this sample, the conductivity in the presence of various amounts of added salt (LiTFSI) was studied. A best value of 10⁻⁴ S cm⁻¹ at 60°C is obtained with a molar ratio EO/Li of 10. It is shown that, over the range of examined concentrations (0.2–1.3 mol Li kg⁻¹), the reduced conductivity σ_r/c increases linearly with increasing salt concentration showing that the ion mobility increases continuously. Such behavior is quite unusual since in this concentration range a maximum is generally observed with PEO systems. To interpret this result and by analogy with the behavior of this type of polymer in solution, it is proposed that the conformation of these polymers in the solid state is segregated with the P4VP skeleton more or less confined inside the dense coils surrounded by the PEO side chains. Under the influence of the increasing salt concentration, this microphase separation vanishes progressively: The LiTFSI salt exchanges with the tosylate anions and acts as a miscibility improver agent. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2719–2728, 1997     

Comparison of Li+‐ion conductivity in linear and crosslinked poly(ethylene oxide)

Polymer electrolytes are of tremendous importance for applications in modern lithium‐ion (Li⁺‐ion) batteries due to their satisfactory ion conductivity, low toxicity, reduced flammability, as well as good mechanical and thermal stability. In this study, the Li⁺‐ion conductivity of well‐defined poly(ethylene oxide) (PEO) networks synthesized via copper(I)‐catalyzed azide–alkyne cycloaddition is investigated by electrochemical impedance spectroscopy after addition of different lithium salts. The ion conductivity of the network electrolytes increases with increasing molar mass of the PEO chains between the junction points which is completely opposite to the behavior of their respective uncrosslinked linear precursors. Obviously, this effect is directly related to the segmental mobility of the PEO chains. Furthermore, the ion conductivity of the network electrolytes under investigation increases also with increasing size of the anion of the added lithium salt due to a weaker anti‐plasticizing effect of the more bulky anions. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 21–28     

Poly(ethylene oxide)-polyurethane/poly(acrylonitrile) semi-interpenetrating polymer networks for solid polymer electrolytes: vibrational spectroscopic studies in support of electrical behavior

Studies on solid polymer electrolyte systems based on semi-interpenetrating polymer networks of poly(ethylene oxide)-polyurethane and poly(acrylonitrile) (PEO-PU/PAN) doped with lithium trifluoromethanesulfonate (LiCF₃SO₃) is reported. Room temperature FT-IR analysis indicates a salt solvation process that occurs predominantly in the polyether segments of the semi-IPNs and incorporation of salt is also seen to favor a morphological change in the matrix with a transition from semi-crystalline to amorphous phase. From the relative band areas a critical concentration (C_c) of salt can be identified where concentration of ionic species, morphology and amount of transient crosslinks is optimal to impart maximum conductivity, which is in agreement with the room temperature conductivity results. Thermal analysis of the semi-IPN lends further support to this observation. The temperature dependence of conductivity is found to follow the Arrhenius behavior at low temperatures (∼ upto 328 K) and VTF dependence at higher temperatures. This crossover in temperature dependent conductivity is attributed to the change in the phase morphology of the semi-IPNs beyond the crystalline melting temperature (T_m1) of the polyether segments.     

Ion binding properties of poly(ethylene oxide)-based networks in dioxane and toluene

Binding constants of alkali picrates to poly(ethylene oxide)-based networks were measured spectrophotometrically in dioxane at 25 and 40°C. The networks were synthesized from aliphatic tri- or tetrafunctional isocyanates and α,ω-diamino-poly-(ethylene glycol)s. The slopes of the Klotz binding plots appear to decrease in the lower picrate concentration range, suggesting that binding of the salt becomes more difficult at high picrate content. It was shown that under saturation conditions six to seven ethylene oxide units are required to bind a sodium picrate ion pair. The affinity of the PEO-resins for the alkali picrate can be enhanced by immobilizing a poly(crown ether) in the network. A number of competition experiments for sodium picrate in toluene was also carried out to obtain the affinity of soluble ligands for alkali salts. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1819–1824, 1997     

Synthesis and properties of poly(ethylene oxide)‐grafted polyethylene copolymer and terpolymer

A series of graft copolymers were synthesized based on ethylene‐co‐m,p‐methylstyrene (EMS) (backbone copolymer), ethylene‐1‐hexene‐m,p‐methylstyrene (EHMS) (backbone terpolymer), and polyethylene glycol monomethyl ethers (PEGM) (grafts) in this study. The PEGMs with molecular weights of 750 and 2000 were used. The chemical composition of the graft copolymers was analyzed by NMR and DSC measurements. The graft copolymers exhibited a phase‐separated morphology with the backbone and the methoxy polyethylene glycol (MPEG) grafts forming separate crystalline phases. The MPEG phase had a melting temperature lower than the corresponding MPEG homopolymer, as determined by DSC. The melting point of the crystalline phase formed by the EMS and EHMS main chains was lower than that of pure polymer backbone. Copyright © 2009 John Wiley & Sons, Ltd.     

Single-step synthesis of proton conducting poly(vinylidene fluoride) (PVDF) graft copolymer electrolytes

The single-step synthesis of proton conducting poly(vinylidene fluoride) (PVDF) graft copolymer electrolytes is demonstrated. The graft copolymers of PVDF backbone with poly(sulfopropyl methacrylate) (PVDF-g-PSPMA) and poly(styrene sulfonic acid) (PVDF-g-PSSA) were synthesized using PVDF as a macroinitiator for atom transfer radical polymerization (ATRP). ¹H NMR and FT-IR spectroscopy show that the “grafting from” method using ATRP was successful and the maximum grafting degrees were 35 and 25 wt% for PVDF-g-PSPMA and PVDF-g-PSSA, respectively. The IEC values were 0.63 and 0.45 meq/g, the water uptakes were 46.8 and 33.4 wt% and the proton conductivities were 0.015 and 0.007 S/cm at room temperature, for PVDF-g-PSPMA and PVDF-g-PSSA, respectively. Both membranes exhibited excellent thermal stability up to around 350 °C, verified by thermal gravimetric analysis (TGA).     

Synthesis and properties of segmented block copolymers based on mixtures of poly(ethylene oxide) and poly(tetramethylene oxide) segments

The synthesis and characterisation of segmented block copolymers based on mixtures of hydrophilic poly(ethylene oxide) and hydrophobic poly(tetramethylene oxide) polyether segments and monodisperse crystallisable bisester tetra-amide segments are reported. The PEO length was varied from 600 to 8000 g/mol and the PTMO length was varied from 650 to 2900 g/mol. The influence of the polyether phase composition on the thermal mechanical and the elastic properties of the resulting copolymers was studied.The use of high melting monodisperse tetra-amide segments resulted in a fast and almost complete crystallisation of the rigid segment. The copolymers had only one polyether glass transition temperature, which suggests that the amorphous polyether segments were homogenously mixed. Thermal analysis of the copolymers showed one polyether melting temperature that was lower than in the case of ideal co-crystallisation between the two polyether segments. However, at PEO or PTMO lengths larger than 2000 g/mol two polyether melting temperatures were observed. The copolymer with the best low temperature properties was based on a mixture of PEO and PTMO segments, both having a molecular weight of 1000 g/mol, at a weight ratio of 30/70.     

星形聚氧乙烯及星形杂臂氧化乙烯-苯乙烯共聚物的合成

以原子转移自由基偶联法合成了多臂星形聚合物S-PEO和星形杂臂共聚物PEO-PS。以傅立叶红外光谱(FT-IR)和核磁共振(1H NMR)分析方法确定了产物的结构。以GPC分析测试了产物的分子量和分子量分布。GPC分析结果表明所得聚合物分子量增大,分子量分布窄,偶联反应效率可高达99%以上。     

Amphiphilic polymer gel electrolytes. I. preparation of gels based on poly(ethylene oxide) graft copolymers containing different ionophobic groups

Amphiphilic graft copolymers were prepared via the radical copolymerization of poly(ethylene oxide) (PEO) macromonomers with fluorocarbon or hydrocarbon acrylates in toluene with 2,2′‐azobisisobutyronitrile (AIBN) as an initiator. ¹H NMR spectroscopy confirmed that the composition of the graft copolymers corresponded well to the monomer feed. For gel electrolytes prepared from the amphiphilic copolymers, the nature of the ionophobic parts of the amphiphilic graft copolymers had a great influence on the ion conductivity. Gel electrolytes based on graft copolymers containing fluorocarbon side chains showed significantly higher ion conductivity than electrolytes based on graft copolymers containing hydrocarbon groups. The ambient‐temperature ion conductivity was about 2.6 mS/cm at 20 °C for a gel electrolyte based on an amphiphilic graft copolymer consisting of an acrylate backbone carrying PEO and fluorocarbon side chains. Corresponding gels based on graft copolymers with PEO side chains and hydrocarbon groups showed an ambient‐temperature ion conductivity of about 1.2 mS/cm. The gel electrolytes contained 30 wt % copolymer and 70 wt % 1 M LiPF₆ in an ethylene carbonate/γ‐butyrolactone (2/1 w/w) mixture. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2223–2232, 2001